xref: /rk3399_rockchip-uboot/include/configs/zynq-common.h (revision caacb33fd1f9c270b0f0c878cfca08b56c0b257c)

/*
 * (C) Copyright 2012 Michal Simek <monstr@monstr.eu>
 * (C) Copyright 2013 Xilinx, Inc.
 *
 * Common configuration options for all Zynq boards.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_ZYNQ_COMMON_H
#define __CONFIG_ZYNQ_COMMON_H

/* CPU clock */
#ifndef CONFIG_CPU_FREQ_HZ
# define CONFIG_CPU_FREQ_HZ	800000000
#endif

/* Cache options */
#define CONFIG_CMD_CACHE
#define CONFIG_SYS_CACHELINE_SIZE	32

#define CONFIG_SYS_L2CACHE_OFF
#ifndef CONFIG_SYS_L2CACHE_OFF
# define CONFIG_SYS_L2_PL310
# define CONFIG_SYS_PL310_BASE		0xf8f02000
#endif

/* Serial drivers */
#define CONFIG_BAUDRATE		115200
/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE  \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}

/* DCC driver */
#if defined(CONFIG_ZYNQ_DCC)
# define CONFIG_ARM_DCC
# define CONFIG_CPU_V6 /* Required by CONFIG_ARM_DCC */
#else
# define CONFIG_ZYNQ_SERIAL
#endif

#define CONFIG_ZYNQ_GPIO
#define CONFIG_CMD_GPIO

/* Ethernet driver */
#if defined(CONFIG_ZYNQ_GEM0) || defined(CONFIG_ZYNQ_GEM1)
# define CONFIG_NET_MULTI
# define CONFIG_ZYNQ_GEM
# define CONFIG_MII
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
# define CONFIG_PHYLIB
# define CONFIG_PHY_MARVELL
# define CONFIG_BOOTP_SERVERIP
# define CONFIG_BOOTP_BOOTPATH
# define CONFIG_BOOTP_GATEWAY
# define CONFIG_BOOTP_HOSTNAME
# define CONFIG_BOOTP_MAY_FAIL
# if !defined(CONFIG_ZYNQ_GEM_EMIO0)
#  define CONFIG_ZYNQ_GEM_EMIO0	0
# endif
# if !defined(CONFIG_ZYNQ_GEM_EMIO1)
#  define CONFIG_ZYNQ_GEM_EMIO1	0
# endif
#endif

/* SPI */
#ifdef CONFIG_ZYNQ_SPI
# define CONFIG_SPI_FLASH
# define CONFIG_SPI_FLASH_SST
# define CONFIG_CMD_SF
#endif

/* NOR */
#ifndef CONFIG_SYS_NO_FLASH
# define CONFIG_SYS_FLASH_BASE		0xE2000000
# define CONFIG_SYS_FLASH_SIZE		(16 * 1024 * 1024)
# define CONFIG_SYS_MAX_FLASH_BANKS	1
# define CONFIG_SYS_MAX_FLASH_SECT	512
# define CONFIG_SYS_FLASH_ERASE_TOUT	1000
# define CONFIG_SYS_FLASH_WRITE_TOUT	5000
# define CONFIG_FLASH_SHOW_PROGRESS	10
# define CONFIG_SYS_FLASH_CFI
# undef CONFIG_SYS_FLASH_EMPTY_INFO
# define CONFIG_FLASH_CFI_DRIVER
# undef CONFIG_SYS_FLASH_PROTECTION
# define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#endif

/* MMC */
#if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1)
# define CONFIG_MMC
# define CONFIG_GENERIC_MMC
# define CONFIG_SDHCI
# define CONFIG_ZYNQ_SDHCI
# define CONFIG_CMD_MMC
#endif

#ifdef CONFIG_ZYNQ_USB
# define CONFIG_USB_EHCI
# define CONFIG_CMD_USB
# define CONFIG_USB_STORAGE
# define CONFIG_USB_EHCI_ZYNQ
# define CONFIG_USB_ULPI_VIEWPORT
# define CONFIG_USB_ULPI
# define CONFIG_EHCI_IS_TDI
# define CONFIG_USB_MAX_CONTROLLER_COUNT	2

# define CONFIG_CI_UDC           /* ChipIdea CI13xxx UDC */
# define CONFIG_USB_GADGET
# define CONFIG_USB_GADGET_DUALSPEED
# define CONFIG_USBDOWNLOAD_GADGET
# define CONFIG_SYS_DFU_DATA_BUF_SIZE	0x600000
# define DFU_DEFAULT_POLL_TIMEOUT	300
# define CONFIG_DFU_FUNCTION
# define CONFIG_DFU_RAM
# define CONFIG_USB_GADGET_VBUS_DRAW	2
# define CONFIG_G_DNL_VENDOR_NUM	0x03FD
# define CONFIG_G_DNL_PRODUCT_NUM	0x0300
# define CONFIG_G_DNL_MANUFACTURER	"Xilinx"
# define CONFIG_USB_GADGET
# define CONFIG_USB_CABLE_CHECK
# define CONFIG_CMD_DFU
# define CONFIG_CMD_THOR_DOWNLOAD
# define CONFIG_THOR_FUNCTION
# define DFU_ALT_INFO_RAM \
	"dfu_ram_info=" \
	"set dfu_alt_info " \
	"${kernel_image} ram 0x3000000 0x500000\\\\;" \
	"${devicetree_image} ram 0x2A00000 0x20000\\\\;" \
	"${ramdisk_image} ram 0x2000000 0x600000\0" \
	"dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
	"thor_ram=run dfu_ram_info && thordown 0 ram 0\0"

# if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1)
#  define CONFIG_DFU_MMC
#  define DFU_ALT_INFO_MMC \
	"dfu_mmc_info=" \
	"set dfu_alt_info " \
	"${kernel_image} fat 0 1\\\\;" \
	"${devicetree_image} fat 0 1\\\\;" \
	"${ramdisk_image} fat 0 1\0" \
	"dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \
	"thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0"

#  define DFU_ALT_INFO	\
	DFU_ALT_INFO_RAM \
	DFU_ALT_INFO_MMC
# else
#  define DFU_ALT_INFO	\
	DFU_ALT_INFO_RAM
# endif
#endif

#if !defined(DFU_ALT_INFO)
# define DFU_ALT_INFO
#endif

#if defined(CONFIG_ZYNQ_SDHCI) || defined(CONFIG_ZYNQ_USB)
# define CONFIG_SUPPORT_VFAT
# define CONFIG_CMD_FAT
# define CONFIG_CMD_EXT2
# define CONFIG_FAT_WRITE
# define CONFIG_DOS_PARTITION
# define CONFIG_CMD_EXT4
# define CONFIG_CMD_EXT4_WRITE
# define CONFIG_CMD_FS_GENERIC
#endif

#define CONFIG_SYS_I2C_ZYNQ
/* I2C */
#if defined(CONFIG_SYS_I2C_ZYNQ)
# define CONFIG_CMD_I2C
# define CONFIG_SYS_I2C
# define CONFIG_SYS_I2C_ZYNQ_SPEED		100000
# define CONFIG_SYS_I2C_ZYNQ_SLAVE		0
#endif

/* EEPROM */
#ifdef CONFIG_ZYNQ_EEPROM
# define CONFIG_CMD_EEPROM
# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
# define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
# define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
# define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
# define CONFIG_SYS_EEPROM_SIZE			1024 /* Bytes */
#endif

/* Total Size of Environment Sector */
#define CONFIG_ENV_SIZE			(128 << 10)

/* Allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE

/* Environment */
#ifndef CONFIG_ENV_IS_NOWHERE
# ifndef CONFIG_SYS_NO_FLASH
#  define CONFIG_ENV_IS_IN_FLASH
# elif defined(CONFIG_SYS_NO_FLASH)
#  define CONFIG_ENV_IS_NOWHERE
# endif

# define CONFIG_ENV_SECT_SIZE		CONFIG_ENV_SIZE
# define CONFIG_ENV_OFFSET		0xE0000
# define CONFIG_CMD_SAVEENV
#endif

/* Default environment */
#define CONFIG_EXTRA_ENV_SETTINGS	\
	"fit_image=fit.itb\0"		\
	"load_addr=0x2000000\0"		\
	"fit_size=0x800000\0"		\
	"flash_off=0x100000\0"		\
	"nor_flash_off=0xE2100000\0"	\
	"fdt_high=0x20000000\0"		\
	"initrd_high=0x20000000\0"	\
	"norboot=echo Copying FIT from NOR flash to RAM... && " \
		"cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \
		"bootm ${load_addr}\0" \
	"sdboot=echo Copying FIT from SD to RAM... && " \
		"load mmc 0 ${load_addr} ${fit_image} && " \
		"bootm ${load_addr}\0" \
	"jtagboot=echo TFTPing FIT to RAM... && " \
		"tftpboot ${load_addr} ${fit_image} && " \
		"bootm ${load_addr}\0" \
	"usbboot=if usb start; then " \
			"echo Copying FIT from USB to RAM... && " \
			"load usb 0 ${load_addr} ${fit_image} && " \
			"bootm ${load_addr}\0" \
		"fi\0" \
		DFU_ALT_INFO

#define CONFIG_BOOTCOMMAND		"run $modeboot"
#define CONFIG_BOOTDELAY		3 /* -1 to Disable autoboot */
#define CONFIG_SYS_LOAD_ADDR		0 /* default? */

/* Miscellaneous configurable options */
#define CONFIG_SYS_PROMPT		"zynq-uboot> "
#define CONFIG_SYS_HUSH_PARSER

#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_SYS_LONGHELP
#define CONFIG_CLOCKS
#define CONFIG_CMD_CLK
#define CONFIG_SYS_MAXARGS		32 /* max number of command args */
#define CONFIG_SYS_CBSIZE		256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
					sizeof(CONFIG_SYS_PROMPT) + 16)

/* Physical Memory map */
#define CONFIG_SYS_TEXT_BASE		0x4000000

#define CONFIG_NR_DRAM_BANKS		1
#define CONFIG_SYS_SDRAM_BASE		0

#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x1000)

#define CONFIG_SYS_MALLOC_LEN		0x1400000
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_MALLOC_LEN
#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
					CONFIG_SYS_INIT_RAM_SIZE - \
					GENERATED_GBL_DATA_SIZE)

/* Enable the PL to be downloaded */
#define CONFIG_FPGA
#define CONFIG_FPGA_XILINX
#define CONFIG_FPGA_ZYNQPL
#define CONFIG_CMD_FPGA
#define CONFIG_CMD_FPGA_LOADMK
#define CONFIG_CMD_FPGA_LOADP
#define CONFIG_CMD_FPGA_LOADBP
#define CONFIG_CMD_FPGA_LOADFS

/* Open Firmware flat tree */
#define CONFIG_OF_LIBFDT

/* FIT support */
#define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */

/* FDT support */
#define CONFIG_DISPLAY_BOARDINFO_LATE

/* Extend size of kernel image for uncompression */
#define CONFIG_SYS_BOOTM_LEN	(60 * 1024 * 1024)

/* Boot FreeBSD/vxWorks from an ELF image */
#if defined(CONFIG_ZYNQ_BOOT_FREEBSD)
# define CONFIG_API
# define CONFIG_CMD_ELF
# define CONFIG_SYS_MMC_MAX_DEVICE	1
#endif

#define CONFIG_SYS_LDSCRIPT  "arch/arm/cpu/armv7/zynq/u-boot.lds"

/* Commands */
#include <config_cmd_default.h>

#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
#define CONFIG_CMD_TFTPPUT

/* SPL part */
#define CONFIG_CMD_SPL
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_BOARD_INIT

#define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/armv7/zynq/u-boot-spl.lds"

/* MMC support */
#ifdef CONFIG_ZYNQ_SDHCI0
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS      0x200 /* 256 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot-dtb.img"
#endif

/* Disable dcache for SPL just for sure */
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_DCACHE_OFF
#undef CONFIG_FPGA
#endif

/* Address in RAM where the parameters must be copied by SPL. */
#define CONFIG_SYS_SPL_ARGS_ADDR	0x10000000

#define CONFIG_SPL_FS_LOAD_ARGS_NAME		"system.dtb"
#define CONFIG_SPL_FS_LOAD_KERNEL_NAME		"uImage"

/* Not using MMC raw mode - just for compilation purpose */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR	0
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS	0
#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR	0

/* qspi mode is working fine */
#ifdef CONFIG_ZYNQ_QSPI
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x100000
#endif

/* for booting directly linux */
#define CONFIG_SPL_OS_BOOT

/* SP location before relocation, must use scratch RAM */
#define CONFIG_SPL_TEXT_BASE	0x0

/* 3 * 64kB blocks of OCM - one is on the top because of bootrom */
#define CONFIG_SPL_MAX_SIZE	0x30000

/* The highest 64k OCM address */
#define OCM_HIGH_ADDR	0xffff0000

/* Just define any reasonable size */
#define CONFIG_SPL_STACK_SIZE	0x1000

/* SPL stack position - and stack goes down */
#define CONFIG_SPL_STACK	(OCM_HIGH_ADDR + CONFIG_SPL_STACK_SIZE)

/* On the top of OCM space */
#define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_STACK + \
					 GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_SPL_MALLOC_SIZE	0x1000

/* BSS setup */
#define CONFIG_SPL_BSS_START_ADDR	0x100000
#define CONFIG_SPL_BSS_MAX_SIZE		0x100000

#define CONFIG_SYS_UBOOT_START	CONFIG_SYS_TEXT_BASE

#define CONFIG_SYS_GENERIC_BOARD

#endif /* __CONFIG_ZYNQ_COMMON_H */