Merge branch 'master' of git://git.denx.de/u-boot

arm: am33xx: Initialize EMIF REG_PR_OLD_COUNT for BBB and am335x-evm

Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2,
and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x

arm: am33xx: Initialize EMIF REG_PR_OLD_COUNT for BBB and am335x-evm

Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2,
and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x-evm. With
the default values LCDC suffers from DMA FIFO underflows and frame
synchronization lost errors. The initialization values are the highest
that work flawlessly when heavy memory load is generated by CPU. 32bpp
colors were used in the test. On BBB the video mode used 110MHz pixel
clock. The mode supported by the panel of am335x-evm uses 30MHz pixel
clock.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: DRA7: DDR: Enable SR in Power Management Control

If EMIF is idle for certain amount of DDR cycles, EMIF will put the
DDR in self refresh mode to save power if EMIF_PWR_MGMT_CTRL register
is pro

ARM: DRA7: DDR: Enable SR in Power Management Control

If EMIF is idle for certain amount of DDR cycles, EMIF will put the
DDR in self refresh mode to save power if EMIF_PWR_MGMT_CTRL register
is programmed. And also before entering suspend-resume ddr needs to
be put in self-refresh. Linux kernel does not program this register
before entering suspend and relies on u-boot setting.
So configuring it in u-boot.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: DRA7: emif: Enable interleaving for higher address space

Given that DRA7/OMAP5 SoCs can support more than 2GB of memory,
enable interleaving for this higher memory to increase performance.

Sig

ARM: DRA7: emif: Enable interleaving for higher address space

Given that DRA7/OMAP5 SoCs can support more than 2GB of memory,
enable interleaving for this higher memory to increase performance.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: DRA7: emif: Check for enable bits before updating leveling output

Read and write leveling can be enabled independently. Check for these
enable bits before updating the read and write leveling o

ARM: DRA7: emif: Check for enable bits before updating leveling output

Read and write leveling can be enabled independently. Check for these
enable bits before updating the read and write leveling output values.
This will allow to use the combination of software and hardware leveling.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Merge branch 'u-boot/master' into 'u-boot-arm/master'

am33xx: Re-enable SW levelling for DDR2

The recent changes for hw leveling on am33xx were not intended for
DDR2 boards, only DDR3. Update emif_sdram_type to take a sdram_config
value to check agains

am33xx: Re-enable SW levelling for DDR2

The recent changes for hw leveling on am33xx were not intended for
DDR2 boards, only DDR3. Update emif_sdram_type to take a sdram_config
value to check against. This lets us pass in the value we would use to
configure, when we have not yet configured the board yet. In other cases
update the call to be as functional as before and check an already
programmed value in.

Tested-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

ARM: DRA7: DDR3: Add support for HW leveling

DRA7 EMIF supports Full leveling for DDR3.
Adding support for the Full leveling sequence.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by:

ARM: DRA7: DDR3: Add support for HW leveling

DRA7 EMIF supports Full leveling for DDR3.
Adding support for the Full leveling sequence.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Merge remote-tracking branch 'u-boot/master' into 'u-boot-arm/master'

ARM: DRA7: EMIF: Update SDRAM_REF_CTRL register value

The value in SDRAM_REF_CTRL controls the delay time between
the initial rising edge of DDR_RESETn to rising edge of DDR_CKE
(JEDEC specs this as

ARM: DRA7: EMIF: Update SDRAM_REF_CTRL register value

The value in SDRAM_REF_CTRL controls the delay time between
the initial rising edge of DDR_RESETn to rising edge of DDR_CKE
(JEDEC specs this as 500us). In order to achieve this, SDRAM_REF_CTRL
should be written with a value corresponding to 500us delay before
starting DDR initialization sequence, and configure proper
value at the end of sequence.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-ti

arm: am437x: Enable hardware leveling for EMIF

Switch to using hardware leveling for certain parameters on the EMIF
rather than using precalculated values. Doing this also means we have a
common pl

arm: am437x: Enable hardware leveling for EMIF

Switch to using hardware leveling for certain parameters on the EMIF
rather than using precalculated values. Doing this also means we have a
common place now between am437x and am335x for setting
emif_sdram_ref_ctrl with a value for the correct delay length.

Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

show more ...

emif.h: remove duplicated argument to |

Remove the duplicated argument to | in two places. Reported
by Coccinelle (http://coccinelle.lip6.fr/).

Signed-off-by: Maxin B. John <maxin.john@enea.com>

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Conflicts:
boards.cfg

am43xx: Tune the system to avoid DSS underflows

* This is done by limiting the ARM's bandwidth and setting DSS priority in
the EMIF controller to ensure underflows do not occur.

Merge branch 'master' of git://git.denx.de/u-boot-arm

Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.

Conflicts:
include/configs/ex

Merge branch 'master' of git://git.denx.de/u-boot-arm

Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.

Conflicts:
include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini <trini@ti.com>

show more ...

ARM: AM43xx: GP_EVM: Add support for DDR3

GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enab

ARM: AM43xx: GP_EVM: Add support for DDR3

GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

ARM: AM43xx: EPOS_EVM: Add support for LPDDR2

AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief descr

ARM: AM43xx: EPOS_EVM: Add support for LPDDR2

AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:
board/samsung/trats2/trats2.c
include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini <trini@ti.com>

Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

ARM: DRA7/OMAP5: EMIF: Add workaround for bug 0039

When core power domain hits oswr, then DDR3 memories does not come back
while resuming. This is because when EMIF registers are lost, then the
cont

ARM: DRA7/OMAP5: EMIF: Add workaround for bug 0039

When core power domain hits oswr, then DDR3 memories does not come back
while resuming. This is because when EMIF registers are lost, then the
controller takes care of copying the values from the shadow registers.
If the shadow registers are not updated with the right values, then this
results in incorrect settings while resuming. So updating the shadow registers
with the corresponding status registers here during the boot.

Signed-off-by: Sricharan R <r.sricharan@ti.com>

show more ...

ARM: DRA: EMIF: Change DDR3 settings to use hw leveling

Currently the DDR3 memory on DRA7 ES1.0 evm board is enabled using
software leveling. This was done since hardware leveling was not
working. N

ARM: DRA: EMIF: Change DDR3 settings to use hw leveling

Currently the DDR3 memory on DRA7 ES1.0 evm board is enabled using
software leveling. This was done since hardware leveling was not
working. Now that the right sequence to do hw leveling is identified,
use it. This is required for EMIF clockdomain to idle and come back
during lowpower usecases.

Signed-off-by: Sricharan R <r.sricharan@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR

Conflicts:
arch/arm/include/asm/arch-omap5/omap.h

Signed-off-by: Tom Ri

Merge branch 'master' of git://git.denx.de/u-boot-arm

Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR

Conflicts:
arch/arm/include/asm/arch-omap5/omap.h

Signed-off-by: Tom Rini <trini@ti.com>

show more ...