xref: /utopia/UTPA2-700.0.x/projects/tmplib/include/drvMVOP.h (revision 53ee8cc121a030b8d368113ac3e966b4705770ef)

//<MStar Software>
//******************************************************************************
// MStar Software
// Copyright (c) 2010 - 2012 MStar Semiconductor, Inc. All rights reserved.
// All software, firmware and related documentation herein ("MStar Software") are
// intellectual property of MStar Semiconductor, Inc. ("MStar") and protected by
// law, including, but not limited to, copyright law and international treaties.
// Any use, modification, reproduction, retransmission, or republication of all
// or part of MStar Software is expressly prohibited, unless prior written
// permission has been granted by MStar.
//
// By accessing, browsing and/or using MStar Software, you acknowledge that you
// have read, understood, and agree, to be bound by below terms ("Terms") and to
// comply with all applicable laws and regulations:
//
// 1. MStar shall retain any and all right, ownership and interest to MStar
//    Software and any modification/derivatives thereof.
//    No right, ownership, or interest to MStar Software and any
//    modification/derivatives thereof is transferred to you under Terms.
//
// 2. You understand that MStar Software might include, incorporate or be
//    supplied together with third party`s software and the use of MStar
//    Software may require additional licenses from third parties.
//    Therefore, you hereby agree it is your sole responsibility to separately
//    obtain any and all third party right and license necessary for your use of
//    such third party`s software.
//
// 3. MStar Software and any modification/derivatives thereof shall be deemed as
//    MStar`s confidential information and you agree to keep MStar`s
//    confidential information in strictest confidence and not disclose to any
//    third party.
//
// 4. MStar Software is provided on an "AS IS" basis without warranties of any
//    kind. Any warranties are hereby expressly disclaimed by MStar, including
//    without limitation, any warranties of merchantability, non-infringement of
//    intellectual property rights, fitness for a particular purpose, error free
//    and in conformity with any international standard.  You agree to waive any
//    claim against MStar for any loss, damage, cost or expense that you may
//    incur related to your use of MStar Software.
//    In no event shall MStar be liable for any direct, indirect, incidental or
//    consequential damages, including without limitation, lost of profit or
//    revenues, lost or damage of data, and unauthorized system use.
//    You agree that this Section 4 shall still apply without being affected
//    even if MStar Software has been modified by MStar in accordance with your
//    request or instruction for your use, except otherwise agreed by both
//    parties in writing.
//
// 5. If requested, MStar may from time to time provide technical supports or
//    services in relation with MStar Software to you for your use of
//    MStar Software in conjunction with your or your customer`s product
//    ("Services").
//    You understand and agree that, except otherwise agreed by both parties in
//    writing, Services are provided on an "AS IS" basis and the warranty
//    disclaimer set forth in Section 4 above shall apply.
//
// 6. Nothing contained herein shall be construed as by implication, estoppels
//    or otherwise:
//    (a) conferring any license or right to use MStar name, trademark, service
//        mark, symbol or any other identification;
//    (b) obligating MStar or any of its affiliates to furnish any person,
//        including without limitation, you and your customers, any assistance
//        of any kind whatsoever, or any information; or
//    (c) conferring any license or right under any intellectual property right.
//
// 7. These terms shall be governed by and construed in accordance with the laws
//    of Taiwan, R.O.C., excluding its conflict of law rules.
//    Any and all dispute arising out hereof or related hereto shall be finally
//    settled by arbitration referred to the Chinese Arbitration Association,
//    Taipei in accordance with the ROC Arbitration Law and the Arbitration
//    Rules of the Association by three (3) arbitrators appointed in accordance
//    with the said Rules.
//    The place of arbitration shall be in Taipei, Taiwan and the language shall
//    be English.
//    The arbitration award shall be final and binding to both parties.
//
//******************************************************************************
//<MStar Software>
////////////////////////////////////////////////////////////////////////////////
//
// Copyright (c) 2008-2009 MStar Semiconductor, Inc.
// All rights reserved.
//
// Unless otherwise stipulated in writing, any and all information contained
// herein regardless in any format shall remain the sole proprietary of
// MStar Semiconductor Inc. and be kept in strict confidence
// ("MStar Confidential Information") by the recipient.
// Any unauthorized act including without limitation unauthorized disclosure,
// copying, use, reproduction, sale, distribution, modification, disassembling,
// reverse engineering and compiling of the contents of MStar Confidential
// Information is unlawful and strictly prohibited. MStar hereby reserves the
// rights to any and all damages, losses, costs and expenses resulting therefrom.
//
////////////////////////////////////////////////////////////////////////////////

///////////////////////////////////////////////////////////////////////////////////////////////////
///
/// @file   drvMVOP.h
/// @brief  MVOP Driver Interface
/// @author MStar Semiconductor Inc.
///////////////////////////////////////////////////////////////////////////////////////////////////

/*!
 \defgroup MVOP MVOP interface (drvMVOP.h)
 \ingroup VDEC

 <b> MVOP api flow </b> \n
   \image html drvMVOP_flow.png

 \defgroup MVOP MVOP module
 \ingroup  MVOP
 \defgroup MVOP_Basic MVOP_Basic
 \ingroup MVOP
 \defgroup MVOP_SetCommand MVOP SetCommand
 \ingroup MVOP
 \defgroup MVOP_GetCommand MVOP GetCommand
 \ingroup MVOP
 \defgroup MVOP_Debug MVOP Debug
 \ingroup MVOP
*/

#ifndef _DRV_MVOP_H_
#define _DRV_MVOP_H_

#ifdef __cplusplus
extern "C"
{
#endif
#include "MsDevice.h"
#include "UFO.h"

//-------------------------------------------------------------------------------------------------
//  Driver Capability
//-------------------------------------------------------------------------------------------------


//-------------------------------------------------------------------------------------------------
//  Macro and Define
//-------------------------------------------------------------------------------------------------
/// Version string.
#define MSIF_MVOP_LIB_CODE              {'M','V','O','P'}    //Lib code
#define MSIF_MVOP_LIBVER                {'1','0'}            //LIB version
#define MSIF_MVOP_BUILDNUM              {'4','2'}            //Build Number
#define MSIF_MVOP_CHANGELIST            {'0','0','7','0','2','3','8','3'} //P4 ChangeList Number

#define MVOP_DRV_VERSION                /* Character String for DRV/API version             */  \
    MSIF_TAG,                           /* 'MSIF'                                           */  \
    MSIF_CLASS,                         /* '00'                                             */  \
    MSIF_CUS,                           /* 0x0000                                           */  \
    MSIF_MOD,                           /* 0x0000                                           */  \
    MSIF_CHIP,                                                                                  \
    MSIF_CPU,                                                                                   \
    MSIF_MVOP_LIB_CODE,                 /* IP__                                             */  \
    MSIF_MVOP_LIBVER,                   /* 0.0 ~ Z.Z                                        */  \
    MSIF_MVOP_BUILDNUM,                 /* 00 ~ 99                                          */  \
    MSIF_MVOP_CHANGELIST,               /* CL#                                              */  \
    MSIF_OS


#define _SUPPORT_IMG_OFFSET_
#define ENABLE_UTOPIA2_INTERFACE   1
#define ENABLE_MUTEX                1

//-------------------------------------------------------------------------------------------------
//  Type and Structure
//-------------------------------------------------------------------------------------------------
typedef enum
{
    E_MVOP_OK            = 0,
    E_MVOP_FAIL          = 1,
    E_MVOP_INVALID_PARAM = 2,
    E_MVOP_NOT_INIT      = 3,
    E_MVOP_UNSUPPORTED   = 4
} MVOP_Result;

/// MVOP tile format
typedef enum
{
    E_MVOP_TILE_8x32  = 0,
    E_MVOP_TILE_16x32 = 1,
    E_MVOP_TILE_NONE  = 2,
    E_MVOP_TILE_32x16 = 3,
    E_MVOP_TILE_32x32 = 4
} MVOP_TileFormat;

/// MVOP RGB format
typedef enum
{
    E_MVOP_RGB_565  = 0,
    E_MVOP_RGB_888  = 1,
    E_MVOP_RGB_NONE = 0xff
} MVOP_RgbFormat;

/// MVOP input mode
typedef enum
{
    VOPINPUT_HARDWIRE = 0,        //!< hardwire mode (MVD)
    VOPINPUT_HARDWIRECLIP = 1,    //!< hardware clip mode (MVD)
    VOPINPUT_MCUCTRL = 2,         //!< MCU control mode (M4VD, JPG)
    VOPINPUT_IFRAME = 3,          //!< MCU control mode (MVD)
} VOPINPUTMODE;

/// MVOP input mode
typedef enum
{
    E_VOPMIRROR_VERTICAL      = 1,
    E_VOPMIRROR_HORIZONTALL   =  2,
    E_VOPMIRROR_HVBOTH       =  3,
    E_VOPMIRROR_NONE         =  4,
} MVOP_DrvMirror;

/// MVOP repeat field mode
typedef enum
{
    E_MVOP_RPTFLD_NONE = 0,     //!< normal display top and bottom fields
    E_MVOP_RPTFLD_TOP  = 1,     //!< top field
    E_MVOP_RPTFLD_BOT  = 2,     //!< bottom field
} MVOP_RptFldMode;

/// MVOP Output 3D Type
typedef enum
{
    E_MVOP_OUTPUT_3D_NONE, //!< Output 2D
    E_MVOP_OUTPUT_3D_TB,   //!< Output Top Bottom
    E_MVOP_OUTPUT_3D_SBS,  //!< Output Side By Side
    E_MVOP_OUTPUT_3D_LA,   //!< Output Line Alternative
    E_MVOP_OUTPUT_3D_MAXNUM,
}EN_MVOP_Output_3D_TYPE;

typedef enum
{
    MVOP_MPEG4 = 0,
    MVOP_MJPEG,
    MVOP_H264,
    // <ATV MM>
    MVOP_RM, //jyliu.rm
    MVOP_TS,
    MVOP_MPG,
    MVOP_UNKNOW,
    // </ATV MM>
}MVOP_VIDEO_TYPE;


/// MVOP input parameter
typedef struct
{
    MS_PHY u32YOffset;
    MS_PHY u32UVOffset;
    MS_U16 u16HSize;
    MS_U16 u16VSize;
    MS_U16 u16StripSize;

    MS_BOOL bYUV422;    //!< YUV422 or YUV420
    MS_BOOL bSD;        //!< SD or HD
    MS_BOOL bProgressive;   //!< Progressive or Interlace

    // in func MDrv_MVOP_Input_Mode(), bSD is used to set dc_strip[7:0].
    // in func MDrv_MVOP_Input_Mode_Ext(), bSD is don't care and
    //    dc_strip[7:0] is set according to Hsize
    MS_BOOL bUV7bit;        // +S3, UV 7 bit or not
    MS_BOOL bDramRdContd;   // +S3, continue read out or jump 32
    MS_BOOL bField;         // +S3, Field 0 or 1 //(stbdc)for u4 bottom field enabled when bfield is true
    MS_BOOL b422pack;       // +S3, YUV422 pack mode
    MS_U16 u16CropX;
    MS_U16 u16CropY;
    MS_U16 u16CropWidth;
    MS_U16 u16CropHeight;
    MVOP_VIDEO_TYPE enVideoType;
} MVOP_InputCfg;


typedef struct
{
    MS_U16 u16V_TotalCount;        ///< Vertical total count
    MS_U16 u16H_TotalCount;        ///< Horizontal total count
    MS_U16 u16VBlank0_Start;       ///< Vertical blank 0 start
    MS_U16 u16VBlank0_End;         ///< Vertical blank 0 End
    MS_U16 u16VBlank1_Start;       ///< Vertical blank 1 start
    MS_U16 u16VBlank1_End;         ///< Vertical blank 1 End
    MS_U16 u16TopField_Start;      ///< Top field start
    MS_U16 u16BottomField_Start;   ///< bottom field start
    MS_U16 u16TopField_VS;         ///< top field vsync
    MS_U16 u16BottomField_VS;      ///< bottom field vsync
    MS_U16 u16HActive_Start;       ///< Horizontal disaply start

    MS_BOOL bInterlace;            ///< interlace or not
    MS_U8 u8Framerate;             ///< frame rate
    MS_U16 u16H_Freq ;             ///< horizontal frequency
    MS_U16 u16Num;                 ///< MVOP SYNTHESIZER numerator
    MS_U16 u16Den;                 ///< MVOP SYNTHESIZER denumerator
    MS_U8 u8MvdFRCType;            ///< flag for frame rate convert

    MS_U16 u16ExpFrameRate;        ///< Frame Rate
    MS_U16 u16Width;               ///< Width
    MS_U16 u16Height;              ///< Height
    MS_U16 u16HImg_Start;          ///< Horizontal disaply start
    MS_U16 u16VImg_Start0;         ///< Vertical disaply start
    MS_U16 u16VImg_Start1;         ///< Vertical disaply start
    MS_BOOL bHDuplicate;           ///< flag for vop horizontal duplicate
} MVOP_Timing;

//Display information For GOP
typedef struct
{
    MS_U32 VDTOT; //Output vertical total
    MS_U32 DEVST; //Output DE vertical start
    MS_U32 DEVEND;//Output DE Vertical end
    MS_U32 HDTOT;// Output horizontal total
    MS_U32 DEHST; //Output DE horizontal start
    MS_U32 DEHEND;// Output DE horizontal end
    MS_BOOL bInterlaceMode;
}MVOP_DST_DispInfo;

//MVOP timing information from mvop registers
typedef struct
{
    MS_U16 u16V_TotalCount;        ///< Vertical total count
    MS_U16 u16H_TotalCount;        ///< Horizontal total count
    MS_U16 u16VBlank0_Start;       ///< Vertical blank 0 start
    MS_U16 u16VBlank0_End;         ///< Vertical blank 0 End
    MS_U16 u16VBlank1_Start;       ///< Vertical blank 1 start
    MS_U16 u16VBlank1_End;         ///< Vertical blank 1 End
    MS_U16 u16TopField_Start;      ///< Top field start
    MS_U16 u16BottomField_Start;   ///< bottom field start
    MS_U16 u16TopField_VS;         ///< top field vsync
    MS_U16 u16BottomField_VS;      ///< bottom field vsync
    MS_U16 u16HActive_Start;       ///< Horizontal disaply start
    MS_BOOL bInterlace;            ///< interlace or not
    MS_BOOL bEnabled;              ///< MVOP is enabled or not
}MVOP_TimingInfo_FromRegisters;

typedef enum
{
    MVOP_PATTERN_NORMAL     = 0,
    MVOP_PATTERN_COLORBAR   = 1,
    MVOP_PATTERN_FRAMECOLOR = 2,
    MVOP_PATTERN_YCBCR      = 3,
    MVOP_PATTERN_Y          = 4,
    MVOP_PATTERN_CB         = 5,
    MVOP_PATTERN_CR         = 6,
    MVOP_PATTERN_DEFAULT    = 7   //new pattern = (last parrtern + 1) % MVOP_PATTERN_DEFAULT
} MVOP_Pattern;

typedef enum
{
    MVOP_INPUT_DRAM = 0,
    MVOP_INPUT_H264 = 1,    //SVD for T2
    MVOP_INPUT_MVD  = 2,
    MVOP_INPUT_RVD  = 3,
    MVOP_INPUT_CLIP = 4,
    MVOP_INPUT_JPD  = 5,
    MVOP_INPUT_HVD_3DLR = 6,    ///< HVD 3D L/R mode
    MVOP_INPUT_MVD_3DLR = 7,    ///< MVD 3D L/R mode
    MVOP_INPUT_DRAM_3DLR= 8,
    MVOP_INPUT_EVD = 9,
    MVOP_INPUT_EVD_3DLR = 10,
    MVOP_INPUT_VP9 = 11,
    MVOP_INPUT_UNKNOWN = -1
} MVOP_InputSel;

/// MVOP VideoStat data structure
typedef struct
{
    MS_U16 u16HorSize;
    MS_U16 u16VerSize;
    MS_U16 u16FrameRate;
    MS_U8 u8AspectRate;
    MS_U8 u8Interlace;
    MS_U16 u16HorOffset;
    MS_U16 u16VerOffset;
} MVOP_VidStat;

/// MVOP driver info.
typedef struct _MVOP_DrvInfo
{
    MS_U32 u32MaxSynClk;
    MS_U32 u32MinSynClk;
    MS_U32 u32MaxFreerunClk;
} MVOP_DrvInfo;

///MVOP driver status
typedef struct _MVOP_DrvStatus
{
    MS_BOOL bIsInit;
    MS_BOOL bIsEnable;
    MS_BOOL bIsUVShift;
    MS_BOOL bIsBlackBG;
    MS_BOOL bIsMonoMode;
    MS_BOOL bIsSetTiming;
} MVOP_DrvStatus;

///MVOP module enum
typedef enum
{
    E_MVOP_MODULE_MAIN = 0,
    E_MVOP_MODULE_SUB  = 1,
    E_MVOP_MODULE_MAX
} MVOP_Module;

///MVOP device enum
typedef enum
{
    E_MVOP_DEV_0    = 0,    ///< Main mvop
    E_MVOP_DEV_1    = 1,    ///< Sub mvop
    E_MVOP_DEV_2    = 2,    ///< 3rd mvop
    E_MVOP_DEV_NONE = 0xff
} MVOP_DevID;

///MVOP handle to carry out MVOP info.
typedef struct _MVOP_Handle
{
    MVOP_Module eModuleNum;
} MVOP_Handle;


typedef enum
{
    E_MVOP_MAIN_VIEW    = 0,
    E_MVOP_2ND_VIEW     = 0x01, ///< buffer underflow
} MVOP_3DView;

typedef struct
{
    MVOP_3DView eView;
    MS_PHY u32YOffset;
    MS_PHY u32UVOffset;
} MVOP_BaseAddInput;

typedef struct
{
    MS_BOOL bIsEnableLuma;
    MS_BOOL bIsEnableChroma;
    MS_U8 u8LumaValue;
    MS_U8 u8ChromaValue;
} MVOP_VC1RangeMapInfo;

typedef struct
{
    MS_PHY u32MSBYOffset;
    MS_PHY u32MSBUVOffset;
    MS_PHY u32LSBYOffset;
    MS_PHY u32LSBUVOffset;
    MS_BOOL bProgressive;
    MS_BOOL b422Pack;
    MS_BOOL bEnLSB;
} MVOP_EVDBaseAddInput;

typedef enum
{
    E_MVOP_EVD_8BIT    = 0,
    E_MVOP_EVD_10BIT     = 0x01, ///< buffer underflow
} MVOP_EVDBit;

typedef struct
{
    MS_BOOL bEnableEVD;
    MVOP_EVDBit eEVDBit[2];
}MVOP_EVDFeature;

typedef enum
{
    E_MVOP_MAIN_STREAM    = 0,
    //E_MVOP_2nd_STREAM     = 1,
} MVOP_StreamID;

///MVOP set command used by MDrv_MVOP_SetCommand()
typedef enum
{
    E_MVOP_CMD_SET_TYPE = 0x100,
    E_MVOP_CMD_SET_VSIZE_MIN,             ///< 0x101 Enable vsize minimum checking
    E_MVOP_CMD_SET_STB_FD_MASK_CLR,       ///< 0x102 Force set fd_mask to low
    E_MVOP_CMD_SET_3DLR_INST_VBLANK,      ///< 0x103 Vertical blanking lines between L & R for 3D L/R mode.
    E_MVOP_CMD_SET_3DLR_ALT_OUT,          ///< 0x104 Alternative lines output for 3D L/R mode. If interlace output, both view output the same field.
    E_MVOP_CMD_SET_RGB_FMT,               ///< 0x105 RGB format input: MVOP_RgbFormat.
    E_MVOP_CMD_SET_SW_CTRL_FIELD_ENABLE,  ///< 0x106 Force read top or bottom field.
    E_MVOP_CMD_SET_SW_CTRL_FIELD_DSIABLE, ///< 0x107 Disable force read control
    E_MVOP_CMD_SET_3DLR_2ND_CFG,          ///< 0x108 Enable supporting 2nd pitch(h/vsize) for 3D L/R mode.
    E_MVOP_CMD_SET_VSIZE_DUPLICATE,       ///< 0x109 Enable/Disable VSize duplicate.
    E_MVOP_CMD_SET_3DLR_ALT_OUT_SBS,      ///< 0x10A Line alternative read of 3D L/R mode, side-by-side output.
    E_MVOP_CMD_SET_FIELD_DUPLICATE,       ///< 0x10B Repeat field for interlace source. (only input one field)
    E_MVOP_CMD_SET_VSYNC_MODE,            ///< 0x10C Set VSync mode (0: original; 1: new)
    E_MVOP_CMD_SET_VSIZE_X4_DUPLICATE,       ///< 0x10D Enable/Disable VSize x4 duplicate.
    E_MVOP_CMD_SET_HSIZE_X4_DUPLICATE,       ///< 0x10E Enable/Disable VSize x4 duplicate.
    E_MVOP_CMD_SET_BASE_ADD_MULTI_VIEW,  ///< 0x10F Set Muiltiple view Base Address for 3D L/R mode.
    E_MVOP_CMD_SET_FIRE_MVOP,             ///< 0x110 Force load MVOP register in.
    E_MVOP_CMD_SET_VC1_RANGE_MAP,         ///< 0x111 Set VC1 Range Map Luma/Chroma Address
    E_MVOP_CMD_SET_POWER_STATE,           ///< 0x112 Set MVOP STR(suspend/resume)
    E_MVOP_CMD_SET_420_BW_SAVING_MODE,   ///< 0X113 Set MVOP BW SAVING MODE(0:original 1:save 1/4 bw)
    E_MVOP_CMD_SET_EVD_BASE_ADD,          ///< 0x114 Set 10bits or 8bits base addresss for EVD.
    E_MVOP_CMD_SET_EVD_FEATURE,          ///< 0x115 Set EVD Mode and 10bits or 8 bits Enable.
    E_MVOP_CMD_SET_MVD_LATE_REPEAT,      ////<0x116 Set repeat previous frame if HVD/MVD can not finish vsync.
    E_MVOP_CMD_SET_HANDSHAKE_MODE,      ////<0x117 TV chip support handshake mode after muji and monet.
    E_MVOP_CMD_SET_FRC_OUTPUT,          ////<0x118 Reset MVOP output timing.

    E_MVOP_CMD_GET_TYPE = 0x400,
    E_MVOP_CMD_GET_3DLR_ALT_OUT,                ///< 0x401 Query if it is 3D L/R alternative lines output.
    E_MVOP_CMD_GET_MIRROR_MODE,                 ///< 0x402 Get Mirror Mode
    E_MVOP_CMD_GET_3DLR_2ND_CFG,                ///< 0x403 Get if 3D LR 2nd pitch is enabled.
    E_MVOP_CMD_GET_VSIZE_DUPLICATE,             ///< 0x404 Get if VSize duplicate is enabled.
    E_MVOP_CMD_GET_BASE_ADD_BITS,               ///< 0x405 Get bits of y/uv address.
    E_MVOP_CMD_GET_TOTAL_MVOP_NUM,              ///<0X406 Get how many mvop in this chip.
    E_MVOP_CMD_GET_MAXIMUM_CLK,                 ///< 0x407 Get maximum mvop(dc0) clock.
    E_MVOP_CMD_GET_CURRENT_CLK,                 ///< 0x408 Get current mvop(dc0) clock.
    E_MVOP_CMD_GET_BASE_ADD_MULTI_VIEW,        ///< 0x409 Get base address of main/sub view.
    E_MVOP_CMD_GET_TOP_FIELD_IMAGE_VSTART,     ///< 0x40A Get top field vstart.
    E_MVOP_CMD_GET_BOTTOM_FIELD_IMAGE_VSTART,  ///< 0x40B Get bot field vstart.
    E_MVOP_CMD_GET_VCOUNT,                       ///< 0x40C Get tgen vcount.
    E_MVOP_CMD_GET_HANDSHAKE_MODE,              ///< 0x40D Get Handshaking mode status.
    E_MVOP_CMD_GET_MAX_FPS,                      ///< 0x40E Get mvop supporting max framerate.
    E_MVOP_CMD_GET_CROP_FOR_XC,                 ///< 0x40F Set crop and Get crop infomation. Without set register.
    E_MVOP_CMD_GET_MVOP_SW_CROP_ADD,          ///< 0x410 If hw not support crop, sw patch for base address.
    E_MVOP_CMD_GET_IS_SW_CROP,                  ///< 0x411 If hw not support crop or not?
    E_MVOP_CMD_GET_OUTPUT_HV_RATIO,             //<0x412 Get mvop output HV ratio.
} MVOP_Command;

typedef enum
{
    E_MVOP_SYNCMODE,
    E_MVOP_FREERUNMODE,
    E_MVOP_27MHZ = 27000000ul,
    E_MVOP_54MHZ = 54000000ul,
    E_MVOP_72MHZ = 72000000ul,
    E_MVOP_108MHZ = 108000000ul,
    E_MVOP_123MHZ = 123000000ul,
    E_MVOP_144MHZ = 144000000ul,
    E_MVOP_160MHZ = 160000000ul,
    E_MVOP_172MHZ = 172000000ul,
    E_MVOP_192MHZ = 192000000ul,
    E_MVOP_320MHZ = 320000000ul,
}MVOP_FREQUENCY;

// Interrupt
typedef enum
{
    E_MVOP_INT_NONE    = 0,
    E_MVOP_INT_BUFF_UF = 0x01, ///< buffer underflow
    E_MVOP_INT_BUFF_OF = 0x02, ///< buffer overflow
    E_MVOP_INT_VSYNC   = 0x04, ///< Vsync interrupt
    E_MVOP_INT_HSYNC   = 0x08, ///< Hsync interrupt
    E_MVOP_INT_RDY     = 0x10, ///< DC ready interrupt
    E_MVOP_INT_FDCHNG  = 0x20, ///< field change
} MVOP_IntType;

typedef struct
{
    MS_U8  u8StrVer;
    MS_U8  u8Rsrvd;
    MS_U16 u16HSize;
    MS_U16 u16VSize;
    MS_U16 u16Fps;
} MVOP_CapInput;

typedef struct
{
    MS_BOOL  bEnable3DLRALT;
    MS_BOOL  bEnable3DLRSBS;
    MS_BOOL  bEnableVdup;
    MS_BOOL  bEnableVx4;
    MS_BOOL  bEnableHx4;
    MS_BOOL  bEnableVsyncMode;
    MS_BOOL  bEnableHMirror;
    MS_BOOL  bEnableVMirror;
    MS_BOOL  bEnableBWSave;
    MS_BOOL  bEnableRptPreVsync;
} MVOP_ComdFlag;

typedef enum
{
    E_MVOP_HS_NOT_SUPPORT    = 0,
    E_MVOP_HS_ENABLE         = 0x01,
    E_MVOP_HS_DISABLE        = 0x02,
    E_MVOP_HS_INVALID_PARAM = 0x03,

} MVOP_HSMode;

typedef struct
{
    MS_U32 u32Framerate;
    MS_U16 u16HSize;
    MS_U16 u16VSize;
    MS_BOOL b3DTB;
    MS_BOOL b3DSBS;
    MS_BOOL bReserve[6];
} MVOP_GetMaxFps;

typedef struct
{
    MS_U16 u16XStart;
    MS_U16 u16YStart;
    MS_U16 u16XSize;
    MS_U16 u16YSize;
    MS_U32 reserve[2];
} MVOP_XCGetCrop;

typedef struct
{
    MS_U32 u32MSBStartY0;
    MS_U32 u32MSBStartUV0;
    MS_U32 u32MSBStartY1;
    MS_U32 u32MSBStartUV1;

    MS_U32 u32LSBStartY0;
    MS_U32 u32LSBStartUV0;
    MS_U32 u32LSBStartY1;
    MS_U32 u32LSBStartUV1;
    MVOP_XCGetCrop stXCCrop;
    MS_U16 u16XCap;
    MS_U16 u16YCap;
    MS_U32 reserve[4];
    MS_U32 u32MFCodecInfo;
    MS_U32 u32LumaMFCbitlen;
    MS_U32 u32ChromaMFCbitlen;
    MS_U16 u16Pitch;
    MS_U16 u16Pitch_2bit;
} MVOP_XCGetCropMirAdd;

typedef struct
{
    float fHratio;
    float fVratio;
    float reserve0[4];
    MS_U32 reserve1[2];
} MVOP_OutputHVRatio;

//-------------------------------------------------------------------------------------------------
//  Function and Variable
//-------------------------------------------------------------------------------------------------

// Basic Function
//-------------------------------------------------------------------------------------------------
/// Initial Main MVOP.
/// @ingroup MVOP_Basic
/// @param void \b IN : void
/// @return void
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_Init (void);
//-------------------------------------------------------------------------------------------------
/// Disable Main MVOP clock.
/// @ingroup MVOP_Basic
/// @param void \b IN : void
/// @return void
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_Exit(void);
//-------------------------------------------------------------------------------------------------
/// Main MVOP power switch; start to generate timing.
/// @ingroup MVOP_Basic
/// @param MS_BOOL \b IN : enable or disable MVOP.
/// @return void
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_Enable ( MS_BOOL bEnable );
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP Input stream information and reset ex-stream status.
/// @ingroup MVOP_Basic
/// @param in \b IN : Set mvop input: Hardwire mode or MCU mode / Codec type.
/// @param pCfg \b IN : Set mvop input: MCU mode data format setting.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_SetInputCfg (MVOP_InputSel in, MVOP_InputCfg* pCfg);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP Output timing information.
/// @ingroup MVOP_Basic
/// @param pstVideoStatus \b IN : Set mvop output Timing.
/// @param bEnHDup \b IN : Is Hsize duplicated?
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_SetOutputCfg(MVOP_VidStat *pstVideoStatus, MS_BOOL bEnHDup);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP Background color as black.
/// @ingroup MVOP_Basic
/// @param void \b IN : void.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_EnableBlackBG ( void );
// SetCommand Function
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP UV forwarding one line.
/// @ingroup MVOP_SetCommand
/// @param bEnable \b IN: enable or disable.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_EnableUVShift(MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP only Luma data(Black/white feature).
/// @ingroup MVOP_SetCommand
/// @param bEnable \b IN: enable or disable.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SetMonoMode(MS_BOOL bEnable);
// GetCommand Function
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP source Width.
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return: Width.
//-------------------------------------------------------------------------------------------------
MS_U16 MDrv_MVOP_GetHSize(void);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP source Height.
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return: Height.
//-------------------------------------------------------------------------------------------------
MS_U16 MDrv_MVOP_GetVSize(void);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP the timing of xc data starting(capture win. h start).
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return: timing of data start in Htt.
//-------------------------------------------------------------------------------------------------
MS_U16 MDrv_MVOP_GetHStart(void);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP the timing of xc data starting(capture win. v start).
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return: timing of data start in Vtt.
//-------------------------------------------------------------------------------------------------
MS_U16 MDrv_MVOP_GetVStart(void);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP timing is interlace or not.
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return: true or false.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_GetIsInterlace(void);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP H data is duplicated or not.
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return: true or false.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_GetIsHDuplicate(void);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP is enable or not.
/// @ingroup MVOP_GetCommand
/// @param pbEnable \b IN : Is enable or not.
/// @return: true or false.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_GetIsEnable ( MS_BOOL* pbEnable );
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP output timing.
/// @ingroup MVOP_GetCommand
/// @param pMVOPTiming \b IN : the pointer of timing struc.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_GetOutputTiming(MVOP_Timing* pMVOPTiming);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP library version.
/// @ingroup MVOP_GetCommand
/// @param ppVersion \b IN : mvop library version no..
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_GetLibVer(const MSIF_Version **ppVersion);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP HW capability.
/// @ingroup MVOP_GetCommand
/// @param u16HSize \b IN : input height.
/// @param u16VSize \b IN : input height.
/// @param u16Fps \b IN : input framerate.
/// @return MS_BOOL: support this timing or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_CheckCapability(MS_U16 u16HSize, MS_U16 u16VSize, MS_U16 u16Fps);
//   Functions for the 3rd MVOP }
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP maximum of horizontal offset.
/// @ingroup MVOP_GetCommand
/// @param u16HSize \b IN : input height.
/// @param u16VSize \b IN : input height.
/// @param u16Fps \b IN : input framerate.
/// @return MS_BOOL: maximum of horizontal offset.
//-------------------------------------------------------------------------------------------------
MS_U16 MDrv_MVOP_GetMaxHOffset(MS_U16 u16HSize, MS_U16 u16VSize, MS_U16 u16Fps);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP maximum of vertical offset.
/// @ingroup MVOP_GetCommand
/// @param u16HSize \b IN : input height.
/// @param u16VSize \b IN : input height.
/// @param u16Fps \b IN : input framerate.
/// @return MS_BOOL: maximum of vertical offset.
//-------------------------------------------------------------------------------------------------
MS_U16 MDrv_MVOP_GetMaxVOffset(MS_U16 u16HSize, MS_U16 u16VSize, MS_U16 u16Fps);
// MVOP_Debug
//-------------------------------------------------------------------------------------------------
/// Set MVOP debug level.
/// @ingroup MVOP_SetCommand
/// @param level \b IN: level.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SetDbgLevel(MS_U8 level);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP clock infomation.
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return MVOP_DrvInfo: the pointer of clock information.
//-------------------------------------------------------------------------------------------------
// const MVOP_DrvInfo* MDrv_MVOP_GetInfo(void);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP current setting status.
/// @ingroup MVOP_GetCommand
/// @param pMVOPStat \b IN : the pointer of mvop status.
/// @return MS_BOOL: get is status successful or not.
//-------------------------------------------------------------------------------------------------
// MS_BOOL MDrv_MVOP_GetStatus(MVOP_DrvStatus *pMVOPStat);
//-------------------------------------------------------------------------------------------------
/// Set MVOP Pattern type.
/// @ingroup MVOP_SetCommand
/// @param enMVOPPattern \b IN: pattern type.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SetPattern(MVOP_Pattern enMVOPPattern);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP tile format.
/// @ingroup MVOP_SetCommand
/// @param eTileFmt \b IN: tile format.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SetTileFormat(MVOP_TileFormat eTileFmt);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP current display timing infomation from register.
/// @ingroup MVOP_GetCommand
/// @param pDstInfo \b IN : the pointer of mvop timing.
/// @param u32SizeofDstInfo \b IN : the size of pDstInfo.
/// @return MS_BOOL: get is status successful or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_GetDstInfo(MVOP_DST_DispInfo *pDstInfo, MS_U32 u32SizeofDstInfo);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP Vtt fixed.
/// @ingroup MVOP_SetCommand
/// @param u16FixVtt \b IN: Vtt.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SetFixVtt(MS_U16 u16FixVtt);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP MMIO Map base address.
/// @ingroup MVOP_SetCommand
/// @param void \b IN: void.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SetMMIOMapBase(void);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP access which miu.
/// @ingroup MVOP_Basic
/// @param u8Miu \b IN : miu 0/1/2...
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_MiuSwitch(MS_U8 u8Miu);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP MCU mode YUV address.
/// @ingroup MVOP_SetCommand
/// @param u32YOffset \b IN: Y address.
/// @param u32UVOffset \b IN: UV address.
/// @param bProgressive \b IN: Is progressive.
/// @param b422pack \b IN: Is 422 packed or not.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SetBaseAdd(MS_PHY u32YOffset, MS_PHY u32UVOffset, MS_BOOL bProgressive, MS_BOOL b422pack);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP elect output field for display one field. default: mvop t/b toggle, update one field to both t/b xc buffer.
/// @ingroup MVOP_SetCommand
/// @param void \b IN: void.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SEL_OP_FIELD(MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP hsize/vsize from vdec DIU/WB.
/// @ingroup MVOP_SetCommand
/// @param bEnable \b IN: Enable/Disable.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SetRegSizeFromMVD(MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP crop x/y start.
/// @ingroup MVOP_SetCommand
/// @param u16Xpos \b IN: x start.
/// @param u16Ypos \b IN: y start.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SetStartPos(MS_U16 u16Xpos ,MS_U16 u16Ypos);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP crop x/y size.
/// @ingroup MVOP_SetCommand
/// @param u16Width \b IN: x size.
/// @param u16Height \b IN: y size.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SetImageWidthHight(MS_U16 u16Width ,MS_U16 u16Height);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP mirror mode.
/// @ingroup MVOP_SetCommand
/// @param bEnable \b IN: enable/disable.
/// @param eMirrorMode \b IN: mirror mode type.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SetVOPMirrorMode(MS_BOOL bEnable,MVOP_DrvMirror eMirrorMode);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP output vsync inversed.
/// @ingroup MVOP_SetCommand
/// @param bEnable \b IN: enable/disable.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_INV_OP_VS(MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP output only top field.
/// @ingroup MVOP_SetCommand
/// @param bEnable \b IN: enable/disable.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_FORCE_TOP(MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP enable freerun mode.
/// @ingroup MVOP_SetCommand
/// @param bEnable \b IN: enable/disable.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_EnableFreerunMode(MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP cuurent frame base address(MCU mode only).
/// @ingroup MVOP_GetCommand
/// @param u32YOffset \b IN : the pointer of Luma address.
/// @param u32UVOffset \b IN : the pointer of Chroma address.
/// @return void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_GetBaseAdd(MS_PHY* u32YOffset, MS_PHY* u32UVOffset);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP current setting status.
/// @ingroup MVOP_GetCommand
/// @param pMVOPStat \b IN : the pointer of mvop status.
/// @return MS_BOOL: get is status successful or not.
//-------------------------------------------------------------------------------------------------
// MS_BOOL MDrv_MVOP_SubGetStatus(MVOP_DrvStatus *pMVOPStat);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP the timing of xc data starting(capture win. h start).
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return: timing of data start in Htt.
//-------------------------------------------------------------------------------------------------
MS_U16 MDrv_MVOP_SubGetHStart(void);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP the timing of xc data starting(capture win. v start).
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return: timing of data start in Vtt.
//-------------------------------------------------------------------------------------------------
MS_U16 MDrv_MVOP_SubGetVStart(void);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP Pattern type.
/// @ingroup MVOP_SetCommand
/// @param enMVOPPattern \b IN: pattern type.
/// @return: void.
//-------------------------------------------------------------------------------------------------
// void MDrv_MVOP_SubSetPattern(MVOP_Pattern enMVOPPattern);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP tile format.
/// @ingroup MVOP_SetCommand
/// @param eTileFmt \b IN: tile format.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SubSetTileFormat(MVOP_TileFormat eTileFmt);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP MMIO Map base address.
/// @ingroup MVOP_SetCommand
/// @param void \b IN: void.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
// MS_BOOL MDrv_MVOP_SubSetMMIOMapBase(void);
//-------------------------------------------------------------------------------------------------
/// Initial Sub MVOP.
/// @ingroup MVOP_Basic
/// @param void \b IN : void
/// @return void
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SubInit(void);
//-------------------------------------------------------------------------------------------------
/// Disable Sub MVOP clock.
/// @ingroup MVOP_Basic
/// @param void \b IN : void
/// @return void
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SubExit(void);
//-------------------------------------------------------------------------------------------------
/// Sub MVOP power switch; start to generate timing.
/// @ingroup MVOP_Basic
/// @param MS_BOOL \b IN : enable or disable MVOP.
/// @return void
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SubEnable(MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP is enable or not.
/// @ingroup MVOP_GetCommand
/// @param pbEnable \b IN : Is enable or not.
/// @return: true or false.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_SubGetIsEnable (MS_BOOL* pbEnable);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP UV forwarding one line.
/// @ingroup MVOP_SetCommand
/// @param bEnable \b IN: enable or disable.
/// @return: void.
//-------------------------------------------------------------------------------------------------
// void MDrv_MVOP_SubEnableUVShift(MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP Background color as black.
/// @ingroup MVOP_Basic
/// @param void \b IN : void.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SubEnableBlackBG(void);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP only Luma data(Black/white feature).
/// @ingroup MVOP_SetCommand
/// @param bEnable \b IN: enable or disable.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SubSetMonoMode(MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP Input stream information and reset ex-stream status.
/// @ingroup MVOP_Basic
/// @param in \b IN : Set mvop input: Hardwire mode or MCU mode / Codec type.
/// @param pCfg \b IN : Set mvop input: MCU mode data format setting.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_SubSetInputCfg (MVOP_InputSel in, MVOP_InputCfg* pCfg);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP Output timing information.
/// @ingroup MVOP_Basic
/// @param pstVideoStatus \b IN : Set mvop output Timing.
/// @param bEnHDup \b IN : Is Hsize duplicated?
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_SubSetOutputCfg(MVOP_VidStat *pstVideoStatus, MS_BOOL bEnHDup);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP output timing.
/// @ingroup MVOP_GetCommand
/// @param pMVOPTiming \b IN : the pointer of timing struc.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_SubGetOutputTiming(MVOP_Timing* pMVOPTiming);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP source Width.
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return: Width.
//-------------------------------------------------------------------------------------------------
MS_U16 MDrv_MVOP_SubGetHSize(void);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP source Height.
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return: Height.
//-------------------------------------------------------------------------------------------------
MS_U16 MDrv_MVOP_SubGetVSize(void);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP timing is interlace or not.
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return: true or false.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SubGetIsInterlace(void);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP H data is duplicated or not.
/// @ingroup MVOP_GetCommand
/// @param void \b IN : void.
/// @return: true or false.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SubGetIsHDuplicate(void);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP HW capability.
/// @ingroup MVOP_GetCommand
/// @param u16HSize \b IN : input height.
/// @param u16VSize \b IN : input height.
/// @param u16Fps \b IN : input framerate.
/// @return MS_BOOL: support this timing or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SubCheckCapability(MS_U16 u16HSize, MS_U16 u16VSize, MS_U16 u16Fps);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP maximum of horizontal offset.
/// @ingroup MVOP_GetCommand
/// @param u16HSize \b IN : input height.
/// @param u16VSize \b IN : input height.
/// @param u16Fps \b IN : input framerate.
/// @return MS_BOOL: maximum of horizontal offset.
//-------------------------------------------------------------------------------------------------
MS_U16 MDrv_MVOP_SubGetMaxHOffset(MS_U16 u16HSize, MS_U16 u16VSize, MS_U16 u16Fps);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP maximum of vertical offset.
/// @ingroup MVOP_GetCommand
/// @param u16HSize \b IN : input height.
/// @param u16VSize \b IN : input height.
/// @param u16Fps \b IN : input framerate.
/// @return MS_BOOL: maximum of vertical offset.
//-------------------------------------------------------------------------------------------------
MS_U16 MDrv_MVOP_SubGetMaxVOffset(MS_U16 u16HSize, MS_U16 u16VSize, MS_U16 u16Fps);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP current display timing infomation from register.
/// @ingroup MVOP_GetCommand
/// @param pDstInfo \b IN : the pointer of mvop timing.
/// @param u32SizeofDstInfo \b IN : the size of pDstInfo.
/// @return MS_BOOL: get is status successful or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SubGetDstInfo(MVOP_DST_DispInfo *pDstInfo, MS_U32 u32SizeofDstInfo);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP Vtt fixed.
/// @ingroup MVOP_SetCommand
/// @param u16FixVtt \b IN: Vtt.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SubSetFixVtt(MS_U16 u16FixVtt);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP access which miu.
/// @ingroup MVOP_Basic
/// @param u8Miu \b IN : miu 0/1/2...
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_SubMiuSwitch(MS_U8 u8Miu);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP mirror mode.
/// @ingroup MVOP_SetCommand
/// @param bEnable \b IN: enable/disable.
/// @param eMirrorMode \b IN: mirror mode type.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SubSetVOPMirrorMode(MS_BOOL bEnable, MVOP_DrvMirror eMirrorMode);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP enable freerun mode.
/// @ingroup MVOP_SetCommand
/// @param bEnable \b IN: enable/disable.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SubEnableFreerunMode(MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Set Sub MVOP MCU mode YUV address.
/// @ingroup MVOP_SetCommand
/// @param u32YOffset \b IN: Y address.
/// @param u32UVOffset \b IN: UV address.
/// @param bProgressive \b IN: Is progressive.
/// @param b422pack \b IN: Is 422 packed or not.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
MS_BOOL MDrv_MVOP_SubSetBaseAdd(MS_PHY u32YOffset, MS_PHY u32UVOffset, MS_BOOL bProgressive, MS_BOOL b422pack);
//-------------------------------------------------------------------------------------------------
/// Get Sub MVOP cuurent frame base address(MCU mode only).
/// @ingroup MVOP_GetCommand
/// @param u32YOffset \b IN : the pointer of Luma address.
/// @param u32UVOffset \b IN : the pointer of Chroma address.
/// @return void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SubGetBaseAdd(MS_PHY* u32YOffset, MS_PHY* u32UVOffset);

//-------------------------------------------------------------------------------------------------
/// Initial Extended MVOP.
/// @ingroup MVOP_Basic
/// @param eID \b IN : Device ID.
/// @param void \b IN : void.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_Init(MVOP_DevID eID, MS_U32 u32InitParam);
//-------------------------------------------------------------------------------------------------
/// Disable Extended  MVOP clock.
/// @ingroup MVOP_Basic
/// @param eID \b IN : Device ID.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_Exit(MVOP_DevID eID, MS_U32 u32ExitParam);
//-------------------------------------------------------------------------------------------------
/// Extended MVOP power switch; start to generate timing.
/// @ingroup MVOP_Basic
/// @param eID \b IN : Device ID.
/// @param MS_BOOL \b IN : enable or disable MVOP.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_Enable(MVOP_DevID eID, MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Set Extended  MVOP Input stream information and reset ex-stream status.
/// @ingroup MVOP_Basic
/// @param eID \b IN : Device ID.
/// @param in \b IN : Set mvop input: Hardwire mode or MCU mode / Codec type.
/// @param pCfg \b IN : Set mvop input: MCU mode data format setting.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_SetInputCfg (MVOP_DevID eID, MVOP_InputSel in, MVOP_InputCfg* pCfg);
//-------------------------------------------------------------------------------------------------
/// Set Extended  MVOP Output timing information.
/// @ingroup MVOP_Basic
/// @param eID \b IN : Device ID.
/// @param pstVideoStatus \b IN : Set mvop output Timing.
/// @param bEnHDup \b IN : Is Hsize duplicated?
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_SetOutputCfg(MVOP_DevID eID, MVOP_VidStat *pstVideoStatus, MS_BOOL bEnHDup);

//-------------------------------------------------------------------------------------------------
/// Set Extended MVOP Pattern type.
/// @ingroup MVOP_SetCommand
/// @param eID \b IN : Device ID.
/// @param enMVOPPattern \b IN: pattern type.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_SetPattern(MVOP_DevID eID, MVOP_Pattern enMVOPPattern);
//-------------------------------------------------------------------------------------------------
/// Set Extended MVOP tile format.
/// @ingroup MVOP_SetCommand
/// @param eID \b IN : Device ID.
/// @param eTileFmt \b IN: tile format.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_SetTileFormat(MVOP_DevID eID, MVOP_TileFormat eTileFmt);
//-------------------------------------------------------------------------------------------------
/// Set Extended MVOP UV forwarding one line.
/// @ingroup MVOP_SetCommand
/// @param eID \b IN : Device ID.
/// @param bEnable \b IN: enable or disable.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_EnableUVShift(MVOP_DevID eID, MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Set Extended MVOP Background color as black.
/// @ingroup MVOP_Basic
/// @param eID \b IN : Device ID.
/// @param void \b IN : void.
/// @return: void.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_EnableBlackBG(MVOP_DevID eID);
//-------------------------------------------------------------------------------------------------
/// Set Extended MVOP only Luma data(Black/white feature).
/// @ingroup MVOP_SetCommand
/// @param eID \b IN : Device ID.
/// @param bEnable \b IN: enable or disable.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_SetMonoMode(MVOP_DevID eID, MS_BOOL bEnable);
//-------------------------------------------------------------------------------------------------
/// Set Extended MVOP Vtt fixed.
/// @ingroup MVOP_SetCommand
/// @param eID \b IN : Device ID.
/// @param u16FixVtt \b IN: Vtt.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_SetFixVtt(MVOP_DevID eID, MS_U16 u16FixVtt);
//-------------------------------------------------------------------------------------------------
/// Set Extended MVOP access which miu.
/// @ingroup MVOP_Basic
/// @param eID \b IN : Device ID.
/// @param u8Miu \b IN : miu 0/1/2...
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_MiuSwitch(MVOP_DevID eID, MS_U8 u8Miu);
//-------------------------------------------------------------------------------------------------
/// Set Extended MVOP mirror mode.
/// @ingroup MVOP_SetCommand
/// @param eID \b IN : Device ID.
/// @param bEnable \b IN: enable/disable.
/// @param eMirrorMode \b IN: mirror mode type.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_SetVOPMirrorMode(MVOP_DevID eID, MS_BOOL bEnable, MVOP_DrvMirror eMirrorMode);
//-------------------------------------------------------------------------------------------------
/// Set Extended MVOP enable freerun mode.
/// @ingroup MVOP_SetCommand
/// @param eID \b IN : Device ID.
/// @param bEnable \b IN: enable/disable.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_EnableFreerunMode(MVOP_DevID eID, MS_BOOL bEnable);

//-------------------------------------------------------------------------------------------------
/// Get Extended MVOP output timing.
/// @ingroup MVOP_GetCommand
/// @param eID \b IN : Device ID.
/// @param pMVOPTiming \b IN : the pointer of timing struc.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_GetOutputTiming(MVOP_DevID eID, MVOP_Timing* pMVOPTiming);
//-------------------------------------------------------------------------------------------------
/// Get Extended MVOP is enable or not.
/// @ingroup MVOP_GetCommand
/// @param eID \b IN : Device ID.
/// @param pbEnable \b IN : Is enable or not.
/// @return: true or false.
//-------------------------------------------------------------------------------------------------
// MVOP_Result MDrv_MVOP_EX_GetIsEnable (MVOP_DevID eID, MS_BOOL* pbEnable);
//-------------------------------------------------------------------------------------------------
/// Get Extended MVOP the timing of xc data starting(capture win. h start).
/// @ingroup MVOP_GetCommand
/// @param eID \b IN : Device ID.
/// @param void \b IN : void.
/// @return: timing of data start in Htt.
//-------------------------------------------------------------------------------------------------
// MS_U16 MDrv_MVOP_EX_GetHStart(MVOP_DevID eID);
//-------------------------------------------------------------------------------------------------
/// Get Extended MVOP the timing of xc data starting(capture win. v start).
/// @ingroup MVOP_GetCommand
/// @param eID \b IN : Device ID.
/// @param void \b IN : void.
/// @return: timing of data start in Vtt.
//-------------------------------------------------------------------------------------------------
// MS_U16 MDrv_MVOP_EX_GetVStart(MVOP_DevID eID);
//-------------------------------------------------------------------------------------------------
/// Get Extended MVOP source Width.
/// @ingroup MVOP_GetCommand
/// @param eID \b IN : Device ID.
/// @param void \b IN : void.
/// @return: Width.
//-------------------------------------------------------------------------------------------------
// MS_U16 MDrv_MVOP_EX_GetHSize(MVOP_DevID eID);
//-------------------------------------------------------------------------------------------------
/// Get Extended MVOP source Height.
/// @ingroup MVOP_GetCommand
/// @param eID \b IN : Device ID.
/// @param void \b IN : void.
/// @return: Height.
//-------------------------------------------------------------------------------------------------
// MS_U16 MDrv_MVOP_EX_GetVSize(MVOP_DevID eID);
//-------------------------------------------------------------------------------------------------
/// Get Extended MVOP timing is interlace or not.
/// @ingroup MVOP_GetCommand
/// @param eID \b IN : Device ID.
/// @param void \b IN : void.
/// @return: true or false.
//-------------------------------------------------------------------------------------------------
// MS_BOOL MDrv_MVOP_EX_GetIsInterlace(MVOP_DevID eID);
//-------------------------------------------------------------------------------------------------
/// Get Extended MVOP H data is duplicated or not.
/// @ingroup MVOP_GetCommand
/// @param eID \b IN : Device ID.
/// @param void \b IN : void.
/// @return: true or false.
//-------------------------------------------------------------------------------------------------
// MS_BOOL MDrv_MVOP_EX_GetIsHDuplicate(MVOP_DevID eID);
//-------------------------------------------------------------------------------------------------
/// Get Extended MVOP current setting status.
/// @ingroup MVOP_GetCommand
/// @param eID \b IN : Device ID.
/// @param pMVOPStat \b IN : the pointer of mvop status.
/// @return MS_BOOL: get is status successful or not.
//-------------------------------------------------------------------------------------------------
// MS_BOOL MDrv_MVOP_EX_GetStatus(MVOP_DevID eID, MVOP_DrvStatus *pMVOPStat);
#if defined (__aarch64__)
// MS_BOOL MDrv_MVOP_EX_CheckCapability(MVOP_DevID eID, MS_U64 u32InParam);
#else
//-------------------------------------------------------------------------------------------------
/// Get Extended MVOP HW capability.
/// @ingroup MVOP_GetCommand
/// @param eID \b IN : Device ID.
/// @param u16HSize \b IN : input height.
/// @param u16VSize \b IN : input height.
/// @param u16Fps \b IN : input framerate.
/// @return MS_BOOL: support this timing or not.
//-------------------------------------------------------------------------------------------------
// MS_BOOL MDrv_MVOP_EX_CheckCapability(MVOP_DevID eID, MS_U32 u32InParam);
#endif
// MS_BOOL MDrv_MVOP_EX_GetDstInfo(MVOP_DevID eID, MVOP_DST_DispInfo *pDstInfo, MS_U32 u32SizeofDstInfo);
//   Functions for the 3rd MVOP }
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP enable freerun mode.
/// @ingroup MVOP_SetCommand
/// @param bEnable \b IN: enable/disable.
/// @return: MS_BOOL: setting successfully or not.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_SendBlueScreen(MS_U16 u16Width, MS_U16 u16Height);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP by command.
/// @ingroup MVOP_SetCommand
/// @param stHd \b IN: device id(main/sub..).
/// @param eCmd \b IN: command enum.
/// @param pPara \b IN: command parameters.
/// @return: void.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_SetCommand(MVOP_Handle* stHd, MVOP_Command eCmd, void* pPara);
//-------------------------------------------------------------------------------------------------
/// Get Main MVOP information by command.
/// @ingroup MVOP_GetCommand
/// @param stHd \b IN : Devide ID(main mvop or sub).
/// @param eCmd \b IN : command enum.
/// @param pPara \b IN : command parameters.
/// @param u32ParaSize \b IN : size of Parameter structure.
/// @return MVOP_Result
///     - E_MVOP_OK: success
///     - E_MVOP_FAIL: failed
///     - E_MVOP_INVALID_PARAM: input param error.
///     - E_MVOP_NOT_INIT: not initialized yet.
///     - E_MVOP_UNSUPPORTED: input case not support.
//-------------------------------------------------------------------------------------------------
MVOP_Result MDrv_MVOP_GetCommand(MVOP_Handle* stHd, MVOP_Command eCmd, void* pPara, MS_U32 u32ParaSize);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP output clock.
/// @ingroup MVOP_SetCommand
/// @param eFreq \b IN: clock.
/// @return: void.
//-------------------------------------------------------------------------------------------------
void MDrv_MVOP_SetFrequency(MVOP_FREQUENCY eFreq);
//-------------------------------------------------------------------------------------------------
/// Set Main MVOP STR command.
/// @ingroup MVOP_Basic
/// @param u16PowerState \b IN : command of STR(resume/suspend)
/// @return MS_U32: utopia status.
//-------------------------------------------------------------------------------------------------
MS_U32 MDrv_MVOP_SetPowerState(EN_POWER_MODE u16PowerState);
#ifdef __cplusplus
}
#endif

#endif // _DRV_MVOP_H_