1 /* 2 * Copyright (C) 2010 Andreas Bießmann <biessmann.devel@googlemail.com> 3 * 4 * based on previous work by 5 * 6 * Ulf Samuelsson <ulf@atmel.com> 7 * Rick Bronson <rick@efn.org> 8 * 9 * Configuration settings for the AT91RM9200EK board. 10 * 11 * SPDX-License-Identifier: GPL-2.0+ 12 */ 13 14 #ifndef __AT91RM9200EK_CONFIG_H__ 15 #define __AT91RM9200EK_CONFIG_H__ 16 17 #include <linux/sizes.h> 18 19 /* 20 * set some initial configurations depending on configure target 21 * 22 * at91rm9200ek_config -> boot from 0x0 in NOR Flash at CS0 23 * at91rm9200ek_ram_config -> continue booting from 0x20100000 in RAM; lowlevel 24 * initialisation was done by some preloader 25 */ 26 #ifdef CONFIG_RAMBOOT 27 #define CONFIG_SKIP_LOWLEVEL_INIT 28 #define CONFIG_SYS_TEXT_BASE 0x20100000 29 #else 30 #define CONFIG_SYS_TEXT_BASE 0x10000000 31 #endif 32 33 /* 34 * AT91C_XTAL_CLOCK is the frequency of external xtal in hertz 35 * AT91C_MAIN_CLOCK is the frequency of PLLA output 36 * AT91C_MASTER_CLOCK is the peripherial clock 37 * CONFIG_SYS_HZ_CLOCK is the value for CCR in tc0 (divider 2 is implicitely 38 * set in arch/arm/cpu/arm920t/at91/timer.c) 39 * CONFIG_SYS_HZ is the tick rate for timer tc0 40 */ 41 #define AT91C_XTAL_CLOCK 18432000 42 #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 43 #define AT91C_MAIN_CLOCK ((AT91C_XTAL_CLOCK / 4) * 39) 44 #define AT91C_MASTER_CLOCK (AT91C_MAIN_CLOCK / 3 ) 45 #define CONFIG_SYS_HZ_CLOCK (AT91C_MASTER_CLOCK / 2) 46 47 /* CPU configuration */ 48 #define CONFIG_AT91RM9200 49 #define CONFIG_AT91RM9200EK 50 #define CONFIG_CPUAT91 51 #define USE_920T_MMU 52 53 #include <asm/hardware.h> /* needed for port definitions */ 54 55 #define CONFIG_CMDLINE_TAG 56 #define CONFIG_SETUP_MEMORY_TAGS 57 #define CONFIG_INITRD_TAG 58 59 #define CONFIG_BOARD_EARLY_INIT_F 60 61 #define CONFIG_CMD_BOOTZ 62 63 /* 64 * Memory Configuration 65 */ 66 #define CONFIG_NR_DRAM_BANKS 1 67 #define CONFIG_SYS_SDRAM_BASE 0x20000000 68 #define CONFIG_SYS_SDRAM_SIZE SZ_32M 69 70 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 71 #define CONFIG_SYS_MEMTEST_END \ 72 (CONFIG_SYS_MEMTEST_START + CONFIG_SYS_SDRAM_SIZE - SZ_256K) 73 74 /* 75 * LowLevel Init 76 */ 77 #ifndef CONFIG_SKIP_LOWLEVEL_INIT 78 #define CONFIG_SYS_USE_MAIN_OSCILLATOR 79 /* flash */ 80 #define CONFIG_SYS_EBI_CFGR_VAL 0x00000000 81 #define CONFIG_SYS_SMC_CSR0_VAL 0x00003284 /* 16bit, 2 TDF, 4 WS */ 82 83 /* clocks */ 84 #define CONFIG_SYS_PLLAR_VAL 0x20263E04 /* 179.712000 MHz for PCK */ 85 #define CONFIG_SYS_PLLBR_VAL 0x10483E0E /* 48.054857 MHz (divider by 2 for USB) */ 86 /* PCK/3 = MCK Master Clock = 59.904000MHz from PLLA */ 87 #define CONFIG_SYS_MCKR_VAL 0x00000202 88 89 /* sdram */ 90 #define CONFIG_SYS_PIOC_ASR_VAL 0xFFFF0000 /* Configure PIOC as peripheral (D16/D31) */ 91 #define CONFIG_SYS_PIOC_BSR_VAL 0x00000000 92 #define CONFIG_SYS_PIOC_PDR_VAL 0xFFFF0000 93 #define CONFIG_SYS_EBI_CSA_VAL 0x00000002 /* CS1=CONFIG_SYS_SDRAM */ 94 #define CONFIG_SYS_SDRC_CR_VAL 0x2188c155 /* set up the CONFIG_SYS_SDRAM */ 95 #define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE /* address of the SDRAM */ 96 #define CONFIG_SYS_SDRAM1 (CONFIG_SYS_SDRAM_BASE+0x80) 97 #define CONFIG_SYS_SDRAM_VAL 0x00000000 /* value written to CONFIG_SYS_SDRAM */ 98 #define CONFIG_SYS_SDRC_MR_VAL 0x00000002 /* Precharge All */ 99 #define CONFIG_SYS_SDRC_MR_VAL1 0x00000004 /* refresh */ 100 #define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */ 101 #define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */ 102 #define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */ 103 #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ 104 105 /* 106 * Hardware drivers 107 */ 108 /* 109 * Choose a USART for serial console 110 * CONFIG_DBGU is DBGU unit on J10 111 * CONFIG_USART1 is USART1 on J14 112 */ 113 #define CONFIG_ATMEL_USART 114 #define CONFIG_USART_BASE ATMEL_BASE_DBGU 115 #define CONFIG_USART_ID 0/* ignored in arm */ 116 117 #define CONFIG_BAUDRATE 115200 118 119 /* 120 * Command line configuration. 121 */ 122 #define CONFIG_CMD_FAT 123 #define CONFIG_CMD_MII 124 125 /* 126 * Network Driver Setting 127 */ 128 #define CONFIG_DRIVER_AT91EMAC 129 #define CONFIG_SYS_RX_ETH_BUFFER 16 130 #define CONFIG_RMII 131 #define CONFIG_MII 132 133 /* 134 * NOR Flash 135 */ 136 #define CONFIG_FLASH_CFI_DRIVER 137 #define CONFIG_SYS_FLASH_CFI 138 #define CONFIG_SYS_FLASH_BASE 0x10000000 139 #define PHYS_FLASH_1 CONFIG_SYS_FLASH_BASE 140 #define PHYS_FLASH_SIZE SZ_8M 141 #define CONFIG_SYS_MAX_FLASH_BANKS 1 142 #define CONFIG_SYS_MAX_FLASH_SECT 256 143 #define CONFIG_SYS_FLASH_PROTECTION 144 145 /* 146 * USB Config 147 */ 148 #define CONFIG_USB_ATMEL 1 149 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB 150 #define CONFIG_USB_OHCI_NEW 1 151 #define CONFIG_USB_KEYBOARD 1 152 #define CONFIG_USB_STORAGE 1 153 #define CONFIG_DOS_PARTITION 1 154 155 #define CONFIG_SYS_USB_OHCI_CPU_INIT 1 156 #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_USB_HOST_BASE 157 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91rm9200" 158 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 159 160 /* 161 * Environment Settings 162 */ 163 #define CONFIG_ENV_IS_IN_FLASH 164 165 /* 166 * after u-boot.bin 167 */ 168 #define CONFIG_ENV_ADDR \ 169 (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) 170 #define CONFIG_ENV_SIZE SZ_64K /* sectors are 64K here */ 171 /* The following #defines are needed to get flash environment right */ 172 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 173 #define CONFIG_SYS_MONITOR_LEN SZ_256K 174 175 /* 176 * Boot option 177 */ 178 #define CONFIG_BOOTDELAY 3 179 180 /* default load address */ 181 #define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + SZ_16M 182 #define CONFIG_ENV_OVERWRITE 183 184 /* 185 * Shell Settings 186 */ 187 #define CONFIG_CMDLINE_EDITING 188 #define CONFIG_SYS_LONGHELP 189 #define CONFIG_AUTO_COMPLETE 190 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 191 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 192 /* Print Buffer Size */ 193 #define CONFIG_SYS_PBSIZE \ 194 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 195 196 /* 197 * Size of malloc() pool 198 */ 199 #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + SZ_128K, \ 200 SZ_4K) 201 202 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_4K \ 203 - GENERATED_GBL_DATA_SIZE) 204 205 #endif /* __AT91RM9200EK_CONFIG_H__ */ 206