MAINTAINERS: Add missing boards and config entries

As part of my usual round of build testing, output about missing
MAINTAINERS information was not logged, and thus often overlooked.
Correct that mi

MAINTAINERS: Add missing boards and config entries

As part of my usual round of build testing, output about missing
MAINTAINERS information was not logged, and thus often overlooked.
Correct that mistake by ensuring that I log the output of
genboardscfg.py every time. As part of that, address a number of
missing MAINTAINERS entires. In the case of a missing file, I have put
the original submitter down. In the rest of the cases I have added the
config (and sometimes relevant header file) to the existing set of file
globs.

Change-Id: Ic4524445489daba323d638470c369ad914d5bfef
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
(cherry picked from commit 79df00fdb40b4584919c8bcef42d323a8d38d0f1)

show more ...

Merge git://git.denx.de/u-boot-sunxi

Update A20-OLinuXino-Lime2-eMMC_defconfig to include CONFIG_SCSI

Signed-off-by: Tom Rini <trini@konsulko.com>

sun50i: a64: Add A64-OLinuXino initial support

OLimex A64-OLinuXino is an open-source hardware board
using the Allwinner A64 SOC.

OLimex A64-OLinuXino has
- A64 Quad-core Cortex-A53 64bit
- 1GB or

sun50i: a64: Add A64-OLinuXino initial support

OLimex A64-OLinuXino is an open-source hardware board
using the Allwinner A64 SOC.

OLimex A64-OLinuXino has
- A64 Quad-core Cortex-A53 64bit
- 1GB or 2GB RAM DDR3L @ 672Mhz
- microSD slot and 4/8/16GB eMMC
- Debug TTL UART
- HDMI
- LCD
- IR receiver
- 5V DC power supply

Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

show more ...

sun50i: a64: Add initial NanoPi A64 support

NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.

Nanopi A64 features
- Allwinner A64,

sun50i: a64: Add initial NanoPi A64 support

NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.

Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>

show more ...

sun7i: Add support for Olimex A20-OLinuXino-LIME2-eMMC

This patch adds support for the Olimex OLinuXino Lime2 with eMMC flash
storage.
https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXino-LIM

sun7i: Add support for Olimex A20-OLinuXino-LIME2-eMMC

This patch adds support for the Olimex OLinuXino Lime2 with eMMC flash
storage.
https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXino-LIME2-eMMC/

It is a assembly variant of the regular Lime2 but featuring eMMC for
storage.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-sunxi

sun50i: h5: Add initial NanoPi NEO2 support

NanoPi NEO2 is designed and developed by FriendlyElec
using the Allwinner 64-bit H5 SOC.

NanoPi Neo2 key features
- Allwinner H5, Quad-core 64-bit Cortex

sun50i: h5: Add initial NanoPi NEO2 support

NanoPi NEO2 is designed and developed by FriendlyElec
using the Allwinner 64-bit H5 SOC.

NanoPi Neo2 key features
- Allwinner H5, Quad-core 64-bit Cortex-A53
- 512MB DDR3 RAM
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC MicroUSB power-supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>

show more ...

sun50i: a64: Add initial Orangepi Win/WinPlus support

Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.

A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A

sun50i: a64: Add initial Orangepi Win/WinPlus support

Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.

A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>

show more ...

sun50i: h5: Add initial Orangepi Zero Plus 2 support

Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 51

sun50i: h5: Add initial Orangepi Zero Plus 2 support

Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>

show more ...

sunxi: add a defconfig for SoPine w/ official baseboard

The SoPine is a SoM by Pine64, with an Allwinner A64 SoC, a LPDDR3 DRAM
chip, an AXP803 PMIC, a SPI NOR Flash and a MicroSD slot. The card
det

sunxi: add a defconfig for SoPine w/ official baseboard

The SoPine is a SoM by Pine64, with an Allwinner A64 SoC, a LPDDR3 DRAM
chip, an AXP803 PMIC, a SPI NOR Flash and a MicroSD slot. The card
detect pin of the MicroSD slot is broken, however, it doesn't matter as
the design of SoPine didn't allow hot-swapping the MicroSD card (The
MicroSD slot is at the back of the SoM, and when the SoM is installed on
the baseboard, it's nearly impossible to remove the MicroSD).

The official baseboard of it is a board with nearly the same connectors
with the original Pine64+, with the MicroUSB power jack replaced, and
at the position of MicroSD slot a eMMC module slot is added.

Add support for SoPine with the official baseboard by adding its
defconfig file. It still uses the device tree of Pine64, however, it
will change after a proper device tree of SoPine with baseboard is
accepted by Linux mainline.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Update board/sunxi/MAINTAINERS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>

show more ...

sun8i: h3: Add initial NanoPi M1 Plus support

NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.

NanoPi M

sun8i: h3: Add initial NanoPi M1 Plus support

NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.

NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>

show more ...

Merge git://git.denx.de/u-boot-sunxi

sun50i: h5: Add initial Orangepi Prime support

Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL

sun50i: h5: Add initial Orangepi Prime support

Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT

Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9

U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology

CPU: Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

sun50i: a64: Add initial Banana Pi M64 support

BPI-M64 is a 64-bit quad-core mini single board computer
using the Allwinner A64 SOC.

BPI-M64 features
- 1.2 Ghz Quad-Core ARM Cortex A53
- 2GB DDR3 S

sun50i: a64: Add initial Banana Pi M64 support

BPI-M64 is a 64-bit quad-core mini single board computer
using the Allwinner A64 SOC.

BPI-M64 features
- 1.2 Ghz Quad-Core ARM Cortex A53
- 2GB DDR3 SDRAM with 733MHz
- MicroSD/eMMC(8GB)
- 10/100/1000Mbps ethernet (Realtek RTL8211E/D)
- Wifi + BT
- IR receiver
- Audio In/Out
- Video In/Out
- 5V 2A DC power-supply

For dts file,
Sync with Linux commit 4879b7ae("Merge tag 'dmaengine-4.12-rc1'").

Boot from MMC:
-------------
U-Boot SPL 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
NOTICE: Configuring AXP PMIC
NOTICE: PMIC: setup successful
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9

U-Boot 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31 +0000) Allwinner Technology

CPU: Allwinner A64 (SUN50I)
Model: BananaPi-M64
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
Net: No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot: 0

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

sunxi: Add support for NanoPi M1

NanoPi M1 is a board based on Allwinner H3 CPU.

This commit adds the support for this platform with:
- an include device tree which enables UART, LEDs, GPIO key

sunxi: Add support for NanoPi M1

NanoPi M1 is a board based on Allwinner H3 CPU.

This commit adds the support for this platform with:
- an include device tree which enables UART, LEDs, GPIO key switch,
1 USB host ports and the SD-card as a dtsi file.
- a device tree specific to this board that enables the
2 additional USB ports
- a defconfig file for minimal support
- a section in MAINTAINERS (add myself)

Synchronized with the kernel device tree, from commits:
sun8i-nanopi.dtsi: 85d2913614d9ab899d23b7ab7d22d23cf45bd1de
sun8i-h3-nanopi-m1.dts: 10efbf5f16336b7540ad6a16aa1cb0b26bab033b

Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

show more ...

Merge git://git.denx.de/u-boot-sunxi

trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).

Signed-off-by: Tom

Merge git://git.denx.de/u-boot-sunxi

trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

sunxi: Move maintainership for Pine64

After speaking to Hans at FOSDEM, he is fine with transferring the
maintainership of the Pine64 boards over to me.

Signed-off-by: Andre Przywara <andre.przywar

sunxi: Move maintainership for Pine64

After speaking to Hans at FOSDEM, he is fine with transferring the
maintainership of the Pine64 boards over to me.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge branch 'master' of git://git.denx.de/u-boot-sunxi

sunxi: add support for Banana Pi M2 Plus board

Banana Pi M2 Plus is an Allwinner H3-based SBC by Sinovoip, which has
already mainline device tree file that have landed into U-Boot source
tree.

Add

sunxi: add support for Banana Pi M2 Plus board

Banana Pi M2 Plus is an Allwinner H3-based SBC by Sinovoip, which has
already mainline device tree file that have landed into U-Boot source
tree.

Add a defconfig file for it and add the MAINTAINERS items.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

Merge git://git.denx.de/u-boot-sunxi

sunxi: add support for Lichee Pi Zero

Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in productio

sunxi: add support for Lichee Pi Zero

Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in production batch), a 40-pin RGB LCD connector and some extra
pins available as 2.54mm pins or stamp holes.

Add support for it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

sunxi: Add support for Bananapi M2 Ultra

The Bananapi M2 Ultra is the first publicly available development board
featuring the R40 SoC.

This patch add barebone dtsi/dts files for the R40 and Banana

sunxi: Add support for Bananapi M2 Ultra

The Bananapi M2 Ultra is the first publicly available development board
featuring the R40 SoC.

This patch add barebone dtsi/dts files for the R40 and Bananapi M2 Ultra,
as well as a defconfig for it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

sunxi: Add maintainer of the NanoPi NEO Air

Add myself as maintainer of the NanoPi NEO Air board.

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Reviewed-by: Jagan Teki <jagan@openedev.com>

Merge branch 'master' of git://git.denx.de/u-boot-sunxi