1 /* 2 * Configuation settings for the Sentec Cobra Board. 3 * 4 * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 /* --- 10 * Version: U-Boot 1.0.0 - initial release for Sentec COBRA5272 board 11 * Date: 2004-03-29 12 * Author: Florian Schlote 13 * 14 * For a description of configuration options please refer also to the 15 * general u-boot-1.x.x/README file 16 * --- 17 */ 18 19 /* --- 20 * board/config.h - configuration options, board specific 21 * --- 22 */ 23 24 #ifndef _CONFIG_COBRA5272_H 25 #define _CONFIG_COBRA5272_H 26 27 /* --- 28 * Defines processor clock - important for correct timings concerning serial 29 * interface etc. 30 * --- 31 */ 32 33 #define CONFIG_SYS_CLK 66000000 34 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ 35 36 /* --- 37 * Enable use of Ethernet 38 * --- 39 */ 40 #define CONFIG_MCFFEC 41 42 /* Enable Dma Timer */ 43 #define CONFIG_MCFTMR 44 45 /* --- 46 * Define baudrate for UART1 (console output, tftp, ...) 47 * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud 48 * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command 49 * interface 50 * --- 51 */ 52 53 #define CONFIG_MCFUART 54 #define CONFIG_SYS_UART_PORT (0) 55 56 /* --- 57 * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change 58 * timeout acc. to your needs 59 * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000 60 * for 10 sec 61 * --- 62 */ 63 64 #if 0 65 #define CONFIG_WATCHDOG 66 #define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */ 67 #endif 68 69 /* --- 70 * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different 71 * bootloader residing in flash ('chainloading'); if you want to use 72 * chainloading or want to compile a u-boot binary that can be loaded into 73 * RAM via BDM set 74 * "#if 0" to "#if 1" 75 * You will need a first stage bootloader then, e. g. colilo or a working BDM 76 * cable (Background Debug Mode) 77 * 78 * Setting #if 0: u-boot will start from flash and relocate itself to RAM 79 * 80 * Please do not forget to modify the setting of CONFIG_SYS_TEXT_BASE 81 * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000) 82 * 83 * --- 84 */ 85 86 #if 0 87 #define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */ 88 #endif 89 90 /* --- 91 * Configuration for environment 92 * Environment is embedded in u-boot in the second sector of the flash 93 * --- 94 */ 95 96 #ifndef CONFIG_MONITOR_IS_IN_RAM 97 #define CONFIG_ENV_OFFSET 0x4000 98 #define CONFIG_ENV_SECT_SIZE 0x2000 99 #else 100 #define CONFIG_ENV_ADDR 0xffe04000 101 #define CONFIG_ENV_SECT_SIZE 0x2000 102 #endif 103 104 #define LDS_BOARD_TEXT \ 105 . = DEFINED(env_offset) ? env_offset : .; \ 106 env/embedded.o(.text); 107 108 /* 109 * BOOTP options 110 */ 111 #define CONFIG_BOOTP_BOOTFILESIZE 112 #define CONFIG_BOOTP_BOOTPATH 113 #define CONFIG_BOOTP_GATEWAY 114 #define CONFIG_BOOTP_HOSTNAME 115 116 /* 117 * Command line configuration. 118 */ 119 120 #ifdef CONFIG_MCFFEC 121 # define CONFIG_MII 1 122 # define CONFIG_MII_INIT 1 123 # define CONFIG_SYS_DISCOVER_PHY 124 # define CONFIG_SYS_RX_ETH_BUFFER 8 125 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 126 127 # define CONFIG_SYS_FEC0_PINMUX 0 128 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 129 # define MCFFEC_TOUT_LOOP 50000 130 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 131 # ifndef CONFIG_SYS_DISCOVER_PHY 132 # define FECDUPLEX FULL 133 # define FECSPEED _100BASET 134 # else 135 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 136 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 137 # endif 138 # endif /* CONFIG_SYS_DISCOVER_PHY */ 139 #endif 140 141 /* 142 *----------------------------------------------------------------------------- 143 * Define user parameters that have to be customized most likely 144 *----------------------------------------------------------------------------- 145 */ 146 147 /*AUTOBOOT settings - booting images automatically by u-boot after power on*/ 148 149 /* The following settings will be contained in the environment block ; if you 150 want to use a neutral environment all those settings can be manually set in 151 u-boot: 'set' command */ 152 153 #if 0 154 155 #define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please 156 enter a valid image address in flash */ 157 158 /* User network settings */ 159 160 #define CONFIG_IPADDR 192.168.100.2 /* default board IP address */ 161 #define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */ 162 163 #endif 164 165 #define CONFIG_SYS_LOAD_ADDR 0x20000 /*Defines default RAM address 166 from which user programs will be started */ 167 168 /*---*/ 169 170 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 171 172 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 173 174 /* 175 *----------------------------------------------------------------------------- 176 * End of user parameters to be customized 177 *----------------------------------------------------------------------------- 178 */ 179 180 /* --- 181 * Defines memory range for test 182 * --- 183 */ 184 185 #define CONFIG_SYS_MEMTEST_START 0x400 186 #define CONFIG_SYS_MEMTEST_END 0x380000 187 188 /* --- 189 * Low Level Configuration Settings 190 * (address mappings, register initial values, etc.) 191 * You should know what you are doing if you make changes here. 192 * --- 193 */ 194 195 /* --- 196 * Base register address 197 * --- 198 */ 199 200 #define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ 201 202 /* --- 203 * System Conf. Reg. & System Protection Reg. 204 * --- 205 */ 206 207 #define CONFIG_SYS_SCR 0x0003 208 #define CONFIG_SYS_SPR 0xffff 209 210 /* --- 211 * Ethernet settings 212 * --- 213 */ 214 215 #define CONFIG_SYS_DISCOVER_PHY 216 #define CONFIG_SYS_ENET_BD_BASE 0x780000 217 218 /*----------------------------------------------------------------------- 219 * Definitions for initial stack pointer and data area (in internal SRAM) 220 */ 221 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 222 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ 223 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 224 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 225 226 /*----------------------------------------------------------------------- 227 * Start addresses for the final memory configuration 228 * (Set up by the startup code) 229 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 230 */ 231 #define CONFIG_SYS_SDRAM_BASE 0x00000000 232 233 /* 234 *------------------------------------------------------------------------- 235 * RAM SIZE (is defined above) 236 *----------------------------------------------------------------------- 237 */ 238 239 /* #define CONFIG_SYS_SDRAM_SIZE 16 */ 240 241 /* 242 *----------------------------------------------------------------------- 243 */ 244 245 #define CONFIG_SYS_FLASH_BASE 0xffe00000 246 247 #ifdef CONFIG_MONITOR_IS_IN_RAM 248 #define CONFIG_SYS_MONITOR_BASE 0x20000 249 #else 250 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 251 #endif 252 253 #define CONFIG_SYS_MONITOR_LEN 0x20000 254 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 255 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 256 257 /* 258 * For booting Linux, the board info and command line data 259 * have to be in the first 8 MB of memory, since this is 260 * the maximum mapped by the Linux kernel during initialization ?? 261 */ 262 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 263 264 /*----------------------------------------------------------------------- 265 * FLASH organization 266 */ 267 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 268 #define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ 269 #define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */ 270 271 /*----------------------------------------------------------------------- 272 * Cache Configuration 273 */ 274 #define CONFIG_SYS_CACHELINE_SIZE 16 275 276 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 277 CONFIG_SYS_INIT_RAM_SIZE - 8) 278 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 279 CONFIG_SYS_INIT_RAM_SIZE - 4) 280 #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) 281 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ 282 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 283 CF_ACR_EN | CF_ACR_SM_ALL) 284 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ 285 CF_CACR_DISD | CF_CACR_INVI | \ 286 CF_CACR_CEIB | CF_CACR_DCM | \ 287 CF_CACR_EUSP) 288 289 /*----------------------------------------------------------------------- 290 * Memory bank definitions 291 * 292 * Please refer also to Motorola Coldfire user manual - Chapter XXX 293 * <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf> 294 */ 295 #define CONFIG_SYS_BR0_PRELIM 0xFFE00201 296 #define CONFIG_SYS_OR0_PRELIM 0xFFE00014 297 298 #define CONFIG_SYS_BR1_PRELIM 0 299 #define CONFIG_SYS_OR1_PRELIM 0 300 301 #define CONFIG_SYS_BR2_PRELIM 0 302 #define CONFIG_SYS_OR2_PRELIM 0 303 304 #define CONFIG_SYS_BR3_PRELIM 0 305 #define CONFIG_SYS_OR3_PRELIM 0 306 307 #define CONFIG_SYS_BR4_PRELIM 0 308 #define CONFIG_SYS_OR4_PRELIM 0 309 310 #define CONFIG_SYS_BR5_PRELIM 0 311 #define CONFIG_SYS_OR5_PRELIM 0 312 313 #define CONFIG_SYS_BR6_PRELIM 0 314 #define CONFIG_SYS_OR6_PRELIM 0 315 316 #define CONFIG_SYS_BR7_PRELIM 0x00000701 317 #define CONFIG_SYS_OR7_PRELIM 0xFF00007C 318 319 /*----------------------------------------------------------------------- 320 * LED config 321 */ 322 #define LED_STAT_0 0xffff /*all LEDs off*/ 323 #define LED_STAT_1 0xfffe 324 #define LED_STAT_2 0xfffd 325 #define LED_STAT_3 0xfffb 326 #define LED_STAT_4 0xfff7 327 #define LED_STAT_5 0xffef 328 #define LED_STAT_6 0xffdf 329 #define LED_STAT_7 0xff00 /*all LEDs on*/ 330 331 /*----------------------------------------------------------------------- 332 * Port configuration (GPIO) 333 */ 334 #define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external 335 GPIO*/ 336 #define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs 337 (1^=output, 0^=input) */ 338 #define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ 339 #define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART 340 configuration */ 341 #define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ 342 #define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */ 343 #define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */ 344 345 #endif /* _CONFIG_COBRA5272_H */ 346