1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __CONFIG_H 8 #define __CONFIG_H 9 10 #define CONFIG_ARMV7_PSCI_1_0 11 12 #define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR 13 14 #define CONFIG_SYS_FSL_CLK 15 16 #define CONFIG_SKIP_LOWLEVEL_INIT 17 #define CONFIG_DEEP_SLEEP 18 19 /* 20 * Size of malloc() pool 21 */ 22 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024) 23 24 #define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR 25 #define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE 26 27 /* 28 * USB 29 */ 30 31 /* 32 * EHCI Support - disbaled by default as 33 * there is no signal coming out of soc on 34 * this board for this controller. However, 35 * the silicon still has this controller, 36 * and anyone can use this controller by 37 * taking signals out on their board. 38 */ 39 40 /*#define CONFIG_HAS_FSL_DR_USB*/ 41 42 #ifdef CONFIG_HAS_FSL_DR_USB 43 #define CONFIG_USB_EHCI_FSL 44 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 45 #endif 46 47 /* XHCI Support - enabled by default */ 48 #define CONFIG_HAS_FSL_XHCI_USB 49 50 #ifdef CONFIG_HAS_FSL_XHCI_USB 51 #define CONFIG_USB_XHCI_FSL 52 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 53 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 54 #endif 55 56 #define CONFIG_SYS_CLK_FREQ 100000000 57 #define CONFIG_DDR_CLK_FREQ 100000000 58 59 #define DDR_SDRAM_CFG 0x470c0008 60 #define DDR_CS0_BNDS 0x008000bf 61 #define DDR_CS0_CONFIG 0x80014302 62 #define DDR_TIMING_CFG_0 0x50550004 63 #define DDR_TIMING_CFG_1 0xbcb38c56 64 #define DDR_TIMING_CFG_2 0x0040d120 65 #define DDR_TIMING_CFG_3 0x010e1000 66 #define DDR_TIMING_CFG_4 0x00000001 67 #define DDR_TIMING_CFG_5 0x03401400 68 #define DDR_SDRAM_CFG_2 0x00401010 69 #define DDR_SDRAM_MODE 0x00061c60 70 #define DDR_SDRAM_MODE_2 0x00180000 71 #define DDR_SDRAM_INTERVAL 0x18600618 72 #define DDR_DDR_WRLVL_CNTL 0x8655f605 73 #define DDR_DDR_WRLVL_CNTL_2 0x05060607 74 #define DDR_DDR_WRLVL_CNTL_3 0x05050505 75 #define DDR_DDR_CDR1 0x80040000 76 #define DDR_DDR_CDR2 0x00000001 77 #define DDR_SDRAM_CLK_CNTL 0x02000000 78 #define DDR_DDR_ZQ_CNTL 0x89080600 79 #define DDR_CS0_CONFIG_2 0 80 #define DDR_SDRAM_CFG_MEM_EN 0x80000000 81 #define SDRAM_CFG2_D_INIT 0x00000010 82 #define DDR_CDR2_VREF_TRAIN_EN 0x00000080 83 #define SDRAM_CFG2_FRC_SR 0x80000000 84 #define SDRAM_CFG_BI 0x00000001 85 86 #ifdef CONFIG_RAMBOOT_PBL 87 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1021atwr/ls102xa_pbi.cfg 88 #endif 89 90 #ifdef CONFIG_SD_BOOT 91 #ifdef CONFIG_SD_BOOT_QSPI 92 #define CONFIG_SYS_FSL_PBL_RCW \ 93 board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg 94 #else 95 #define CONFIG_SYS_FSL_PBL_RCW \ 96 board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg 97 #endif 98 #define CONFIG_SPL_FRAMEWORK 99 #define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds" 100 101 #ifdef CONFIG_SECURE_BOOT 102 /* 103 * HDR would be appended at end of image and copied to DDR along 104 * with U-Boot image. 105 */ 106 #define CONFIG_U_BOOT_HDR_SIZE (16 << 10) 107 #endif /* ifdef CONFIG_SECURE_BOOT */ 108 109 #define CONFIG_SPL_TEXT_BASE 0x10000000 110 #define CONFIG_SPL_MAX_SIZE 0x1a000 111 #define CONFIG_SPL_STACK 0x1001d000 112 #define CONFIG_SPL_PAD_TO 0x1c000 113 #define CONFIG_SYS_TEXT_BASE 0x82000000 114 115 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \ 116 CONFIG_SYS_MONITOR_LEN) 117 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 118 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 119 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 120 121 #ifdef CONFIG_U_BOOT_HDR_SIZE 122 /* 123 * HDR would be appended at end of image and copied to DDR along 124 * with U-Boot image. Here u-boot max. size is 512K. So if binary 125 * size increases then increase this size in case of secure boot as 126 * it uses raw u-boot image instead of fit image. 127 */ 128 #define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE) 129 #else 130 #define CONFIG_SYS_MONITOR_LEN 0x100000 131 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */ 132 #endif 133 134 #ifdef CONFIG_QSPI_BOOT 135 #define CONFIG_SYS_TEXT_BASE 0x40100000 136 #endif 137 138 #ifndef CONFIG_SYS_TEXT_BASE 139 #define CONFIG_SYS_TEXT_BASE 0x60100000 140 #endif 141 142 #define CONFIG_NR_DRAM_BANKS 1 143 #define PHYS_SDRAM 0x80000000 144 #define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) 145 146 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL 147 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 148 149 #if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \ 150 !defined(CONFIG_QSPI_BOOT) 151 #define CONFIG_U_QE 152 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 153 #endif 154 155 /* 156 * IFC Definitions 157 */ 158 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 159 #define CONFIG_FSL_IFC 160 #define CONFIG_SYS_FLASH_BASE 0x60000000 161 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 162 163 #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) 164 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 165 CSPR_PORT_SIZE_16 | \ 166 CSPR_MSEL_NOR | \ 167 CSPR_V) 168 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) 169 170 /* NOR Flash Timing Params */ 171 #define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ 172 CSOR_NOR_TRHZ_80) 173 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 174 FTIM0_NOR_TEADC(0x5) | \ 175 FTIM0_NOR_TAVDS(0x0) | \ 176 FTIM0_NOR_TEAHC(0x5)) 177 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 178 FTIM1_NOR_TRAD_NOR(0x1A) | \ 179 FTIM1_NOR_TSEQRAD_NOR(0x13)) 180 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 181 FTIM2_NOR_TCH(0x4) | \ 182 FTIM2_NOR_TWP(0x1c) | \ 183 FTIM2_NOR_TWPH(0x0e)) 184 #define CONFIG_SYS_NOR_FTIM3 0 185 186 #define CONFIG_FLASH_CFI_DRIVER 187 #define CONFIG_SYS_FLASH_CFI 188 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 189 #define CONFIG_SYS_FLASH_QUIET_TEST 190 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 191 192 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 193 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 194 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 195 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 196 197 #define CONFIG_SYS_FLASH_EMPTY_INFO 198 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS } 199 200 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS 201 #define CONFIG_SYS_WRITE_SWAPPED_DATA 202 #endif 203 204 /* CPLD */ 205 206 #define CONFIG_SYS_CPLD_BASE 0x7fb00000 207 #define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE 208 209 #define CONFIG_SYS_FPGA_CSPR_EXT (0x0) 210 #define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \ 211 CSPR_PORT_SIZE_8 | \ 212 CSPR_MSEL_GPCM | \ 213 CSPR_V) 214 #define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024) 215 #define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ 216 CSOR_NOR_NOR_MODE_AVD_NOR | \ 217 CSOR_NOR_TRHZ_80) 218 219 /* CPLD Timing parameters for IFC GPCM */ 220 #define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xf) | \ 221 FTIM0_GPCM_TEADC(0xf) | \ 222 FTIM0_GPCM_TEAHC(0xf)) 223 #define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 224 FTIM1_GPCM_TRAD(0x3f)) 225 #define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ 226 FTIM2_GPCM_TCH(0xf) | \ 227 FTIM2_GPCM_TWP(0xff)) 228 #define CONFIG_SYS_FPGA_FTIM3 0x0 229 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 230 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 231 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 232 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 233 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 234 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 235 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 236 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 237 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_FPGA_CSPR_EXT 238 #define CONFIG_SYS_CSPR1 CONFIG_SYS_FPGA_CSPR 239 #define CONFIG_SYS_AMASK1 CONFIG_SYS_FPGA_AMASK 240 #define CONFIG_SYS_CSOR1 CONFIG_SYS_FPGA_CSOR 241 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_FPGA_FTIM0 242 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_FPGA_FTIM1 243 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_FPGA_FTIM2 244 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_FPGA_FTIM3 245 246 /* 247 * Serial Port 248 */ 249 #ifdef CONFIG_LPUART 250 #define CONFIG_LPUART_32B_REG 251 #else 252 #define CONFIG_CONS_INDEX 1 253 #define CONFIG_SYS_NS16550_SERIAL 254 #ifndef CONFIG_DM_SERIAL 255 #define CONFIG_SYS_NS16550_REG_SIZE 1 256 #endif 257 #define CONFIG_SYS_NS16550_CLK get_serial_clock() 258 #endif 259 260 /* 261 * I2C 262 */ 263 #define CONFIG_SYS_I2C 264 #define CONFIG_SYS_I2C_MXC 265 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 266 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 267 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 268 269 /* EEPROM */ 270 #define CONFIG_ID_EEPROM 271 #define CONFIG_SYS_I2C_EEPROM_NXID 272 #define CONFIG_SYS_EEPROM_BUS_NUM 1 273 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 274 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 275 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 276 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 277 278 /* 279 * MMC 280 */ 281 #define CONFIG_FSL_ESDHC 282 283 /* SPI */ 284 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 285 /* QSPI */ 286 #define QSPI0_AMBA_BASE 0x40000000 287 #define FSL_QSPI_FLASH_SIZE (1 << 24) 288 #define FSL_QSPI_FLASH_NUM 2 289 290 /* DSPI */ 291 #endif 292 293 /* DM SPI */ 294 #if defined(CONFIG_FSL_DSPI) || defined(CONFIG_FSL_QSPI) 295 #define CONFIG_DM_SPI_FLASH 296 #endif 297 298 /* 299 * Video 300 */ 301 #ifdef CONFIG_VIDEO_FSL_DCU_FB 302 #define CONFIG_VIDEO_LOGO 303 #define CONFIG_VIDEO_BMP_LOGO 304 305 #define CONFIG_FSL_DCU_SII9022A 306 #define CONFIG_SYS_I2C_DVI_BUS_NUM 1 307 #define CONFIG_SYS_I2C_DVI_ADDR 0x39 308 #endif 309 310 /* 311 * eTSEC 312 */ 313 #define CONFIG_TSEC_ENET 314 315 #ifdef CONFIG_TSEC_ENET 316 #define CONFIG_MII 317 #define CONFIG_MII_DEFAULT_TSEC 1 318 #define CONFIG_TSEC1 1 319 #define CONFIG_TSEC1_NAME "eTSEC1" 320 #define CONFIG_TSEC2 1 321 #define CONFIG_TSEC2_NAME "eTSEC2" 322 #define CONFIG_TSEC3 1 323 #define CONFIG_TSEC3_NAME "eTSEC3" 324 325 #define TSEC1_PHY_ADDR 2 326 #define TSEC2_PHY_ADDR 0 327 #define TSEC3_PHY_ADDR 1 328 329 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 330 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 331 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 332 333 #define TSEC1_PHYIDX 0 334 #define TSEC2_PHYIDX 0 335 #define TSEC3_PHYIDX 0 336 337 #define CONFIG_ETHPRIME "eTSEC1" 338 339 #define CONFIG_PHY_GIGE 340 #define CONFIG_PHYLIB 341 #define CONFIG_PHY_ATHEROS 342 343 #define CONFIG_HAS_ETH0 344 #define CONFIG_HAS_ETH1 345 #define CONFIG_HAS_ETH2 346 #endif 347 348 /* PCIe */ 349 #define CONFIG_PCIE1 /* PCIE controller 1 */ 350 #define CONFIG_PCIE2 /* PCIE controller 2 */ 351 352 #ifdef CONFIG_PCI 353 #define CONFIG_PCI_SCAN_SHOW 354 #define CONFIG_CMD_PCI 355 #endif 356 357 #define CONFIG_CMDLINE_TAG 358 359 #define CONFIG_PEN_ADDR_BIG_ENDIAN 360 #define CONFIG_LAYERSCAPE_NS_ACCESS 361 #define CONFIG_SMP_PEN_ADDR 0x01ee0200 362 #define COUNTER_FREQUENCY 12500000 363 364 #define CONFIG_HWCONFIG 365 #define HWCONFIG_BUFFER_SIZE 256 366 367 #define CONFIG_FSL_DEVICE_DISABLE 368 369 #include <config_distro_defaults.h> 370 #define BOOT_TARGET_DEVICES(func) \ 371 func(MMC, mmc, 0) \ 372 func(USB, usb, 0) 373 #include <config_distro_bootcmd.h> 374 375 #ifdef CONFIG_LPUART 376 #define CONFIG_EXTRA_ENV_SETTINGS \ 377 "bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \ 378 "initrd_high=0xffffffff\0" \ 379 "fdt_high=0xffffffff\0" \ 380 "fdt_addr=0x64f00000\0" \ 381 "kernel_addr=0x65000000\0" \ 382 "scriptaddr=0x80000000\0" \ 383 "fdtheader_addr_r=0x80100000\0" \ 384 "kernelheader_addr_r=0x80200000\0" \ 385 "kernel_addr_r=0x81000000\0" \ 386 "fdt_addr_r=0x90000000\0" \ 387 "ramdisk_addr_r=0xa0000000\0" \ 388 "load_addr=0xa0000000\0" \ 389 "kernel_size=0x2800000\0" \ 390 BOOTENV \ 391 "boot_scripts=ls1021atwr_boot.scr\0" \ 392 "scan_dev_for_boot_part=" \ 393 "part list ${devtype} ${devnum} devplist; " \ 394 "env exists devplist || setenv devplist 1; " \ 395 "for distro_bootpart in ${devplist}; do " \ 396 "if fstype ${devtype} " \ 397 "${devnum}:${distro_bootpart} " \ 398 "bootfstype; then " \ 399 "run scan_dev_for_boot; " \ 400 "fi; " \ 401 "done\0" \ 402 "installer=load mmc 0:2 $load_addr " \ 403 "/flex_installer_arm32.itb; " \ 404 "bootm $load_addr#ls1021atwr\0" \ 405 "qspi_bootcmd=echo Trying load from qspi..;" \ 406 "sf probe && sf read $load_addr " \ 407 "$kernel_addr $kernel_size && bootm $load_addr#$board\0" \ 408 "nor_bootcmd=echo Trying load from nor..;" \ 409 "cp.b $kernel_addr $load_addr " \ 410 "$kernel_size && bootm $load_addr#$board\0" 411 #else 412 #define CONFIG_EXTRA_ENV_SETTINGS \ 413 "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \ 414 "initrd_high=0xffffffff\0" \ 415 "fdt_high=0xffffffff\0" \ 416 "fdt_addr=0x64f00000\0" \ 417 "kernel_addr=0x65000000\0" \ 418 "scriptaddr=0x80000000\0" \ 419 "fdtheader_addr_r=0x80100000\0" \ 420 "kernelheader_addr_r=0x80200000\0" \ 421 "kernel_addr_r=0x81000000\0" \ 422 "fdt_addr_r=0x90000000\0" \ 423 "ramdisk_addr_r=0xa0000000\0" \ 424 "load_addr=0xa0000000\0" \ 425 "kernel_size=0x2800000\0" \ 426 BOOTENV \ 427 "boot_scripts=ls1021atwr_boot.scr\0" \ 428 "scan_dev_for_boot_part=" \ 429 "part list ${devtype} ${devnum} devplist; " \ 430 "env exists devplist || setenv devplist 1; " \ 431 "for distro_bootpart in ${devplist}; do " \ 432 "if fstype ${devtype} " \ 433 "${devnum}:${distro_bootpart} " \ 434 "bootfstype; then " \ 435 "run scan_dev_for_boot; " \ 436 "fi; " \ 437 "done\0" \ 438 "installer=load mmc 0:2 $load_addr " \ 439 "/flex_installer_arm32.itb; " \ 440 "bootm $load_addr#ls1021atwr\0" \ 441 "qspi_bootcmd=echo Trying load from qspi..;" \ 442 "sf probe && sf read $load_addr " \ 443 "$kernel_addr $kernel_size && bootm $load_addr#$board\0" \ 444 "nor_bootcmd=echo Trying load from nor..;" \ 445 "cp.b $kernel_addr $load_addr " \ 446 "$kernel_size && bootm $load_addr#$board\0" 447 #endif 448 449 #undef CONFIG_BOOTCOMMAND 450 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 451 #define CONFIG_BOOTCOMMAND "run distro_bootcmd;run qspi_bootcmd" 452 #else 453 #define CONFIG_BOOTCOMMAND "run distro_bootcmd;run nor_bootcmd" 454 #endif 455 456 #define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0" 457 458 /* 459 * Miscellaneous configurable options 460 */ 461 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 462 #define CONFIG_AUTO_COMPLETE 463 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 464 #define CONFIG_SYS_PBSIZE \ 465 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 466 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 467 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 468 469 #define CONFIG_SYS_MEMTEST_START 0x80000000 470 #define CONFIG_SYS_MEMTEST_END 0x9fffffff 471 472 #define CONFIG_SYS_LOAD_ADDR 0x82000000 473 474 #define CONFIG_LS102XA_STREAM_ID 475 476 #define CONFIG_SYS_INIT_SP_OFFSET \ 477 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 478 #define CONFIG_SYS_INIT_SP_ADDR \ 479 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 480 481 #ifdef CONFIG_SPL_BUILD 482 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 483 #else 484 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 485 #endif 486 487 #define CONFIG_SYS_QE_FW_ADDR 0x60940000 488 489 /* 490 * Environment 491 */ 492 #define CONFIG_ENV_OVERWRITE 493 494 #if defined(CONFIG_SD_BOOT) 495 #define CONFIG_ENV_OFFSET 0x300000 496 #define CONFIG_SYS_MMC_ENV_DEV 0 497 #define CONFIG_ENV_SIZE 0x20000 498 #elif defined(CONFIG_QSPI_BOOT) 499 #define CONFIG_ENV_SIZE 0x2000 500 #define CONFIG_ENV_OFFSET 0x300000 501 #define CONFIG_ENV_SECT_SIZE 0x10000 502 #else 503 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000) 504 #define CONFIG_ENV_SIZE 0x20000 505 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 506 #endif 507 508 #define CONFIG_MISC_INIT_R 509 510 #include <asm/fsl_secure_boot.h> 511 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 512 513 #endif 514