1 /* 2 * Configuration settings for the QUIPOS Cairo board. 3 * 4 * Copyright (C) DENX GmbH 5 * 6 * Author : 7 * Albert ARIBAUD <albert.aribaud@3adev.fr> 8 * 9 * Derived from EVM code by 10 * Manikandan Pillai <mani.pillai@ti.com> 11 * Itself derived from Beagle Board and 3430 SDP code by 12 * Richard Woodruff <r-woodruff2@ti.com> 13 * Syed Mohammed Khasim <khasim@ti.com> 14 * 15 * Also derived from include/configs/omap3_beagle.h 16 * 17 * SPDX-License-Identifier: GPL-2.0+ 18 */ 19 20 #ifndef __OMAP3_CAIRO_CONFIG_H 21 #define __OMAP3_CAIRO_CONFIG_H 22 23 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ 24 25 /* 26 * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM 27 * 64 bytes before this address should be set aside for u-boot.img's 28 * header. That is 0x800FFFC0--0x80100000 should not be used for any 29 * other needs. We use this rather than the inherited defines from 30 * ti_armv7_common.h for backwards compatibility. 31 */ 32 #define CONFIG_SYS_TEXT_BASE 0x80100000 33 #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE 34 #define CONFIG_SPL_BSS_START_ADDR 0x80000000 35 #define CONFIG_SPL_BSS_MAX_SIZE (512 << 10) /* 512 KB */ 36 #define CONFIG_SYS_SPL_MALLOC_START 0x80208000 37 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 38 39 #define CONFIG_NAND 40 41 #include <configs/ti_omap3_common.h> 42 43 /* 44 * Display CPU and Board information 45 */ 46 #define CONFIG_DISPLAY_BOARDINFO 1 47 48 #define CONFIG_MISC_INIT_R 49 50 #define CONFIG_REVISION_TAG 1 51 #define CONFIG_ENV_OVERWRITE 52 53 /* Enable Multi Bus support for I2C */ 54 #define CONFIG_I2C_MULTI_BUS 1 55 56 /* Probe all devices */ 57 #define CONFIG_SYS_I2C_NOPROBES { {0x0, 0x0} } 58 59 #define CONFIG_NAND 60 61 /* commands to include */ 62 #define CONFIG_CMD_NAND_LOCK_UNLOCK 63 64 /* 65 * TWL4030 66 */ 67 #define CONFIG_TWL4030_LED 1 68 69 /* 70 * Board NAND Info. 71 */ 72 #define CONFIG_NAND_OMAP_GPMC 73 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ 74 /* devices */ 75 #define CONFIG_EXTRA_ENV_SETTINGS \ 76 "machid=ffffffff\0" \ 77 "fdt_high=0x87000000\0" \ 78 "baudrate=115200\0" \ 79 "fec_addr=00:50:C2:7E:90:F0\0" \ 80 "netmask=255.255.255.0\0" \ 81 "ipaddr=192.168.2.9\0" \ 82 "gateway=192.168.2.1\0" \ 83 "serverip=192.168.2.10\0" \ 84 "nfshost=192.168.2.10\0" \ 85 "stdin=serial\0" \ 86 "stdout=serial\0" \ 87 "stderr=serial\0" \ 88 "bootargs_mmc_ramdisk=mem=128M " \ 89 "console=ttyO1,115200n8 " \ 90 "root=/dev/ram0 rw " \ 91 "initrd=0x81600000,16M " \ 92 "mpurate=600 ramdisk_size=16384 omapfb.rotate=1 " \ 93 "omapfb.rotate_type=1 omap_vout.vid1_static_vrfb_alloc=y\0" \ 94 "mmcboot=mmc init; " \ 95 "fatload mmc 0 0x80000000 uImage; " \ 96 "fatload mmc 0 0x81600000 ramdisk.gz; " \ 97 "setenv bootargs ${bootargs_mmc_ramdisk}; " \ 98 "bootm 0x80000000\0" \ 99 "bootargs_nfs=mem=99M console=ttyO0,115200n8 noinitrd rw ip=dhcp " \ 100 "root=/dev/nfs " \ 101 "nfsroot=192.168.2.10:/home/spiid/workdir/Quipos/rootfs,nolock " \ 102 "mpurate=600 omapfb.rotate=1 omapfb.rotate_type=1 " \ 103 "omap_vout.vid1_static_vrfb_alloc=y\0" \ 104 "boot_nfs=run get_kernel; setenv bootargs ${bootargs_nfs}; " \ 105 "bootm 0x80000000\0" \ 106 "bootargs_nand=mem=128M console=ttyO1,115200n8 noinitrd " \ 107 "root=/dev/mtdblock4 rw rootfstype=jffs2 mpurate=600 " \ 108 "omap_vout.vid1_static_vrfb_alloc=y omapfb.rotate=1 " \ 109 "omapfb.rotate_type=1\0" \ 110 "boot_nand=nand read.i 0x80000000 280000 300000; setenv " \ 111 "bootargs ${bootargs_nand}; bootm 0x80000000\0" \ 112 "ledorange=i2c dev 1; i2c mw 60 00 00 1; i2c mw 60 14 FF 1; " \ 113 "i2c mw 60 15 FF 1; i2c mw 60 16 FF 1; i2c mw 60 17 FF 1; " \ 114 "i2c mw 60 09 10 1; i2c mw 60 06 10 1\0" \ 115 "ledgreen=i2c dev 1; i2c mw 60 00 00 1; i2c mw 60 14 FF 1; " \ 116 "i2c mw 60 15 FF 1; i2c mw 60 16 FF 1; i2c mw 60 17 FF 1; i2c " \ 117 "mw 60 09 00 1; i2c mw 60 06 10 1\0" \ 118 "ledoff=i2c dev 1; i2c mw 60 00 00 1; i2c mw 60 14 FF 1; " \ 119 "i2c mw 60 15 FF 1; i2c mw 60 16 FF 1; i2c mw 60 17 FF 1; " \ 120 "i2c mw 60 09 00 1; i2c mw 60 06 0 1\0" \ 121 "ledred=i2c dev 1; i2c mw 60 00 00 1; i2c mw 60 14 FF 1; " \ 122 "i2c mw 60 15 FF 1; i2c mw 60 16 FF 1; i2c mw 60 17 FF 1; " \ 123 "i2c mw 60 09 10 1; i2c mw 60 06 0 1\0" \ 124 "flash_xloader=mw.b 0x81600000 0xff 0x20000; " \ 125 "nand erase 0 20000; " \ 126 "fatload mmc 0 0x81600000 MLO; " \ 127 "nandecc hw; " \ 128 "nand write.i 0x81600000 0 20000;\0" \ 129 "flash_uboot=mw.b 0x81600000 0xff 0x40000; " \ 130 "nand erase 80000 40000; " \ 131 "fatload mmc 0 0x81600000 u-boot.bin; " \ 132 "nandecc sw; " \ 133 "nand write.i 0x81600000 80000 40000;\0" \ 134 "flash_kernel=mw.b 0x81600000 0xff 0x300000; " \ 135 "nand erase 280000 300000; " \ 136 "fatload mmc 0 0x81600000 uImage; " \ 137 "nandecc sw; " \ 138 "nand write.i 0x81600000 280000 300000;\0" \ 139 "flash_rootfs=fatload mmc 0 0x81600000 rootfs.jffs2; " \ 140 "nandecc sw; " \ 141 "nand write.jffs2 0x680000 0xFF ${filesize}; " \ 142 "nand erase 680000 ${filesize}; " \ 143 "nand write.jffs2 81600000 680000 ${filesize};\0" \ 144 "flash_scrub=nand scrub; " \ 145 "run flash_xloader; " \ 146 "run flash_uboot; " \ 147 "run flash_kernel; " \ 148 "run flash_rootfs;\0" \ 149 "flash_all=run ledred; " \ 150 "nand erase.chip; " \ 151 "run ledorange; " \ 152 "run flash_xloader; " \ 153 "run flash_uboot; " \ 154 "run flash_kernel; " \ 155 "run flash_rootfs; " \ 156 "run ledgreen; " \ 157 "run boot_nand; \0" \ 158 159 #define CONFIG_BOOTCOMMAND \ 160 "if fatload mmc 0 0x81600000 MLO; then run flash_all; " \ 161 "else run boot_nand; fi" 162 163 /* 164 * OMAP3 has 12 GP timers, they can be driven by the system clock 165 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). 166 * This rate is divided by a local divisor. 167 */ 168 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 169 170 /*----------------------------------------------------------------------- 171 * FLASH and environment organization 172 */ 173 174 /* **** PISMO SUPPORT *** */ 175 #if defined(CONFIG_CMD_NAND) 176 #define CONFIG_SYS_FLASH_BASE NAND_BASE 177 #endif 178 179 /* Monitor at start of flash */ 180 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 181 #define CONFIG_SYS_ONENAND_BASE ONENAND_MAP 182 183 #define CONFIG_ENV_IS_IN_NAND 1 184 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ 185 #define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */ 186 #define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */ 187 188 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ 189 #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET 190 #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET 191 192 #define CONFIG_OMAP3_SPI 193 194 /* Defines for SPL */ 195 #define CONFIG_SPL_OMAP3_ID_NAND 196 197 /* NAND boot config */ 198 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 199 #define CONFIG_SYS_NAND_PAGE_COUNT 64 200 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 201 #define CONFIG_SYS_NAND_OOBSIZE 64 202 #define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) 203 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 204 #define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\ 205 10, 11, 12, 13} 206 #define CONFIG_SYS_NAND_ECCSIZE 512 207 #define CONFIG_SYS_NAND_ECCBYTES 3 208 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW 209 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 210 /* NAND: SPL falcon mode configs */ 211 #ifdef CONFIG_SPL_OS_BOOT 212 #define CONFIG_CMD_SPL_NAND_OFS 0x240000 213 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000 214 #define CONFIG_CMD_SPL_WRITE_SIZE 0x2000 215 #endif 216 217 /* env defaults */ 218 #define CONFIG_BOOTFILE "uImage" 219 220 /* Override OMAP3 common serial console configuration from UART3 221 * to UART2. 222 * 223 * Attention: for UART2, special MUX settings (MUX_DEFAULT(), MCBSP3) 224 * are needed and peripheral clocks for UART2 must be enabled in 225 * function per_clocks_enable(). 226 */ 227 #undef CONFIG_CONS_INDEX 228 #define CONFIG_CONS_INDEX 2 229 #ifdef CONFIG_SPL_BUILD 230 #undef CONFIG_SYS_NS16550_COM3 231 #define CONFIG_SYS_NS16550_COM2 OMAP34XX_UART2 232 #undef CONFIG_SERIAL3 233 #define CONFIG_SERIAL2 234 #endif 235 236 /* Provide MACH_TYPE for compatibility with non-DT kernels */ 237 #define MACH_TYPE_OMAP3_CAIRO 3063 238 #define CONFIG_MACH_TYPE MACH_TYPE_OMAP3_CAIRO 239 240 /*----------------------------------------------------------------------- 241 * FLASH and environment organization 242 */ 243 244 /* **** PISMO SUPPORT *** */ 245 246 #define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */ 247 /* on one chip */ 248 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */ 249 250 /*----------------------------------------------------------------------- 251 * CFI FLASH driver setup 252 */ 253 /* timeout values are in ticks */ 254 #define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ) 255 #define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ) 256 257 /* Flash banks JFFS2 should use */ 258 #define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \ 259 CONFIG_SYS_MAX_NAND_DEVICE) 260 #define CONFIG_SYS_JFFS2_MEM_NAND 261 /* use flash_info[2] */ 262 #define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS 263 #define CONFIG_SYS_JFFS2_NUM_BANKS 1 264 265 #endif /* __OMAP3_CAIRO_CONFIG_H */ 266