tools: mkimage: add support for Vybrid image format

This format can be flashed directly at address 0 of
the NAND FLASH, as it contains all necessary headers.

Signed-off-by: Albert ARIBAUD (3ADEV) <

tools: mkimage: add support for Vybrid image format

This format can be flashed directly at address 0 of
the NAND FLASH, as it contains all necessary headers.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>

show more ...

imx: imx6ul: disable POR_B internal pull up

>From TO1.1, SNVS adds internal pull up control for POR_B,
the register filed is GPBIT[1:0], after system boot up,
it can be set to 2b'01 to disable inter

imx: imx6ul: disable POR_B internal pull up

>From TO1.1, SNVS adds internal pull up control for POR_B,
the register filed is GPBIT[1:0], after system boot up,
it can be set to 2b'01 to disable internal pull up.
It can save about 30uA power in SNVS mode.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

imx: mx6: fix USB bmode to use reserved value

Currently the bmode "usb" uses BOOT_CFG1 to 0x01, -which means
BOOT_CFG1[7:4] is set to b0000. According to Table 8-7 Boot
Device Selection this is NOR/

imx: mx6: fix USB bmode to use reserved value

Currently the bmode "usb" uses BOOT_CFG1 to 0x01, -which means
BOOT_CFG1[7:4] is set to b0000. According to Table 8-7 Boot
Device Selection this is NOR/OneNAND and not Reserved.

Use 0x10 which leads to b0001, which is a Reserved boot device.
With that the SoC reliably falls back to the serial loader.

Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>

show more ...

arm: imx: add i.MX6ULL 14x14 EVK board support

Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
T

arm: imx: add i.MX6ULL 14x14 EVK board support

Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.

Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)

CPU: Freescale i.MX6ULL rev1.0 at 396MHz
CPU: Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM: 512 MiB
MMC: initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

imx: imx6ull: adjust the ldo 1.2v bandgap voltage

Per to design team, on i.MX6UL, the LDO 1.2V bandgap voltage
is 30mV higher, so we need to adjust the REFTOP_VBGADJ(anatop
MISC0 bit[6:4]) setting t

imx: imx6ull: adjust the ldo 1.2v bandgap voltage

Per to design team, on i.MX6UL, the LDO 1.2V bandgap voltage
is 30mV higher, so we need to adjust the REFTOP_VBGADJ(anatop
MISC0 bit[6:4]) setting to 2b'110.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

imx: mx6ull: update clock settings and CCM register map

Update Clock settings and CCM register map for i.MX6ULL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc:

imx: mx6ull: update clock settings and CCM register map

Update Clock settings and CCM register map for i.MX6ULL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

imx: mx6ull: adjust POR_B setting for i.MX6ULL

Adjust POR_B settings on i.MX6ULL according to IC design
team's suggestion:

2'b00 : always PUP100K
2'b01 : PUP100K when PMIC_ON_REQ || SOC_NOT_FAIL

imx: mx6ull: adjust POR_B setting for i.MX6ULL

Adjust POR_B settings on i.MX6ULL according to IC design
team's suggestion:

2'b00 : always PUP100K
2'b01 : PUP100K when PMIC_ON_REQ || SOC_NOT_FAIL
2'b10 : always disable PUP100K
2'b11 : PDN100K when SOC_FAIL, PUP100K when SOC_NOT_FAIL -- recommended setting

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

imx: mx6ull: misc soc update

Update misc SOC related settings for i.MX6ULL, such as FEC mac address,
cpu speed grading and mmdc channel mask clearing.

Also update s_init to skip pfd reset.

Signed-

imx: mx6ull: misc soc update

Update misc SOC related settings for i.MX6ULL, such as FEC mac address,
cpu speed grading and mmdc channel mask clearing.

Also update s_init to skip pfd reset.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

imx: mx6ul: using runtime check when configuring PMIC_STBY_REQ

Since MX6ULL select MX6UL, we can not use IS_ENABLED(CONFIG_MX6UL) here,
because this piece code is only for i.MX6UL.

Signed-off-by: P

imx: mx6ul: using runtime check when configuring PMIC_STBY_REQ

Since MX6ULL select MX6UL, we can not use IS_ENABLED(CONFIG_MX6UL) here,
because this piece code is only for i.MX6UL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>

show more ...

imx: mx6ull: skip setting ahb clock

Rom already initialized clock at 396M and 132M for arm core and ahb,
so skip setting them again in U-Boot.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano

imx: mx6ull: skip setting ahb clock

Rom already initialized clock at 396M and 132M for arm core and ahb,
so skip setting them again in U-Boot.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>

show more ...

imx: mx6ull: add kconfig entry for MX6ULL

i.MX6ULL is derivative from i.MX6UL, so select MX6UL for MX6ULL.
If need to differenate MX6ULL from MX6UL, use CONFIG_MX6ULL

Signed-off-by: Peng Fan <peng.

imx: mx6ull: add kconfig entry for MX6ULL

i.MX6ULL is derivative from i.MX6UL, so select MX6UL for MX6ULL.
If need to differenate MX6ULL from MX6UL, use CONFIG_MX6ULL

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

ti: omap-common: Allow AM33xx devices to be built securely

Like OMAP54xx and AM43xx family SoCs, AM33xx based SoCs have high
security enabled models. Allow AM33xx devices to be built with
HS Device

ti: omap-common: Allow AM33xx devices to be built securely

Like OMAP54xx and AM43xx family SoCs, AM33xx based SoCs have high
security enabled models. Allow AM33xx devices to be built with
HS Device Type Support.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

am33xx: config.mk: Fix option used to enable SPI SPL image type

The option SPL_SPI_SUPPORT is used to enable support in SPL for loading
images from SPI flash, it should not be used to determine the

am33xx: config.mk: Fix option used to enable SPI SPL image type

The option SPL_SPI_SUPPORT is used to enable support in SPL for loading
images from SPI flash, it should not be used to determine the build type
of the SPL image itself. The ability to read images from SPI flash does
not imply the SPL will be booted from SPI flash.

Unconditionally build SPI flash compatible SPL images.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

am33xx: config.mk: Add support for additional secure boot image types

Depending on the boot media, different images are needed
for secure devices. The build generates u-boot*_HS_* files
as appropria

am33xx: config.mk: Add support for additional secure boot image types

Depending on the boot media, different images are needed
for secure devices. The build generates u-boot*_HS_* files
as appropriate for the different boot modes.

For AM33xx devices additional image types are needed for
various SPL boot modes as the ROM checks for the name of
the boot mode in the file it loads.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>

show more ...

Kconfig: Separate AM33XX SOC config from target board config

The config option AM33XX is used in several boards and should be
defined as a stand-alone option for this SOC. We break this out
from tar

Kconfig: Separate AM33XX SOC config from target board config

The config option AM33XX is used in several boards and should be
defined as a stand-alone option for this SOC. We break this out
from target boards that use this SoC and common headers then enable
AM33XX on in all the boards that used these targets to eliminate any
functional change with this patch.

This is similar to what has already been done in
9de852642cae ("arm: Kconfig: Add support for AM43xx SoC specific Kconfig")
and is done for the same reasons.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: omap5: add fdt secure dram reservation fixup

Adds a secure dram reservation fixup for secure
devices, when a region in the emif has been set aside
for secure world use. The size is defined by t

ARM: omap5: add fdt secure dram reservation fixup

Adds a secure dram reservation fixup for secure
devices, when a region in the emif has been set aside
for secure world use. The size is defined by the
CONFIG_TI_SECURE_EMIF_TOTAL_REGION_SIZE config option.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: DRA7: Add secure emif setup calls

After EMIF DRAM is configured, but before it is used,
calls are made on secure devices to reserve any configured
memory region needed by the secure world and t

ARM: DRA7: Add secure emif setup calls

After EMIF DRAM is configured, but before it is used,
calls are made on secure devices to reserve any configured
memory region needed by the secure world and then to lock the
EMIF firewall configuration. If any other firewall
configuration needs to be applied, it must happen before the
lock call.

Signed-off-by: Daniel Allred <d-allred@ti.com>

show more ...

arm: omap5: secure API for EMIF memory reservations

Create a few public APIs which rely on secure world ROM/HAL
APIs for their implementation. These are intended to be used
to reserve a portion of t

arm: omap5: secure API for EMIF memory reservations

Create a few public APIs which rely on secure world ROM/HAL
APIs for their implementation. These are intended to be used
to reserve a portion of the EMIF memory and configure hardware
firewalls around that region to prevent public code from
manipulating or interfering with that memory.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ti: omap5: Add Kconfig options for secure EMIF reservations

Adds start address and size config options for setting aside
a portion of the EMIF memory space for usage by security software
(like a sec

ti: omap5: Add Kconfig options for secure EMIF reservations

Adds start address and size config options for setting aside
a portion of the EMIF memory space for usage by security software
(like a secure OS/TEE). There are two sizes, a total size and a
protected size. The region is divided into protected (secure) and
unprotected (public) regions, that are contiguous and start at the
start address given. If the start address is zero, the intention
is that the region will be automatically placed at the end of the
available external DRAM space.

Signed-off-by: Daniel Allred <d-allred@ti.com>

show more ...

dra7x: boot: add dfu bootmode support

This patch enables the DFU boot mode support
for dra7x platform.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Merge git://git.denx.de/u-boot-fsl-qoriq

trini: Drop local memset() from
examples/standalone/mem_to_mem_idma2intr.c

Signed-off-by: Tom Rini <trini@konsulko.com>

armv7: ls102xa: Rename GIC_ADDR and DCSR_RCPM_ADDR

Instead of using CONFIG_* name space, rename these two macros to
SYS_FSL_* space.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hon

armv7: ls102xa: Rename GIC_ADDR and DCSR_RCPM_ADDR

Instead of using CONFIG_* name space, rename these two macros to
SYS_FSL_* space.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

armv7: ls1021a: Convert CONFIG_LS1_DEEP_SLEEP to Kconfig option

Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp

armv7: ls1021a: Convert CONFIG_LS1_DEEP_SLEEP to Kconfig option

Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

Convert CONFIG_SYS_FSL_ERRATUM_A010315 to Kconfig option

Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>

armv8: ls1012a: Convert CONFIG_LS1012A to Kconfig option ARCH_LS1021A

Move this config to Kconfig option and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Calvin Johnson <c

armv8: ls1012a: Convert CONFIG_LS1012A to Kconfig option ARCH_LS1021A

Move this config to Kconfig option and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Calvin Johnson <calvin.johnson@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...