1 /* 2 * Copyright (C) 2012 Freescale Semiconductor, Inc. 3 * 4 * Configuration settings for the Freescale i.MX6Q SabreAuto board. 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __MX6SABREAUTO_CONFIG_H 10 #define __MX6SABREAUTO_CONFIG_H 11 12 #ifdef CONFIG_SPL 13 #include "imx6_spl.h" 14 #endif 15 16 #define CONFIG_MACH_TYPE 3529 17 #define CONFIG_MXC_UART_BASE UART4_BASE 18 #define CONSOLE_DEV "ttymxc3" 19 20 /* USB Configs */ 21 #define CONFIG_USB_ETHER_ASIX 22 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 23 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */ 24 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 25 #define CONFIG_MXC_USB_FLAGS 0 26 27 #define CONFIG_PCA953X 28 #define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x30, 8}, {0x32, 8}, {0x34, 8} } 29 30 #include "mx6sabre_common.h" 31 32 /* Falcon Mode */ 33 #ifdef CONFIG_SPL_OS_BOOT 34 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "args" 35 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" 36 #define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000 37 38 /* Falcon Mode - MMC support: args@1MB kernel@2MB */ 39 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x800 /* 1MB */ 40 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512) 41 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000 /* 2MB */ 42 #endif 43 44 #ifdef CONFIG_MTD_NOR_FLASH 45 #define CONFIG_SYS_FLASH_BASE WEIM_ARB_BASE_ADDR 46 #define CONFIG_SYS_FLASH_SECT_SIZE (128 * 1024) 47 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 48 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ 49 #define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */ 50 #define CONFIG_FLASH_CFI_DRIVER /* Use drivers/cfi_flash.c */ 51 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/ 52 #define CONFIG_SYS_FLASH_EMPTY_INFO 53 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 54 #endif 55 56 #define CONFIG_SYS_FSL_USDHC_NUM 2 57 #if defined(CONFIG_ENV_IS_IN_MMC) 58 #define CONFIG_SYS_MMC_ENV_DEV 0 59 #endif 60 61 /* I2C Configs */ 62 #define CONFIG_SYS_I2C 63 #define CONFIG_SYS_I2C_MXC 64 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 65 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 66 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 67 #define CONFIG_SYS_I2C_SPEED 100000 68 69 /* NAND stuff */ 70 #define CONFIG_NAND_MXS 71 #define CONFIG_SYS_MAX_NAND_DEVICE 1 72 #define CONFIG_SYS_NAND_BASE 0x40000000 73 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 74 #define CONFIG_SYS_NAND_ONFI_DETECTION 75 76 /* DMA stuff, needed for GPMI/MXS NAND support */ 77 #define CONFIG_APBH_DMA 78 #define CONFIG_APBH_DMA_BURST 79 #define CONFIG_APBH_DMA_BURST8 80 81 /* PMIC */ 82 #define CONFIG_POWER 83 #define CONFIG_POWER_I2C 84 #define CONFIG_POWER_PFUZE100 85 #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 86 87 #endif /* __MX6SABREAUTO_CONFIG_H */ 88