1 /* 2 * Copyright (C) 2015 Freescale Semiconductor 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __LS1043A_COMMON_H 8 #define __LS1043A_COMMON_H 9 10 #define CONFIG_REMAKE_ELF 11 #define CONFIG_FSL_LAYERSCAPE 12 #define CONFIG_FSL_LSCH2 13 #define CONFIG_LS1043A 14 #define CONFIG_MP 15 #define CONFIG_SYS_FSL_CLK 16 #define CONFIG_GICV2 17 18 #include <asm/arch/config.h> 19 #ifdef CONFIG_SYS_FSL_SRDS_1 20 #define CONFIG_SYS_HAS_SERDES 21 #endif 22 23 /* Link Definitions */ 24 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0) 25 26 #define CONFIG_SUPPORT_RAW_INITRD 27 28 #define CONFIG_SKIP_LOWLEVEL_INIT 29 #define CONFIG_BOARD_EARLY_INIT_F 1 30 31 #ifndef CONFIG_SYS_FSL_DDR4 32 #define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */ 33 #endif 34 35 #define CONFIG_VERY_BIG_RAM 36 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000 37 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 38 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 39 #define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL 40 41 #define CPU_RELEASE_ADDR secondary_boot_func 42 43 /* Generic Timer Definitions */ 44 #define COUNTER_FREQUENCY 25000000 /* 25MHz */ 45 46 /* Size of malloc() pool */ 47 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024) 48 49 /* Serial Port */ 50 #define CONFIG_CONS_INDEX 1 51 #define CONFIG_SYS_NS16550_SERIAL 52 #define CONFIG_SYS_NS16550_REG_SIZE 1 53 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)) 54 55 #define CONFIG_BAUDRATE 115200 56 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 57 58 /* SD boot SPL */ 59 #ifdef CONFIG_SD_BOOT 60 #define CONFIG_SPL_FRAMEWORK 61 #define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" 62 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 63 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT 64 #define CONFIG_SPL_WATCHDOG_SUPPORT 65 #define CONFIG_SPL_SERIAL_SUPPORT 66 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0xf0 67 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x500 68 69 #define CONFIG_SPL_TEXT_BASE 0x10000000 70 #define CONFIG_SPL_MAX_SIZE 0x1d000 71 #define CONFIG_SPL_STACK 0x1001e000 72 #define CONFIG_SPL_PAD_TO 0x1d000 73 74 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \ 75 CONFIG_SYS_MONITOR_LEN) 76 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 77 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 78 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 79 #define CONFIG_SYS_MONITOR_LEN 0xa0000 80 #endif 81 82 /* NAND SPL */ 83 #ifdef CONFIG_NAND_BOOT 84 #define CONFIG_SPL_PBL_PAD 85 #define CONFIG_SPL_FRAMEWORK 86 #define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" 87 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 88 #define CONFIG_SPL_WATCHDOG_SUPPORT 89 #define CONFIG_SPL_SERIAL_SUPPORT 90 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT 91 #define CONFIG_SPL_NAND_SUPPORT 92 #define CONFIG_SPL_TEXT_BASE 0x10000000 93 #define CONFIG_SPL_MAX_SIZE 0x1a000 94 #define CONFIG_SPL_STACK 0x1001d000 95 #define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE 96 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 97 #define CONFIG_SYS_SPL_MALLOC_START 0x80200000 98 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 99 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 100 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 101 #define CONFIG_SYS_MONITOR_LEN 0xa0000 102 #endif 103 104 /* IFC */ 105 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 106 #define CONFIG_FSL_IFC 107 /* 108 * CONFIG_SYS_FLASH_BASE has the final address (core view) 109 * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view) 110 * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address 111 * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting 112 */ 113 #define CONFIG_SYS_FLASH_BASE 0x60000000 114 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 115 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000 116 117 #ifndef CONFIG_SYS_NO_FLASH 118 #define CONFIG_FLASH_CFI_DRIVER 119 #define CONFIG_SYS_FLASH_CFI 120 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 121 #define CONFIG_SYS_FLASH_QUIET_TEST 122 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 123 #endif 124 #endif 125 126 /* I2C */ 127 #define CONFIG_SYS_I2C 128 #define CONFIG_SYS_I2C_MXC 129 #define CONFIG_SYS_I2C_MXC_I2C1 130 #define CONFIG_SYS_I2C_MXC_I2C2 131 #define CONFIG_SYS_I2C_MXC_I2C3 132 #define CONFIG_SYS_I2C_MXC_I2C4 133 134 /* PCIe */ 135 #define CONFIG_PCI /* Enable PCI/PCIE */ 136 #define CONFIG_PCIE1 /* PCIE controller 1 */ 137 #define CONFIG_PCIE2 /* PCIE controller 2 */ 138 #define CONFIG_PCIE3 /* PCIE controller 3 */ 139 #define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */ 140 #define FSL_PCIE_COMPAT "fsl,ls1043a-pcie" 141 142 #define CONFIG_SYS_PCI_64BIT 143 144 #define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000 145 #define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */ 146 #define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000 147 #define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */ 148 149 #define CONFIG_SYS_PCIE_IO_BUS 0x00000000 150 #define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000 151 #define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */ 152 153 #define CONFIG_SYS_PCIE_MEM_BUS 0x40000000 154 #define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x40000000 155 #define CONFIG_SYS_PCIE_MEM_SIZE 0x40000000 /* 1G */ 156 157 #ifdef CONFIG_PCI 158 #define CONFIG_NET_MULTI 159 #define CONFIG_PCI_PNP 160 #define CONFIG_E1000 161 #define CONFIG_PCI_SCAN_SHOW 162 #define CONFIG_CMD_PCI 163 #endif 164 165 /* Command line configuration */ 166 #define CONFIG_CMD_ENV 167 #define CONFIG_MENU 168 #define CONFIG_CMD_PXE 169 170 /* MMC */ 171 #define CONFIG_MMC 172 #ifdef CONFIG_MMC 173 #define CONFIG_FSL_ESDHC 174 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 175 #define CONFIG_GENERIC_MMC 176 #define CONFIG_DOS_PARTITION 177 #endif 178 179 /* DSPI */ 180 #define CONFIG_FSL_DSPI 181 #ifdef CONFIG_FSL_DSPI 182 #define CONFIG_DM_SPI_FLASH 183 #define CONFIG_SPI_FLASH_STMICRO /* cs0 */ 184 #define CONFIG_SPI_FLASH_SST /* cs1 */ 185 #define CONFIG_SPI_FLASH_EON /* cs2 */ 186 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 187 #define CONFIG_SF_DEFAULT_BUS 1 188 #define CONFIG_SF_DEFAULT_CS 0 189 #endif 190 #endif 191 192 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 193 194 /* FMan ucode */ 195 #define CONFIG_SYS_DPAA_FMAN 196 #ifdef CONFIG_SYS_DPAA_FMAN 197 #define CONFIG_SYS_FM_MURAM_SIZE 0x60000 198 199 #ifdef CONFIG_NAND_BOOT 200 /* Store Fman ucode at offeset 0x160000(11 blocks). */ 201 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 202 #define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE) 203 #elif defined(CONFIG_SD_BOOT) 204 /* 205 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 206 * about 1MB (2040 blocks), Env is stored after the image, and the env size is 207 * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 2080(0x820). 208 */ 209 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 210 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 211 #elif defined(CONFIG_QSPI_BOOT) 212 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 213 #define CONFIG_SYS_FMAN_FW_ADDR 0x400d0000 214 #define CONFIG_ENV_SPI_BUS 0 215 #define CONFIG_ENV_SPI_CS 0 216 #define CONFIG_ENV_SPI_MAX_HZ 1000000 217 #define CONFIG_ENV_SPI_MODE 0x03 218 #else 219 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 220 /* FMan fireware Pre-load address */ 221 #define CONFIG_SYS_FMAN_FW_ADDR 0x60300000 222 #endif 223 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 224 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 225 #endif 226 227 /* Miscellaneous configurable options */ 228 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) 229 #define CONFIG_ARCH_EARLY_INIT_R 230 #define CONFIG_BOARD_LATE_INIT 231 232 #define CONFIG_HWCONFIG 233 #define HWCONFIG_BUFFER_SIZE 128 234 235 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 236 #define MTDPARTS_DEFAULT "mtdparts=spi0.0:1m(uboot)," \ 237 "5m(kernel),1m(dtb),9m(file_system)" 238 #else 239 #define MTDPARTS_DEFAULT "mtdparts=60000000.nor:1m(nor_bank0_rcw)," \ 240 "1m(nor_bank0_uboot),1m(nor_bank0_uboot_env)," \ 241 "1m(nor_bank0_fman_uconde),40m(nor_bank0_fit)," \ 242 "1m(nor_bank4_rcw),1m(nor_bank4_uboot)," \ 243 "1m(nor_bank4_uboot_env),1m(nor_bank4_fman_ucode)," \ 244 "40m(nor_bank4_fit);7e800000.flash:" \ 245 "1m(nand_uboot),1m(nand_uboot_env)," \ 246 "20m(nand_fit);spi0.0:1m(uboot)," \ 247 "5m(kernel),1m(dtb),9m(file_system)" 248 #endif 249 250 /* Initial environment variables */ 251 #define CONFIG_EXTRA_ENV_SETTINGS \ 252 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 253 "loadaddr=0x80100000\0" \ 254 "fdt_high=0xffffffffffffffff\0" \ 255 "initrd_high=0xffffffffffffffff\0" \ 256 "kernel_start=0x61100000\0" \ 257 "kernel_load=0xa0000000\0" \ 258 "kernel_size=0x2800000\0" \ 259 "console=ttyS0,115200\0" \ 260 "mtdparts=" MTDPARTS_DEFAULT "\0" 261 262 #define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \ 263 "earlycon=uart8250,mmio,0x21c0500 " \ 264 MTDPARTS_DEFAULT 265 266 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 267 #define CONFIG_BOOTCOMMAND "sf probe && sf read $kernel_load " \ 268 "e0000 f00000 && bootm $kernel_load" 269 #else 270 #define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \ 271 "$kernel_size && bootm $kernel_load" 272 #endif 273 274 /* Monitor Command Prompt */ 275 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 276 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 277 sizeof(CONFIG_SYS_PROMPT) + 16) 278 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ 279 #define CONFIG_SYS_LONGHELP 280 #define CONFIG_CMDLINE_EDITING 1 281 #define CONFIG_AUTO_COMPLETE 282 #define CONFIG_SYS_MAXARGS 64 /* max command args */ 283 284 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 285 286 /* Hash command with SHA acceleration supported in hardware */ 287 #ifdef CONFIG_FSL_CAAM 288 #define CONFIG_CMD_HASH 289 #define CONFIG_SHA_HW_ACCEL 290 #endif 291 292 #endif /* __LS1043A_COMMON_H */ 293