1 /* 2 * Copyright 2015 Freescale Semiconductor 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __LS2_RDB_H 8 #define __LS2_RDB_H 9 10 #include "ls2080a_common.h" 11 12 #undef CONFIG_CONS_INDEX 13 #define CONFIG_CONS_INDEX 2 14 15 #define I2C_MUX_CH_VOL_MONITOR 0xa 16 #define I2C_VOL_MONITOR_ADDR 0x38 17 #define CONFIG_VOL_MONITOR_IR36021_READ 18 #define CONFIG_VOL_MONITOR_IR36021_SET 19 20 #define CONFIG_VID_FLS_ENV "ls2080ardb_vdd_mv" 21 #ifndef CONFIG_SPL_BUILD 22 #define CONFIG_VID 23 #endif 24 /* step the IR regulator in 5mV increments */ 25 #define IR_VDD_STEP_DOWN 5 26 #define IR_VDD_STEP_UP 5 27 /* The lowest and highest voltage allowed for LS2080ARDB */ 28 #define VDD_MV_MIN 819 29 #define VDD_MV_MAX 1212 30 31 #ifndef __ASSEMBLY__ 32 unsigned long get_board_sys_clk(void); 33 #endif 34 35 #define CONFIG_SYS_FSL_CLK 36 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() 37 #define CONFIG_DDR_CLK_FREQ 133333333 38 #define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4) 39 40 #define CONFIG_DDR_SPD 41 #define CONFIG_DDR_ECC 42 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 43 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 44 #define SPD_EEPROM_ADDRESS1 0x51 45 #define SPD_EEPROM_ADDRESS2 0x52 46 #define SPD_EEPROM_ADDRESS3 0x53 47 #define SPD_EEPROM_ADDRESS4 0x54 48 #define SPD_EEPROM_ADDRESS5 0x55 49 #define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */ 50 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 51 #define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ 52 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 53 #define CONFIG_CHIP_SELECTS_PER_CTRL 4 54 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR 55 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1 56 #endif 57 #define CONFIG_FSL_DDR_BIST /* enable built-in memory test */ 58 59 /* SATA */ 60 #define CONFIG_LIBATA 61 #define CONFIG_SCSI_AHCI 62 #define CONFIG_SCSI_AHCI_PLAT 63 #define CONFIG_SCSI 64 #define CONFIG_DOS_PARTITION 65 #define CONFIG_BOARD_LATE_INIT 66 67 #define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 68 #define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2 69 70 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 71 #define CONFIG_SYS_SCSI_MAX_LUN 1 72 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ 73 CONFIG_SYS_SCSI_MAX_LUN) 74 #define CONFIG_PARTITION_UUIDS 75 #define CONFIG_EFI_PARTITION 76 #define CONFIG_CMD_GPT 77 78 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */ 79 80 #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) 81 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 82 #define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024) 83 84 #define CONFIG_SYS_NOR0_CSPR \ 85 (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 86 CSPR_PORT_SIZE_16 | \ 87 CSPR_MSEL_NOR | \ 88 CSPR_V) 89 #define CONFIG_SYS_NOR0_CSPR_EARLY \ 90 (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \ 91 CSPR_PORT_SIZE_16 | \ 92 CSPR_MSEL_NOR | \ 93 CSPR_V) 94 #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12) 95 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 96 FTIM0_NOR_TEADC(0x5) | \ 97 FTIM0_NOR_TEAHC(0x5)) 98 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 99 FTIM1_NOR_TRAD_NOR(0x1a) |\ 100 FTIM1_NOR_TSEQRAD_NOR(0x13)) 101 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 102 FTIM2_NOR_TCH(0x4) | \ 103 FTIM2_NOR_TWPH(0x0E) | \ 104 FTIM2_NOR_TWP(0x1c)) 105 #define CONFIG_SYS_NOR_FTIM3 0x04000000 106 #define CONFIG_SYS_IFC_CCR 0x01000000 107 108 #ifndef CONFIG_SYS_NO_FLASH 109 #define CONFIG_FLASH_CFI_DRIVER 110 #define CONFIG_SYS_FLASH_CFI 111 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 112 #define CONFIG_SYS_FLASH_QUIET_TEST 113 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 114 115 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 116 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 117 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 118 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 119 120 #define CONFIG_SYS_FLASH_EMPTY_INFO 121 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\ 122 CONFIG_SYS_FLASH_BASE + 0x40000000} 123 #endif 124 125 #define CONFIG_NAND_FSL_IFC 126 #define CONFIG_SYS_NAND_MAX_ECCPOS 256 127 #define CONFIG_SYS_NAND_MAX_OOBFREE 2 128 129 #define CONFIG_SYS_NAND_CSPR_EXT (0x0) 130 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 131 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 132 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 133 | CSPR_V) 134 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) 135 136 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 137 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 138 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 139 | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ 140 | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ 141 | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ 142 | CSOR_NAND_PB(128)) /* Pages Per Block 128*/ 143 144 #define CONFIG_SYS_NAND_ONFI_DETECTION 145 146 /* ONFI NAND Flash mode0 Timing Params */ 147 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x0e) | \ 148 FTIM0_NAND_TWP(0x30) | \ 149 FTIM0_NAND_TWCHT(0x0e) | \ 150 FTIM0_NAND_TWH(0x14)) 151 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x64) | \ 152 FTIM1_NAND_TWBE(0xab) | \ 153 FTIM1_NAND_TRR(0x1c) | \ 154 FTIM1_NAND_TRP(0x30)) 155 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x1e) | \ 156 FTIM2_NAND_TREH(0x14) | \ 157 FTIM2_NAND_TWHRE(0x3c)) 158 #define CONFIG_SYS_NAND_FTIM3 0x0 159 160 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 161 #define CONFIG_SYS_MAX_NAND_DEVICE 1 162 #define CONFIG_MTD_NAND_VERIFY_WRITE 163 #define CONFIG_CMD_NAND 164 165 #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) 166 167 #define CONFIG_FSL_QIXIS /* use common QIXIS code */ 168 #define QIXIS_LBMAP_SWITCH 0x06 169 #define QIXIS_LBMAP_MASK 0x0f 170 #define QIXIS_LBMAP_SHIFT 0 171 #define QIXIS_LBMAP_DFLTBANK 0x00 172 #define QIXIS_LBMAP_ALTBANK 0x04 173 #define QIXIS_LBMAP_NAND 0x09 174 #define QIXIS_RST_CTL_RESET 0x31 175 #define QIXIS_RST_CTL_RESET_EN 0x30 176 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 177 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 178 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 179 #define QIXIS_RCW_SRC_NAND 0x119 180 #define QIXIS_RST_FORCE_MEM 0x01 181 182 #define CONFIG_SYS_CSPR3_EXT (0x0) 183 #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \ 184 | CSPR_PORT_SIZE_8 \ 185 | CSPR_MSEL_GPCM \ 186 | CSPR_V) 187 #define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ 188 | CSPR_PORT_SIZE_8 \ 189 | CSPR_MSEL_GPCM \ 190 | CSPR_V) 191 192 #define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024) 193 #define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12) 194 /* QIXIS Timing parameters for IFC CS3 */ 195 #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 196 FTIM0_GPCM_TEADC(0x0e) | \ 197 FTIM0_GPCM_TEAHC(0x0e)) 198 #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 199 FTIM1_GPCM_TRAD(0x3f)) 200 #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ 201 FTIM2_GPCM_TCH(0xf) | \ 202 FTIM2_GPCM_TWP(0x3E)) 203 #define CONFIG_SYS_CS3_FTIM3 0x0 204 205 #if defined(CONFIG_SPL) && defined(CONFIG_NAND) 206 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT 207 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR_EARLY 208 #define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR0_CSPR 209 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK 210 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR 211 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 212 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 213 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 214 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 215 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 216 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 217 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 218 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 219 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 220 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 221 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 222 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 223 224 #define CONFIG_ENV_IS_IN_NAND 225 #define CONFIG_ENV_OFFSET (2048 * 1024) 226 #define CONFIG_ENV_SECT_SIZE 0x20000 227 #define CONFIG_ENV_SIZE 0x2000 228 #define CONFIG_SPL_PAD_TO 0x80000 229 #define CONFIG_SYS_NAND_U_BOOT_OFFS (1024 * 1024) 230 #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 * 1024) 231 #else 232 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 233 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY 234 #define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR 235 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 236 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 237 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 238 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 239 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 240 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 241 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT 242 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR 243 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK 244 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR 245 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 246 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 247 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 248 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 249 250 #define CONFIG_ENV_IS_IN_FLASH 251 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000) 252 #define CONFIG_ENV_SECT_SIZE 0x20000 253 #define CONFIG_ENV_SIZE 0x2000 254 #endif 255 256 /* Debug Server firmware */ 257 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR 258 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL 259 260 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 261 262 /* 263 * I2C 264 */ 265 #define I2C_MUX_PCA_ADDR 0x75 266 #define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/ 267 268 /* I2C bus multiplexer */ 269 #define I2C_MUX_CH_DEFAULT 0x8 270 271 /* SPI */ 272 #ifdef CONFIG_FSL_DSPI 273 #define CONFIG_SPI_FLASH 274 #define CONFIG_SPI_FLASH_BAR 275 #define CONFIG_SPI_FLASH_STMICRO 276 #endif 277 278 /* 279 * RTC configuration 280 */ 281 #define RTC 282 #define CONFIG_RTC_DS3231 1 283 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 284 #define CONFIG_CMD_DATE 285 286 /* EEPROM */ 287 #define CONFIG_ID_EEPROM 288 #define CONFIG_CMD_EEPROM 289 #define CONFIG_SYS_I2C_EEPROM_NXID 290 #define CONFIG_SYS_EEPROM_BUS_NUM 0 291 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 292 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 293 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 294 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 295 296 #define CONFIG_FSL_MEMAC 297 298 #ifdef CONFIG_PCI 299 #define CONFIG_PCI_SCAN_SHOW 300 #define CONFIG_CMD_PCI 301 #endif 302 303 /* MMC */ 304 #ifdef CONFIG_MMC 305 #define CONFIG_FSL_ESDHC 306 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 307 #define CONFIG_GENERIC_MMC 308 #define CONFIG_DOS_PARTITION 309 #endif 310 311 #define CONFIG_MISC_INIT_R 312 313 /* 314 * USB 315 */ 316 #define CONFIG_HAS_FSL_XHCI_USB 317 #define CONFIG_USB_XHCI_FSL 318 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 319 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 320 321 #undef CONFIG_CMDLINE_EDITING 322 #include <config_distro_defaults.h> 323 324 #define BOOT_TARGET_DEVICES(func) \ 325 func(USB, usb, 0) \ 326 func(MMC, mmc, 0) \ 327 func(SCSI, scsi, 0) \ 328 func(DHCP, dhcp, na) 329 #include <config_distro_bootcmd.h> 330 331 /* Initial environment variables */ 332 #undef CONFIG_EXTRA_ENV_SETTINGS 333 #define CONFIG_EXTRA_ENV_SETTINGS \ 334 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 335 "scriptaddr=0x80800000\0" \ 336 "kernel_addr_r=0x81000000\0" \ 337 "pxefile_addr_r=0x81000000\0" \ 338 "fdt_addr_r=0x88000000\0" \ 339 "ramdisk_addr_r=0x89000000\0" \ 340 "loadaddr=0x80100000\0" \ 341 "kernel_addr=0x100000\0" \ 342 "ramdisk_addr=0x800000\0" \ 343 "ramdisk_size=0x2000000\0" \ 344 "fdt_high=0xa0000000\0" \ 345 "initrd_high=0xffffffffffffffff\0" \ 346 "kernel_start=0x581100000\0" \ 347 "kernel_load=0xa0000000\0" \ 348 "kernel_size=0x2800000\0" \ 349 "fdtfile=fsl-ls2080a-rdb.dtb\0" \ 350 "mcinitcmd=fsl_mc start mc 0x580300000" \ 351 " 0x580800000 \0" \ 352 BOOTENV 353 354 #undef CONFIG_BOOTARGS 355 #define CONFIG_BOOTARGS "console=ttyS1,115200 root=/dev/ram0 " \ 356 "earlycon=uart8250,mmio,0x21c0600 " \ 357 "ramdisk_size=0x2000000 default_hugepagesz=2m" \ 358 " hugepagesz=2m hugepages=256" 359 360 #undef CONFIG_BOOTCOMMAND 361 /* Try to boot an on-NOR kernel first, then do normal distro boot */ 362 #define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580700000" \ 363 " && cp.b $kernel_start $kernel_load $kernel_size" \ 364 " && bootm $kernel_load" \ 365 " || run distro_bootcmd" 366 367 /* MAC/PHY configuration */ 368 #ifdef CONFIG_FSL_MC_ENET 369 #define CONFIG_PHYLIB_10G 370 #define CONFIG_PHY_AQUANTIA 371 #define CONFIG_PHY_CORTINA 372 #define CONFIG_PHYLIB 373 #define CONFIG_SYS_CORTINA_FW_IN_NOR 374 #define CONFIG_CORTINA_FW_ADDR 0x581000000 375 #define CONFIG_CORTINA_FW_LENGTH 0x40000 376 377 #define CORTINA_PHY_ADDR1 0x10 378 #define CORTINA_PHY_ADDR2 0x11 379 #define CORTINA_PHY_ADDR3 0x12 380 #define CORTINA_PHY_ADDR4 0x13 381 #define AQ_PHY_ADDR1 0x00 382 #define AQ_PHY_ADDR2 0x01 383 #define AQ_PHY_ADDR3 0x02 384 #define AQ_PHY_ADDR4 0x03 385 #define AQR405_IRQ_MASK 0x36 386 387 #define CONFIG_MII 388 #define CONFIG_ETHPRIME "DPMAC1@xgmii" 389 #define CONFIG_PHY_GIGE 390 #define CONFIG_PHY_AQUANTIA 391 #endif 392 393 #include <asm/fsl_secure_boot.h> 394 395 #endif /* __LS2_RDB_H */ 396