Merge "feat(stm32mp15): remove OP-TEE shared mem" into integration

feat(stm32mp15): remove OP-TEE shared mem

The flag STM32MP15_OPTEE_RSV_SHM was disabled and mark deprecated.
Remove the corresponding code.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-

feat(stm32mp15): remove OP-TEE shared mem

The flag STM32MP15_OPTEE_RSV_SHM was disabled and mark deprecated.
Remove the corresponding code.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I948af3e1de4b89815c967a63abe64f285c405ecc

show more ...

Merge changes from topic "stm32mp2" into integration

* changes:
feat(stm32mp2): generate stm32 file
feat(stm32mp2-fdts): add stm32mp257f-ev1 board
feat(stm32mp2-fdts): introduce stm32mp25 pinc

Merge changes from topic "stm32mp2" into integration

* changes:
feat(stm32mp2): generate stm32 file
feat(stm32mp2-fdts): add stm32mp257f-ev1 board
feat(stm32mp2-fdts): introduce stm32mp25 pinctrl files
feat(stm32mp2-fdts): introduce stm32mp25 SoCs family
feat(stm32mp2): add console configuration
feat(st): add RCC registers list
feat(st-uart): add AARCH64 stm32_console driver
feat(st): introduce new platform STM32MP2
feat(dt-bindings): add the STM32MP2 clock and reset bindings
docs(changelog): add scopes for STM32MP2
feat(docs): introduce STM32MP2 doc
refactor(docs): add a sub-menu for ST platforms
refactor(st): move plat_image_load.c
refactor(st): rename PLAT_NB_FIXED_REGS
refactor(st): move some storage definitions to common part
refactor(st): move SDMMC definitions to driver
feat(st-clock): stub fdt_get_rcc_secure_state
feat(st-clock): allow aarch64 compilation of STGEN functions
feat(st): allow AARCH64 compilation for common code
refactor(st): rename QSPI macros

show more ...

refactor(st): move some storage definitions to common part

Those storage macros are common to all STM32MPU chips, move them to
plat/st/common/include/stm32mp_io_storage.h

Signed-off-by: Yann Gautie

refactor(st): move some storage definitions to common part

Those storage macros are common to all STM32MPU chips, move them to
plat/st/common/include/stm32mp_io_storage.h

Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Id20ec00ba65edf9ec7a3a89adfda307c954c3cb6

show more ...

Merge "feat(stm32mp1): add FWU with boot from NOR-SPI" into integration

feat(stm32mp1): add FWU with boot from NOR-SPI

Refactor the SDCARD/EMMC FWU, to add the NOR-SPI use case.
SPI-NOR FWU won't use a real partition uuid to find the correct FIP,
but the UUID from metad

feat(stm32mp1): add FWU with boot from NOR-SPI

Refactor the SDCARD/EMMC FWU, to add the NOR-SPI use case.
SPI-NOR FWU won't use a real partition uuid to find the correct FIP,
but the UUID from metadata will correspond with a hardcoded offset in
the NOR.
While at it change some __unused keywords to __maybe_unused to ease
checkpatch.pl analysis.

Signed-off-by: Frank Bodammer <frank.bodammer@siemens.com>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I2fe56ba8534a3c5dfaf8aeb16e7b286909883cc2

show more ...

Merge changes from topic "stm32mp1-trusted-boot" into integration

* changes:
docs(st): update documentation for TRUSTED_BOARD_BOOT
fix(build): ensure that the correct rule is called for tools

Merge changes from topic "stm32mp1-trusted-boot" into integration

* changes:
docs(st): update documentation for TRUSTED_BOARD_BOOT
fix(build): ensure that the correct rule is called for tools
feat(stm32mp1): add the platform specific build for tools
fix(stm32mp13-fdts): remove secure status
feat(stm32mp1-fdts): add CoT and fuse references for authentication
feat(stm32mp1): add a check on TRUSTED_BOARD_BOOT with secure chip
feat(stm32mp1): add the decryption support
feat(stm32mp1): add the TRUSTED_BOARD_BOOT support
feat(stm32mp1): update ROM code API for header v2 management
feat(stm32mp1): remove unused function from boot API
refactor(stm32mp1): remove authentication using STM32 image mode
fix(fconf): fix type error displaying disable_auth
feat(tbbr): increase PK_DER_LEN size
fix(auth): correct sign-compare warning
feat(auth): allow to verify PublicKey with platform format PK
feat(cert-create): update for ECDSA brainpoolP256r/t1 support
feat(stm32mp1): add RNG initialization in BL2 for STM32MP13
feat(st-crypto): remove BL32 HASH driver usage
feat(stm32mp1): add a stm32mp crypto library
feat(st-crypto): add STM32 RNG driver
feat(st-crypto): add AES decrypt/auth by SAES IP
feat(st-crypto): add ECDSA signature check with PKA
feat(st-crypto): update HASH for new hardware version used in STM32MP13

show more ...

feat(stm32mp1): add the TRUSTED_BOARD_BOOT support

Add the support of the TRUSTED_BOARD_BOOT to authenticate the loaded
FIP using platform CoT management.
It adds TBB platform definition, redefining

feat(stm32mp1): add the TRUSTED_BOARD_BOOT support

Add the support of the TRUSTED_BOARD_BOOT to authenticate the loaded
FIP using platform CoT management.
It adds TBB platform definition, redefining the standard image ID in
order to decrease requested size in BL2 binary.
Authentication will use mbedTLS library for parsing certificate
configured with a platform configuration.

Change-Id: I9da66b915c5e9e9293fccfce92bef2434da1e430
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>

show more ...

Merge changes from topic "st-nand-updates" into integration

* changes:
feat(stm32mp1): allow to override MTD base offset
feat(stm32mp1): manage second NAND OTP on STM32MP13
feat(stm32mp1): add

Merge changes from topic "st-nand-updates" into integration

* changes:
feat(stm32mp1): allow to override MTD base offset
feat(stm32mp1): manage second NAND OTP on STM32MP13
feat(stm32mp1): add define for external scratch buffer for nand devices
feat(mtd): add platform function to allow using external buffer
feat(libc): introduce __maybe_unused

show more ...

feat(stm32mp1): allow to override MTD base offset

Add an external parameter STM32MP_FORCE_MTD_START_OFFSET that allows to
override the default FIP offset used to read the first programmed image.
It

feat(stm32mp1): allow to override MTD base offset

Add an external parameter STM32MP_FORCE_MTD_START_OFFSET that allows to
override the default FIP offset used to read the first programmed image.
It can be used for NOR, RAW_NAND or SPI_NAND boot device.

Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: Ibe664aae0e5ee90dd6629e544c9e034d751fffed

show more ...

Merge "feat(stm32mp15): manage OP-TEE shared memory" into integration

feat(stm32mp15): manage OP-TEE shared memory

On STM32MP15, there is currently an OP-TEE shared memory area at the end
of the DDR. But this area will in term be removed. To allow a smooth
transition,

feat(stm32mp15): manage OP-TEE shared memory

On STM32MP15, there is currently an OP-TEE shared memory area at the end
of the DDR. But this area will in term be removed. To allow a smooth
transition, a new flag is added (STM32MP15_OPTEE_RSV_SHM). It reflects
the OP-TEE flag: CFG_CORE_RESERVED_SHM. The flag is enabled by default
(no behavior change). It will be set to 0 when OP-TEE is aligned, and
then later be removed.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I91146cd8a26a24be22143c212362294c1e880264

show more ...

Merge changes from topic "stm32mp-emmc-boot-fip" into integration

* changes:
feat(stm32mp1): extend STM32MP_EMMC_BOOT support to FIP format
refactor(mmc): replace magic value with new PART_CFG_B

Merge changes from topic "stm32mp-emmc-boot-fip" into integration

* changes:
feat(stm32mp1): extend STM32MP_EMMC_BOOT support to FIP format
refactor(mmc): replace magic value with new PART_CFG_BOOT_PARTITION_NO_ACCESS
refactor(mmc): export user/boot partition switch functions

show more ...

feat(stm32mp1): extend STM32MP_EMMC_BOOT support to FIP format

STM32MP_EMMC_BOOT allowed placing SSBL into the eMMC boot
partition along with FSBL. This allows atomic update of both
FSBL and SSBL at

feat(stm32mp1): extend STM32MP_EMMC_BOOT support to FIP format

STM32MP_EMMC_BOOT allowed placing SSBL into the eMMC boot
partition along with FSBL. This allows atomic update of both
FSBL and SSBL at the same time. Previously, this was only
possible for the FSBL, as the eMMC layout expected by TF-A
had a single SSBL GPT partition in the eMMC user area.
TEE binaries remained in dedicated GPT partitions whether
STM32MP_EMMC_BOOT was on or off.

The new FIP format collects SSBL and TEE partitions into
a single binary placed into a GPT partition.
Extend STM32MP_EMMC_BOOT, so eMMC-booted TF-A first uses
a FIP image placed at offset 256K into the active eMMC boot
partition. If no FIP magic is detected at that offset or if
STM32MP_EMMC_BOOT is disabled, the GPT on the eMMC user area
will be consulted as before.

This allows power fail-safe update of all firmware using the
built-in eMMC boot selector mechanism, provided it fits into
the boot partition - SZ_256K. SZ_256K was chosen because it's
the same offset used with the legacy format and because it's
the size of the on-chip SRAM, where the STM32MP15x BootROM
loads TF-A into. As such, TF-A may not exceed this size limit
for existing SoCs.

Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Change-Id: Id7bec45652b3a289ca632d38d4b51316c5efdf8d

show more ...

Merge changes from topic "stm32mp13" into integration

* changes:
feat(stm32mp1): select platform compilation either by flag or DT
feat(stm32mp1-fdts): add support for STM32MP13 DK board
feat(s

Merge changes from topic "stm32mp13" into integration

* changes:
feat(stm32mp1): select platform compilation either by flag or DT
feat(stm32mp1-fdts): add support for STM32MP13 DK board
feat(stm32mp1-fdts): add DDR support for STM32MP13
feat(stm32mp1-fdts): add st-io_policies node for STM32MP13
feat(stm32mp1): updates for STM32MP13 device tree compilation
feat(stm32mp1-fdts): add DT files for STM32MP13
feat(dt-bindings): add TZC400 bindings for STM32MP13
feat(stm32mp1): add "Boot mode" management for STM32MP13
feat(stm32mp1): manage HSLV on STM32MP13
feat(stm32mp1): add sdmmc compatible in platform define
feat(st-sdmmc2): allow compatible to be defined in platform code
feat(stm32mp1): update IO compensation on STM32MP13
feat(stm32mp1): call pmic_voltages_init() in platform init
feat(st-pmic): add pmic_voltages_init() function
feat(stm32mp1): update CFG0 OTP for STM32MP13
feat(stm32mp1): usb descriptor update for STM32MP13
feat(st-clock): add clock driver for STM32MP13
feat(dt-bindings): add bindings for STM32MP13
feat(stm32mp1): get CPU info from SYSCFG on STM32MP13
feat(stm32mp1): use only one filter for TZC400 on STM32MP13
feat(stm32mp1): add a second fixed regulator
feat(stm32mp1): adaptations for STM32MP13 image header
feat(stm32mp1): update boot API for header v2.0
feat(stm32mp1): update IP addresses for STM32MP13
feat(stm32mp1): add part numbers for STM32MP13
feat(stm32mp1): chip rev. Z is 0x1001 on STM32MP13
feat(stm32mp1): update BACKUP_BOOT_MODE for STM32MP13
feat(stm32mp1): stm32mp_is_single_core() for STM32MP13
feat(stm32mp1): remove unsupported features on STM32MP13
feat(stm32mp1): update memory mapping for STM32MP13
feat(stm32mp1): introduce new flag for STM32MP13
feat(st): update stm32image tool for header v2

show more ...

feat(stm32mp1): update memory mapping for STM32MP13

SYSRAM is only 128KB and starts at 0x2FFE0000.
SRAMs are added.
BL2 code and DTB sizes are also reduced to fit in 128KB.

Change-Id: I25da99ef5c08

feat(stm32mp1): update memory mapping for STM32MP13

SYSRAM is only 128KB and starts at 0x2FFE0000.
SRAMs are added.
BL2 code and DTB sizes are also reduced to fit in 128KB.

Change-Id: I25da99ef5c08f8008ff00d38248d61b6045adad4
Signed-off-by: Yann Gautier <yann.gautier@st.com>

show more ...

Merge changes from topic "st_mapping_update" into integration

* changes:
feat(stm32mp1): enable BL2_IN_XIP_MEM to remove relocation sections
refactor(stm32mp1): reduce MMU memory regions and spl

Merge changes from topic "st_mapping_update" into integration

* changes:
feat(stm32mp1): enable BL2_IN_XIP_MEM to remove relocation sections
refactor(stm32mp1): reduce MMU memory regions and split XLAT by context
feat(st): map 2MB for ROM code
fix(stm32mp1): restrict DEVICE2 mapping in BL2

show more ...

feat(stm32mp1): enable BL2_IN_XIP_MEM to remove relocation sections

Because the BL2 is not relocated, the usage of BL2_IN_XIP_MEM
can be used. It reduces the binary size by removing all relocation
s

feat(stm32mp1): enable BL2_IN_XIP_MEM to remove relocation sections

Because the BL2 is not relocated, the usage of BL2_IN_XIP_MEM
can be used. It reduces the binary size by removing all relocation
sections. XIP will not be used when STM32MP_USE_STM32IMAGE is
defined. Introduce new definitions for SEPARATE_CODE_AND_RODATA.

Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: Ifd76f14e5bc98990bf84e0bfd4ee0b4e49a9a293

show more ...

Merge changes from topic "st_fip_fconf" into integration

* changes:
feat(plat/st): use FCONF to configure platform
feat(fdts): add STM32MP1 fw-config DT files

Merge changes from topic "st_fip_fconf" into integration

* changes:
feat(plat/st): use FIP to load images
refactor(plat/st): updates for OP-TEE
feat(lib/optee): introduce optee_header_is_valid

Merge changes from topic "st_fip_fconf" into integration

* changes:
feat(plat/st): use FIP to load images
refactor(plat/st): updates for OP-TEE
feat(lib/optee): introduce optee_header_is_valid()

show more ...

feat(plat/st): use FCONF to configure platform

Add required code to support FCONF on STM32MP1 platform.
The new FW_CONFIG DT file will be inside the FIP, and loaded by BL2.
It will be used to config

feat(plat/st): use FCONF to configure platform

Add required code to support FCONF on STM32MP1 platform.
The new FW_CONFIG DT file will be inside the FIP, and loaded by BL2.
It will be used to configure the addresses where to load other binaries.
BL2 should be agnostic of which BL32 is in the FIP (OP-TEE or SP_min),
so optee_utils.c is always compiled, and some OP-TEE flags are removed.

Change-Id: Id957b49b0117864136250bfc416664f815043ada
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>

show more ...

feat(plat/st): use FIP to load images

BL2 still uses the STM32 header binary format to be loaded from ROM code.
BL32 and BL33 and their respective device tree files are now put together
in a FIP fil

feat(plat/st): use FIP to load images

BL2 still uses the STM32 header binary format to be loaded from ROM code.
BL32 and BL33 and their respective device tree files are now put together
in a FIP file.
One DTB is created for each BL. To reduce their sizes, 2 new dtsi file are
in charge of removing useless nodes for a given BL. This is done because
BL2 and BL32 share the same device tree files base.

The previous way of booting is still available, the compilation flag
STM32MP_USE_STM32IMAGE has to be set to 1 in the make command. Some files
are duplicated and their names modified with _stm32_ to avoid too much
switches in the code.

Change-Id: I1ffada0af58486d4cf6044511b51e56b52269817
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>

show more ...