| #
00caae6d |
| 03-Aug-2017 |
Simon Glass <sjg@chromium.org> |
env: Rename getenv/_f() to env_get()
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few place
env: Rename getenv/_f() to env_get()
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
show more ...
|
| #
ce38ebb6 |
| 16-Mar-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://git.denx.de/u-boot-fsl-qoriq
|
| #
29ca713c |
| 19-Jan-2017 |
Priyanka Jain <priyanka.jain@nxp.com> |
armv8: fsl-lsch3: Update VID support
VID support in NXP layerscape Chassis-3 (lsch3) compilant SoCs like
LS2088A, LS2080A differs from existing logic.
-VDD voltage array is different
-Registers are
armv8: fsl-lsch3: Update VID support
VID support in NXP layerscape Chassis-3 (lsch3) compilant SoCs like
LS2088A, LS2080A differs from existing logic.
-VDD voltage array is different
-Registers are different
-VDD calculation logic is different
Add new function adjust_vdd() for LSCH3 compliant SoCs
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Arpit Goel <arpit.goel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
show more ...
|
| #
cbe7706a |
| 26-Sep-2016 |
Tom Rini <trini@konsulko.com> |
Merge git://git.denx.de/u-boot-fsl-qoriq
trini: Drop local memset() from
examples/standalone/mem_to_mem_idma2intr.c
Signed-off-by: Tom Rini <trini@konsulko.com>
|
| #
126fe70d |
| 07-Sep-2016 |
Shaohui Xie <Shaohui.Xie@nxp.com> |
armv8: ls1046aqds: Add LS1046AQDS board support
LS1046AQDS Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 51
armv8: ls1046aqds: Add LS1046AQDS board support
LS1046AQDS Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
show more ...
|
| #
0badc648 |
| 29-Mar-2016 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq
|
| #
ed2530d0 |
| 23-Mar-2016 |
Rai Harninder <harninder.rai@nxp.com> |
armv8/ls2080ardb: Enable VID support
This patch enable VID support for ls2080ardb platform.
It uses the common VID driver.
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Reviewed-by: York Sun
armv8/ls2080ardb: Enable VID support
This patch enable VID support for ls2080ardb platform.
It uses the common VID driver.
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
show more ...
|
| #
55926ddd |
| 22-Mar-2016 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq
|
| #
1be8d10b |
| 09-Mar-2016 |
Wenbin Song <wenbin.song@nxp.com> |
freescale: vid: Return i2c mux to default channel
IR chip is on one of the channels on multiplexed I2C-bus.
Reset to default channel after accessing.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com
freescale: vid: Return i2c mux to default channel
IR chip is on one of the channels on multiplexed I2C-bus.
Reset to default channel after accessing.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
show more ...
|
| #
d8247774 |
| 25-Jan-2016 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
|
| #
2f66a828 |
| 22-Jan-2016 |
Ying Zhang <b40530@freescale.com> |
powerpc/board/t4240rdb: Enable VID support
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory. These values
define the voltage requirements for the
powerpc/board/t4240rdb: Enable VID support
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory. These values
define the voltage requirements for the chip. u-boot reads
FUSESR and translates the values into the appropriate
commands to set the voltage output value of an external
voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
show more ...
|
| #
cabe4d2f |
| 22-Jan-2016 |
Ying Zhang <b40530@freescale.com> |
board/freescale/common: Check IR chip mode for VID support
IR chip on all the boards are required to be used in Intel mode
to support VID. VDD will not be adjusted if IR chip is used in
other modes.
board/freescale/common: Check IR chip mode for VID support
IR chip on all the boards are required to be used in Intel mode
to support VID. VDD will not be adjusted if IR chip is used in
other modes.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
show more ...
|
| #
1670c8c2 |
| 30-Nov-2015 |
Tom Rini <trini@konsulko.com> |
Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq
|
| #
02b5d2ed |
| 11-Nov-2015 |
Shaohui Xie <Shaohui.Xie@freescale.com> |
armv8/ls1043aqds: add LS1043AQDS board support
LS1043AQDS Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 DIMM
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND f
armv8/ls1043aqds: add LS1043AQDS board support
LS1043AQDS Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 DIMM
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two RGMII ports
* XFI 10G port
* SGMII
* QSGMII with 4x 1G ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
show more ...
|
| #
272a1acf |
| 08-Dec-2014 |
Tom Rini <trini@ti.com> |
Merge git://git.denx.de/u-boot-mpc85xx
|
| #
3ad2737e |
| 31-Oct-2014 |
Ying Zhang <b40530@freescale.com> |
powerpc/t208xqds: VID support
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot
powerpc/t208xqds: VID support
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
show more ...
|