1 /* 2 * (C) Copyright 2012-2016 Stephen Warren 3 * 4 * SPDX-License-Identifier: GPL-2.0 5 */ 6 7 #ifndef __CONFIG_H 8 #define __CONFIG_H 9 10 #include <linux/sizes.h> 11 #include <asm/arch/timer.h> 12 13 #if defined(CONFIG_TARGET_RPI_2) || defined(CONFIG_TARGET_RPI_3_32B) 14 #define CONFIG_SKIP_LOWLEVEL_INIT 15 #endif 16 17 /* Architecture, CPU, etc.*/ 18 #define CONFIG_ARCH_CPU_INIT 19 20 /* Use SoC timer for AArch32, but architected timer for AArch64 */ 21 #ifndef CONFIG_ARM64 22 #define CONFIG_SYS_TIMER_RATE 1000000 23 #define CONFIG_SYS_TIMER_COUNTER \ 24 (&((struct bcm2835_timer_regs *)BCM2835_TIMER_PHYSADDR)->clo) 25 #endif 26 27 /* 28 * 2835 is a SKU in a series for which the 2708 is the first or primary SoC, 29 * so 2708 has historically been used rather than a dedicated 2835 ID. 30 * 31 * We don't define a machine type for bcm2709/bcm2836 since the RPi Foundation 32 * chose to use someone else's previously registered machine ID (3139, MX51_GGC) 33 * rather than obtaining a valid ID:-/ 34 * 35 * For the bcm2837, hopefully a machine type is not needed, since everything 36 * is DT. 37 */ 38 #ifdef CONFIG_BCM2835 39 #define CONFIG_MACH_TYPE MACH_TYPE_BCM2708 40 #endif 41 42 /* Memory layout */ 43 #define CONFIG_NR_DRAM_BANKS 1 44 #define CONFIG_SYS_SDRAM_BASE 0x00000000 45 #ifdef CONFIG_ARM64 46 #define CONFIG_SYS_TEXT_BASE 0x00080000 47 #else 48 #define CONFIG_SYS_TEXT_BASE 0x00008000 49 #endif 50 #define CONFIG_SYS_UBOOT_BASE CONFIG_SYS_TEXT_BASE 51 /* 52 * The board really has 256M. However, the VC (VideoCore co-processor) shares 53 * the RAM, and uses a configurable portion at the top. We tell U-Boot that a 54 * smaller amount of RAM is present in order to avoid stomping on the area 55 * the VC uses. 56 */ 57 #define CONFIG_SYS_SDRAM_SIZE SZ_128M 58 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \ 59 CONFIG_SYS_SDRAM_SIZE - \ 60 GENERATED_GBL_DATA_SIZE) 61 #define CONFIG_SYS_MALLOC_LEN SZ_4M 62 #define CONFIG_SYS_MEMTEST_START 0x00100000 63 #define CONFIG_SYS_MEMTEST_END 0x00200000 64 #define CONFIG_LOADADDR 0x00200000 65 66 /* Flash */ 67 #define CONFIG_SYS_NO_FLASH 68 69 /* Devices */ 70 /* GPIO */ 71 #define CONFIG_BCM2835_GPIO 72 /* LCD */ 73 #define CONFIG_LCD_DT_SIMPLEFB 74 #define LCD_BPP LCD_COLOR32 75 /* 76 * Prevent allocation of RAM for FB; the real FB address is queried 77 * dynamically from the VideoCore co-processor, and comes from RAM 78 * not owned by the ARM CPU. 79 */ 80 #define CONFIG_FB_ADDR 0 81 #define CONFIG_VIDEO_BCM2835 82 #define CONFIG_SYS_WHITE_ON_BLACK 83 84 /* SD/MMC configuration */ 85 #define CONFIG_GENERIC_MMC 86 #define CONFIG_MMC_SDHCI_IO_ACCESSORS 87 88 #ifdef CONFIG_CMD_USB 89 #define CONFIG_USB_DWC2 90 #ifndef CONFIG_BCM2835 91 #define CONFIG_USB_DWC2_REG_ADDR 0x3f980000 92 #else 93 #define CONFIG_USB_DWC2_REG_ADDR 0x20980000 94 #endif 95 #define CONFIG_USB_HOST_ETHER 96 #define CONFIG_USB_ETHER_SMSC95XX 97 #define CONFIG_TFTP_TSIZE 98 #define CONFIG_MISC_INIT_R 99 #define CONFIG_SYS_USB_EVENT_POLL 100 #endif 101 102 /* Console UART */ 103 #ifdef CONFIG_BCM2837 104 #define CONFIG_BCM283X_MU_SERIAL 105 #else 106 #define CONFIG_PL01X_SERIAL 107 #endif 108 #define CONFIG_CONS_INDEX 0 109 #define CONFIG_BAUDRATE 115200 110 111 /* Console configuration */ 112 #define CONFIG_SYS_CBSIZE 1024 113 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 114 sizeof(CONFIG_SYS_PROMPT) + 16) 115 116 /* Environment */ 117 #define CONFIG_ENV_SIZE SZ_16K 118 #define CONFIG_ENV_IS_IN_FAT 119 #define FAT_ENV_INTERFACE "mmc" 120 #define FAT_ENV_DEVICE_AND_PART "0:1" 121 #define FAT_ENV_FILE "uboot.env" 122 #define CONFIG_FAT_WRITE 123 #define CONFIG_ENV_VARS_UBOOT_CONFIG 124 #define CONFIG_SYS_LOAD_ADDR 0x1000000 125 #define CONFIG_PREBOOT "usb start" 126 127 /* Shell */ 128 #define CONFIG_SYS_MAXARGS 16 129 #define CONFIG_COMMAND_HISTORY 130 131 /* Commands */ 132 #define CONFIG_PARTITION_UUIDS 133 #define CONFIG_CMD_PART 134 135 /* ATAGs support for bootm/bootz */ 136 #define CONFIG_SETUP_MEMORY_TAGS 137 #define CONFIG_CMDLINE_TAG 138 #define CONFIG_INITRD_TAG 139 140 #include <config_distro_defaults.h> 141 142 /* Environment */ 143 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG 144 #define ENV_DEVICE_SETTINGS \ 145 "stdin=serial,usbkbd\0" \ 146 "stdout=serial,lcd\0" \ 147 "stderr=serial,lcd\0" 148 149 /* 150 * Memory layout for where various images get loaded by boot scripts: 151 * 152 * I suspect address 0 is used as the SMP pen on the RPi2, so avoid this. 153 * 154 * fdt_addr_r simply shouldn't overlap anything else. However, the RPi's 155 * binary firmware loads a DT to address 0x100, so we choose this address to 156 * match it. This allows custom boot scripts to pass this DT on to Linux 157 * simply by not over-writing the data at this address. When using U-Boot, 158 * U-Boot (and scripts it executes) typicaly ignore the DT loaded by the FW 159 * and loads its own DT from disk (triggered by boot.scr or extlinux.conf). 160 * 161 * pxefile_addr_r can be pretty much anywhere that doesn't conflict with 162 * something else. Put it low in memory to avoid conflicts. 163 * 164 * kernel_addr_r must be within the first 128M of RAM in order for the 165 * kernel's CONFIG_AUTO_ZRELADDR option to work. Since the kernel will 166 * decompress itself to 0x8000 after the start of RAM, kernel_addr_r 167 * should not overlap that area, or the kernel will have to copy itself 168 * somewhere else before decompression. Similarly, the address of any other 169 * data passed to the kernel shouldn't overlap the start of RAM. Pushing 170 * this up to 16M allows for a sizable kernel to be decompressed below the 171 * compressed load address. 172 * 173 * scriptaddr can be pretty much anywhere that doesn't conflict with something 174 * else. Choosing 32M allows for the compressed kernel to be up to 16M. 175 * 176 * ramdisk_addr_r simply shouldn't overlap anything else. Choosing 33M allows 177 * for any boot script to be up to 1M, which is hopefully plenty. 178 */ 179 #define ENV_MEM_LAYOUT_SETTINGS \ 180 "fdt_high=ffffffff\0" \ 181 "initrd_high=ffffffff\0" \ 182 "fdt_addr_r=0x00000100\0" \ 183 "pxefile_addr_r=0x00100000\0" \ 184 "kernel_addr_r=0x01000000\0" \ 185 "scriptaddr=0x02000000\0" \ 186 "ramdisk_addr_r=0x02100000\0" \ 187 188 #define BOOT_TARGET_DEVICES(func) \ 189 func(MMC, mmc, 0) \ 190 func(USB, usb, 0) \ 191 func(PXE, pxe, na) \ 192 func(DHCP, dhcp, na) 193 #include <config_distro_bootcmd.h> 194 195 #define CONFIG_EXTRA_ENV_SETTINGS \ 196 "dhcpuboot=usb start; dhcp u-boot.uimg; bootm\0" \ 197 ENV_DEVICE_SETTINGS \ 198 ENV_MEM_LAYOUT_SETTINGS \ 199 BOOTENV 200 201 202 #endif 203