xref: /rk3399_rockchip-uboot/include/lattice.h (revision 3b8ac464f25581a7d22b303a9154c05e0c7f40a8)

/*
 * Porting to U-Boot:
 *
 * (C) Copyright 2010
 * Stefano Babic, DENX Software Engineering, sbabic@denx.de.
 *
 * Lattice's ispVME Embedded Tool to load Lattice's FPGA:
 *
 * Lattice Semiconductor Corp. Copyright 2009
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 *
 */

#ifndef _VME_OPCODE_H
#define _VME_OPCODE_H

#define VME_VERSION_NUMBER "12.1"

/* Maximum declarations. */

#define VMEHEXMAX	60000L	/* The hex file is split 60K per file. */
#define SCANMAX		64000L	/* The maximum SDR/SIR burst. */

/*
 *
 * Supported JTAG state transitions.
 *
 */

#define RESET		0x00
#define IDLE		0x01
#define IRPAUSE		0x02
#define DRPAUSE		0x03
#define SHIFTIR		0x04
#define SHIFTDR		0x05
/* 11/15/05 Nguyen changed to support DRCAPTURE*/
#define DRCAPTURE	0x06

/*
 * Flow control register bit definitions.  A set bit indicates
 * that the register currently exhibits the corresponding mode.
 */

#define INTEL_PRGM	0x0001	/* Intelligent programming is in effect. */
#define CASCADE		0x0002	/* Currently splitting large SDR. */
#define REPEATLOOP	0x0008	/* Currently executing a repeat loop. */
#define SHIFTRIGHT	0x0080	/* The next data stream needs a right shift. */
#define SHIFTLEFT	0x0100	/* The next data stream needs a left shift. */
#define VERIFYUES	0x0200	/* Continue if fail is in effect. */

/*
 * DataType register bit definitions.  A set bit indicates
 * that the register currently holds the corresponding type of data.
 */

#define EXPRESS		0x0001    /* Simultaneous program and verify. */
#define SIR_DATA	0x0002    /* SIR is the active SVF command. */
#define SDR_DATA	0x0004    /* SDR is the active SVF command. */
#define COMPRESS	0x0008    /* Data is compressed. */
#define TDI_DATA	0x0010    /* TDI data is present. */
#define TDO_DATA	0x0020    /* TDO data is present. */
#define MASK_DATA	0x0040    /* MASK data is present. */
#define HEAP_IN		0x0080    /* Data is from the heap. */
#define LHEAP_IN	0x0200    /* Data is from intel data buffer. */
#define VARIABLE	0x0400    /* Data is from a declared variable. */
#define CRC_DATA	0x0800	 /* CRC data is pressent. */
#define CMASK_DATA	0x1000    /* CMASK data is pressent. */
#define RMASK_DATA	0x2000	 /* RMASK data is pressent. */
#define READ_DATA	0x4000    /* READ data is pressent. */
#define DMASK_DATA	0x8000	 /* DMASK data is pressent. */

/*
 *
 * Pin opcodes.
 *
 */

#define signalENABLE	0x1C    /* ispENABLE pin. */
#define signalTMS	0x1D    /* TMS pin. */
#define signalTCK	0x1E    /* TCK pin. */
#define signalTDI	0x1F    /* TDI pin. */
#define signalTRST	0x20    /* TRST pin. */

/*
 *
 * Supported vendors.
 *
 */

#define VENDOR		0x56
#define LATTICE		0x01
#define ALTERA		0x02
#define XILINX		0x03

/*
 * Opcode definitions.
 *
 * Note: opcodes must be unique.
 */

#define ENDDATA		0x00	/* The end of the current SDR data stream. */
#define RUNTEST		0x01	/* The duration to stay at the stable state. */
#define ENDDR		0x02	/* The stable state after SDR. */
#define ENDIR		0x03	/* The stable state after SIR. */
#define ENDSTATE	0x04	/* The stable state after RUNTEST. */
#define TRST		0x05	/* Assert the TRST pin. */
#define HIR		0x06	/*
				 * The sum of the IR bits of the
				 * leading devices.
				 */
#define TIR		0x07	/*
				 * The sum of the IR bits of the trailing
				 * devices.
				 */
#define HDR		0x08	/* The number of leading devices. */
#define TDR		0x09	/* The number of trailing devices. */
#define ispEN		0x0A	/* Assert the ispEN pin. */
#define FREQUENCY	0x0B	/*
				 * The maximum clock rate to run the JTAG state
				 * machine.
				 */
#define STATE		0x10	/* Move to the next stable state. */
#define SIR		0x11	/* The instruction stream follows. */
#define SDR		0x12	/* The data stream follows. */
#define TDI		0x13	/* The following data stream feeds into
					the device. */
#define TDO		0x14	/*
				 * The following data stream is compared against
				 * the device.
				 */
#define MASK		0x15	/* The following data stream is used as mask. */
#define XSDR		0x16	/*
				 * The following data stream is for simultaneous
				 * program and verify.
				 */
#define XTDI		0x17	/* The following data stream is for shift in
				 * only. It must be stored for the next
				 * XSDR.
				 */
#define XTDO		0x18	/*
				 * There is not data stream.  The data stream
				 * was stored from the previous XTDI.
				 */
#define MEM		0x19	/*
				 * The maximum memory needed to allocate in
				 * order hold one row of data.
				 */
#define WAIT		0x1A	/* The duration of delay to observe. */
#define TCK		0x1B	/* The number of TCK pulses. */
#define SHR		0x23	/*
				 * Set the flow control register for
				 * right shift
				 */
#define SHL		0x24	/*
				 * Set the flow control register for left shift.
				 */
#define HEAP		0x32	/* The memory size needed to hold one loop. */
#define REPEAT		0x33	/* The beginning of the loop. */
#define LEFTPAREN	0x35	/* The beginning of data following the loop. */
#define VAR		0x55	/* Plac holder for loop data. */
#define SEC		0x1C	/*
				 * The delay time in seconds that must be
				 * observed.
				 */
#define SMASK		0x1D	/* The mask for TDI data. */
#define MAX_WAIT	0x1E	/* The absolute maximum wait time. */
#define ON		0x1F	/* Assert the targeted pin. */
#define OFF		0x20	/* Dis-assert the targeted pin. */
#define SETFLOW		0x30	/* Change the flow control register. */
#define RESETFLOW	0x31	/* Clear the flow control register. */

#define CRC		0x47	/*
				 * The following data stream is used for CRC
				 * calculation.
				 */
#define CMASK		0x48	/*
				 * The following data stream is used as mask
				 * for CRC calculation.
				 */
#define RMASK		0x49	/*
				 * The following data stream is used as mask
				 * for read and save.
				 */
#define READ		0x50	/*
				 * The following data stream is used for read
				 * and save.
				 */
#define ENDLOOP		0x59	/* The end of the repeat loop. */
#define SECUREHEAP	0x60	/* Used to secure the HEAP opcode. */
#define VUES		0x61	/* Support continue if fail. */
#define DMASK		0x62	/*
				 * The following data stream is used for dynamic
				 * I/O.
				 */
#define COMMENT		0x63	/* Support SVF comments in the VME file. */
#define HEADER		0x64	/* Support header in VME file. */
#define FILE_CRC	0x65	/* Support crc-protected VME file. */
#define LCOUNT		0x66	/* Support intelligent programming. */
#define LDELAY		0x67	/* Support intelligent programming. */
#define LSDR		0x68	/* Support intelligent programming. */
#define LHEAP		0x69	/*
				 * Memory needed to hold intelligent data
				 * buffer
				 */
#define CONTINUE	0x70	/* Allow continuation. */
#define LVDS		0x71	/* Support LVDS. */
#define ENDVME		0x7F	/* End of the VME file. */
#define ENDFILE		0xFF	/* End of file. */

/*
 *
 * ispVM Embedded Return Codes.
 *
 */

#define VME_VERIFICATION_FAILURE	-1
#define VME_FILE_READ_FAILURE		-2
#define VME_VERSION_FAILURE		-3
#define VME_INVALID_FILE		-4
#define VME_ARGUMENT_FAILURE		-5
#define VME_CRC_FAILURE			-6

#define g_ucPinTDI	0x01
#define g_ucPinTCK	0x02
#define g_ucPinTMS	0x04
#define g_ucPinENABLE	0x08
#define g_ucPinTRST	0x10

/*
 *
 * Type definitions.
 *
 */

/* Support LVDS */
typedef struct {
	unsigned short usPositiveIndex;
	unsigned short usNegativeIndex;
	unsigned char  ucUpdate;
} LVDSPair;

typedef enum {
	min_lattice_iface_type,		/* insert all new types after this */
	lattice_jtag_mode,		/* jtag/tap  */
	max_lattice_iface_type		/* insert all new types before this */
} Lattice_iface;

typedef enum {
	min_lattice_type,
	Lattice_XP2,			/* Lattice XP2 Family */
	max_lattice_type		/* insert all new types before this */
} Lattice_Family;

typedef struct {
	Lattice_Family	family;	/* part type */
	Lattice_iface	iface;	/* interface type */
	size_t		size;	/* bytes of data part can accept */
	void		*iface_fns; /* interface function table */
	void		*base;	/* base interface address */
	int		cookie;	/* implementation specific cookie */
	char		*desc;	/* description string */
} Lattice_desc;			/* end, typedef Altera_desc */

/* Lattice Model Type */
#define CONFIG_SYS_XP2		CONFIG_SYS_FPGA_DEV(0x1)

/* Board specific implementation specific function types */
typedef void (*Lattice_jtag_init)(void);
typedef void (*Lattice_jtag_set_tdi)(int v);
typedef void (*Lattice_jtag_set_tms)(int v);
typedef void (*Lattice_jtag_set_tck)(int v);
typedef int (*Lattice_jtag_get_tdo)(void);

typedef struct {
	Lattice_jtag_init	jtag_init;
	Lattice_jtag_set_tdi	jtag_set_tdi;
	Lattice_jtag_set_tms	jtag_set_tms;
	Lattice_jtag_set_tck	jtag_set_tck;
	Lattice_jtag_get_tdo	jtag_get_tdo;
} lattice_board_specific_func;

void writePort(unsigned char pins, unsigned char value);
unsigned char readPort(void);
void sclock(void);
void ispVMDelay(unsigned short int a_usMicroSecondDelay);
void calibration(void);

int lattice_load(Lattice_desc *desc, void *buf, size_t bsize);
int lattice_dump(Lattice_desc *desc, void *buf, size_t bsize);
int lattice_info(Lattice_desc *desc);

void ispVMStart(void);
void ispVMEnd(void);
signed char ispVMCode(void);
void ispVMDelay(unsigned short int a_usMicroSecondDelay);
void ispVMCalculateCRC32(unsigned char a_ucData);
unsigned char GetByte(void);
void writePort(unsigned char pins, unsigned char value);
unsigned char readPort(void);
void sclock(void);
#endif