1 /* 2 * Copyright (C) 2012-2015 Panasonic Corporation 3 * Author: Masahiro Yamada <yamada.m@jp.panasonic.com> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* U-boot - Common settings for UniPhier Family */ 9 10 #ifndef __CONFIG_UNIPHIER_COMMON_H__ 11 #define __CONFIG_UNIPHIER_COMMON_H__ 12 13 #if defined(CONFIG_MACH_PH1_PRO4) 14 #define CONFIG_DDR_NUM_CH0 2 15 #define CONFIG_DDR_NUM_CH1 2 16 17 /* Physical start address of SDRAM */ 18 #define CONFIG_SDRAM0_BASE 0x80000000 19 #define CONFIG_SDRAM0_SIZE 0x20000000 20 #define CONFIG_SDRAM1_BASE 0xa0000000 21 #define CONFIG_SDRAM1_SIZE 0x20000000 22 #endif 23 24 #if defined(CONFIG_MACH_PH1_LD4) 25 #define CONFIG_DDR_NUM_CH0 1 26 #define CONFIG_DDR_NUM_CH1 1 27 28 /* Physical start address of SDRAM */ 29 #define CONFIG_SDRAM0_BASE 0x80000000 30 #define CONFIG_SDRAM0_SIZE 0x10000000 31 #define CONFIG_SDRAM1_BASE 0x90000000 32 #define CONFIG_SDRAM1_SIZE 0x10000000 33 #endif 34 35 #if defined(CONFIG_MACH_PH1_SLD8) 36 #define CONFIG_DDR_NUM_CH0 1 37 #define CONFIG_DDR_NUM_CH1 1 38 39 /* Physical start address of SDRAM */ 40 #define CONFIG_SDRAM0_BASE 0x80000000 41 #define CONFIG_SDRAM0_SIZE 0x10000000 42 #define CONFIG_SDRAM1_BASE 0x90000000 43 #define CONFIG_SDRAM1_SIZE 0x10000000 44 #endif 45 46 #define CONFIG_I2C_EEPROM 47 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 48 49 /* 50 * Support card address map 51 */ 52 #if defined(CONFIG_PFC_MICRO_SUPPORT_CARD) 53 # define CONFIG_SUPPORT_CARD_BASE 0x03f00000 54 # define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000) 55 # define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00090000) 56 # define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x000b0000) 57 #endif 58 59 #if defined(CONFIG_DCC_MICRO_SUPPORT_CARD) 60 # define CONFIG_SUPPORT_CARD_BASE 0x08000000 61 # define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000) 62 # define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00401630) 63 # define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00200000) 64 #endif 65 66 #ifdef CONFIG_SYS_NS16550_SERIAL 67 #define CONFIG_SYS_NS16550 68 #define CONFIG_SYS_NS16550_COM1 CONFIG_SUPPORT_CARD_UART_BASE 69 #define CONFIG_SYS_NS16550_CLK 12288000 70 #define CONFIG_SYS_NS16550_REG_SIZE -2 71 #endif 72 73 /* TODO: move to Kconfig and device tree */ 74 #if 0 75 #define CONFIG_SYS_NS16550_SERIAL 76 #endif 77 78 #define CONFIG_SMC911X 79 80 #define CONFIG_SMC911X_BASE CONFIG_SUPPORT_CARD_ETHER_BASE 81 #define CONFIG_SMC911X_32_BIT 82 83 #define CONFIG_SYS_MALLOC_F_LEN 0x2000 84 85 /*----------------------------------------------------------------------- 86 * MMU and Cache Setting 87 *----------------------------------------------------------------------*/ 88 89 /* Comment out the following to enable L1 cache */ 90 /* #define CONFIG_SYS_ICACHE_OFF */ 91 /* #define CONFIG_SYS_DCACHE_OFF */ 92 93 /* Comment out the following to enable L2 cache */ 94 #define CONFIG_UNIPHIER_L2CACHE_ON 95 96 #define CONFIG_DISPLAY_CPUINFO 97 #define CONFIG_DISPLAY_BOARDINFO 98 #define CONFIG_BOARD_EARLY_INIT_F 99 #define CONFIG_BOARD_EARLY_INIT_R 100 #define CONFIG_BOARD_LATE_INIT 101 102 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 103 104 #define CONFIG_TIMESTAMP 105 106 /* FLASH related */ 107 #define CONFIG_MTD_DEVICE 108 109 /* 110 * uncomment the following to disable FLASH related code. 111 */ 112 /* #define CONFIG_SYS_NO_FLASH */ 113 114 #define CONFIG_FLASH_CFI_DRIVER 115 #define CONFIG_SYS_FLASH_CFI 116 117 #define CONFIG_SYS_MAX_FLASH_SECT 256 118 #define CONFIG_SYS_MONITOR_BASE 0 119 #define CONFIG_SYS_FLASH_BASE 0 120 121 /* 122 * flash_toggle does not work for out supoort card. 123 * We need to use flash_status_poll. 124 */ 125 #define CONFIG_SYS_CFI_FLASH_STATUS_POLL 126 127 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 128 129 #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 130 131 /* serial console configuration */ 132 #define CONFIG_BAUDRATE 115200 133 134 #define CONFIG_SYS_GENERIC_BOARD 135 136 #if !defined(CONFIG_SPL_BUILD) 137 #define CONFIG_USE_ARCH_MEMSET 138 #define CONFIG_USE_ARCH_MEMCPY 139 #endif 140 141 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 142 143 #define CONFIG_CMDLINE_EDITING /* add command line history */ 144 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 145 /* Print Buffer Size */ 146 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 147 #define CONFIG_SYS_MAXARGS 16 /* max number of command */ 148 /* Boot Argument Buffer Size */ 149 #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) 150 151 #define CONFIG_CONS_INDEX 1 152 153 /* 154 * For NAND booting the environment is embedded in the U-Boot image. Please take 155 * look at the file board/amcc/canyonlands/u-boot-nand.lds for details. 156 */ 157 /* #define CONFIG_ENV_IS_IN_NAND */ 158 #define CONFIG_ENV_IS_NOWHERE 159 #define CONFIG_ENV_SIZE 0x2000 160 #define CONFIG_ENV_OFFSET 0x0 161 /* #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */ 162 163 /* Time clock 1MHz */ 164 #define CONFIG_SYS_TIMER_RATE 1000000 165 166 /* 167 * By default, ARP timeout is 5 sec. 168 * The first ARP request does not seem to work. 169 * So we need to retry ARP request anyway. 170 * We want to shrink the interval until the second ARP request. 171 */ 172 #define CONFIG_ARP_TIMEOUT 500UL /* 0.5 msec */ 173 174 #define CONFIG_SYS_MAX_NAND_DEVICE 1 175 #define CONFIG_SYS_NAND_MAX_CHIPS 2 176 #define CONFIG_SYS_NAND_ONFI_DETECTION 177 178 #define CONFIG_NAND_DENALI_ECC_SIZE 1024 179 180 #define CONFIG_SYS_NAND_REGS_BASE 0x68100000 181 #define CONFIG_SYS_NAND_DATA_BASE 0x68000000 182 183 #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_DATA_BASE + 0x10) 184 185 #define CONFIG_SYS_NAND_USE_FLASH_BBT 186 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 187 188 /* USB */ 189 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 190 #define CONFIG_CMD_FAT 191 #define CONFIG_FAT_WRITE 192 #define CONFIG_DOS_PARTITION 193 194 #define CONFIG_CMD_DM 195 196 /* memtest works on */ 197 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 198 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01000000) 199 200 #define CONFIG_BOOTDELAY 3 201 #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ 202 #define CONFIG_AUTOBOOT_KEYED 1 203 #define CONFIG_AUTOBOOT_PROMPT \ 204 "Press SPACE to abort autoboot in %d seconds\n", bootdelay 205 #define CONFIG_AUTOBOOT_DELAY_STR "d" 206 #define CONFIG_AUTOBOOT_STOP_STR " " 207 208 /* 209 * Network Configuration 210 */ 211 #define CONFIG_ETHADDR 00:21:83:24:00:00 212 #define CONFIG_SERVERIP 192.168.11.1 213 #define CONFIG_IPADDR 192.168.11.10 214 #define CONFIG_GATEWAYIP 192.168.11.1 215 #define CONFIG_NETMASK 255.255.255.0 216 217 #define CONFIG_LOADADDR 0x84000000 218 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR 219 #define CONFIG_BOOTFILE "fit.itb" 220 221 #define CONFIG_CMDLINE_EDITING /* add command line history */ 222 223 #define CONFIG_BOOTCOMMAND "run $bootmode" 224 225 #define CONFIG_ROOTPATH "/nfs/root/path" 226 #define CONFIG_NFSBOOTCOMMAND \ 227 "setenv bootargs $bootargs root=/dev/nfs rw " \ 228 "nfsroot=$serverip:$rootpath " \ 229 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \ 230 "tftpboot; bootm;" 231 232 #define CONFIG_BOOTARGS " user_debug=0x1f init=/sbin/init" 233 234 #define CONFIG_EXTRA_ENV_SETTINGS \ 235 "netdev=eth0\0" \ 236 "image_offset=0x00080000\0" \ 237 "image_size=0x00f00000\0" \ 238 "verify=n\0" \ 239 "nandupdate=nand erase 0 0x100000 &&" \ 240 "tftpboot u-boot-spl.bin &&" \ 241 "nand write $loadaddr 0 0x10000 &&" \ 242 "tftpboot u-boot-dtb.img &&" \ 243 "nand write $loadaddr 0x10000 0xf0000\0" \ 244 "norboot=run add_default_bootargs &&" \ 245 "bootm $image_offset\0" \ 246 "nandboot=run add_default_bootargs &&" \ 247 "nand read $loadaddr $image_offset $image_size &&" \ 248 "bootm\0" \ 249 "add_default_bootargs=setenv bootargs $bootargs" \ 250 " console=ttyS0,$baudrate\0" \ 251 252 /* Open Firmware flat tree */ 253 #define CONFIG_OF_LIBFDT 254 255 #define CONFIG_HAVE_ARM_SECURE 256 257 /* Memory Size & Mapping */ 258 #define CONFIG_SYS_SDRAM_BASE CONFIG_SDRAM0_BASE 259 260 #if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE >= CONFIG_SDRAM1_BASE 261 /* Thre is no memory hole */ 262 #define CONFIG_NR_DRAM_BANKS 1 263 #define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE + CONFIG_SDRAM1_SIZE) 264 #else 265 #define CONFIG_NR_DRAM_BANKS 2 266 #define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE) 267 #endif 268 269 #define CONFIG_SYS_TEXT_BASE 0x84000000 270 271 #if defined(CONFIG_MACH_PH1_LD4) || defined(CONFIG_MACH_PH1_SLD8) 272 #define CONFIG_SPL_TEXT_BASE 0x00040000 273 #endif 274 #if defined(CONFIG_MACH_PH1_PRO4) 275 #define CONFIG_SPL_TEXT_BASE 0x00100000 276 #endif 277 278 #define CONFIG_BOARD_POSTCLK_INIT 279 280 #ifndef CONFIG_SPL_BUILD 281 #define CONFIG_SKIP_LOWLEVEL_INIT 282 #endif 283 284 #define CONFIG_SYS_SPL_MALLOC_START (0x0ff00000) 285 #define CONFIG_SYS_SPL_MALLOC_SIZE (0x00004000) 286 287 #ifdef CONFIG_SPL_BUILD 288 #define CONFIG_SYS_INIT_SP_ADDR (0x0ff08000) 289 #else 290 #define CONFIG_SYS_INIT_SP_ADDR ((CONFIG_SYS_TEXT_BASE) - 0x00001000) 291 #endif 292 293 #define CONFIG_SPL_FRAMEWORK 294 #define CONFIG_SPL_NAND_SUPPORT 295 296 #define CONFIG_SPL_LIBCOMMON_SUPPORT /* for mem_malloc_init */ 297 #define CONFIG_SPL_LIBGENERIC_SUPPORT 298 299 #define CONFIG_SPL_BOARD_INIT 300 301 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x10000 302 303 #endif /* __CONFIG_UNIPHIER_COMMON_H__ */ 304