xref: /rk3399_rockchip-uboot/include/configs/mv-common.h (revision 754ae3fbb76dc429ef932bbd04b432196efe45ff)

/*
 * (C) Copyright 2010
 * Marvell Semiconductor <www.marvell.com>
 * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
 * MA 02110-1301 USA
 */

/*
 * This file contains Marvell Board Specific common defincations.
 * This file should be included in board config header file.
 *
 * It supports common definations for Kirkwood platform
 * TBD: support for Orion5X platforms
 */

#ifndef _MV_COMMON_H
#define _MV_COMMON_H

/*
 * High Level Configuration Options (easy to change)
 */
#define CONFIG_MARVELL		1
#define CONFIG_ARM926EJS	1	/* Basic Architecture */

#if defined(CONFIG_KIRKWOOD)
#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */

#define CONFIG_I2C_MVTWSI_BASE	KW_TWSI_BASE
#define MV_UART0_BASE		KW_UART0_BASE
#define MV_SATA_BASE		KW_SATA_BASE
#define MV_SATA_PORT0_OFFSET	KW_SATA_PORT0_OFFSET
#define MV_SATA_PORT1_OFFSET	KW_SATA_PORT1_OFFSET

#else
#error "Unsupported SoC"
#endif

/* additions for new ARM relocation support */
#define CONFIG_SYS_SDRAM_BASE		0x00000000
/* Kirkwood has 2k of Security SRAM, use it for SP */
#define CONFIG_SYS_INIT_SP_ADDR		0xC8012000

/*
 * CLKs configurations
 */
#define CONFIG_SYS_HZ		1000

/*
 * NS16550 Configuration
 */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
#define CONFIG_SYS_NS16550_CLK		CONFIG_SYS_TCLK
#define CONFIG_SYS_NS16550_COM1		MV_UART0_BASE

/*
 * Serial Port configuration
 * The following definitions let you select what serial you want to use
 * for your console driver.
 */

#define CONFIG_CONS_INDEX	1	/*Console on UART0 */
#define CONFIG_BAUDRATE			115200
#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, \
					  115200,230400, 460800, 921600 }
/* auto boot */
#define CONFIG_BOOTDELAY	3	/* default enable autoboot */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs  */
#define CONFIG_INITRD_TAG	1	/* enable INITRD tag */
#define CONFIG_SETUP_MEMORY_TAGS 1	/* enable memory tag */

#define	CONFIG_SYS_PROMPT	"Marvell>> "	/* Command Prompt */
#define	CONFIG_SYS_CBSIZE	1024	/* Console I/O Buff Size */
#define	CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE \
		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */

/*
 * NAND configuration
 */
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_KIRKWOOD
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define NAND_MAX_CHIPS			1
#define CONFIG_SYS_NAND_BASE		0xD8000000	/* MV_DEFADR_NANDF */
#define NAND_ALLOW_ERASE_ALL		1
#define CONFIG_SYS_64BIT_VSPRINTF	/* needed for nand_util.c */
#endif

/*
 * SPI Flash configuration
 */
#ifdef CONFIG_CMD_SF
#define CONFIG_SPI_FLASH		1
#define CONFIG_HARD_SPI			1
#define CONFIG_KIRKWOOD_SPI		1
#define CONFIG_SPI_FLASH_MACRONIX	1
#define CONFIG_ENV_SPI_BUS		0
#define CONFIG_ENV_SPI_CS		0
#define CONFIG_ENV_SPI_MAX_HZ		50000000	/*50Mhz */
#endif

/*
 * Size of malloc() pool
 */
#define CONFIG_SYS_MALLOC_LEN	(1024 * 1024) /* 1MiB for malloc() */
/* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_SIZE	128

/*
 * Other required minimal configurations
 */
#define CONFIG_SYS_LONGHELP
#define CONFIG_AUTO_COMPLETE
#define CONFIG_CMDLINE_EDITING
#define CONFIG_CONSOLE_INFO_QUIET	/* some code reduction */
#define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
#define CONFIG_ARCH_MISC_INIT	/* call arch_misc_init() */
#define CONFIG_BOARD_EARLY_INIT_F /* call board_init_f for early inits */
#define CONFIG_DISPLAY_CPUINFO	/* Display cpu info */
#define CONFIG_NR_DRAM_BANKS	4
#define CONFIG_STACKSIZE	0x00100000	/* regular stack- 1M */
#define CONFIG_SYS_LOAD_ADDR	0x00800000	/* default load adr- 8M */
#define CONFIG_SYS_MEMTEST_START 0x00400000	/* 4M */
#define CONFIG_SYS_MEMTEST_END	0x007fffff	/*(_8M -1) */
#define CONFIG_SYS_RESET_ADDRESS 0xffff0000	/* Rst Vector Adr */
#define CONFIG_SYS_MAXARGS	16	/* max number of command args */

/*
 * Ethernet Driver configuration
 */
#ifdef CONFIG_CMD_NET
#define CONFIG_CMD_MII
#define CONFIG_NETCONSOLE	/* include NetConsole support   */
#define CONFIG_NET_MULTI	/* specify more that one ports available */
#define	CONFIG_MII		/* expose smi ove miiphy interface */
#define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
#endif /* CONFIG_CMD_NET */

/*
 * USB/EHCI
 */
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_EHCI		/* Enable EHCI USB support */
#define CONFIG_USB_EHCI_KIRKWOOD
#define CONFIG_EHCI_IS_TDI
#define CONFIG_USB_STORAGE
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
#define CONFIG_SUPPORT_VFAT
#endif /* CONFIG_CMD_USB */

/*
 * IDE Support on SATA ports
 */
#ifdef CONFIG_CMD_IDE
#define __io
#define CONFIG_CMD_EXT2
#define CONFIG_MVSATA_IDE
#define CONFIG_IDE_PREINIT
#define CONFIG_MVSATA_IDE_USE_PORT1
/* Needs byte-swapping for ATA data register */
#define CONFIG_IDE_SWAP_IO
/* Data, registers and alternate blocks are at the same offset */
#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
/* Each 8-bit ATA register is aligned to a 4-bytes address */
#define CONFIG_SYS_ATA_STRIDE		4
/* Controller supports 48-bits LBA addressing */
#define CONFIG_LBA48
/* CONFIG_CMD_IDE requires some #defines for ATA registers */
#define CONFIG_SYS_IDE_MAXBUS		2
#define CONFIG_SYS_IDE_MAXDEVICE	2
/* ATA registers base is at SATA controller base */
#define CONFIG_SYS_ATA_BASE_ADDR	MV_SATA_BASE
#endif /* CONFIG_CMD_IDE */

/*
 * I2C related stuff
 */
#ifdef CONFIG_CMD_I2C
#define CONFIG_I2C_MVTWSI
#define CONFIG_SYS_I2C_SLAVE		0x0
#define CONFIG_SYS_I2C_SPEED		100000
#endif

/*
 * File system
 */
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_RBTREE
#define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
#define CONFIG_MTD_PARTITIONS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_LZO

#endif /* _MV_COMMON_H */