ARM: OMAP5: Enable support for AVS0 for OMAP5 production devices

OMAP5432 did go into production with AVS class0 registers which were
mutually exclusive from AVS Class 1.5 registers.

Most OMAP5-uEV

ARM: OMAP5: Enable support for AVS0 for OMAP5 production devices

OMAP5432 did go into production with AVS class0 registers which were
mutually exclusive from AVS Class 1.5 registers.

Most OMAP5-uEVM boards use the pre-production Class1.5 which has
production efuse registers set to 0. However on production devices,
these are set to valid data.

scale_vcore logic is already smart enough to detect this and use the
"Nominal voltage" on devices that do not have efuse registers populated.

On a test production device populated as follows:
MPU OPP_NOM:
=> md.l 0x04A0021C4 1
4a0021c4: 03a003e9 ....
(0x3e9 = 1.01v) vs nom voltage of 1.06v
MPU OPP_HIGH:
=> md.l 0x04A0021C8 1
4a0021c8: 03400485 ..@.

MM OPP_NOM:
=> md.l 0x04A0021A4 1
4a0021a4: 038003d4 ....
(0x3d4 = 980mV) vs nom voltage of 1.025v
MM OPP_OD:
=> md.l 0x04A0021A8 1
4a0021a8: 03600403 ..`.

CORE OPP_NOM:
=> md.l 0x04A0021D8 1
4a0021d8: 000003cf ....
(0x3cf = 975mV) vs nom voltage of 1.040v

Since the efuse values are'nt currently used, we do not regress on
existing pre-production samples (they continue to use nominal voltage).

But on boards that do have production samples populated, we can leverage
the optimal voltages necessary for proper operation.

Tested on:
a) 720-2644-001 OMAP5UEVM with production sample.
b) 750-2628-222(A) UEVM5432G-02 with pre-production sample.

Data based on OMAP5432 Technical reference Manual SWPU282AF (May
2012-Revised Aug 2016)

NOTE: All collaterals on OMAP5432 silicon itself seems to have been
removed from ti.com, though EVM details are still available:
http://www.ti.com/tool/OMAP5432-EVM

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge git://git.denx.de/u-boot-dm

arm: omap: sata: move enable sata clocks to enable_basic_clocks()

All the clocks which has to be enabled has to be done in
enable_basic_clocks(), so moving enable sata clock to common
clocks enable

arm: omap: sata: move enable sata clocks to enable_basic_clocks()

All the clocks which has to be enabled has to be done in
enable_basic_clocks(), so moving enable sata clock to common
clocks enable function.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: OMAP5+: Remove unsed dpll structures

Latest gcc compile strted complaining about defined structure definition
that are not used. Remove the unused sturctures.

Reported-by: Dan Murphy <dmurphy@

ARM: OMAP5+: Remove unsed dpll structures

Latest gcc compile strted complaining about defined structure definition
that are not used. Remove the unused sturctures.

Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

board: ti: dra71x-evm: Add PMIC support

Add the pmic_data for LP873x PMIC which is used to power
up dra71x-evm.

Note: As per the DM[1] DRA71x supports only OP_NOM. So, updating
the efuse registers

board: ti: dra71x-evm: Add PMIC support

Add the pmic_data for LP873x PMIC which is used to power
up dra71x-evm.

Note: As per the DM[1] DRA71x supports only OP_NOM. So, updating
the efuse registers only to use OPP_NOM irrespective of any
CONFIG_DRA7_<VOLT>_OPP_{NOM,od,high} is defined.

[1] http://www.ti.com/product/DRA718/technicaldocuments

Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: OMAP4+: Add support for dynamically selecting OPPs

It can be expected that different paper spins of a SoC can have
different definitions for OPP and can have their own constraints
on the boot u

ARM: OMAP4+: Add support for dynamically selecting OPPs

It can be expected that different paper spins of a SoC can have
different definitions for OPP and can have their own constraints
on the boot up OPP for each voltage rail. In order to have this
flexibility, add support for dynamically selecting the OPP voltage
based on the board to handle any such exceptions.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: DRA7x/AM57xx: Get rid of CONFIG_AM57XX

CONFIG_AM57XX is just an unnecessary macro that is redundant given So,
remove the same instead of spreading through out the u-boot source
code and getting

ARM: DRA7x/AM57xx: Get rid of CONFIG_AM57XX

CONFIG_AM57XX is just an unnecessary macro that is redundant given So,
remove the same instead of spreading through out the u-boot source
code and getting in the way to maintain common code for DRA7x family.

Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

arm: Introduce arch/arm/mach-omap2 for OMAP2 derivative platforms

This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,oma

arm: Introduce arch/arm/mach-omap2 for OMAP2 derivative platforms

This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories. All refernces to the former locations are updated to
the current locations. For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...