xref: /rk3399_rockchip-uboot/include/configs/uniphier.h (revision 4aceb3f8d4bfcafa895ecbc3108e1f35f2b8c091)

/*
 * Copyright (C) 2012-2015 Masahiro Yamada <yamada.masahiro@socionext.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/* U-Boot - Common settings for UniPhier Family */

#ifndef __CONFIG_UNIPHIER_COMMON_H__
#define __CONFIG_UNIPHIER_COMMON_H__

#define CONFIG_I2C_EEPROM
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  10

#ifdef CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_COM1		CONFIG_SUPPORT_CARD_UART_BASE
#define CONFIG_SYS_NS16550_CLK		12288000
#define CONFIG_SYS_NS16550_REG_SIZE	-2
#endif

/* TODO: move to Kconfig and device tree */
#if 0
#define CONFIG_SYS_NS16550_SERIAL
#endif

#define CONFIG_SMC911X

/* dummy: referenced by examples/standalone/smc911x_eeprom.c */
#define CONFIG_SMC911X_BASE	0
#define CONFIG_SMC911X_32_BIT

/*-----------------------------------------------------------------------
 * MMU and Cache Setting
 *----------------------------------------------------------------------*/

/* Comment out the following to enable L1 cache */
/* #define CONFIG_SYS_ICACHE_OFF */
/* #define CONFIG_SYS_DCACHE_OFF */

#define CONFIG_SYS_CACHELINE_SIZE	32

/* Comment out the following to enable L2 cache */
#define CONFIG_UNIPHIER_L2CACHE_ON

#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_MISC_INIT_F
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_BOARD_LATE_INIT

#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)

#define CONFIG_TIMESTAMP

/* FLASH related */
#define CONFIG_MTD_DEVICE

/*
 * uncomment the following to disable FLASH related code.
 */
/* #define CONFIG_SYS_NO_FLASH */

#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI

#define CONFIG_SYS_MAX_FLASH_SECT	256
#define CONFIG_SYS_MONITOR_BASE		0
#define CONFIG_SYS_FLASH_BASE		0

/*
 * flash_toggle does not work for out supoort card.
 * We need to use flash_status_poll.
 */
#define CONFIG_SYS_CFI_FLASH_STATUS_POLL

#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */

#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1

/* serial console configuration */
#define CONFIG_BAUDRATE			115200


#if !defined(CONFIG_SPL_BUILD)
#define CONFIG_USE_ARCH_MEMSET
#define CONFIG_USE_ARCH_MEMCPY
#endif

#define CONFIG_SYS_LONGHELP		/* undef to save memory */

#define CONFIG_CMDLINE_EDITING		/* add command line history	*/
#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS		16	/* max number of command */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)

#define CONFIG_CONS_INDEX		1

/*
 * For NAND booting the environment is embedded in the U-Boot image. Please take
 * look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
 */
/* #define CONFIG_ENV_IS_IN_NAND */
#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_SIZE				0x2000
#define CONFIG_ENV_OFFSET			0x0
/* #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */

/* Time clock 1MHz */
#define CONFIG_SYS_TIMER_RATE			1000000

/*
 * By default, ARP timeout is 5 sec.
 * The first ARP request does not seem to work.
 * So we need to retry ARP request anyway.
 * We want to shrink the interval until the second ARP request.
 */
#define CONFIG_ARP_TIMEOUT	500UL  /* 0.5 msec */

#define CONFIG_SYS_MAX_NAND_DEVICE			1
#define CONFIG_SYS_NAND_MAX_CHIPS			2
#define CONFIG_SYS_NAND_ONFI_DETECTION

#define CONFIG_NAND_DENALI_ECC_SIZE			1024

#ifdef CONFIG_ARCH_UNIPHIER_PH1_SLD3
#define CONFIG_SYS_NAND_REGS_BASE			0xf8100000
#define CONFIG_SYS_NAND_DATA_BASE			0xf8000000
#else
#define CONFIG_SYS_NAND_REGS_BASE			0x68100000
#define CONFIG_SYS_NAND_DATA_BASE			0x68000000
#endif

#define CONFIG_SYS_NAND_BASE		(CONFIG_SYS_NAND_DATA_BASE + 0x10)

#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_BAD_BLOCK_POS			0

/* USB */
#define CONFIG_USB_MAX_CONTROLLER_COUNT		2
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS	4
#define CONFIG_CMD_FAT
#define CONFIG_FAT_WRITE
#define CONFIG_DOS_PARTITION

/* SD/MMC */
#define CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC

/* memtest works on */
#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x01000000)

#define CONFIG_BOOTDELAY			3
#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */

/*
 * Network Configuration
 */
#define CONFIG_SERVERIP			192.168.11.1
#define CONFIG_IPADDR			192.168.11.10
#define CONFIG_GATEWAYIP		192.168.11.1
#define CONFIG_NETMASK			255.255.255.0

#define CONFIG_LOADADDR			0x84000000
#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR

#define CONFIG_CMDLINE_EDITING		/* add command line history	*/

#define CONFIG_BOOTCOMMAND		"run $bootmode"

#define CONFIG_ROOTPATH			"/nfs/root/path"
#define CONFIG_NFSBOOTCOMMAND						\
	"setenv bootargs $bootargs root=/dev/nfs rw "			\
	"nfsroot=$serverip:$rootpath "					\
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
		"run __nfsboot"

#ifdef CONFIG_FIT
#define CONFIG_BOOTFILE			"fitImage"
#define LINUXBOOT_ENV_SETTINGS \
	"fit_addr=0x00100000\0" \
	"fit_addr_r=0x84100000\0" \
	"fit_size=0x00f00000\0" \
	"norboot=setexpr fit_addr $nor_base + $fit_addr &&" \
		"bootm $fit_addr\0" \
	"nandboot=nand read $fit_addr_r $fit_addr $fit_size &&" \
		"bootm $fit_addr_r\0" \
	"tftpboot=tftpboot $fit_addr_r $bootfile &&" \
		"bootm $fit_addr_r\0" \
	"__nfsboot=run tftpboot\0"
#else
#define CONFIG_CMD_BOOTZ
#define CONFIG_BOOTFILE			"zImage"
#define LINUXBOOT_ENV_SETTINGS \
	"fdt_addr=0x00100000\0" \
	"fdt_addr_r=0x84100000\0" \
	"fdt_size=0x00008000\0" \
	"kernel_addr=0x00200000\0" \
	"kernel_addr_r=0x80208000\0" \
	"kernel_size=0x00800000\0" \
	"ramdisk_addr=0x00a00000\0" \
	"ramdisk_addr_r=0x84a00000\0" \
	"ramdisk_size=0x00600000\0" \
	"ramdisk_file=rootfs.cpio.uboot\0" \
	"boot_common=setexpr bootm_low $kernel_addr_r '&' fe000000 &&" \
		"bootz $kernel_addr_r $ramdisk_addr_r $fdt_addr_r\0" \
	"norboot=setexpr kernel_addr $nor_base + $kernel_addr &&" \
		"cp.b $kernel_addr $kernel_addr_r $kernel_size &&" \
		"setexpr ramdisk_addr_r $nor_base + $ramdisk_addr &&" \
		"setexpr fdt_addr_r $nor_base + $fdt_addr &&" \
		"run boot_common\0" \
	"nandboot=nand read $kernel_addr_r $kernel_addr $kernel_size &&" \
		"nand read $ramdisk_addr_r $ramdisk_addr $ramdisk_size &&" \
		"nand read $fdt_addr_r $fdt_addr $fdt_size &&" \
		"run boot_common\0" \
	"tftpboot=tftpboot $kernel_addr_r $bootfile &&" \
		"tftpboot $ramdisk_addr_r $ramdisk_file &&" \
		"tftpboot $fdt_addr_r $fdt_file &&" \
		"run boot_common\0" \
	"__nfsboot=tftpboot $kernel_addr_r $bootfile &&" \
		"tftpboot $fdt_addr_r $fdt_file &&" \
		"tftpboot $fdt_addr_r $fdt_file &&" \
		"setenv ramdisk_addr_r - &&" \
		"run boot_common\0"
#endif

#define	CONFIG_EXTRA_ENV_SETTINGS				\
	"netdev=eth0\0"						\
	"verify=n\0"						\
	"nor_base=0x42000000\0"					\
	"nandupdate=nand erase 0 0x00100000 &&"			\
		"tftpboot u-boot-spl.bin &&"			\
		"nand write $loadaddr 0 0x00010000 &&"		\
		"tftpboot u-boot.img &&"			\
		"nand write $loadaddr 0x00010000 0x000f0000\0"	\
	LINUXBOOT_ENV_SETTINGS

#define CONFIG_SYS_BOOTMAPSZ			0x20000000

/* Open Firmware flat tree */
#define CONFIG_OF_LIBFDT

#define CONFIG_SYS_SDRAM_BASE		0x80000000
#define CONFIG_NR_DRAM_BANKS		2

#if defined(CONFIG_ARCH_UNIPHIER_PH1_SLD3) || \
	defined(CONFIG_ARCH_UNIPHIER_PH1_LD4) || \
	defined(CONFIG_ARCH_UNIPHIER_PH1_SLD8)
#define CONFIG_SPL_TEXT_BASE		0x00040000
#else
#define CONFIG_SPL_TEXT_BASE		0x00100000
#endif

#define CONFIG_SPL_STACK		(0x00100000)
#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE)

#define CONFIG_PANIC_HANG

#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT

#define CONFIG_SPL_LIBCOMMON_SUPPORT	/* for mem_malloc_init */
#define CONFIG_SPL_LIBGENERIC_SUPPORT

#define CONFIG_SPL_BOARD_INIT

#define CONFIG_SYS_NAND_U_BOOT_OFFS		0x10000

#define CONFIG_SPL_MAX_FOOTPRINT		0x10000

#endif /* __CONFIG_UNIPHIER_COMMON_H__ */