xref: /rk3399_rockchip-uboot/include/configs/ls1021atwr.h (revision 03544c6640e8a969f8409eac637f4780e1eabb1d)

/*
 * Copyright 2014 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_LS102XA

#define CONFIG_ARMV7_PSCI

#define CONFIG_SYS_GENERIC_BOARD

#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO

#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_DEEP_SLEEP
#ifdef CONFIG_DEEP_SLEEP
#define CONFIG_SILENT_CONSOLE
#endif

/*
 * Size of malloc() pool
 */
#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 16 * 1024 * 1024)

#define CONFIG_SYS_INIT_RAM_ADDR	OCRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE	OCRAM_SIZE

/*
 * USB
 */

/*
 * EHCI Support - disbaled by default as
 * there is no signal coming out of soc on
 * this board for this controller. However,
 * the silicon still has this controller,
 * and anyone can use this controller by
 * taking signals out on their board.
 */

/*#define CONFIG_HAS_FSL_DR_USB*/

#ifdef CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif

/* XHCI Support - enabled by default */
#define CONFIG_HAS_FSL_XHCI_USB

#ifdef CONFIG_HAS_FSL_XHCI_USB
#define CONFIG_USB_XHCI_FSL
#define CONFIG_USB_XHCI_DWC3
#define CONFIG_USB_XHCI
#define CONFIG_USB_MAX_CONTROLLER_COUNT        1
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS     2
#endif

#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_XHCI_USB)
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
#define CONFIG_CMD_EXT2
#endif

/*
 * Generic Timer Definitions
 */
#define GENERIC_TIMER_CLK		12500000

#define CONFIG_SYS_CLK_FREQ		100000000
#define CONFIG_DDR_CLK_FREQ		100000000

#define DDR_SDRAM_CFG			0x470c0008
#define DDR_CS0_BNDS			0x008000bf
#define DDR_CS0_CONFIG			0x80014302
#define DDR_TIMING_CFG_0		0x50550004
#define DDR_TIMING_CFG_1		0xbcb38c56
#define DDR_TIMING_CFG_2		0x0040d120
#define DDR_TIMING_CFG_3		0x010e1000
#define DDR_TIMING_CFG_4		0x00000001
#define DDR_TIMING_CFG_5		0x03401400
#define DDR_SDRAM_CFG_2			0x00401010
#define DDR_SDRAM_MODE			0x00061c60
#define DDR_SDRAM_MODE_2		0x00180000
#define DDR_SDRAM_INTERVAL		0x18600618
#define DDR_DDR_WRLVL_CNTL		0x8655f605
#define DDR_DDR_WRLVL_CNTL_2		0x05060607
#define DDR_DDR_WRLVL_CNTL_3		0x05050505
#define DDR_DDR_CDR1			0x80040000
#define DDR_DDR_CDR2			0x00000001
#define DDR_SDRAM_CLK_CNTL		0x02000000
#define DDR_DDR_ZQ_CNTL			0x89080600
#define DDR_CS0_CONFIG_2		0
#define DDR_SDRAM_CFG_MEM_EN		0x80000000
#define SDRAM_CFG2_D_INIT		0x00000010
#define DDR_CDR2_VREF_TRAIN_EN		0x00000080
#define SDRAM_CFG2_FRC_SR		0x80000000
#define SDRAM_CFG_BI			0x00000001

#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI	board/freescale/ls1021atwr/ls102xa_pbi.cfg
#endif

#ifdef CONFIG_SD_BOOT
#define CONFIG_SYS_FSL_PBL_RCW	board/freescale/ls1021atwr/ls102xa_rcw_sd.cfg
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_LDSCRIPT	"arch/$(ARCH)/cpu/u-boot-spl.lds"
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_WATCHDOG_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR		0xe8
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS		0x400

#define CONFIG_SPL_TEXT_BASE		0x10000000
#define CONFIG_SPL_MAX_SIZE		0x1a000
#define CONFIG_SPL_STACK		0x1001d000
#define CONFIG_SPL_PAD_TO		0x1c000
#define CONFIG_SYS_TEXT_BASE		0x82000000

#define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SYS_TEXT_BASE + \
		CONFIG_SYS_MONITOR_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
#define CONFIG_SPL_BSS_START_ADDR	0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE		0x80000
#define CONFIG_SYS_MONITOR_LEN		0x80000
#endif

#ifdef CONFIG_QSPI_BOOT
#define CONFIG_SYS_TEXT_BASE		0x40010000
#define CONFIG_SYS_NO_FLASH
#endif

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE		0x60100000
#endif

#define CONFIG_NR_DRAM_BANKS		1
#define PHYS_SDRAM			0x80000000
#define PHYS_SDRAM_SIZE			(1u * 1024 * 1024 * 1024)

#define CONFIG_SYS_DDR_SDRAM_BASE      0x80000000UL
#define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE

#define CONFIG_SYS_HAS_SERDES

#define CONFIG_FSL_CAAM			/* Enable CAAM */

#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \
	!defined(CONFIG_QSPI_BOOT)
#define CONFIG_U_QE
#endif

/*
 * IFC Definitions
 */
#ifndef CONFIG_QSPI_BOOT
#define CONFIG_FSL_IFC
#define CONFIG_SYS_FLASH_BASE		0x60000000
#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE

#define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
#define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
				CSPR_PORT_SIZE_16 | \
				CSPR_MSEL_NOR | \
				CSPR_V)
#define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)

/* NOR Flash Timing Params */
#define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
					CSOR_NOR_TRHZ_80)
#define CONFIG_SYS_NOR_FTIM0		(FTIM0_NOR_TACSE(0x4) | \
					FTIM0_NOR_TEADC(0x5) | \
					FTIM0_NOR_TAVDS(0x0) | \
					FTIM0_NOR_TEAHC(0x5))
#define CONFIG_SYS_NOR_FTIM1		(FTIM1_NOR_TACO(0x35) | \
					FTIM1_NOR_TRAD_NOR(0x1A) | \
					FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CONFIG_SYS_NOR_FTIM2		(FTIM2_NOR_TCS(0x4) | \
					FTIM2_NOR_TCH(0x4) | \
					FTIM2_NOR_TWP(0x1c) | \
					FTIM2_NOR_TWPH(0x0e))
#define CONFIG_SYS_NOR_FTIM3		0

#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */

#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE_PHYS }

#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
#define CONFIG_SYS_WRITE_SWAPPED_DATA
#endif

/* CPLD */

#define CONFIG_SYS_CPLD_BASE	0x7fb00000
#define CPLD_BASE_PHYS		CONFIG_SYS_CPLD_BASE

#define CONFIG_SYS_FPGA_CSPR_EXT        (0x0)
#define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \
					CSPR_PORT_SIZE_8 | \
					CSPR_MSEL_GPCM | \
					CSPR_V)
#define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64 * 1024)
#define CONFIG_SYS_FPGA_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
					CSOR_NOR_NOR_MODE_AVD_NOR | \
					CSOR_NOR_TRHZ_80)

/* CPLD Timing parameters for IFC GPCM */
#define CONFIG_SYS_FPGA_FTIM0		(FTIM0_GPCM_TACSE(0xf) | \
					FTIM0_GPCM_TEADC(0xf) | \
					FTIM0_GPCM_TEAHC(0xf))
#define CONFIG_SYS_FPGA_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
					FTIM1_GPCM_TRAD(0x3f))
#define CONFIG_SYS_FPGA_FTIM2		(FTIM2_GPCM_TCS(0xf) | \
					FTIM2_GPCM_TCH(0xf) | \
					FTIM2_GPCM_TWP(0xff))
#define CONFIG_SYS_FPGA_FTIM3           0x0
#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_FPGA_CSPR_EXT
#define CONFIG_SYS_CSPR1		CONFIG_SYS_FPGA_CSPR
#define CONFIG_SYS_AMASK1		CONFIG_SYS_FPGA_AMASK
#define CONFIG_SYS_CSOR1		CONFIG_SYS_FPGA_CSOR
#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_FPGA_FTIM0
#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_FPGA_FTIM1
#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_FPGA_FTIM2
#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_FPGA_FTIM3

/*
 * Serial Port
 */
#ifdef CONFIG_LPUART
#define CONFIG_FSL_LPUART
#define CONFIG_LPUART_32B_REG
#else
#define CONFIG_CONS_INDEX		1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
#endif

#define CONFIG_BAUDRATE			115200

/*
 * I2C
 */
#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */

/* EEPROM */
#ifndef CONFIG_SD_BOOT
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM		1
#define CONFIG_SYS_I2C_EEPROM_ADDR		0x53
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
#endif

/*
 * MMC
 */
#define CONFIG_MMC
#define CONFIG_CMD_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_GENERIC_MMC

#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION

/* SPI */
#ifdef CONFIG_QSPI_BOOT
/* QSPI */
#define CONFIG_FSL_QSPI
#define QSPI0_AMBA_BASE			0x40000000
#define FSL_QSPI_FLASH_SIZE		(1 << 24)
#define FSL_QSPI_FLASH_NUM		2
#define CONFIG_SPI_FLASH_STMICRO

/* DM SPI */
#if defined(CONFIG_FSL_DSPI) || defined(CONFIG_FSL_QSPI)
#define CONFIG_CMD_SF
#define CONFIG_DM_SPI_FLASH
#endif
#endif

/*
 * Video
 */
#define CONFIG_FSL_DCU_FB

#ifdef CONFIG_FSL_DCU_FB
#define CONFIG_VIDEO
#define CONFIG_CMD_BMP
#define CONFIG_CFB_CONSOLE
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO

#define CONFIG_FSL_DCU_SII9022A
#define CONFIG_SYS_I2C_DVI_BUS_NUM	1
#define CONFIG_SYS_I2C_DVI_ADDR		0x39
#endif

/*
 * eTSEC
 */
#define CONFIG_TSEC_ENET

#ifdef CONFIG_TSEC_ENET
#define CONFIG_MII
#define CONFIG_MII_DEFAULT_TSEC		1
#define CONFIG_TSEC1			1
#define CONFIG_TSEC1_NAME		"eTSEC1"
#define CONFIG_TSEC2			1
#define CONFIG_TSEC2_NAME		"eTSEC2"
#define CONFIG_TSEC3			1
#define CONFIG_TSEC3_NAME		"eTSEC3"

#define TSEC1_PHY_ADDR			2
#define TSEC2_PHY_ADDR			0
#define TSEC3_PHY_ADDR			1

#define TSEC1_FLAGS			(TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_FLAGS			(TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC3_FLAGS			(TSEC_GIGABIT | TSEC_REDUCED)

#define TSEC1_PHYIDX			0
#define TSEC2_PHYIDX			0
#define TSEC3_PHYIDX			0

#define CONFIG_ETHPRIME			"eTSEC1"

#define CONFIG_PHY_GIGE
#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS

#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#endif

/* PCIe */
#define CONFIG_PCI		/* Enable PCI/PCIE */
#define CONFIG_PCIE1		/* PCIE controler 1 */
#define CONFIG_PCIE2		/* PCIE controler 2 */
#define CONFIG_PCIE_LAYERSCAPE	/* Use common FSL Layerscape PCIe code */
#define FSL_PCIE_COMPAT "fsl,ls1021a-pcie"

#define CONFIG_SYS_PCI_64BIT

#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF	0x00000000
#define CONFIG_SYS_PCIE_CFG0_SIZE	0x00001000	/* 4k */
#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF	0x00001000
#define CONFIG_SYS_PCIE_CFG1_SIZE	0x00001000	/* 4k */

#define CONFIG_SYS_PCIE_IO_BUS		0x00000000
#define CONFIG_SYS_PCIE_IO_PHYS_OFF	0x00010000
#define CONFIG_SYS_PCIE_IO_SIZE		0x00010000	/* 64k */

#define CONFIG_SYS_PCIE_MEM_BUS		0x08000000
#define CONFIG_SYS_PCIE_MEM_PHYS_OFF	0x04000000
#define CONFIG_SYS_PCIE_MEM_SIZE	0x08000000	/* 128M */

#ifdef CONFIG_PCI
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_CMD_PCI
#endif

#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII

#define CONFIG_CMDLINE_TAG
#define CONFIG_CMDLINE_EDITING

#define CONFIG_ARMV7_NONSEC
#define CONFIG_ARMV7_VIRT
#define CONFIG_PEN_ADDR_BIG_ENDIAN
#define CONFIG_LS102XA_NS_ACCESS
#define CONFIG_SMP_PEN_ADDR		0x01ee0200
#define CONFIG_TIMER_CLK_FREQ		12500000

#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE		256

#define CONFIG_FSL_DEVICE_DISABLE

#define CONFIG_BOOTDELAY		3

#ifdef CONFIG_LPUART
#define CONFIG_EXTRA_ENV_SETTINGS       \
	"bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \
	"initrd_high=0xcfffffff\0"      \
	"fdt_high=0xcfffffff\0"
#else
#define CONFIG_EXTRA_ENV_SETTINGS	\
	"bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
	"initrd_high=0xcfffffff\0"      \
	"fdt_high=0xcfffffff\0"
#endif

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP		/* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE		\
		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE

#define CONFIG_CMD_GREPENV
#define CONFIG_CMD_MEMINFO
#define CONFIG_CMD_MEMTEST
#define CONFIG_SYS_MEMTEST_START	0x80000000
#define CONFIG_SYS_MEMTEST_END		0x9fffffff

#define CONFIG_SYS_LOAD_ADDR		0x82000000

#define CONFIG_LS102XA_STREAM_ID

/*
 * Stack sizes
 * The stack sizes are set up in start.S using the settings below
 */
#define CONFIG_STACKSIZE		(30 * 1024)

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
#endif

#define CONFIG_SYS_QE_FW_ADDR     0x67f40000

/*
 * Environment
 */
#define CONFIG_ENV_OVERWRITE

#if defined(CONFIG_SD_BOOT)
#define CONFIG_ENV_OFFSET		0x100000
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV		0
#define CONFIG_ENV_SIZE			0x20000
#elif defined(CONFIG_QSPI_BOOT)
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE			0x2000
#define CONFIG_ENV_OFFSET		0x100000
#define CONFIG_ENV_SECT_SIZE		0x10000
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE			0x20000
#define CONFIG_ENV_SECT_SIZE		0x20000 /* 128K (one sector) */
#endif

#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_CMD_BOOTZ

#define CONFIG_MISC_INIT_R

/* Hash command with SHA acceleration supported in hardware */
#define CONFIG_CMD_HASH
#define CONFIG_SHA_HW_ACCEL

#ifdef CONFIG_SECURE_BOOT
#define CONFIG_CMD_BLOB
#include <asm/fsl_secure_boot.h>
#endif

#endif