| de6f604d | 24-Apr-2012 |
Troy Kisky <troy.kisky@boundarydevices.com> |
mxc_i2c: specify i2c base address in config file
The following platforms had their config files changed
flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd
and mx53loco.
Signed-off-by: Troy Ki
mxc_i2c: specify i2c base address in config file
The following platforms had their config files changed
flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd
and mx53loco.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
show more ...
|
| 05d4df1d | 31-May-2012 |
Fabio Estevam <fabio.estevam@freescale.com> |
mx6: Allow mx6 to access the IPUv3 registers
Adjust the IPUv3 registers, so that the IPUv3 driver can be extended for mx6 as well.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> |
| 895f3e05 | 10-Jul-2012 |
Wolfgang Denk <wd@denx.de> |
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
tegra: define fdt_load/fdt_high variables
tegra: enable bootz command
tegra: usb: Fix device e
Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
tegra: define fdt_load/fdt_high variables
tegra: enable bootz command
tegra: usb: Fix device enumeration problem of USB1
tegra: trimslice: set up serial flash pinmux
tegra: add pin_mux_spi() board initialization function
tegra: add GMC/GMD funcmux entry for SFLASH
tegra: bootcmd: start USB only when needed
tegra: bootcmd enhancements
tegra: add enterrcm command
tegra: enable CONFIG_ENV_VARS_UBOOT_CONFIG
Add env vars describing U-Boot target board
tegra: usb: fix wrong error check
tegra: add ULPI on USB2 funcmux entry
tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches
tegra: Add Tamonten Evaluation Carrier support
tegra: Use SD write-protect GPIO on Tamonten
tegra: Implement gpio_early_init() on Tamonten
tegra: Allow boards to perform early GPIO setup
tegra: plutux: Add device tree support
tegra: medcom: Add device tree support
tegra: Rework Tamonten support
beagle: add eeprom expansion board info for bct brettl4
Signed-off-by: Wolfgang Denk <wd@denx.de>
show more ...
|
| 8b3f7bf7 | 24-Jun-2012 |
Jim Lin <jilin@nvidia.com> |
tegra: usb: Fix device enumeration problem of USB1
A known hardware issue of USB1 port where bit 1 (connect status
change) of PORTSC register will be set after issuing Port Reset
(like "usb reset" i
tegra: usb: Fix device enumeration problem of USB1
A known hardware issue of USB1 port where bit 1 (connect status
change) of PORTSC register will be set after issuing Port Reset
(like "usb reset" in u-boot command line).
This will be treated as an error and stops later device enumeration.
Therefore we clear that bit after Port Reset in order to proceed
later device enumeration.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
show more ...
|
| a016e144 | 12-Jun-2012 |
Stephen Warren <swarren@nvidia.com> |
tegra: add GMC/GMD funcmux entry for SFLASH
This is used on TrimSlice.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com> |
| f97daaa2 | 31-May-2012 |
Lucas Stach <dev@lynxeye.de> |
tegra: add ULPI on USB2 funcmux entry
This is needed as a prerequisite for Tegra USB ULPI support
within U-Boot.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@wwwdot
tegra: add ULPI on USB2 funcmux entry
This is needed as a prerequisite for Tegra USB ULPI support
within U-Boot.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
show more ...
|
| 86d74d03 | 14-May-2012 |
Rajeshwari Shinde <rajeshwari.s@samsung.com> |
EXYNOS5: USB: Fix incorrect USB base addresses
This patch corrects the base addresses for USB_PHY and USB_OTG.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Rajeshwari Shind
EXYNOS5: USB: Fix incorrect USB base addresses
This patch corrects the base addresses for USB_PHY and USB_OTG.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
show more ...
|
| c48ac113 | 14-May-2012 |
Rajeshwari Shinde <rajeshwari.s@samsung.com> |
EXYNOS: Add power Enable/Disable for USB-EHCI
This patch adds functions to enable/disable the power of USB
host controller for EXYNOS5.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed
EXYNOS: Add power Enable/Disable for USB-EHCI
This patch adds functions to enable/disable the power of USB
host controller for EXYNOS5.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
show more ...
|
| 71045da8 | 14-May-2012 |
Rajeshwari Shinde <rajeshwari.s@samsung.com> |
USB: EXYNOS: Set USB 2.0 HOST Link mode
This patch adds a function to set usb host mode to USB 2.0 HOST Link
for EXYNOS5
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> |
| f9c4e04b | 14-May-2012 |
Rajeshwari Shinde <rajeshwari.s@samsung.com> |
EXYNOS5: Add structure for PMU registers
This patch adds power mananagement registers structure for exynos5 SoC.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Chander Kashya
EXYNOS5: Add structure for PMU registers
This patch adds power mananagement registers structure for exynos5 SoC.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
show more ...
|
| 775b6f72 | 14-May-2012 |
Rajeshwari Shinde <rajeshwari.s@samsung.com> |
EXYNOS5: Fix system register structure
This patch corrects the SYSREG structure.
We have removed the sysreg.h added in the previous patchset
version as the sysreg structure is already defined in sys
EXYNOS5: Fix system register structure
This patch corrects the SYSREG structure.
We have removed the sysreg.h added in the previous patchset
version as the sysreg structure is already defined in system.h.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
show more ...
|
| 7590d3ce | 21-May-2012 |
Rajeshwari Shinde <rajeshwari.s@samsung.com> |
USB: EXYNOS: Incorporate EHCI review comments
This patch incorates the review comments given by Minkyu Kang for
EHCI support on EXYNOS
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> |
| d519b4bc | 02-Apr-2012 |
Fabio Estevam <fabio.estevam@freescale.com> |
ARM: introduce arch_early_init_r()
Introduce arch_early_init_r() function, which can be useful for doing
early initialization after relocation has happened.
Signed-off-by: Fabio Estevam <fabio.este
ARM: introduce arch_early_init_r()
Introduce arch_early_init_r() function, which can be useful for doing
early initialization after relocation has happened.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
show more ...
|
| 4ae8bc43 | 03-Jan-2012 |
Stefan Roese <sr@denx.de> |
SPL: ARM: spear: Add SPL support for SPEAr600 platform
This patch adds SPL support for SPEAr600. Currently only SNOR
(Serial NOR) flash support is included. Other boot devices
(NAND, MMC, USB ...) m
SPL: ARM: spear: Add SPL support for SPEAr600 platform
This patch adds SPL support for SPEAr600. Currently only SNOR
(Serial NOR) flash support is included. Other boot devices
(NAND, MMC, USB ...) may be added with later patches.
Tested on the STM SPEAr600 evaluation and x600 SPEAr600 boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
show more ...
|
| 2cb06a4f | 14-Feb-2012 |
Stefan Roese <sr@denx.de> |
GPIO: Add SPEAr GPIO driver
Tested on x600 (SPEAr600).
Signed-off-by: Stefan Roese <sr@denx.de> |
| bc0bdf4c | 07-May-2012 |
Amit Virdi <amit.virdi@st.com> |
cleanup/SPEAr: Remove unnecessary parenthesis
In SPEAr configuration files, unnecessary paranthesis are used in some
\#defines. Remove them as they serve no purpose
Signed-off-by: Amit Virdi <amit.
cleanup/SPEAr: Remove unnecessary parenthesis
In SPEAr configuration files, unnecessary paranthesis are used in some
\#defines. Remove them as they serve no purpose
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
show more ...
|
| f28e5c94 | 07-May-2012 |
Shiraz Hashim <shiraz.hashim@st.com> |
SPEAr: Correct SoC ID offset in misc configuration space
SoC Core ID offset is 0x30 in miscellaneous configuration address
space. It was wrongly mentioned as periph2 clk enable.
Signed-off-by: Shir
SPEAr: Correct SoC ID offset in misc configuration space
SoC Core ID offset is 0x30 in miscellaneous configuration address
space. It was wrongly mentioned as periph2 clk enable.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
show more ...
|
| 7c885a0e | 07-May-2012 |
Shiraz Hashim <shiraz.hashim@st.com> |
SPEAr: explicitly select clk src for UART
UART in u-boot intends to run on 48MHz clock supplied by USB PLL.
Explicitly select the intended clock source.
Signed-off-by: Shiraz Hashim <shiraz.hashim@
SPEAr: explicitly select clk src for UART
UART in u-boot intends to run on 48MHz clock supplied by USB PLL.
Explicitly select the intended clock source.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
show more ...
|
| 962d026b | 07-May-2012 |
Vipin KUMAR <vipin.kumar@st.com> |
SPEAr: Add basic arch related support for SPEAr SoCs
Earlier, architecture specific init code was mixed with board initialization
code in board/spear/... This patch updates architecture support for
SPEAr: Add basic arch related support for SPEAr SoCs
Earlier, architecture specific init code was mixed with board initialization
code in board/spear/... This patch updates architecture support for SPEAr in
latest u-boot and prints the SoC information.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
show more ...
|
| 8eb0ee6a | 07-May-2012 |
Vipin KUMAR <vipin.kumar@st.com> |
SPEAr: Add macb driver support for spear310 and spear320
SPEAr310 and SPEAr320 SoCs have an extra ethernet controller. The
driver for this device is already supported by u-boot, so configuring
board
SPEAr: Add macb driver support for spear310 and spear320
SPEAr310 and SPEAr320 SoCs have an extra ethernet controller. The
driver for this device is already supported by u-boot, so configuring
board configuration file and defining base addresses etc to make use
of the common driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
show more ...
|
| deb00562 | 07-May-2012 |
Vipin KUMAR <vipin.kumar@st.com> |
SPEAr: Configure network support for spear SoCs
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de> |
| 70fdbefc | 07-May-2012 |
Amit Virdi <amit.virdi@st.com> |
SPEAr: Eliminate dependency on Xloader table
Xloader table was used primarily to inform u-boot about the DDR size. However,
now the ddr size is calculated at runtime which eliminates any need for th
SPEAr: Eliminate dependency on Xloader table
Xloader table was used primarily to inform u-boot about the DDR size. However,
now the ddr size is calculated at runtime which eliminates any need for the
Xloader table. So removing this unnecessary code.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
show more ...
|
| f3fcf92d | 07-May-2012 |
Vipin KUMAR <vipin.kumar@st.com> |
st_smi: Add support for SPEAr SMI driver
SMI is the serial memory interface controller provided by ST.
Earlier, a driver exists in the u-boot source code for the SMI IP. However, it
was specific to
st_smi: Add support for SPEAr SMI driver
SMI is the serial memory interface controller provided by ST.
Earlier, a driver exists in the u-boot source code for the SMI IP. However, it
was specific to spear platforms. This commit converts the same driver to a more
generic driver. As a result, the driver files are renamed to st_smi.c and
st_smi.h and moved into drivers/mtd folder for reusability by other platforms
using smi controller peripheral.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
show more ...
|
| 0def98e7 | 22-May-2012 |
Vipin KUMAR <vipin.kumar@st.com> |
mtd/NAND: Remove obsolete SPEAr specific NAND drivers
Since, SPEAr platform uses generic FSMC driver now, so spear specific files
drivers/mtd/nand/spr_nand.c, arch/arm/include/asm/arch-spear/spr_nan
mtd/NAND: Remove obsolete SPEAr specific NAND drivers
Since, SPEAr platform uses generic FSMC driver now, so spear specific files
drivers/mtd/nand/spr_nand.c, arch/arm/include/asm/arch-spear/spr_nand.h are
removed
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
show more ...
|
| 1fa943b9 | 22-May-2012 |
Vipin KUMAR <vipin.kumar@st.com> |
SPEAr: Configure FSMC driver for NAND interface
Since FSMC is a standard IP and it supports different memory interfaces, it
is supported independent of spear platform and spear is configured to use
SPEAr: Configure FSMC driver for NAND interface
Since FSMC is a standard IP and it supports different memory interfaces, it
is supported independent of spear platform and spear is configured to use that
driver for interfacing with the NAND device
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
show more ...
|