1 /* 2 * Copyright 2011, Marvell Semiconductor Inc. 3 * Lei Wen <leiwen@marvell.com> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 * 7 * Back ported to the 8xx platform (from the 8260 platform) by 8 * Murray.Jensen@cmst.csiro.au, 27-Jan-01. 9 */ 10 #ifndef __SDHCI_HW_H 11 #define __SDHCI_HW_H 12 13 #include <asm/io.h> 14 #include <mmc.h> 15 #include <asm/gpio.h> 16 17 /* 18 * Controller registers 19 */ 20 21 #define SDHCI_DMA_ADDRESS 0x00 22 23 #define SDHCI_BLOCK_SIZE 0x04 24 #define SDHCI_MAKE_BLKSZ(dma, blksz) (((dma & 0x7) << 12) | (blksz & 0xFFF)) 25 26 #define SDHCI_BLOCK_COUNT 0x06 27 28 #define SDHCI_ARGUMENT 0x08 29 30 #define SDHCI_TRANSFER_MODE 0x0C 31 #define SDHCI_TRNS_DMA BIT(0) 32 #define SDHCI_TRNS_BLK_CNT_EN BIT(1) 33 #define SDHCI_TRNS_ACMD12 BIT(2) 34 #define SDHCI_TRNS_READ BIT(4) 35 #define SDHCI_TRNS_MULTI BIT(5) 36 37 #define SDHCI_COMMAND 0x0E 38 #define SDHCI_CMD_RESP_MASK 0x03 39 #define SDHCI_CMD_CRC 0x08 40 #define SDHCI_CMD_INDEX 0x10 41 #define SDHCI_CMD_DATA 0x20 42 #define SDHCI_CMD_ABORTCMD 0xC0 43 44 #define SDHCI_CMD_RESP_NONE 0x00 45 #define SDHCI_CMD_RESP_LONG 0x01 46 #define SDHCI_CMD_RESP_SHORT 0x02 47 #define SDHCI_CMD_RESP_SHORT_BUSY 0x03 48 49 #define SDHCI_MAKE_CMD(c, f) (((c & 0xff) << 8) | (f & 0xff)) 50 #define SDHCI_GET_CMD(c) ((c>>8) & 0x3f) 51 52 #define SDHCI_RESPONSE 0x10 53 54 #define SDHCI_BUFFER 0x20 55 56 #define SDHCI_PRESENT_STATE 0x24 57 #define SDHCI_CMD_INHIBIT BIT(0) 58 #define SDHCI_DATA_INHIBIT BIT(1) 59 #define SDHCI_DOING_WRITE BIT(8) 60 #define SDHCI_DOING_READ BIT(9) 61 #define SDHCI_SPACE_AVAILABLE BIT(10) 62 #define SDHCI_DATA_AVAILABLE BIT(11) 63 #define SDHCI_CARD_PRESENT BIT(16) 64 #define SDHCI_CARD_STATE_STABLE BIT(17) 65 #define SDHCI_CARD_DETECT_PIN_LEVEL BIT(18) 66 #define SDHCI_WRITE_PROTECT BIT(19) 67 #define SDHCI_DATA_0_LVL BIT(20) 68 69 #define SDHCI_HOST_CONTROL 0x28 70 #define SDHCI_CTRL_LED BIT(0) 71 #define SDHCI_CTRL_4BITBUS BIT(1) 72 #define SDHCI_CTRL_HISPD BIT(2) 73 #define SDHCI_CTRL_DMA_MASK 0x18 74 #define SDHCI_CTRL_SDMA 0x00 75 #define SDHCI_CTRL_ADMA1 0x08 76 #define SDHCI_CTRL_ADMA32 0x10 77 #define SDHCI_CTRL_ADMA64 0x18 78 #define SDHCI_CTRL_8BITBUS BIT(5) 79 #define SDHCI_CTRL_CD_TEST_INS BIT(6) 80 #define SDHCI_CTRL_CD_TEST BIT(7) 81 82 #define SDHCI_POWER_CONTROL 0x29 83 #define SDHCI_POWER_ON 0x01 84 #define SDHCI_POWER_180 0x0A 85 #define SDHCI_POWER_300 0x0C 86 #define SDHCI_POWER_330 0x0E 87 88 #define SDHCI_BLOCK_GAP_CONTROL 0x2A 89 90 #define SDHCI_WAKE_UP_CONTROL 0x2B 91 #define SDHCI_WAKE_ON_INT BIT(0) 92 #define SDHCI_WAKE_ON_INSERT BIT(1) 93 #define SDHCI_WAKE_ON_REMOVE BIT(2) 94 95 #define SDHCI_CLOCK_CONTROL 0x2C 96 #define SDHCI_DIVIDER_SHIFT 8 97 #define SDHCI_DIVIDER_HI_SHIFT 6 98 #define SDHCI_DIV_MASK 0xFF 99 #define SDHCI_DIV_MASK_LEN 8 100 #define SDHCI_DIV_HI_MASK 0x300 101 #define SDHCI_PROG_CLOCK_MODE BIT(5) 102 #define SDHCI_CLOCK_CARD_EN BIT(2) 103 #define SDHCI_CLOCK_INT_STABLE BIT(1) 104 #define SDHCI_CLOCK_INT_EN BIT(0) 105 106 #define SDHCI_TIMEOUT_CONTROL 0x2E 107 108 #define SDHCI_SOFTWARE_RESET 0x2F 109 #define SDHCI_RESET_ALL 0x01 110 #define SDHCI_RESET_CMD 0x02 111 #define SDHCI_RESET_DATA 0x04 112 113 #define SDHCI_INT_STATUS 0x30 114 #define SDHCI_INT_ENABLE 0x34 115 #define SDHCI_SIGNAL_ENABLE 0x38 116 #define SDHCI_INT_RESPONSE BIT(0) 117 #define SDHCI_INT_DATA_END BIT(1) 118 #define SDHCI_INT_DMA_END BIT(3) 119 #define SDHCI_INT_SPACE_AVAIL BIT(4) 120 #define SDHCI_INT_DATA_AVAIL BIT(5) 121 #define SDHCI_INT_CARD_INSERT BIT(6) 122 #define SDHCI_INT_CARD_REMOVE BIT(7) 123 #define SDHCI_INT_CARD_INT BIT(8) 124 #define SDHCI_INT_ERROR BIT(15) 125 #define SDHCI_INT_TIMEOUT BIT(16) 126 #define SDHCI_INT_CRC BIT(17) 127 #define SDHCI_INT_END_BIT BIT(18) 128 #define SDHCI_INT_INDEX BIT(19) 129 #define SDHCI_INT_DATA_TIMEOUT BIT(20) 130 #define SDHCI_INT_DATA_CRC BIT(21) 131 #define SDHCI_INT_DATA_END_BIT BIT(22) 132 #define SDHCI_INT_BUS_POWER BIT(23) 133 #define SDHCI_INT_ACMD12ERR BIT(24) 134 #define SDHCI_INT_ADMA_ERROR BIT(25) 135 136 #define SDHCI_INT_NORMAL_MASK 0x00007FFF 137 #define SDHCI_INT_ERROR_MASK 0xFFFF8000 138 139 #define SDHCI_INT_CMD_MASK (SDHCI_INT_RESPONSE | SDHCI_INT_TIMEOUT | \ 140 SDHCI_INT_CRC | SDHCI_INT_END_BIT | SDHCI_INT_INDEX) 141 #define SDHCI_INT_DATA_MASK (SDHCI_INT_DATA_END | SDHCI_INT_DMA_END | \ 142 SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL | \ 143 SDHCI_INT_DATA_TIMEOUT | SDHCI_INT_DATA_CRC | \ 144 SDHCI_INT_DATA_END_BIT | SDHCI_INT_ADMA_ERROR) 145 #define SDHCI_INT_ALL_MASK ((unsigned int)-1) 146 147 #define SDHCI_ACMD12_ERR 0x3C 148 149 /* 3E-3F reserved */ 150 #define SDHCI_HOST_CONTROL2 0x3E 151 #define SDHCI_CTRL_UHS_MASK 0x0007 152 #define SDHCI_CTRL_UHS_SDR12 0x0000 153 #define SDHCI_CTRL_UHS_SDR25 0x0001 154 #define SDHCI_CTRL_UHS_SDR50 0x0002 155 #define SDHCI_CTRL_UHS_SDR104 0x0003 156 #define SDHCI_CTRL_UHS_DDR50 0x0004 157 #define SDHCI_CTRL_HS400 0x0005 158 #define SDHCI_CTRL_VDD_180 0x0008 159 #define SDHCI_CTRL_DRV_TYPE_MASK 0x0030 160 #define SDHCI_CTRL_DRV_TYPE_B 0x0000 161 #define SDHCI_CTRL_DRV_TYPE_A 0x0010 162 #define SDHCI_CTRL_DRV_TYPE_C 0x0020 163 #define SDHCI_CTRL_DRV_TYPE_D 0x0030 164 #define SDHCI_CTRL_EXEC_TUNING 0x0040 165 #define SDHCI_CTRL_TUNED_CLK 0x0080 166 #define SDHCI_CTRL_PRESET_VAL_ENABLE 0x8000 167 168 #define SDHCI_CAPABILITIES 0x40 169 #define SDHCI_TIMEOUT_CLK_MASK 0x0000003F 170 #define SDHCI_TIMEOUT_CLK_SHIFT 0 171 #define SDHCI_TIMEOUT_CLK_UNIT 0x00000080 172 #define SDHCI_CLOCK_BASE_MASK 0x00003F00 173 #define SDHCI_CLOCK_V3_BASE_MASK 0x0000FF00 174 #define SDHCI_CLOCK_BASE_SHIFT 8 175 #define SDHCI_MAX_BLOCK_MASK 0x00030000 176 #define SDHCI_MAX_BLOCK_SHIFT 16 177 #define SDHCI_CAN_DO_8BIT BIT(18) 178 #define SDHCI_CAN_DO_ADMA2 BIT(19) 179 #define SDHCI_CAN_DO_ADMA1 BIT(20) 180 #define SDHCI_CAN_DO_HISPD BIT(21) 181 #define SDHCI_CAN_DO_SDMA BIT(22) 182 #define SDHCI_CAN_VDD_330 BIT(24) 183 #define SDHCI_CAN_VDD_300 BIT(25) 184 #define SDHCI_CAN_VDD_180 BIT(26) 185 #define SDHCI_CAN_64BIT BIT(28) 186 187 #define SDHCI_CAPABILITIES_1 0x44 188 #define SDHCI_CLOCK_MUL_MASK 0x00FF0000 189 #define SDHCI_CLOCK_MUL_SHIFT 16 190 191 #define SDHCI_MAX_CURRENT 0x48 192 193 /* 4C-4F reserved for more max current */ 194 195 #define SDHCI_SET_ACMD12_ERROR 0x50 196 #define SDHCI_SET_INT_ERROR 0x52 197 198 #define SDHCI_ADMA_ERROR 0x54 199 200 /* 55-57 reserved */ 201 202 #define SDHCI_ADMA_ADDRESS 0x58 203 204 /* 60-FB reserved */ 205 206 #define SDHCI_SLOT_INT_STATUS 0xFC 207 208 #define SDHCI_HOST_VERSION 0xFE 209 #define SDHCI_VENDOR_VER_MASK 0xFF00 210 #define SDHCI_VENDOR_VER_SHIFT 8 211 #define SDHCI_SPEC_VER_MASK 0x00FF 212 #define SDHCI_SPEC_VER_SHIFT 0 213 #define SDHCI_SPEC_100 0 214 #define SDHCI_SPEC_200 1 215 #define SDHCI_SPEC_300 2 216 217 #define SDHCI_GET_VERSION(x) (x->version & SDHCI_SPEC_VER_MASK) 218 219 /* 220 * End of controller registers. 221 */ 222 223 #define SDHCI_MAX_DIV_SPEC_200 256 224 #define SDHCI_MAX_DIV_SPEC_300 2046 225 226 /* 227 * quirks 228 */ 229 #define SDHCI_QUIRK_32BIT_DMA_ADDR (1 << 0) 230 #define SDHCI_QUIRK_REG32_RW (1 << 1) 231 #define SDHCI_QUIRK_BROKEN_R1B (1 << 2) 232 #define SDHCI_QUIRK_NO_HISPD_BIT (1 << 3) 233 #define SDHCI_QUIRK_BROKEN_VOLTAGE (1 << 4) 234 #define SDHCI_QUIRK_WAIT_SEND_CMD (1 << 6) 235 #define SDHCI_QUIRK_USE_WIDE8 (1 << 8) 236 237 /* to make gcc happy */ 238 struct sdhci_host; 239 240 /* 241 * Host SDMA buffer boundary. Valid values from 4K to 512K in powers of 2. 242 */ 243 #define SDHCI_DEFAULT_BOUNDARY_SIZE (512 * 1024) 244 #define SDHCI_DEFAULT_BOUNDARY_ARG (7) 245 struct sdhci_ops { 246 #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS 247 u32 (*read_l)(struct sdhci_host *host, int reg); 248 u16 (*read_w)(struct sdhci_host *host, int reg); 249 u8 (*read_b)(struct sdhci_host *host, int reg); 250 void (*write_l)(struct sdhci_host *host, u32 val, int reg); 251 void (*write_w)(struct sdhci_host *host, u16 val, int reg); 252 void (*write_b)(struct sdhci_host *host, u8 val, int reg); 253 #endif 254 int (*get_cd)(struct sdhci_host *host); 255 void (*set_control_reg)(struct sdhci_host *host); 256 void (*set_ios_post)(struct sdhci_host *host); 257 int (*set_clock)(struct sdhci_host *host, unsigned int clock); 258 void (*set_clock_ext)(struct sdhci_host *host, u32 div); 259 260 /** 261 * set_enhanced_strobe() - Set HS400 Enhanced Strobe config 262 * 263 * This is called after setting the card speed and mode to 264 * HS400 ES, and should set any host-specific configuration 265 * necessary for it. 266 * 267 * @host: SDHCI host structure 268 * Return: 0 if successful, -ve on error 269 */ 270 int (*set_enhanced_strobe)(struct sdhci_host *host); 271 }; 272 273 struct sdhci_host { 274 const char *name; 275 void *ioaddr; 276 unsigned int quirks; 277 unsigned int host_caps; 278 unsigned int version; 279 unsigned int max_clk; /* Maximum Base Clock frequency */ 280 unsigned int clk_mul; /* Clock Multiplier value */ 281 unsigned int clock; 282 struct mmc *mmc; 283 const struct sdhci_ops *ops; 284 int index; 285 286 int bus_width; 287 struct gpio_desc pwr_gpio; /* Power GPIO */ 288 struct gpio_desc cd_gpio; /* Card Detect GPIO */ 289 290 uint voltages; 291 292 struct mmc_config cfg; 293 }; 294 295 void sdhci_enable_clk(struct sdhci_host *host, u16 clk); 296 int sdhci_set_clock(struct sdhci_host *host, unsigned int clock); 297 298 #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS 299 300 static inline void sdhci_writel(struct sdhci_host *host, u32 val, int reg) 301 { 302 if (unlikely(host->ops->write_l)) 303 host->ops->write_l(host, val, reg); 304 else 305 writel(val, host->ioaddr + reg); 306 } 307 308 static inline void sdhci_writew(struct sdhci_host *host, u16 val, int reg) 309 { 310 if (unlikely(host->ops->write_w)) 311 host->ops->write_w(host, val, reg); 312 else 313 writew(val, host->ioaddr + reg); 314 } 315 316 static inline void sdhci_writeb(struct sdhci_host *host, u8 val, int reg) 317 { 318 if (unlikely(host->ops->write_b)) 319 host->ops->write_b(host, val, reg); 320 else 321 writeb(val, host->ioaddr + reg); 322 } 323 324 static inline u32 sdhci_readl(struct sdhci_host *host, int reg) 325 { 326 if (unlikely(host->ops->read_l)) 327 return host->ops->read_l(host, reg); 328 else 329 return readl(host->ioaddr + reg); 330 } 331 332 static inline u16 sdhci_readw(struct sdhci_host *host, int reg) 333 { 334 if (unlikely(host->ops->read_w)) 335 return host->ops->read_w(host, reg); 336 else 337 return readw(host->ioaddr + reg); 338 } 339 340 static inline u8 sdhci_readb(struct sdhci_host *host, int reg) 341 { 342 if (unlikely(host->ops->read_b)) 343 return host->ops->read_b(host, reg); 344 else 345 return readb(host->ioaddr + reg); 346 } 347 348 #else 349 350 static inline void sdhci_writel(struct sdhci_host *host, u32 val, int reg) 351 { 352 writel(val, host->ioaddr + reg); 353 } 354 355 static inline void sdhci_writew(struct sdhci_host *host, u16 val, int reg) 356 { 357 writew(val, host->ioaddr + reg); 358 } 359 360 static inline void sdhci_writeb(struct sdhci_host *host, u8 val, int reg) 361 { 362 writeb(val, host->ioaddr + reg); 363 } 364 static inline u32 sdhci_readl(struct sdhci_host *host, int reg) 365 { 366 return readl(host->ioaddr + reg); 367 } 368 369 static inline u16 sdhci_readw(struct sdhci_host *host, int reg) 370 { 371 return readw(host->ioaddr + reg); 372 } 373 374 static inline u8 sdhci_readb(struct sdhci_host *host, int reg) 375 { 376 return readb(host->ioaddr + reg); 377 } 378 #endif 379 380 #ifdef CONFIG_BLK 381 /** 382 * sdhci_setup_cfg() - Set up the configuration for DWMMC 383 * 384 * This is used to set up an SDHCI device when you are using CONFIG_BLK. 385 * 386 * This should be called from your MMC driver's probe() method once you have 387 * the information required. 388 * 389 * Generally your driver will have a platform data structure which holds both 390 * the configuration (struct mmc_config) and the MMC device info (struct mmc). 391 * For example: 392 * 393 * struct msm_sdhc_plat { 394 * struct mmc_config cfg; 395 * struct mmc mmc; 396 * }; 397 * 398 * ... 399 * 400 * Inside U_BOOT_DRIVER(): 401 * .platdata_auto_alloc_size = sizeof(struct msm_sdhc_plat), 402 * 403 * To access platform data: 404 * struct msm_sdhc_plat *plat = dev_get_platdata(dev); 405 * 406 * See msm_sdhci.c for an example. 407 * 408 * @cfg: Configuration structure to fill in (generally &plat->mmc) 409 * @host: SDHCI host structure 410 * @f_max: Maximum supported clock frequency in HZ (0 for default) 411 * @f_min: Minimum supported clock frequency in HZ (0 for default) 412 */ 413 int sdhci_setup_cfg(struct mmc_config *cfg, struct sdhci_host *host, 414 u32 f_max, u32 f_min); 415 416 /** 417 * sdhci_bind() - Set up a new MMC block device 418 * 419 * This is used to set up an SDHCI block device when you are using CONFIG_BLK. 420 * It should be called from your driver's bind() method. 421 * 422 * See msm_sdhci.c for an example. 423 * 424 * @dev: Device to set up 425 * @mmc: Pointer to mmc structure (normally &plat->mmc) 426 * @cfg: Empty configuration structure (generally &plat->cfg). This is 427 * normally all zeroes at this point. The only purpose of passing 428 * this in is to set mmc->cfg to it. 429 * @return 0 if OK, -ve if the block device could not be created 430 */ 431 int sdhci_bind(struct udevice *dev, struct mmc *mmc, struct mmc_config *cfg); 432 #else 433 434 /** 435 * add_sdhci() - Add a new SDHCI interface 436 * 437 * This is used when you are not using CONFIG_BLK. Convert your driver over! 438 * 439 * @host: SDHCI host structure 440 * @f_max: Maximum supported clock frequency in HZ (0 for default) 441 * @f_min: Minimum supported clock frequency in HZ (0 for default) 442 * @return 0 if OK, -ve on error 443 */ 444 int add_sdhci(struct sdhci_host *host, u32 f_max, u32 f_min); 445 #endif /* !CONFIG_BLK */ 446 447 #ifdef CONFIG_DM_MMC 448 /* Export the operations to drivers */ 449 int sdhci_probe(struct udevice *dev); 450 extern const struct dm_mmc_ops sdhci_ops; 451 #else 452 #endif 453 454 #endif /* __SDHCI_HW_H */ 455