1 /* 2 * bur_am335x_common.h 3 * 4 * common parts used by B&R AM335x based boards 5 * 6 * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> - 7 * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com 8 * 9 * SPDX-License-Identifier: GPL-2.0+ 10 */ 11 12 #ifndef __BUR_AM335X_COMMON_H__ 13 #define __BUR_AM335X_COMMON_H__ 14 /* ------------------------------------------------------------------------- */ 15 #define BUR_COMMON_ENV \ 16 "usbscript=usb start && fatload usb 0 0x80000000 usbscript.img && source\0" \ 17 "defaultip=192.168.60.253\0" \ 18 "defaultsip=192.168.60.254\0" \ 19 "netconsole=echo switching to network console ...; " \ 20 "if dhcp; then " \ 21 "setenv ncip ${serverip}; else " \ 22 "setenv ncip 192.168.60.254; " \ 23 "setenv serverip 192.168.60.254; " \ 24 "setenv gatewayip 192.168.60.254; " \ 25 "setenv ipaddr 192.168.60.1; " \ 26 "fi;" \ 27 "setenv netdisplay0 '" \ 28 "setcurs 1 9; puts myip; setcurs 10 9; puts ${ipaddr};" \ 29 "setcurs 1 10;puts serverip; setcurs 10 10; puts ${serverip};" \ 30 "run netdisplay0; " \ 31 "setenv stdout nc;setenv stdin nc;setenv stderr nc\0" 32 33 #define CONFIG_CMD_TIME 34 35 #define CONFIG_SYS_GENERIC_BOARD 36 37 #define CONFIG_AM33XX 38 #define CONFIG_OMAP 39 #define CONFIG_OMAP_COMMON 40 #define CONFIG_BOARD_LATE_INIT 41 #define CONFIG_SYS_CACHELINE_SIZE 64 42 #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ 43 44 /* Timer information */ 45 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 46 #define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ 47 #define CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC /* enable 32kHz OSC at bootime */ 48 #define CONFIG_SPL_POWER_SUPPORT 49 #define CONFIG_POWER_TPS65217 50 51 #define CONFIG_SYS_NO_FLASH /* have no NOR-flash */ 52 53 #include <asm/arch/omap.h> 54 55 /* NS16550 Configuration */ 56 #define CONFIG_SYS_NS16550 57 #define CONFIG_SYS_NS16550_SERIAL 58 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 59 #define CONFIG_SYS_NS16550_CLK 48000000 60 #define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */ 61 #define CONFIG_BAUDRATE 115200 62 63 /* Network defines */ 64 #define CONFIG_CMD_DHCP 65 #define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */ 66 #define CONFIG_BOOTP_SEND_HOSTNAME 67 #define CONFIG_BOOTP_GATEWAY 68 #define CONFIG_BOOTP_SUBNETMASK 69 #define CONFIG_NET_RETRY_COUNT 2 70 #define CONFIG_CMD_PING 71 #define CONFIG_DRIVER_TI_CPSW /* Driver for IP block */ 72 #define CONFIG_MII /* Required in net/eth.c */ 73 #define CONFIG_SPL_ETH_SUPPORT 74 #define CONFIG_PHYLIB 75 #define CONFIG_PHY_NATSEMI 76 #define CONFIG_SPL_NET_SUPPORT 77 #define CONFIG_SPL_ENV_SUPPORT /* used for a fetching MAC-Address */ 78 #define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL" 79 /* Network console */ 80 #define CONFIG_NETCONSOLE 1 81 #define CONFIG_BOOTP_MAY_FAIL /* if we don't have DHCP environment */ 82 /* 83 * SPL related defines. The Public RAM memory map the ROM defines the 84 * area between 0x402F0400 and 0x4030B800 as a download area and 85 * 0x4030B800 to 0x4030CE00 as a public stack area. The ROM also 86 * supports X-MODEM loading via UART, and we leverage this and then use 87 * Y-MODEM to load u-boot.img, when booted over UART. 88 */ 89 #define CONFIG_SPL_TEXT_BASE 0x402F0400 90 #define CONFIG_SPL_MAX_SIZE (0x4030B800 - CONFIG_SPL_TEXT_BASE) 91 92 /* 93 * Since SPL did pll and ddr initialization for us, 94 * we don't need to do it twice. 95 */ 96 #if !defined(CONFIG_SPL_BUILD) && !defined(CONFIG_NOR_BOOT) 97 #define CONFIG_SKIP_LOWLEVEL_INIT 98 #endif /* !CONFIG_SPL_BUILD, ... */ 99 /* 100 * Our DDR memory always starts at 0x80000000 and U-Boot shall have 101 * relocated itself to higher in memory by the time this value is used. 102 */ 103 #define CONFIG_SYS_LOAD_ADDR 0x80000000 104 /* 105 * ---------------------------------------------------------------------------- 106 * DDR information. We say (for simplicity) that we have 1 bank, 107 * always, even when we have more. We always start at 0x80000000, 108 * and we place the initial stack pointer in our SRAM. 109 */ 110 #define CONFIG_NR_DRAM_BANKS 1 111 #define CONFIG_SYS_SDRAM_BASE 0x80000000 112 #define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ 113 GENERATED_GBL_DATA_SIZE) 114 115 /* I2C */ 116 #define CONFIG_SYS_I2C 117 #define CONFIG_SYS_OMAP24_I2C_SPEED 100000 118 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 119 #define CONFIG_SYS_I2C_OMAP24XX 120 #define CONFIG_CMD_I2C 121 /* GPIO */ 122 #define CONFIG_OMAP_GPIO 123 #define CONFIG_CMD_GPIO 124 /* 125 * ---------------------------------------------------------------------------- 126 * The following are general good-enough settings for U-Boot. We set a 127 * large malloc pool as we generally have a lot of DDR, and we opt for 128 * function over binary size in the main portion of U-Boot as this is 129 * generally easily constrained later if needed. We enable the config 130 * options that give us information in the environment about what board 131 * we are on so we do not need to rely on the command prompt. We set a 132 * console baudrate of 115200 and use the default baud rate table. 133 */ 134 #define CONFIG_SYS_MALLOC_LEN (5120 << 10) 135 #define CONFIG_SYS_HUSH_PARSER 136 #define CONFIG_SYS_PROMPT "U-Boot (BuR V2.0)# " 137 #define CONFIG_SYS_CONSOLE_INFO_QUIET 138 #define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */ 139 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 140 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE 141 142 /* As stated above, the following choices are optional. */ 143 #define CONFIG_SYS_LONGHELP 144 #define CONFIG_AUTO_COMPLETE 145 #define CONFIG_CMDLINE_EDITING 146 #define CONFIG_VERSION_VARIABLE 147 148 /* We set the max number of command args high to avoid HUSH bugs. */ 149 #define CONFIG_SYS_MAXARGS 64 150 151 /* Console I/O Buffer Size */ 152 #define CONFIG_SYS_CBSIZE 512 153 /* Print Buffer Size */ 154 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE +\ 155 sizeof(CONFIG_SYS_PROMPT) + 16) 156 /* Boot Argument Buffer Size */ 157 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 158 /* 159 * For commands to use, we take the default list and add a few other 160 * useful commands. Note that we must have set CONFIG_SYS_NO_FLASH 161 * prior to this include, in order to skip a few commands. When we do 162 * have flash, if we expect these commands they must be enabled in that 163 * config. If desired, a specific list of desired commands can be used 164 * instead. 165 */ 166 #include <config_cmd_default.h> 167 /* undefine commands, which we do not need */ 168 #undef CONFIG_CMD_EDITENV 169 #undef CONFIG_CMD_FPGA 170 #undef CONFIG_CMD_IMI 171 #undef CONFIG_CMD_ITEST 172 #undef CONFIG_CMD_LOADS 173 #undef CONFIG_CMD_LOADB 174 #undef CONFIG_CMD_NFS 175 #undef CONFIG_CMD_SETGETDCR 176 #undef CONFIG_CMD_XIMG 177 /* define command we need always */ 178 #define CONFIG_CMD_ECHO 179 #define CONFIG_CMD_SOURCE 180 181 /* 182 * Our platforms make use of SPL to initalize the hardware (primarily 183 * memory) enough for full U-Boot to be loaded. We also support Falcon 184 * Mode so that the Linux kernel can be booted directly from SPL 185 * instead, if desired. We make use of the general SPL framework found 186 * under common/spl/. Given our generally common memory map, we set a 187 * number of related defaults and sizes here. 188 */ 189 #define CONFIG_SPL_FRAMEWORK 190 /* 191 * Place the image at the start of the ROM defined image space. 192 * We limit our size to the ROM-defined downloaded image area, and use the 193 * rest of the space for stack. We load U-Boot itself into memory at 194 * 0x80800000 for legacy reasons (to not conflict with older SPLs). We 195 * have our BSS be placed 1MiB after this, to allow for the default 196 * Linux kernel address of 0x80008000 to work, in the Falcon Mode case. 197 * We have the SPL malloc pool at the end of the BSS area. 198 * 199 * ---------------------------------------------------------------------------- 200 */ 201 #undef CONFIG_SYS_TEXT_BASE 202 #define CONFIG_SYS_TEXT_BASE 0x80800000 203 #define CONFIG_SPL_BSS_START_ADDR 0x80A00000 204 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ 205 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ 206 CONFIG_SPL_BSS_MAX_SIZE) 207 #define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN 208 209 /* General parts of the framework, required. */ 210 #define CONFIG_SPL_I2C_SUPPORT 211 #define CONFIG_SPL_LIBCOMMON_SUPPORT 212 #define CONFIG_SPL_LIBGENERIC_SUPPORT 213 #define CONFIG_SPL_SERIAL_SUPPORT 214 #define CONFIG_SPL_BOARD_INIT 215 #define CONFIG_SPL_YMODEM_SUPPORT 216 #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" 217 218 #endif /* ! __BUR_AM335X_COMMON_H__ */ 219