Merge changes I23f600b5,Icf9ffdf2,Iee7a51d1,I99afc312,I4bf8e8c0, ... into integration

* changes:
plat/marvell/armada: cleanup MSS SRAM if used for copy
plat/marvell: cn913x: allow CP1/CP2 mappin

Merge changes I23f600b5,Icf9ffdf2,Iee7a51d1,I99afc312,I4bf8e8c0, ... into integration

* changes:
plat/marvell/armada: cleanup MSS SRAM if used for copy
plat/marvell: cn913x: allow CP1/CP2 mapping at BLE stage
plat/marvell/armada/common/mss: use MSS SRAM in secure mode
include/drivers/marvell/mochi: add detection of secure mode
plat/marvell: fix SPD handling in dram port
marvell: drivers: move XOR0/1 DIOB from WIN 0 to 1
drivers/marvell/mochi: add support for cn913x in PCIe EP mode
drivers/marvell/mochi: add missing stream IDs configurations
plat/marvell/armada/a8k: support HW RNG by SMC
drivers/rambus: add TRNG-IP-76 driver

show more ...

plat/marvell: fix SPD handling in dram port

The DRAM port code issues a dummy write to SPD page-0 i2c address
in order to select this page for the forthcoming read transaction.
If the write buffer l

plat/marvell: fix SPD handling in dram port

The DRAM port code issues a dummy write to SPD page-0 i2c address
in order to select this page for the forthcoming read transaction.
If the write buffer length supplied to i2c_write is not zero, this
call is translated to 2 bus transations:

- set the target offset
- write the data to the target

However no actual data should be transferred to SPD page-0 in order
to select it. Actually, the second transation never receives an ACK
from the target device, which caused the following error report:

ERROR: Status 30 in write transaction

This patch sets the buffer length in page-0 select writes to zero,
leading to bypass the data transfer to the target device.
Issuing the target offset command to SPD page-0 address effectively
selects this page for the read operation.

Change-Id: I4bf8e8c09da115ee875f934bc8fbc9349b995017
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/24387
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Moti Buskila <motib@marvell.com>

show more ...

Merge changes from topic "release/14.0" into integration

* changes:
docs: marvell: update PHY porting layer description
docs: marvell: update path in marvell documentation
docs: marvell: updat

Merge changes from topic "release/14.0" into integration

* changes:
docs: marvell: update PHY porting layer description
docs: marvell: update path in marvell documentation
docs: marvell: update build instructions with CN913x
plat: marvell: octeontx: add support for t9130
plat: marvell: t9130: add SVC support
plat: marvell: t9130: update AVS settings
plat: marvell: t9130: pass actual CP count for load_image
plat: marvell: armada: a7k: add support to SVC validation mode
plat: marvell: armada: add support for twin-die combined memory device

show more ...

plat: marvell: armada: add support for twin-die combined memory device

the twin-die combined memory device should be treated as
X8 device and not as X16 one. This patch is required to
re-enable comp

plat: marvell: armada: add support for twin-die combined memory device

the twin-die combined memory device should be treated as
X8 device and not as X16 one. This patch is required to
re-enable compilation after BLE (mv-ddr-marvell) firmware upgrade.

Change-Id: I41257ff2825164ebca85a84bbb8462d7b3447b97
Signed-off-by: Moti Buskila <motib@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>

show more ...

Merge changes I80316689,I23cac4fb,If911e7de,I169ff358,I4e040cd5, ... into integration

* changes:
ddr: a80x0: add DDR 32-bit ECC mode support
ble: ap807: improve PLL configuration sequence
ble:

Merge changes I80316689,I23cac4fb,If911e7de,I169ff358,I4e040cd5, ... into integration

* changes:
ddr: a80x0: add DDR 32-bit ECC mode support
ble: ap807: improve PLL configuration sequence
ble: ap807: clean-up PLL configuration sequence
ddr: a80x0: add DDR 32-bit mode support
plat: marvell: mci: perform mci link tuning for all mci interfaces
plat: marvell: mci: use more meaningful name for mci link tuning
plat: marvell: a8k: remove wrong or unnecessary comments
plat: marvell: ap807: enable snoop filter for ap807
plat: marvell: ap807: update configuration space of each CP
plat: marvell: ap807: use correct address for MCIx4 register
plat: marvell: add support for PLL 2.2GHz mode
plat: marvell: armada: make a8k_common.mk and mss_common.mk more generic
marvell: armada: add extra level in marvell platform hierarchy

show more ...

marvell: armada: add extra level in marvell platform hierarchy

This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
pla

marvell: armada: add extra level in marvell platform hierarchy

This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
plat, include/plat) are moved to the new "armada" sub-folder.

Change-Id: Icf03356187078ad6a2e56c9870992be3ca4c9655
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>

show more ...