1# RV1106 Release Note 2 3## rv1106_ddr_924MHz{_tb}_v1.11.bin 4 5| Date | File | Build commit | Severity | 6| ---------- | :------------------------------- | ------------ | --------- | 7| 2023-03-28 | rv1106_ddr_924MHz{_tb}_v1.11.bin | 285bced5c1 | important | 8 9### Fixed 10 11| Index | Severity | Update | Issue description | Issue source | 12| ----- | --------- | -------------------------- | ---------------------------------------- | ------------ | 13| 1 | important | Change DDR3 CLK drv of QFN | DDR may be unstable in certain scenarios | - | 14 15------ 16 17## rv1106_hpmcu_tb_{sc230ai,sc3338,gc3003,sc4336,dual_sc3338}_v1.63.bin 18 19| Date | File | Build commit | Severity | 20| ---------- | :----------------------------------------------------------- | ---------------------------------------------- | -------- | 21| 2023-03-24 | rv1106_hpmcu_tb_{sc230ai,sc3338,gc3003,sc4336,dual_sc3338}_v1.63.bin | rtt:c6b03745b#hal:d93ef9fd#battery_ipc:f52bf08 | critical | 22 23### New 24 251. Add dual sc3338 camera driver support. 262. Support to get DPHY, VICAP, CSI2HOST device info from board config. 273. Support dual camera fastboot. 28 29------ 30 31## rv1106_hpmcu_tb_gc2093_v1.63.bin 32 33| Date | File | Build commit | Severity | 34| ---------- | :------------------------------------------------------- | ------------------------------------------------ | -------- | 35| 2023-03-07 | rv1106_hpmcu_tb_gc2093_v1.63.bin | rtt:831ea1368#hal:d93ef9fd#battery_ipc:12d4661 | important | 36 37### New 38 391. Gc2093 add 1920x1080@25fps 27M mclk. 40 41------ 42 43## rv1106_hpmcu_tb_gc2093_v1.62.bin 44 45| Date | File | Build commit | Severity | 46| ---------- | :------------------------------------------------------- | ---------------------------------------------- | --------- | 47| 2023-02-16 | rv1106_hpmcu_tb_gc2093_v1.62.bin | rtt:5a5a088d0#hal:d93ef9fd#battery_ipc:12d4661 | critical | 48 49### New 50 511. Fast ae supports up to 20 frames as default. 522. Add IR/white light mode support. 533. Add support for nonlinear single range ADC. 544. Add support for soft light sensor. 555. Supports the configuration of fast ae run frame number. 56 57### Fixed 58 59| 1 | critical | Limit camera convergence time. | Camera spends too much time converging，it causes the thunderboot isp driver in kernel fails to start stream. | - | 60| 2 | critical | Fixed repeated ircut and light Settings. | Under analog light sensor, after setting night mode to 3/4, ircut and light will be set again in frame 6. | - | 61| 1 | critical | In the soft light sensor scheme, the fastae converges before the fill light is stabilized in the night vision mode | Fastae converges before the fill light is stabilized in night vision mode, resulting in abnormal exposure. | - | 62 63------ 64 65## rv1106_hpmcu_tb_{sc230ai,sc3338,gc3003,sc4336}_v1.62.bin 66 67| Date | File | Build commit | Severity | 68| ---------- | :------------------------------------------------------- | ---------------------------------------------- | --------- | 69| 2023-02-01 | rv1106_hpmcu_tb_{sc230ai,sc3338,gc3003,sc4336}_v1.62.bin | rtt:5a5a088d0#hal:d93ef9fd#battery_ipc:12d4661 | critical | 70 71### Fixed 72 73| Index | Severity | Update | Issue source | Issue | 74| ----- | --------- | ------------------------------------------------------------ | ------------------------------------------------------------ | ----- | 75| 1 | critical | In the soft light sensor scheme, the fastae converges before the fill light is stabilized in the night vision mode | Fastae converges before the fill light is stabilized in night vision mode, resulting in abnormal exposure. | - | 76 77------ 78 79## rv1106_hpmcu_wrap_v1.54.bin 80 81| Date | File | Build commit | Severity | 82| ---------- | :-------------------------- | ------------------------------- | -------- | 83| 2023-1-15 | rv1106_hpmcu_wrap_v1.54.bin | rockit_ko:69d42563#hal:a76806e7 | important | 84 85### Fixed 86 87| Index | Severity | Update | Issue source | Issue | 88| ----- | --------- | --------------------------- | --------------------------------- | -------- | 89| 1 | important | Increase the monitoring conditions of wrap OVERFLOW | image tear possiable | - | 90 91------ 92 93## rv1106_hpmcu_tb_{sc230ai,sc3338,gc3003,sc4336}_v1.61.bin 94 95| Date | File | Build commit | Severity | 96| ---------- | :------------------------------------------------------- | ---------------------------------------------- | -------- | 97| 2023-01-05 | rv1106_hpmcu_tb_{sc230ai,sc3338,gc3003,sc4336}_v1.61.bin | rtt:5a5a088d0#hal:d93ef9fd#battery_ipc:dacbbc1 | critical | 98 99### Fixed 100 101| Index | Severity | Update | Issue description | Issue source | 102| ----- | -------- | ---------------------------------------- | ------------------------------------------------------------ | ------------ | 103| 1 | critical | Fixed the gc3003 pre-opening problem. | If sensor stream on advanced，isp will met dqbuf sem failed error. | - | 104| 2 | critical | Fixed repeated ircut and light Settings. | Under analog light sensor, after setting night mode to 3/4, ircut and light will be set again in frame 6. | - | 105 106------ 107 108## rv1106_hpmcu_tb_{sc230ai,sc3338,gc3003,sc4336}_v1.60.bin 109| Date | File | build commit | Severity | 110| ---------- | :------------------------------------------------------- | ------------------------------------------------ | -------- | 111| 2022-12-22 | rv1106_hpmcu_tb_{sc230ai,sc3338,gc3003,sc4336}_v1.60.bin | rtt:755701b24#hal:d93ef9fd#battery_ipc:18df679ea | critical | 112 113### New 114 1151. Add sc4336 support. 1162. Fast ae supports up to 20 frames as default. 1173. Add IR/white light mode support. 1184. Add support for nonlinear single range ADC. 1195. Add support for soft light sensor. 1206. Supports the configuration of fast ae run frame number. 121 122### Fixed 123 124| Index | Severity | Update | Issue description | Issue source | 125| ----- | -------- | ------------------------------------- | ------------------------------------------------------------ | ------------ | 126| 1 | critical | Fixed the gc3003 pre-opening problem. | If sensor stream on advanced，isp will met dqbuf sem failed error. | - | 127 128------ 129 130## rv1106_hpmcu_tb_{sc230ai,sc3338,gc3003}_v1.50.bin 131 132| Date | File | Build commit | Severity | 133| ---------- | :------------------------------------------------ | ------------------------------------------- | -------- | 134| 2022-11-17 | rv1106_hpmcu_tb_{sc230ai,sc3338,gc3003}_v1.50.bin | rtt:a40f17d#hal:b569247#battery_ipc:c62dd55 | critical | 135 136### New 137 1381. Sc3338 add 1152x648@60fps 27M mclk bining config，chose this config as default. 1392. Add gc3003 sensor support. 140 141### Fixed 142 143| Index | Severity | Update | Issue description | Issue source | 144| ----- | -------- | ------------------------------ | ------------------------------------------------------------ | ------------ | 145| 1 | critical | Limit camera convergence time. | Camera spends too much time converging，it causes the thunderboot isp driver in kernel fails to start stream. | - | 146 147------ 148 149## rv1106_hpmcu_wrap_v1.53.bin 150 151| Date | File | Build commit | Severity | 152| ---------- | :-------------------------- | ------------------------------- | -------- | 153| 2022-11-16 | rv1106_hpmcu_wrap_v1.53.bin | rockit_ko:c9653fe9#hal:a76806e7 | important | 154 155### Fixed 156 157| Index | Severity | Update | Issue source | Issue | 158| ----- | --------- | --------------------------- | --------------------------------- | -------- | 159| 1 | important | adjust QOS policy | ISP probabilistic mipi drop frame | - | 160| 2 | important | stop the mcu when rebooting | probabilistic stuck during reboot | - | 161 162------ 163 164## rv1106_ddr_924MHz{_tb}_v1.10.bin 165 166| Date | File | Build commit | Severity | 167| ---------- | :------------------------------- | ------------ | --------- | 168| 2022-11-15 | rv1106_ddr_924MHz{_tb}_v1.10.bin | ec2fae0c96 | important | 169 170### Fixed 171 172| Index | Severity | Update | Issue description | Issue source | 173| ----- | --------- | --------------------------------------------------- | --------------------------------------------------- | ------------ | 174| 1 | important | Change reg_fb1xclk_invdelaysel_dqcmd（except DDR2） | DDR may be unstable under specific freq and voltage | - | 175| 2 | moderate | Improve write trian pattern | Improve the accuracy of write train | - | 176 177------ 178 179## rv1106_hpmcu_tb_{sc230ai,sc3338}_v1.40.bin 180 181| Date | File | Build commit | Severity | 182| --------- | :----------------------------------------- | ---------------------------------------------- | --------- | 183| 2022-11-1 | rv1106_hpmcu_tb_{sc230ai,sc3338}_v1.40.bin | rtt:05d3e965d#hal:b569247c#battery_ipc:bc3785d | important | 184 185### Fixed 186 187| Index | Severity | Update | Issue description | Issue source | 188| ----- | --------- | ------------------------------------------------------- | ------------------------------------------------ | ------------ | 189| 1 | important | Fixed sc3338 horizontal stripes when in dark brightness | sc3338 has horizontal stripes in dark brightness | - | 190 191------ 192## rv1106_hpmcu_tb_gc2093_v1.30.bin 193 194| Date | File | Build commit | Severity | 195| ---------- | :------------------------------- | ------------------------------------------------------------ | -------- | 196| 2022-10-27 | rv1106_hpmcu_tb_gc2093_v1.30.bin | rtt:2ede82a43#hal:b569247c#battery_ipc:efaec692c#rtt-cherry-pick:8b1555259 | important | 197 198### New 199 2001. Add gc2093 sensor support. 201 202------ 203## rv1106_hpmcu_tb_{sc230ai,sc3338}_v1.30.bin 204 205| Date | File | Build Commit | Severity | 206| ---------- | :----------------------------------------- | ------------------------------------------------ | -------- | 207| 2022-10-20 | rv1106_hpmcu_tb_{sc230ai,sc3338}_v1.30.bin | rtt:2ede82a43#hal:b569247c#battery_ipc:efaec692c | important | 208 209### New 210 2111. Add support for LTR308 digital light sensor. 2122. Add support for hdr. 213 214### Fixed 215 216| Index | Severity | Update | Issue description | Issue source | 217| ----- | --------- | ------------------------------------- | ------------------------------------------------------------ | ------------ | 218| 1 | important | Fixed 0 address flushed | When the spi nor flash is in 1-wire mode, spl data is flushed, so spl cannot be started. | - | 219| 2 | important | Fix the shared memory cache operation | The ARM core cannot obtain the shared memory data in time. | - | 220 221------ 222## rv1106_hpmcu_wrap_v1.50.bin 223 224| Date | File | Build commit | Severity | 225| ---------- | :-------------------------- | ------------------------------- | -------- | 226| 2022-09-29 | rv1106_hpmcu_wrap_v1.50.bin | rockit_ko:576377cb#hal:a76806e7 | critical | 227 228### Fixed 229 230| Index | Severity | Update | Issue description | Issue source | 231| ----- | --------- | -------------------------- | ------------------------------------------ | ------------ | 232| 1 | moderate | optimize code | decrease code size and add log information | - | 233| 2 | important | increase encoder ddr qos | slove some wrap overflow | - | 234| 3 | critical | invalite icache and dcache | destory linux memory for cache exchange | - | 235 236------ 237 238## rv1106_hpmcu_wrap_v1.46.bin 239 240| Date | File | Build commit | Severity | 241| ---------- | :-------------------------- | ------------------------------- | --------- | 242| 2022-09-08 | rv1106_hpmcu_wrap_v1.46.bin | rockit_ko:7e8fe8af#hal:a76806e7 | important | 243 244### Fixed 245 246| Index | Severity | Update | Issue description | Issue source | 247| ----- | --------- | --------------------------------------------------------- | ------------------------------------------------------------ | ------------ | 248| 1 | important | repair the bug of v1.40 cause | after venc start double stream，mcu maube can not check wrap frame end，casuse main stream off | - | 249| 2 | important | repair the bug destory memory when reset working mcu | when mcu is working, if it is reset will destory system memory | - | 250| 3 | important | mcu check overflow, bug venc can not lost the error frame | if venc start too slow, mcu will make a overflow event to venc, but venc can not lost the error frame | - | 251 252------ 253 254## rv1106_hpmcu_tb_{sc230ai,sc3338}_v1.20.bin 255 256| Date | File | Build Commit | Severity | 257| ---------- | :-------------------------------- | ---------- | --------- | 258| 2022-09-03 | rv1106_hpmcu_tb_{sc230ai,sc3338}_v1.20.bin | rtt:efa791c#hal:b569247#battery_ipc:d5fb92e | critical | 259 260### New 261 2621. Support full parameters in aiq for the first frame in fastboot. 2632. Support set resolution and fps from meta partition. 2643. Support sync meta header file. 2654. Optimize the iq result for fast AE,The exposure decomposition is exactly consistent with aiq, supports DB gain synsensor, and supports the check exposure register. 2665. Enable AE statistics in full-parameter parallel solution. 2676. Meta addresses can be configured using menuconfig. 268 269### Fixed 270 271| Index | Severity | Update | Issue description | Issue source | 272| ----- | --------- | ------------------------------------------------------------ | ------------------------------------------------------------ | ------------ | 273| 1 | important | resolve "thread:tidle stack overflow" problem | Sometimes "Thread: Tidle Stack Overflow" is displayed. RTT exits abnormally | - | 274| 2 | important | Suppore get AE calibration parameters from iq bin | AE calibration data is not vaild. | - | 275| 3 | important | To solve the problem of the change of denoising and sharpening effect and the dimming of brightness after AIQ startup in dark environment | The connection between kernel phase and aiq is not smooth in dark environment | - | 276| 4 | critical | To solve the problem of full-parameter image effect, it needs to match the AIQ submission 0ed3f415d3, otherwise the image will turn green | the image effect is abnormal in full-parameter | - | 277