env: Rename getenv/_f() to env_get()

We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few place

env: Rename getenv/_f() to env_get()

We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

Merge git://git.denx.de/u-boot-dm

dm: scsi: Document and rename the scsi_scan() parameter

The 'mode' parameter is actually a flag to determine whether to display
a list of devices found during the scan. Rename it to reflect this, ad

dm: scsi: Document and rename the scsi_scan() parameter

The 'mode' parameter is actually a flag to determine whether to display
a list of devices found during the scan. Rename it to reflect this, add a
function comment and adjust callers to use a boolean.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

show more ...

Merge git://git.denx.de/u-boot-fsl-qoriq

armv8: layerscape: Make U-Boot EL2 safe

When U-Boot boots from EL2, skip some lowlevel init code requiring
EL3, including CCI-400/CCN-504, trust zone, GIC, etc. These
initialization tasks are carrie

armv8: layerscape: Make U-Boot EL2 safe

When U-Boot boots from EL2, skip some lowlevel init code requiring
EL3, including CCI-400/CCN-504, trust zone, GIC, etc. These
initialization tasks are carried out before U-Boot runs. This applies
to the RAM version image used for SPL boot if PPA is loaded first.

Signed-off-by: York Sun <york.sun@nxp.com>

show more ...

armv8: ls2080a: Reorganise NAND_BOOT code in config flag

Add CONFIG_NAND_BOOT config flag to organise
NAND_BOOT specific code in config flag like
-nand-boot specfic errata errata_rcw_src()
-CONFIG_S

armv8: ls2080a: Reorganise NAND_BOOT code in config flag

Add CONFIG_NAND_BOOT config flag to organise
NAND_BOOT specific code in config flag like
-nand-boot specfic errata errata_rcw_src()
-CONFIG_SYS_NAND_U_BOOT_DST,etc

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

Merge git://git.denx.de/u-boot-fsl-qoriq

armv8: fsl-lsch3: Conditionally apply workaround for erratum a0009203

This i2c errata only applies to LS2080A and its variants, namely
LS2080A, LS2085A and LS2088A.

Signed-off-by: Ashish Kumar <Ash

armv8: fsl-lsch3: Conditionally apply workaround for erratum a0009203

This i2c errata only applies to LS2080A and its variants, namely
LS2080A, LS2085A and LS2088A.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

Merge git://git.denx.de/u-boot-fsl-qoriq

armv8: fsl-lsch2: add workaround for erratum A-010635

Read DMA operations causes CRC error on armv8 chassis 2 platforms
due to the erratum A-010635.
In order to support sata on these platforms, ECC

armv8: fsl-lsch2: add workaround for erratum A-010635

Read DMA operations causes CRC error on armv8 chassis 2 platforms
due to the erratum A-010635.
In order to support sata on these platforms, ECC needs to be disabled.

Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

Merge git://git.denx.de/u-boot-fsl-qoriq

armv8: fsl-lsch3: enable snoopable sata read and write

By default the SATA IP on the ls208Xa SoCs does not generating
coherent/snoopable transactions. This patch enable it in the
sata axicc registe

armv8: fsl-lsch3: enable snoopable sata read and write

By default the SATA IP on the ls208Xa SoCs does not generating
coherent/snoopable transactions. This patch enable it in the
sata axicc register.

Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

armv8/fsl_lsch2: Add chip power supply voltage setup

Set up chip power supply voltage according to voltage ID.
The fuse status register provides the values from on-chip
voltage ID fuses programmed a

armv8/fsl_lsch2: Add chip power supply voltage setup

Set up chip power supply voltage according to voltage ID.
The fuse status register provides the values from on-chip
voltage ID fuses programmed at the factory. These values
define the voltage requirements for the chip.

Main operations:
1. Set up the core voltage
2. Set up the SERDES voltage and reset SERDES lanes
3. Enable/disable DDR controller support 0.9V if needed

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Merge git://git.denx.de/u-boot-fsl-qoriq

armv8: QSPI: Add AHB bus 16MB+ size support

The default configuration for QSPI AHB bus can't support 16MB+.
But some flash on NXP layerscape board are more than 16MB.

Signed-off-by: Yuan Yao <yao.y

armv8: QSPI: Add AHB bus 16MB+ size support

The default configuration for QSPI AHB bus can't support 16MB+.
But some flash on NXP layerscape board are more than 16MB.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge git://git.denx.de/u-boot-fsl-qoriq

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
arch/arm/Kconfig

armv8: fsl-layerscape: Add NXP LS2088A SoC support

The QorIQ LS2088A SoC is built on layerscape architecture.

It is similar to LS2080A SoC with some differences like
1)Timer controller offset is di

armv8: fsl-layerscape: Add NXP LS2088A SoC support

The QorIQ LS2088A SoC is built on layerscape architecture.

It is similar to LS2080A SoC with some differences like
1)Timer controller offset is different
2)It has A72 cores
3)It supports TZASC module

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

armv8/fsl-layerscape: Update CONFIG_LS2080A to CONFIG_FSL_LSCH3

Update CONFIG_LS2080A to CONFIG_FSL_LSCH3 to make those workaround
implementing of erratum reusable for more SoCs.

Signed-off-by: She

armv8/fsl-layerscape: Update CONFIG_LS2080A to CONFIG_FSL_LSCH3

Update CONFIG_LS2080A to CONFIG_FSL_LSCH3 to make those workaround
implementing of erratum reusable for more SoCs.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

Merge git://git.denx.de/u-boot-fsl-qoriq

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
include/configs/ls1021aqds.h
include/configs/ls1021atwr.h

armv8/fsl-lsch2: Implement workaround for PIN MUX erratum A010539

Pin mux logic has 2 options in priority order, one is through RCW_SRC
and then through RCW_Fields. In case of QSPI booting, RCW_SRC

armv8/fsl-lsch2: Implement workaround for PIN MUX erratum A010539

Pin mux logic has 2 options in priority order, one is through RCW_SRC
and then through RCW_Fields. In case of QSPI booting, RCW_SRC logic
takes the priority for SPI pads and do not allow RCW_BASE and SPI_EXT
to control the SPI muxing. But actually those are DSPI controller's
pads instead of QSPI controller's, so this workaround allows RCW
fields SPI_BASE and SPI_EXT to control relevant pads muxing.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[York Sun: Reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

armv8: fsl-lsch2: enable snoopable sata read and write

By default the SATA IP on the ls1043a/ls1046a SoCs does not
generating coherent/snoopable transactions. This patch enable
it in the SCFG_SNPCN

armv8: fsl-lsch2: enable snoopable sata read and write

By default the SATA IP on the ls1043a/ls1046a SoCs does not
generating coherent/snoopable transactions. This patch enable
it in the SCFG_SNPCNFGCR register along with sata axicc register.
In addition, the dma-coherent property must be set on the SATA
controller nodes.

Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
[York Sun: Reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

armv8: fsl-lsch2: adjust sata parameter

The default values for Port Phy2Cfg register and
Port Phy3Cfg register are better, no need to overwrite them.

Signed-off-by: Tang Yuantian <yuantian.tang@nxp

armv8: fsl-lsch2: adjust sata parameter

The default values for Port Phy2Cfg register and
Port Phy3Cfg register are better, no need to overwrite them.

Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

Merge git://git.denx.de/u-boot-fsl-qoriq

trini: Drop local memset() from
examples/standalone/mem_to_mem_idma2intr.c

Signed-off-by: Tom Rini <trini@konsulko.com>