env: Rename getenv/_f() to env_get()

We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few place

env: Rename getenv/_f() to env_get()

We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

ARM: k2g: Program DDRPHY_DATX8 registers via mask and value variables

Different K2G evms may need to program the various
KS2_DDRPHY_DATX8_X_OFFSET registers in different ways. Therefore, use
the mas

ARM: k2g: Program DDRPHY_DATX8 registers via mask and value variables

Different K2G evms may need to program the various
KS2_DDRPHY_DATX8_X_OFFSET registers in different ways. Therefore, use
the mask and val registers for each KS2_DDRPHY_DATAX_X_OFFSET to
properly program the register.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: k2g: Program DDR PHY MR2 register with the default value

K2G GP doesn't require the MR2 register to be programed since the
default is good enough. However, newer K2G boards do need to change
th

ARM: k2g: Program DDR PHY MR2 register with the default value

K2G GP doesn't require the MR2 register to be programed since the
default is good enough. However, newer K2G boards do need to change
this register value. Therefore, instead of not writing this register if
ran on a K2G board just program the value to be written to match the
default/reset value.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: K2G: DDR3: Fix up priv ID for MPU

For ECC enabled DDR, we use EDMA to reset all memory values to 0. For
K2E/L/H/K the priv ID of 8 was indicative of ARM, but that is not the
case for K2G, where

ARM: K2G: DDR3: Fix up priv ID for MPU

For ECC enabled DDR, we use EDMA to reset all memory values to 0. For
K2E/L/H/K the priv ID of 8 was indicative of ARM, but that is not the
case for K2G, where it is 1.

Unfortunately, ddr3 code had hard coded the privID and had missed
identification previously. Fix the same, else unforeseen behavior can
be expected in our reset of DDR contents to 0 for ECC enablement.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

board: k2g: Enable ECC byte lane

Enable ECC byte lane for k2g-evm

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Merge branch 'master' of git://git.denx.de/u-boot

ARM: k2g: Add ddr3 info

Add ddr3 related info

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

Merge branch 'master' of git://git.denx.de/u-boot

Merge remote-tracking branch 'u-boot/master' into 'u-boot-arm/master'

ARM: keystone: move SoC sources to mach-keystone

Move
arch/arm/cpu/armv7/keystone/* -> arch/arm/mach-keystone/*

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>