x86: conga-qeval20-qa3-e3845.dts: Enable xHCI support in dts

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

Merge git://git.denx.de/u-boot-x86

x86: baytrail: Change lpe/lpss-sio/scc FSP properties to integer

At present lpe/lpss-sio/scc FSP properties are all boolean, but in
fact for "enable-lpe" it has 3 possible options. This adds macros

x86: baytrail: Change lpe/lpss-sio/scc FSP properties to integer

At present lpe/lpss-sio/scc FSP properties are all boolean, but in
fact for "enable-lpe" it has 3 possible options. This adds macros
for these options and change the property from a boolean type to
an integer type, and change their names to explicitly indicate what
the property is really for.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

x86: baytrail: Use macros instead of magic numbers for FSP settings

Introduce various meaningful macros for FSP settings and switch over
to use them instead of magic numbers.

Signed-off-by: Bin Men

x86: baytrail: Use macros instead of magic numbers for FSP settings

Introduce various meaningful macros for FSP settings and switch over
to use them instead of magic numbers.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

x86: baytrail: Change "fsp, mrc-init-tseg-size" default value to 1

The default value of "fsp,mrc-init-tseg-size" should be 1 (1MB) per
FSP default settings. 0 is not valid.

Signed-off-by: Bin Meng

x86: baytrail: Change "fsp, mrc-init-tseg-size" default value to 1

The default value of "fsp,mrc-init-tseg-size" should be 1 (1MB) per
FSP default settings. 0 is not valid.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

Merge git://git.denx.de/u-boot-x86

x86: ich6_gpio: Add use-lvl-write-cache for I/O access mode

Add a device-tree property use-lvl-write-cache that will cause
writes to lvl to be cached instead of read from lvl before each
write. This

x86: ich6_gpio: Add use-lvl-write-cache for I/O access mode

Add a device-tree property use-lvl-write-cache that will cause
writes to lvl to be cached instead of read from lvl before each
write. This is required on some platforms that have the register
implemented as dual read/write (such as Baytrail).

Prior to this fix the blue USB port on the Minnowboard Max was
unusable since USB_HOST_EN0 was set high then immediately set
low when USB_HOST_EN1 was written.

This also resolves the 'gpio clear | set' command warning like:
"Warning: value of pin is still 0"

Signed-off-by: George McCollister <george.mccollister@gmail.com>
<rebased on latest origin/master, fixed all baytrail boards>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-x86

x86: conga-qeval20-qa3: Add SMBus support and SMSC2513 config code

This patch includes the following changes:

- Remove Designware I2C support from dts as its not used
- Configure SMBus PADs in dts

x86: conga-qeval20-qa3: Add SMBus support and SMSC2513 config code

This patch includes the following changes:

- Remove Designware I2C support from dts as its not used
- Configure SMBus PADs in dts
- Enable I2C commands and I2C support
- Configure SMSC2513 USB hub via SMBus upon startup
- Move environment location to match Minnowmax example
- Enhancement of the default environment

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge branch 'master' of git://git.denx.de/u-boot-x86

x86: baytrail: Configure card detect pin of the SD controller

As of today, the latest version FSP (gold4) for BayTrail misses the
PAD configuration of the SD controller's Card Detect signal. The
def

x86: baytrail: Configure card detect pin of the SD controller

As of today, the latest version FSP (gold4) for BayTrail misses the
PAD configuration of the SD controller's Card Detect signal. The
default PAD value for the CD pin sets the pin to work in GPIO mode,
which causes card detect status cannot be reflected by the Present
State register in the SD controller (bit 16 & bit 18 are always zero).

Add a configuration for this pin in the pinctrl node.

Note I've checked the PAD configuration for all the pins in all the
3 controllers (eMMC/SDIO/SD). Only this SDMMC3_CD_B pin does not get
initialized to correct mode by FSP. With fsp,emmc-boot-mode set to
2 (eMMC 4.1), eMMC pins are initialized to func 1, but if we set
fsp,emmc-boot-mode to 1 (auto), those pins are initialized to func 3
which is correct according to datasheet.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

x86: baytrail: Change fsp, emmc-boot-mode to "auto"

At present all BayTrail boards configure fsp,emmc-boot-mode to 2,
which means "eMMC 4.1" per FSP documentation. However, eMMC 4.1
only shows up on

x86: baytrail: Change fsp, emmc-boot-mode to "auto"

At present all BayTrail boards configure fsp,emmc-boot-mode to 2,
which means "eMMC 4.1" per FSP documentation. However, eMMC 4.1
only shows up on some early stepping silicon of BayTrail SoC.
Newer stepping SoC integrates an eMMC 4.5 controller. Intel FSP
provides a config option fsp,emmc-boot-mode which tells FSP which
eMMC controller it initializes. Instead of hardcoded to 2, now
we change it to 1 which means "auto".

With this change, MinnowMax board (with a D0 stepping BayTrail SoC)
can see the eMMC 4.5 controller at PCI address 00.17.00 via U-Boot
'pci' command.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

x86: baytrail: Add 'reg' property in the pinctrl node

Without a 'reg' property, pinctrl driver probe routine fails in
its pre_probe() with a return value of -EINVAL.

Add 'reg' property for all BayT

x86: baytrail: Add 'reg' property in the pinctrl node

Without a 'reg' property, pinctrl driver probe routine fails in
its pre_probe() with a return value of -EINVAL.

Add 'reg' property for all BayTrail boards. Note for BayleyBay,
the pinctrl node is newly added.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-x86

x86: Use latest microcode for all BayTrail boards

Update board device tree to include latest microcode, and remove
the old no longer needed microcode.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
R

x86: Use latest microcode for all BayTrail boards

Update board device tree to include latest microcode, and remove
the old no longer needed microcode.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

x86: dts: Update to include ACTL register details

This updates all x86 boards that currently have IRQ router in the
dts files to include ACTL register details.

Signed-off-by: Bin Meng <bmeng.cn@gma

x86: dts: Update to include ACTL register details

This updates all x86 boards that currently have IRQ router in the
dts files to include ACTL register details.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

x86: Add congatec conga-QA3/E3845-4G (Bay Trail) support

This patch adds support for the congatec conga-QA3/E3845-4G eMMC8 SoM,
installed on the congatec Qseven 2.0 evaluation carrier board
(conga-Q

x86: Add congatec conga-QA3/E3845-4G (Bay Trail) support

This patch adds support for the congatec conga-QA3/E3845-4G eMMC8 SoM,
installed on the congatec Qseven 2.0 evaluation carrier board
(conga-QEVAL).

Its port is very similar to the MinnowboardMAX port and also uses
the Intel FSP as described in doc/README.x86.

Currently supported are the following interfaces / devices:
- UART (via Winbond legacy SuperIO chip on carrier board)
- Ethernet (PCIe Intel I210 / E1000)
- SPI including SPI NOR as boot-device
- USB 2.0
- SATA via U-Boot SCSI IF
- eMMC
- Video (HDMI output @ 800x600)
- PCIe

Not supported yet is:
- I2C
- USB 3.0

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

show more ...