Merge changes I8f3afbe3,I441e7c69,I2e9465f7,Ib8756cd3,Iebe6ea7c, ... into integration

* changes:
plat/marvell: remove subversion from Marvell make files
drivers/marvell: check if TRNG unit is pr

Merge changes I8f3afbe3,I441e7c69,I2e9465f7,Ib8756cd3,Iebe6ea7c, ... into integration

* changes:
plat/marvell: remove subversion from Marvell make files
drivers/marvell: check if TRNG unit is present
plat/marvell: a8k: move efuse definitions to separate header
plat/marvell/armada: fix TRNG return SMC handling
drivers: marvell: comphy: add rx training on 10G port
plat/marvell/armada: postpone MSS CPU startup to BL31 stage
plat: marvell: armada: a8k: Fix LD selector mask
plat/marvell/armada: allow builds without MSS support
drivers: marvell: misc-dfx: extend dfx whitelist
drivers: marvell: add support for secure read/write of dfx register-set
ddr_phy: use smc calls to access ddr phy registers
drivers: marvell: thermal: use dedicated function for thermal SiPs
drivers: marvell: add thermal sensor driver and expose it via SIP service
fix: plat: marvell: fix MSS loader for A8K family

show more ...

plat/marvell/armada: postpone MSS CPU startup to BL31 stage

Normally the CP MSS CPU was started at the end of FW load to IRAM at BL2.
However, (especailly in secure boot mode), some bus attributes s

plat/marvell/armada: postpone MSS CPU startup to BL31 stage

Normally the CP MSS CPU was started at the end of FW load to IRAM at BL2.
However, (especailly in secure boot mode), some bus attributes should be
changed from defaults before the MSS CPU tries to access shared resources.
This patch starts to use CP MSS SRAM for FW load in both secure and
non-secure boot modes.
The FW loader inserts a magic number into MSS SRAM as an indicator of
successfully loaded FS during the BL2 stage and skips releasing the MSS
CPU from the reset state.
Then, at BL31 stage, the MSS CPU is released from reset following the
call to cp110_init function that handles all the required bus attributes
configurations.

Change-Id: Idcf81cc350a086835abed365154051dd79f1ce2e
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/46890
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>

show more ...

Merge changes I23f600b5,Icf9ffdf2,Iee7a51d1,I99afc312,I4bf8e8c0, ... into integration

* changes:
plat/marvell/armada: cleanup MSS SRAM if used for copy
plat/marvell: cn913x: allow CP1/CP2 mappin

Merge changes I23f600b5,Icf9ffdf2,Iee7a51d1,I99afc312,I4bf8e8c0, ... into integration

* changes:
plat/marvell/armada: cleanup MSS SRAM if used for copy
plat/marvell: cn913x: allow CP1/CP2 mapping at BLE stage
plat/marvell/armada/common/mss: use MSS SRAM in secure mode
include/drivers/marvell/mochi: add detection of secure mode
plat/marvell: fix SPD handling in dram port
marvell: drivers: move XOR0/1 DIOB from WIN 0 to 1
drivers/marvell/mochi: add support for cn913x in PCIe EP mode
drivers/marvell/mochi: add missing stream IDs configurations
plat/marvell/armada/a8k: support HW RNG by SMC
drivers/rambus: add TRNG-IP-76 driver

show more ...

plat/marvell/armada/common/mss: use MSS SRAM in secure mode

The CP MSS IRAM is only accessible by CM3 CPU and MSS DMA.
In secure boot mode the MSS DMA is unable to directly load
the MSS FW image fro

plat/marvell/armada/common/mss: use MSS SRAM in secure mode

The CP MSS IRAM is only accessible by CM3 CPU and MSS DMA.
In secure boot mode the MSS DMA is unable to directly load
the MSS FW image from DRAM to IRAM.
This patch adds support for using the MSS SRAM as intermediate
storage. The MSS FW image is loaded by application CPU into the
MSS SRAM first, then transferred to MSS IRAM by MSS DMA.
Such change allows the CP MSS image load in secure mode.

Change-Id: Iee7a51d157743a0bdf8acb668ee3d599f760a712
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaszczyk@marvell.com>

show more ...

Merge changes from topic "release/14.0" into integration

* changes:
docs: marvell: update PHY porting layer description
docs: marvell: update path in marvell documentation
docs: marvell: updat

Merge changes from topic "release/14.0" into integration

* changes:
docs: marvell: update PHY porting layer description
docs: marvell: update path in marvell documentation
docs: marvell: update build instructions with CN913x
plat: marvell: octeontx: add support for t9130
plat: marvell: t9130: add SVC support
plat: marvell: t9130: update AVS settings
plat: marvell: t9130: pass actual CP count for load_image
plat: marvell: armada: a7k: add support to SVC validation mode
plat: marvell: armada: add support for twin-die combined memory device

show more ...

plat: marvell: t9130: pass actual CP count for load_image

Add CN913x case to bl2_plat_get_cp_count.
Fix loading of cp1/2 image. This is a preparation
patch for adding CN913x SoC family support.

Cha

plat: marvell: t9130: pass actual CP count for load_image

Add CN913x case to bl2_plat_get_cp_count.
Fix loading of cp1/2 image. This is a preparation
patch for adding CN913x SoC family support.

Change-Id: Id84a30203d20572fc0dfd3f91ea395c199a85fe9
Signed-off-by: Ben Peled <bpeled@marvell.com>

show more ...

Merge changes Ib9c82b85,Ib348e097,I4dc315e4,I58a8ce44,Iebc03361, ... into integration

* changes:
plat: marvell: armada: a8k: add OP-TEE OS MMU tables
drivers: marvell: add support for mapping th

Merge changes Ib9c82b85,Ib348e097,I4dc315e4,I58a8ce44,Iebc03361, ... into integration

* changes:
plat: marvell: armada: a8k: add OP-TEE OS MMU tables
drivers: marvell: add support for mapping the entire LLC to SRAM
plat: marvell: armada: add LLC SRAM CCU setup for AP806/AP807 platforms
plat: marvell: armada: reduce memory size reserved for FIP image
plat: marvell: armada: platform definitions cleanup
plat: marvell: armada: a8k: check CCU window state before loading MSS BL2
drivers: marvell: add CCU driver API for window state checking
drivers: marvell: align and extend llc macros
plat: marvell: a8k: move address config of cp1/2 to BL2
plat: marvell: armada: re-enable BL32_BASE definition
plat: marvell: a8k: extend includes to take advantage of the phy_porting_layer
marvell: comphy: initialize common phy selector for AP mode
marvell: comphy: update rx_training procedure
plat: marvell: armada: configure amb for all CPs
plat: marvell: armada: modify PLAT_FAMILY name for 37xx SoCs

show more ...

plat: marvell: armada: a8k: check CCU window state before loading MSS BL2

Make sure the current CCU window is not in use before adding
a new address map during MSS BL2 image load preparations.
At BL

plat: marvell: armada: a8k: check CCU window state before loading MSS BL2

Make sure the current CCU window is not in use before adding
a new address map during MSS BL2 image load preparations.
At BL2 stage the CCU Win-2 points to DRAM. If additional mapping is
added to MSS BL2 stage initialization, the DDR entry will be destroyed
and lead to the system hang.

Change-Id: I215e83508acc37d54dab6954d791b9a74cc883ca
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

show more ...

plat: marvell: a8k: move address config of cp1/2 to BL2

The configuration space of each standalone CP was updated in BL31.
Loading FW procedure take places earlier in SCP_BL2.
It needs to be done af

plat: marvell: a8k: move address config of cp1/2 to BL2

The configuration space of each standalone CP was updated in BL31.
Loading FW procedure take places earlier in SCP_BL2.
It needs to be done after access to each CP is provided.
Moving the proper configuration from BL31 to BL2 solves it.

Change-Id: I44cf88dfd4ebf09130544332bfdd3d16ef2674ea
Signed-off-by: Ben Peled <bpeled@marvell.com>

show more ...

plat: marvell: armada: configure amb for all CPs

Before this patch the configuration took place only for CP0 and CP1, but
since new platforms can contains up to 3 CPs update is required.

Change-Id:

plat: marvell: armada: configure amb for all CPs

Before this patch the configuration took place only for CP0 and CP1, but
since new platforms can contains up to 3 CPs update is required.

Change-Id: Iebd50bbe7b9772063e2c4efb3a7ecbfd593e950d
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

show more ...

Merge changes I80316689,I23cac4fb,If911e7de,I169ff358,I4e040cd5, ... into integration

* changes:
ddr: a80x0: add DDR 32-bit ECC mode support
ble: ap807: improve PLL configuration sequence
ble:

Merge changes I80316689,I23cac4fb,If911e7de,I169ff358,I4e040cd5, ... into integration

* changes:
ddr: a80x0: add DDR 32-bit ECC mode support
ble: ap807: improve PLL configuration sequence
ble: ap807: clean-up PLL configuration sequence
ddr: a80x0: add DDR 32-bit mode support
plat: marvell: mci: perform mci link tuning for all mci interfaces
plat: marvell: mci: use more meaningful name for mci link tuning
plat: marvell: a8k: remove wrong or unnecessary comments
plat: marvell: ap807: enable snoop filter for ap807
plat: marvell: ap807: update configuration space of each CP
plat: marvell: ap807: use correct address for MCIx4 register
plat: marvell: add support for PLL 2.2GHz mode
plat: marvell: armada: make a8k_common.mk and mss_common.mk more generic
marvell: armada: add extra level in marvell platform hierarchy

show more ...

marvell: armada: add extra level in marvell platform hierarchy

This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
pla

marvell: armada: add extra level in marvell platform hierarchy

This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
plat, include/plat) are moved to the new "armada" sub-folder.

Change-Id: Icf03356187078ad6a2e56c9870992be3ca4c9655
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>

show more ...