1 /* 2 * Copyright 2013 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * QorIQ P1 Tower boards configuration file 9 */ 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 #if defined(CONFIG_TWR_P1025) 14 #define CONFIG_BOARDNAME "TWR-P1025" 15 #define CONFIG_PHY_ATHEROS 16 #define CONFIG_QE 17 #define CONFIG_SYS_LBC_LBCR 0x00080000 /* Conversion of LBC addr */ 18 #define CONFIG_SYS_LBC_LCRR 0x80000002 /* LB clock ratio reg */ 19 #endif 20 21 #ifdef CONFIG_SDCARD 22 #define CONFIG_RAMBOOT_SDCARD 23 #define CONFIG_SYS_RAMBOOT 24 #define CONFIG_SYS_EXTRA_ENV_RELOC 25 #define CONFIG_SYS_TEXT_BASE 0x11000000 26 #define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc 27 #endif 28 29 #ifndef CONFIG_SYS_TEXT_BASE 30 #define CONFIG_SYS_TEXT_BASE 0xeff40000 31 #endif 32 33 #ifndef CONFIG_RESET_VECTOR_ADDRESS 34 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 35 #endif 36 37 #ifndef CONFIG_SYS_MONITOR_BASE 38 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 39 #endif 40 41 #define CONFIG_MP 42 43 #define CONFIG_FSL_ELBC 44 #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */ 45 #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */ 46 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 47 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ 48 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 49 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 50 51 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 52 #define CONFIG_ENV_OVERWRITE 53 54 #define CONFIG_CMD_SATA 55 #define CONFIG_SATA_SIL3114 56 #define CONFIG_SYS_SATA_MAX_DEVICE 2 57 #define CONFIG_LIBATA 58 #define CONFIG_LBA48 59 60 #ifndef __ASSEMBLY__ 61 extern unsigned long get_board_sys_clk(unsigned long dummy); 62 #endif 63 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /*sysclk for TWR-P1025 */ 64 65 #define CONFIG_DDR_CLK_FREQ 66666666 66 67 #define CONFIG_HWCONFIG 68 /* 69 * These can be toggled for performance analysis, otherwise use default. 70 */ 71 #define CONFIG_L2_CACHE 72 #define CONFIG_BTB 73 74 #define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ 75 76 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 77 #define CONFIG_SYS_MEMTEST_END 0x1fffffff 78 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 79 80 #define CONFIG_SYS_CCSRBAR 0xffe00000 81 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 82 83 /* DDR Setup */ 84 #define CONFIG_SYS_FSL_DDR3 85 86 #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M 87 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 88 89 #define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) 90 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 91 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 92 93 #define CONFIG_NUM_DDR_CONTROLLERS 1 94 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 95 96 /* Default settings for DDR3 */ 97 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f 98 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 99 #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 100 #define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 101 #define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000 102 #define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 103 104 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 105 #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 106 #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 107 #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 108 109 #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 110 #define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655a608 111 #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 112 #define CONFIG_SYS_DDR_RCW_1 0x00000000 113 #define CONFIG_SYS_DDR_RCW_2 0x00000000 114 #define CONFIG_SYS_DDR_CONTROL 0xc70c0000 /* Type = DDR3 */ 115 #define CONFIG_SYS_DDR_CONTROL_2 0x04401050 116 #define CONFIG_SYS_DDR_TIMING_4 0x00220001 117 #define CONFIG_SYS_DDR_TIMING_5 0x03402400 118 119 #define CONFIG_SYS_DDR_TIMING_3 0x00020000 120 #define CONFIG_SYS_DDR_TIMING_0 0x00220004 121 #define CONFIG_SYS_DDR_TIMING_1 0x5c5b6544 122 #define CONFIG_SYS_DDR_TIMING_2 0x0fa880de 123 #define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 124 #define CONFIG_SYS_DDR_MODE_1 0x80461320 125 #define CONFIG_SYS_DDR_MODE_2 0x00008000 126 #define CONFIG_SYS_DDR_INTERVAL 0x09480000 127 128 /* 129 * Memory map 130 * 131 * 0x0000_0000 0x1fff_ffff DDR Up to 512MB cacheable 132 * 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable(PCIe * 3) 133 * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable 134 * 135 * Localbus 136 * 0xe000_0000 0xe002_0000 SSD1289 128K non-cacheable 137 * 0xec00_0000 0xefff_ffff FLASH Up to 64M non-cacheable 138 * 139 * 0xff90_0000 0xff97_ffff L2 SRAM Up to 512K cacheable 140 * 0xffd0_0000 0xffd0_3fff init ram 16K Cacheable 141 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable 142 */ 143 144 /* 145 * Local Bus Definitions 146 */ 147 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ 148 #define CONFIG_SYS_FLASH_BASE 0xec000000 149 150 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 151 152 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS)) \ 153 | BR_PS_16 | BR_V) 154 155 #define CONFIG_FLASH_OR_PRELIM 0xfc0000b1 156 157 #define CONFIG_SYS_SSD_BASE 0xe0000000 158 #define CONFIG_SYS_SSD_BASE_PHYS CONFIG_SYS_SSD_BASE 159 #define CONFIG_SSD_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_SSD_BASE_PHYS) | \ 160 BR_PS_16 | BR_V) 161 #define CONFIG_SSD_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ 162 OR_GPCM_ACS_DIV2 | OR_GPCM_SCY | \ 163 OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) 164 165 #define CONFIG_SYS_BR2_PRELIM CONFIG_SSD_BR_PRELIM 166 #define CONFIG_SYS_OR2_PRELIM CONFIG_SSD_OR_PRELIM 167 168 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} 169 #define CONFIG_SYS_FLASH_QUIET_TEST 170 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 171 172 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 173 174 #undef CONFIG_SYS_FLASH_CHECKSUM 175 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 176 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 177 178 #define CONFIG_FLASH_CFI_DRIVER 179 #define CONFIG_SYS_FLASH_CFI 180 #define CONFIG_SYS_FLASH_EMPTY_INFO 181 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 182 183 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 184 185 #define CONFIG_SYS_INIT_RAM_LOCK 186 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 187 /* Initial L1 address */ 188 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR 189 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 190 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 191 /* Size of used area in RAM */ 192 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 193 194 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 195 GENERATED_GBL_DATA_SIZE) 196 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 197 198 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 199 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */ 200 201 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 202 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 203 204 /* Serial Port 205 * open - index 2 206 * shorted - index 1 207 */ 208 #define CONFIG_CONS_INDEX 1 209 #undef CONFIG_SERIAL_SOFTWARE_FIFO 210 #define CONFIG_SYS_NS16550_SERIAL 211 #define CONFIG_SYS_NS16550_REG_SIZE 1 212 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 213 214 #define CONFIG_SYS_BAUDRATE_TABLE \ 215 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 216 217 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 218 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 219 220 /* I2C */ 221 #define CONFIG_SYS_I2C 222 #define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ 223 #define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C spd and slave address */ 224 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 225 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 226 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 227 228 /* 229 * I2C2 EEPROM 230 */ 231 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C spd and slave address */ 232 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 233 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 234 235 #define CONFIG_SYS_I2C_PCA9555_ADDR 0x23 236 237 /* enable read and write access to EEPROM */ 238 #define CONFIG_CMD_EEPROM 239 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 240 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 241 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 242 243 /* 244 * eSPI - Enhanced SPI 245 */ 246 #define CONFIG_HARD_SPI 247 248 #if defined(CONFIG_PCI) 249 /* 250 * General PCI 251 * Memory space is mapped 1-1, but I/O space must start from 0. 252 */ 253 254 /* controller 2, direct to uli, tgtid 2, Base address 9000 */ 255 #define CONFIG_SYS_PCIE2_NAME "TWR-ELEV PCIe SLOT" 256 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 257 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 258 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 259 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 260 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 261 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 262 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 263 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 264 265 /* controller 1, tgtid 1, Base address a000 */ 266 #define CONFIG_SYS_PCIE1_NAME "mini PCIe SLOT" 267 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 268 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 269 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 270 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 271 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 272 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 273 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 274 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 275 276 #define CONFIG_CMD_PCI 277 278 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 279 #define CONFIG_DOS_PARTITION 280 #endif /* CONFIG_PCI */ 281 282 #if defined(CONFIG_TSEC_ENET) 283 284 #define CONFIG_MII /* MII PHY management */ 285 #define CONFIG_TSEC1 286 #define CONFIG_TSEC1_NAME "eTSEC1" 287 #undef CONFIG_TSEC2 288 #undef CONFIG_TSEC2_NAME 289 #define CONFIG_TSEC3 290 #define CONFIG_TSEC3_NAME "eTSEC3" 291 292 #define TSEC1_PHY_ADDR 2 293 #define TSEC2_PHY_ADDR 0 294 #define TSEC3_PHY_ADDR 1 295 296 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 297 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 298 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 299 300 #define TSEC1_PHYIDX 0 301 #define TSEC2_PHYIDX 0 302 #define TSEC3_PHYIDX 0 303 304 #define CONFIG_ETHPRIME "eTSEC1" 305 306 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 307 308 #define CONFIG_HAS_ETH0 309 #define CONFIG_HAS_ETH1 310 #undef CONFIG_HAS_ETH2 311 #endif /* CONFIG_TSEC_ENET */ 312 313 #ifdef CONFIG_QE 314 /* QE microcode/firmware address */ 315 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 316 #define CONFIG_SYS_QE_FW_ADDR 0xefec0000 317 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 318 #endif /* CONFIG_QE */ 319 320 #ifdef CONFIG_TWR_P1025 321 /* 322 * QE UEC ethernet configuration 323 */ 324 #define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120) 325 326 #undef CONFIG_UEC_ETH 327 #define CONFIG_PHY_MODE_NEED_CHANGE 328 329 #define CONFIG_UEC_ETH1 /* ETH1 */ 330 #define CONFIG_HAS_ETH0 331 332 #ifdef CONFIG_UEC_ETH1 333 #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ 334 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK12 /* CLK12 for MII */ 335 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 /* CLK9 for MII */ 336 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH 337 #define CONFIG_SYS_UEC1_PHY_ADDR 0x18 /* 0x18 for MII */ 338 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII 339 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 340 #endif /* CONFIG_UEC_ETH1 */ 341 342 #define CONFIG_UEC_ETH5 /* ETH5 */ 343 #define CONFIG_HAS_ETH1 344 345 #ifdef CONFIG_UEC_ETH5 346 #define CONFIG_SYS_UEC5_UCC_NUM 4 /* UCC5 */ 347 #define CONFIG_SYS_UEC5_RX_CLK QE_CLK_NONE 348 #define CONFIG_SYS_UEC5_TX_CLK QE_CLK13 /* CLK 13 for RMII */ 349 #define CONFIG_SYS_UEC5_ETH_TYPE FAST_ETH 350 #define CONFIG_SYS_UEC5_PHY_ADDR 0x19 /* 0x19 for RMII */ 351 #define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 352 #define CONFIG_SYS_UEC5_INTERFACE_SPEED 100 353 #endif /* CONFIG_UEC_ETH5 */ 354 #endif /* CONFIG_TWR-P1025 */ 355 356 /* 357 * Dynamic MTD Partition support with mtdparts 358 */ 359 #define CONFIG_MTD_DEVICE 360 #define CONFIG_MTD_PARTITIONS 361 #define CONFIG_CMD_MTDPARTS 362 #define CONFIG_FLASH_CFI_MTD 363 #define MTDIDS_DEFAULT "nor0=ec000000.nor" 364 #define MTDPARTS_DEFAULT "mtdparts=ec000000.nor:256k(vsc7385-firmware)," \ 365 "256k(dtb),5632k(kernel),57856k(fs)," \ 366 "256k(qe-ucode-firmware),1280k(u-boot)" 367 368 /* 369 * Environment 370 */ 371 #ifdef CONFIG_SYS_RAMBOOT 372 #ifdef CONFIG_RAMBOOT_SDCARD 373 #define CONFIG_ENV_IS_IN_MMC 374 #define CONFIG_ENV_SIZE 0x2000 375 #define CONFIG_SYS_MMC_ENV_DEV 0 376 #else 377 #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ 378 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 379 #define CONFIG_ENV_SIZE 0x2000 380 #endif 381 #else 382 #define CONFIG_ENV_IS_IN_FLASH 383 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 384 #define CONFIG_ENV_SIZE 0x2000 385 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 386 #endif 387 388 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 389 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 390 391 /* 392 * Command line configuration. 393 */ 394 #define CONFIG_CMD_IRQ 395 #define CONFIG_CMD_REGINFO 396 397 /* 398 * USB 399 */ 400 #define CONFIG_HAS_FSL_DR_USB 401 402 #if defined(CONFIG_HAS_FSL_DR_USB) 403 #define CONFIG_USB_EHCI 404 405 #ifdef CONFIG_USB_EHCI 406 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 407 #define CONFIG_USB_EHCI_FSL 408 #endif 409 #endif 410 411 #ifdef CONFIG_MMC 412 #define CONFIG_FSL_ESDHC 413 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 414 #define CONFIG_GENERIC_MMC 415 #endif 416 417 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \ 418 || defined(CONFIG_FSL_SATA) 419 #define CONFIG_DOS_PARTITION 420 #endif 421 422 #undef CONFIG_WATCHDOG /* watchdog disabled */ 423 424 /* 425 * Miscellaneous configurable options 426 */ 427 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 428 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 429 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 430 #if defined(CONFIG_CMD_KGDB) 431 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 432 #else 433 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 434 #endif 435 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 436 /* Print Buffer Size */ 437 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 438 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 439 440 /* 441 * For booting Linux, the board info and command line data 442 * have to be in the first 64 MB of memory, since this is 443 * the maximum mapped by the Linux kernel during initialization. 444 */ 445 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ 446 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 447 448 /* 449 * Environment Configuration 450 */ 451 #define CONFIG_HOSTNAME unknown 452 #define CONFIG_ROOTPATH "/opt/nfsroot" 453 #define CONFIG_BOOTFILE "uImage" 454 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 455 456 /* default location for tftp and bootm */ 457 #define CONFIG_LOADADDR 1000000 458 459 #define CONFIG_BOOTARGS /* the boot command will set bootargs */ 460 461 #define CONFIG_BAUDRATE 115200 462 463 #define CONFIG_EXTRA_ENV_SETTINGS \ 464 "netdev=eth0\0" \ 465 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 466 "loadaddr=1000000\0" \ 467 "bootfile=uImage\0" \ 468 "dtbfile=twr-p1025twr.dtb\0" \ 469 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 470 "qefirmwarefile=fsl_qe_ucode_1021_10_A.bin\0" \ 471 "tftpflash=tftpboot $loadaddr $uboot; " \ 472 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 473 "erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 474 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \ 475 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 476 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \ 477 "kernelflash=tftpboot $loadaddr $bootfile; " \ 478 "protect off 0xefa80000 +$filesize; " \ 479 "erase 0xefa80000 +$filesize; " \ 480 "cp.b $loadaddr 0xefa80000 $filesize; " \ 481 "protect on 0xefa80000 +$filesize; " \ 482 "cmp.b $loadaddr 0xefa80000 $filesize\0" \ 483 "dtbflash=tftpboot $loadaddr $dtbfile; " \ 484 "protect off 0xefe80000 +$filesize; " \ 485 "erase 0xefe80000 +$filesize; " \ 486 "cp.b $loadaddr 0xefe80000 $filesize; " \ 487 "protect on 0xefe80000 +$filesize; " \ 488 "cmp.b $loadaddr 0xefe80000 $filesize\0" \ 489 "ramdiskflash=tftpboot $loadaddr $ramdiskfile; " \ 490 "protect off 0xeeb80000 +$filesize; " \ 491 "erase 0xeeb80000 +$filesize; " \ 492 "cp.b $loadaddr 0xeeb80000 $filesize; " \ 493 "protect on 0xeeb80000 +$filesize; " \ 494 "cmp.b $loadaddr 0xeeb80000 $filesize\0" \ 495 "qefirmwareflash=tftpboot $loadaddr $qefirmwarefile; " \ 496 "protect off 0xefec0000 +$filesize; " \ 497 "erase 0xefec0000 +$filesize; " \ 498 "cp.b $loadaddr 0xefec0000 $filesize; " \ 499 "protect on 0xefec0000 +$filesize; " \ 500 "cmp.b $loadaddr 0xefec0000 $filesize\0" \ 501 "consoledev=ttyS0\0" \ 502 "ramdiskaddr=2000000\0" \ 503 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 504 "fdtaddr=1e00000\0" \ 505 "bdev=sda1\0" \ 506 "norbootaddr=ef080000\0" \ 507 "norfdtaddr=ef040000\0" \ 508 "ramdisk_size=120000\0" \ 509 "usbboot=setenv bootargs root=/dev/sda1 rw rootdelay=5 " \ 510 "console=$consoledev,$baudrate $othbootargs ; bootm 0xefa80000 - 0xefe80000" 511 512 #define CONFIG_NFSBOOTCOMMAND \ 513 "setenv bootargs root=/dev/nfs rw " \ 514 "nfsroot=$serverip:$rootpath " \ 515 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 516 "console=$consoledev,$baudrate $othbootargs;" \ 517 "tftp $loadaddr $bootfile&&" \ 518 "tftp $fdtaddr $fdtfile&&" \ 519 "bootm $loadaddr - $fdtaddr" 520 521 #define CONFIG_HDBOOT \ 522 "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ 523 "console=$consoledev,$baudrate $othbootargs;" \ 524 "usb start;" \ 525 "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ 526 "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ 527 "bootm $loadaddr - $fdtaddr" 528 529 #define CONFIG_USB_FAT_BOOT \ 530 "setenv bootargs root=/dev/ram rw " \ 531 "console=$consoledev,$baudrate $othbootargs " \ 532 "ramdisk_size=$ramdisk_size;" \ 533 "usb start;" \ 534 "fatload usb 0:2 $loadaddr $bootfile;" \ 535 "fatload usb 0:2 $fdtaddr $fdtfile;" \ 536 "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ 537 "bootm $loadaddr $ramdiskaddr $fdtaddr" 538 539 #define CONFIG_USB_EXT2_BOOT \ 540 "setenv bootargs root=/dev/ram rw " \ 541 "console=$consoledev,$baudrate $othbootargs " \ 542 "ramdisk_size=$ramdisk_size;" \ 543 "usb start;" \ 544 "ext2load usb 0:4 $loadaddr $bootfile;" \ 545 "ext2load usb 0:4 $fdtaddr $fdtfile;" \ 546 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ 547 "bootm $loadaddr $ramdiskaddr $fdtaddr" 548 549 #define CONFIG_NORBOOT \ 550 "setenv bootargs root=/dev/mtdblock3 rw " \ 551 "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ 552 "bootm $norbootaddr - $norfdtaddr" 553 554 #define CONFIG_RAMBOOTCOMMAND_TFTP \ 555 "setenv bootargs root=/dev/ram rw " \ 556 "console=$consoledev,$baudrate $othbootargs " \ 557 "ramdisk_size=$ramdisk_size;" \ 558 "tftp $ramdiskaddr $ramdiskfile;" \ 559 "tftp $loadaddr $bootfile;" \ 560 "tftp $fdtaddr $fdtfile;" \ 561 "bootm $loadaddr $ramdiskaddr $fdtaddr" 562 563 #define CONFIG_RAMBOOTCOMMAND \ 564 "setenv bootargs root=/dev/ram rw " \ 565 "console=$consoledev,$baudrate $othbootargs " \ 566 "ramdisk_size=$ramdisk_size;" \ 567 "bootm 0xefa80000 0xeeb80000 0xefe80000" 568 569 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND 570 571 #endif /* __CONFIG_H */ 572