Optimize Cortex-A57 cluster power down sequence on Juno

This patch optimizes the Cortex-A57 cluster power down sequence by not
flushing the Level1 data cache. The L1 data cache and the L2 unified
ca

Optimize Cortex-A57 cluster power down sequence on Juno

This patch optimizes the Cortex-A57 cluster power down sequence by not
flushing the Level1 data cache. The L1 data cache and the L2 unified
cache are inclusive. A flush of the L2 by set/way flushes any dirty
lines from the L1 as well. This is a known safe deviation from the
Cortex-A57 TRM defined power down sequence. This optimization can be
enabled by the platform through the 'SKIP_A57_L1_FLUSH_PWR_DWN' build
flag. Each Cortex-A57 based platform must make its own decision on
whether to use the optimization.

This patch also renames the cpu-errata-workarounds.md to
cpu-specific-build-macros.md as this facilitates documentation
of both CPU Specific errata and CPU Specific Optimization
build macros.

Change-Id: I299b9fe79e9a7e08e8a0dffb7d345f9a00a71480

show more ...

Optimize barrier usage during Cortex-A57 power down

This the patch replaces the DSB SY with DSB ISH
after disabling L2 prefetches during the Cortex-A57
power down sequence.

Change-Id: I048d12d830c1

Optimize barrier usage during Cortex-A57 power down

This the patch replaces the DSB SY with DSB ISH
after disabling L2 prefetches during the Cortex-A57
power down sequence.

Change-Id: I048d12d830c1b974b161224eff079fb9f8ecf52d

show more ...

Apply errata workarounds only when major/minor revisions match.

Prior to this patch, the errata workarounds were applied for any version
of the CPU in the release build and in the debug build an ass

Apply errata workarounds only when major/minor revisions match.

Prior to this patch, the errata workarounds were applied for any version
of the CPU in the release build and in the debug build an assert
failure resulted when the revision did not match. This patch applies
errata workarounds in the Cortex-A57 reset handler only if the 'variant'
and 'revision' fields read from the MIDR_EL1 match. In the debug build,
a warning message is printed for each errata workaround which is not
applied.

The patch modifies the register usage in 'reset_handler` so
as to adhere to ARM procedure calling standards.

Fixes ARM-software/tf-issues#242

Change-Id: I51b1f876474599db885afa03346e38a476f84c29

show more ...

Add support for level specific cache maintenance operations

This patch adds level specific cache maintenance functions
to cache_helpers.S. The new functions 'dcsw_op_levelx',
where '1 <= x <= 3', al

Add support for level specific cache maintenance operations

This patch adds level specific cache maintenance functions
to cache_helpers.S. The new functions 'dcsw_op_levelx',
where '1 <= x <= 3', allow to perform cache maintenance by
set/way for that particular level of cache. With this patch,
functions to support cache maintenance upto level 3 have
been implemented since it is the highest cache level for
most ARM SoCs.

These functions are now utilized in CPU specific power down
sequences to implement them as mandated by processor specific
technical reference manual.

Change-Id: Icd90ce6b51cff5a12863bcda01b93601417fd45c

show more ...

Merge pull request #217 from jcastillo-arm/jc/tf-issues/257

FVP: keep shared data in Trusted SRAM

Merge pull request #216 from vikramkanigiri/vk/juno_standby_support

Juno: Support entry into a standby state

Merge pull request #215 from jcastillo-arm/jc/juno_mem_6

Jc/juno mem 6

FVP: keep shared data in Trusted SRAM

This patch deprecates the build option to relocate the shared data
into Trusted DRAM in FVP. After this change, shared data is always
located at the base of Tru

FVP: keep shared data in Trusted SRAM

This patch deprecates the build option to relocate the shared data
into Trusted DRAM in FVP. After this change, shared data is always
located at the base of Trusted SRAM. This reduces the complexity
of the memory map and the number of combinations in the build
options.

Fixes ARM-software/tf-issues#257

Change-Id: I68426472567b9d8c6d22d8884cb816f6b61bcbd3

show more ...

Juno: Support entry into a standby state

This patch adds support on the Juno platform for entering a wfi in
response to a PSCI CPU_SUSPEND call where the state type is a
standby state.

Change-Id: I

Juno: Support entry into a standby state

This patch adds support on the Juno platform for entering a wfi in
response to a PSCI CPU_SUSPEND call where the state type is a
standby state.

Change-Id: I0a102dee1f8d2ad936c63ad1d1d3ad001a4a4768

show more ...

Juno: Reserve some DDR-DRAM for secure use

This patch configures the TrustZone Controller in Juno to split
the 2GB DDR-DRAM memory at 0x80000000 into Secure and Non-Secure
regions:

- Secure DDR-DRA

Juno: Reserve some DDR-DRAM for secure use

This patch configures the TrustZone Controller in Juno to split
the 2GB DDR-DRAM memory at 0x80000000 into Secure and Non-Secure
regions:

- Secure DDR-DRAM: top 16 MB, except for the last 2 MB which are
used by the SCP for DDR retraining
- Non-Secure DDR-DRAM: remaining DRAM starting at base address

Build option PLAT_TSP_LOCATION selects the location of the secure
payload (BL3-2):

- 'tsram' : Trusted SRAM (default option)
- 'dram' : Secure region in the DDR-DRAM (set by the TrustZone
controller)

The MMU memory map has been updated to give BL2 permission to load
BL3-2 into the DDR-DRAM secure region.

Fixes ARM-software/tf-issues#233

Change-Id: I6843fc32ef90aadd3ea6ac4c7f314f8ecbd5d07b

show more ...

Merge pull request #206 from soby-mathew/sm/reset_cntvoff

Reset CNTVOFF_EL2 register before exit into EL1 on warm boot

Juno: Use TZC-400 driver calls

This patch replaces direct accesses to the TZC-400 registers by the
appropiate calls to the generic driver available in the Trusted
Firmware in order to initialize the

Juno: Use TZC-400 driver calls

This patch replaces direct accesses to the TZC-400 registers by the
appropiate calls to the generic driver available in the Trusted
Firmware in order to initialize the TrustZone Controller.

Functions related to the initialization of the secure memory,
like the TZC-400 configuration, have been moved to a new file
'plat_security.c'. This reorganization makes easier to set up
the secure memory from any BL stage.

TZC-400 initialization has been moved from BL1 to BL2 because BL1
does not access the non-secure memory. It is BL2's responsibility
to enable and configure the TZC-400 before loading the next BL
images.

In Juno, BL3-0 initializes some of the platform peripherals, like
the DDR controller. Thus, BL3-0 must be loaded before configuring
the TrustZone Controller. As a consequence, the IO layer
initialization has been moved to early platform initialization.

Fixes ARM-software/tf-issues#234

Change-Id: I83dde778f937ac8d2996f7377e871a2e77d9490e

show more ...

Merge pull request #214 from soby-mathew/sm/bl_specific_mmap

Create BL stage specific translation tables

Create BL stage specific translation tables

This patch uses the IMAGE_BL<x> constants to create translation tables specific
to a boot loader stage. This allows each stage to create mappings only for

Create BL stage specific translation tables

This patch uses the IMAGE_BL<x> constants to create translation tables specific
to a boot loader stage. This allows each stage to create mappings only for areas
in the memory map that it needs.

Fixes ARM-software/tf-issues#209

Change-Id: Ie4861407ddf9317f0fb890fc7575eaa88d0de51c

show more ...

Merge pull request #213 from soby-mathew/sm/crash_reporting_fix

Remove BSS section access by 'plat_print_gic' during crash reporting

Remove BSS section access by 'plat_print_gic' during crash reporting

This patch avoids the problem of crash reporting mechanism accessing
global data in BSS by 'plat_print_gic_regs' for FVP platform

Remove BSS section access by 'plat_print_gic' during crash reporting

This patch avoids the problem of crash reporting mechanism accessing
global data in BSS by 'plat_print_gic_regs' for FVP platforms. Earlier
it depended on the global 'plat_config' object for the GIC Base address
in FVP platforms which would have caused exception if it were accessed
before the BSS was initialized. It is now fixed by dynamically
querying the V2M_SYS_ID to find the FVP model type and accordingly
selecting the appropriate GIC Base address.

This patch also fixes the 'plat_print_gic_regs' to use the correct GIC
Distributor base address for printing GICD_IS_PENDR register values
for both Juno and FVP platforms.

Fixes ARM-Software/tf-issues#236

Change-Id: I545c7b908b3111419bf27db0575ce86acf86784b

show more ...

Merge pull request #212 from jcastillo-arm/jc/tf-issues/252

Fix LENGTH attribute value in linker scripts

Fix LENGTH attribute value in linker scripts

This patch fixes the incorrect value of the LENGTH attribute in
the linker scripts. This attribute must define the memory size, not
the limit address.

F

Fix LENGTH attribute value in linker scripts

This patch fixes the incorrect value of the LENGTH attribute in
the linker scripts. This attribute must define the memory size, not
the limit address.

Fixes ARM-software/tf-issues#252

Change-Id: I328c38b9ec502debe12046a8912d7dfc54610c46

show more ...

Merge pull request #211 from jenswi-linaro/optee_140916

Dispatcher for OPTEE from Linaro SWG

Add opteed based on tspd

Adds a dispatcher for OP-TEE based on the test secure payload
dispatcher.

Fixes arm-software/tf-issues#239

Initialize SCTLR_EL1 based on MODE_RW bit

Initializes SCTLR_EL1 based on MODE_RW bit in SPSR for the entry
point. The RES1 bits for SCTLR_EL1 differs for Aarch64 and Aarch32
mode.

Merge pull request #210 from soby-mathew/sm/makefile_bl_stages

Add support for specifying pre-built BL binaries in Makefile

Add support for specifying pre-built BL binaries in Makefile

This patch adds support for supplying pre-built BL binaries for BL2,
BL3-1 and BL3-2 during trusted firmware build. Specifying BLx = <pat

Add support for specifying pre-built BL binaries in Makefile

This patch adds support for supplying pre-built BL binaries for BL2,
BL3-1 and BL3-2 during trusted firmware build. Specifying BLx = <path_to_BLx>
in the build command line, where 'x' is any one of BL2, BL3-1 or BL3-2, will
skip building that BL stage from source and include the specified binary in
final fip image.

This patch also makes BL3-3 binary for FIP optional depending on the
value of 'NEED_BL33' flag which is defined by the platform.

Fixes ARM-software/tf-issues#244
Fixes ARM-software/tf-issues#245

Change-Id: I3ebe1d4901f8b857e8bb51372290978a3323bfe7

show more ...

Reset CNTVOFF_EL2 register before exit into EL1 on warm boot

This patch resets the value of CNTVOFF_EL2 before exit to EL1 on
warm boot. This needs to be done if only the Trusted Firmware exits
to E

Reset CNTVOFF_EL2 register before exit into EL1 on warm boot

This patch resets the value of CNTVOFF_EL2 before exit to EL1 on
warm boot. This needs to be done if only the Trusted Firmware exits
to EL1 instead of EL2, otherwise the hypervisor would be responsible
for this.

Fixes ARM-software/tf-issues#240

Change-Id: I79d54831356cf3215bcf1f251c373bd8f89db0e0

show more ...

Merge pull request #205 from danh-arm/dh/1.0-docs

Documentation for version 1.0