| c0e29727 | 06-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
icorem6: Use drive strength macros
Use driver strength macros instead of hex numbers. - IMX6DQ_DRIVE_STRENGTH - 0x30 - IMX6SDL_DRIVE_STRENGTH - 0x28
Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Li
icorem6: Use drive strength macros
Use driver strength macros instead of hex numbers. - IMX6DQ_DRIVE_STRENGTH - 0x30 - IMX6SDL_DRIVE_STRENGTH - 0x28
Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
show more ...
|
| d456ab07 | 06-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
icorem6: Use proper iomux_ddr_regs drive strength values
Usually the drive strength values for DQ and SDL are 0x30 and 0x28 respectively, update them accordingly.
Cc: Stefano Babic <sbabic@denx.de>
icorem6: Use proper iomux_ddr_regs drive strength values
Usually the drive strength values for DQ and SDL are 0x30 and 0x28 respectively, update them accordingly.
Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
show more ...
|
| b805b174 | 06-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
engicam: Move uart mux init to SPL
Since, u-boot handle fdt through uart so move the UART code to SPL instead make it to global area.
Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi
engicam: Move uart mux init to SPL
Since, u-boot handle fdt through uart so move the UART code to SPL instead make it to global area.
Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
show more ...
|
| 4bbd4059 | 06-May-2017 |
Jagan Teki <jagan@amarulasolutions.com> |
icorem6: Add mmc_late_init
Let the runtime code can set the mmcdev and mmcroot based on the devno using mmc_get_env_dev instead of defining separately in build-time configs using mmc_late_init func.
icorem6: Add mmc_late_init
Let the runtime code can set the mmcdev and mmcroot based on the devno using mmc_get_env_dev instead of defining separately in build-time configs using mmc_late_init func.
Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
show more ...
|
| 023ff2f7 | 25-Oct-2016 |
Jagan Teki <jagan@amarulasolutions.com> |
imx6: icorem6: Add NAND support
Add NAND support for Engicam i.CoreM6 qdl board.
Boot Log: --------
U-Boot SPL 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43) Trying to boot from NAND NA
imx6: icorem6: Add NAND support
Add NAND support for Engicam i.CoreM6 qdl board.
Boot Log: --------
U-Boot SPL 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43) Trying to boot from NAND NAND : 512 MiB
U-Boot 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43 +0530)
CPU: Freescale i.MX6SOLO rev1.3 at 792MHz CPU: Industrial temperature grade (-40C to 105C) at 55C Reset cause: WDOG Model: Engicam i.CoreM6 DualLite/Solo Starter Kit DRAM: 256 MiB NAND: 512 MiB MMC: FSL_SDHC: 0 In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 icorem6qdl>
Cc: Scott Wood <oss@buserror.net> Cc: Stefano Babic <sbabic@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
show more ...
|
| 5c0d38f6 | 08-Oct-2016 |
Jagan Teki <jagan@amarulasolutions.com> |
arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
i.CoreM6 Quad/Dual modules are system on module solutions manufactured by Engicam with following characteristics: CPU NXP
arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
i.CoreM6 Quad/Dual modules are system on module solutions manufactured by Engicam with following characteristics: CPU NXP i.MX6 DQ, 800MHz RAM 1GB, 32, 64 bit, DDR3-800/1066 NAND SLC,512MB Power supply Single 5V MAX LCD RES FULLHD
and more info at http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
show more ...
|
| f160c5c8 | 25-Oct-2016 |
Jagan Teki <jagan@amarulasolutions.com> |
engicam: icorem6: Add DM_GPIO, DM_MMC support
Add DM_GPIO, DM_MMC support for u-boot and disable for SPL.
Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio
engicam: icorem6: Add DM_GPIO, DM_MMC support
Add DM_GPIO, DM_MMC support for u-boot and disable for SPL.
Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
show more ...
|
| 58413366 | 08-Oct-2016 |
Jagan Teki <jagan@amarulasolutions.com> |
imx6: icorem6: Add ENET support
Add enet support for engicam icorem6 qdl starter kit. - Add pinmux settings - Add board_eth_init
TFTP log: -------- Net: FEC [PRIME] Hit any key to stop autoboot:
imx6: icorem6: Add ENET support
Add enet support for engicam icorem6 qdl starter kit. - Add pinmux settings - Add board_eth_init
TFTP log: -------- Net: FEC [PRIME] Hit any key to stop autoboot: 0 icorem6qdl> tftpboot {fdt_addr} imx6dl-icore.dtb Using FEC device TFTP from server 192.168.2.96; our IP address is 192.168.2.75 Filename 'imx6dl-icore.dtb'. Load address: 0x0 Loading: ###### 1.3 MiB/s done Bytes transferred = 28976 (7130 hex) CACHE: Misaligned operation at range [00000000, 00007130] icorem6qdl>
Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
show more ...
|