1 /* 2 * Copyright (C) 2016 Timesys Corporation 3 * Copyright (C) 2016 Advantech Corporation 4 * Copyright (C) 2012 Freescale Semiconductor, Inc. 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __ADVANTECH_DMSBA16_CONFIG_H 10 #define __ADVANTECH_DMSBA16_CONFIG_H 11 12 #include <asm/arch/imx-regs.h> 13 #include <asm/imx-common/gpio.h> 14 15 #define CONFIG_BOARD_NAME "Advantech DMS-BA16" 16 #define CONFIG_DEFAULT_FDT_FILE "imx6q-dms-ba16.dtb" 17 18 #define CONFIG_MXC_UART_BASE UART4_BASE 19 #define CONFIG_CONSOLE_DEV "ttymxc3" 20 #define CONFIG_EXTRA_BOOTARGS "panic=10" 21 22 #define CONFIG_BOOT_DIR "" 23 #define CONFIG_LOADCMD "fatload" 24 #define CONFIG_RFSPART "2" 25 26 #define CONFIG_SUPPORT_EMMC_BOOT 27 28 #include "mx6_common.h" 29 #include <linux/sizes.h> 30 31 #define CONFIG_DISPLAY_BOARDINFO 32 33 #define CONFIG_CMDLINE_TAG 34 #define CONFIG_SETUP_MEMORY_TAGS 35 #define CONFIG_INITRD_TAG 36 #define CONFIG_REVISION_TAG 37 #define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) 38 39 #define CONFIG_BOARD_EARLY_INIT_F 40 #define CONFIG_BOARD_LATE_INIT 41 42 #define CONFIG_MXC_GPIO 43 #define CONFIG_MXC_UART 44 45 #define CONFIG_CMD_FUSE 46 #define CONFIG_MXC_OCOTP 47 48 /* SATA Configs */ 49 #define CONFIG_CMD_SATA 50 #define CONFIG_DWC_AHSATA 51 #define CONFIG_SYS_SATA_MAX_DEVICE 1 52 #define CONFIG_DWC_AHSATA_PORT_ID 0 53 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR 54 #define CONFIG_LBA48 55 #define CONFIG_LIBATA 56 57 /* MMC Configs */ 58 #define CONFIG_FSL_ESDHC 59 #define CONFIG_FSL_USDHC 60 #define CONFIG_SYS_FSL_ESDHC_ADDR 0 61 #define CONFIG_MMC 62 #define CONFIG_GENERIC_MMC 63 #define CONFIG_BOUNCE_BUFFER 64 #define CONFIG_DOS_PARTITION 65 66 /* USB Configs */ 67 #define CONFIG_USB_EHCI 68 #define CONFIG_USB_EHCI_MX6 69 #define CONFIG_USB_STORAGE 70 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 71 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 72 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 73 #define CONFIG_MXC_USB_FLAGS 0 74 #define CONFIG_USB_KEYBOARD 75 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP 76 77 #define CONFIG_USBD_HS 78 #define CONFIG_USB_FUNCTION_MASS_STORAGE 79 #define CONFIG_USB_GADGET_VBUS_DRAW 2 80 81 /* Networking Configs */ 82 #define CONFIG_FEC_MXC 83 #define CONFIG_MII 84 #define IMX_FEC_BASE ENET_BASE_ADDR 85 #define CONFIG_FEC_XCV_TYPE RGMII 86 #define CONFIG_ETHPRIME "FEC" 87 #define CONFIG_FEC_MXC_PHYADDR 4 88 #define CONFIG_PHYLIB 89 #define CONFIG_PHY_ATHEROS 90 91 /* Serial Flash */ 92 #ifdef CONFIG_CMD_SF 93 #define CONFIG_MXC_SPI 94 #define CONFIG_SF_DEFAULT_BUS 0 95 #define CONFIG_SF_DEFAULT_CS 0 96 #define CONFIG_SF_DEFAULT_SPEED 20000000 97 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 98 #endif 99 100 /* allow to overwrite serial and ethaddr */ 101 #define CONFIG_ENV_OVERWRITE 102 #define CONFIG_CONS_INDEX 1 103 #define CONFIG_BAUDRATE 115200 104 105 /* Command definition */ 106 #define CONFIG_CMD_BMODE 107 108 #define CONFIG_LOADADDR 0x12000000 109 #define CONFIG_SYS_TEXT_BASE 0x17800000 110 111 #define CONFIG_EXTRA_ENV_SETTINGS \ 112 "script=boot.scr\0" \ 113 "image=" CONFIG_BOOT_DIR "/uImage\0" \ 114 "uboot=u-boot.imx\0" \ 115 "fdt_file=" CONFIG_BOOT_DIR "/" CONFIG_DEFAULT_FDT_FILE "\0" \ 116 "fdt_addr=0x18000000\0" \ 117 "boot_fdt=yes\0" \ 118 "ip_dyn=yes\0" \ 119 "console=" CONFIG_CONSOLE_DEV "\0" \ 120 "fdt_high=0xffffffff\0" \ 121 "initrd_high=0xffffffff\0" \ 122 "sddev=0\0" \ 123 "emmcdev=1\0" \ 124 "partnum=1\0" \ 125 "loadcmd=" CONFIG_LOADCMD "\0" \ 126 "rfspart=" CONFIG_RFSPART "\0" \ 127 "update_sd_firmware=" \ 128 "if test ${ip_dyn} = yes; then " \ 129 "setenv get_cmd dhcp; " \ 130 "else " \ 131 "setenv get_cmd tftp; " \ 132 "fi; " \ 133 "if mmc dev ${mmcdev}; then " \ 134 "if ${get_cmd} ${update_sd_firmware_filename}; then " \ 135 "setexpr fw_sz ${filesize} / 0x200; " \ 136 "setexpr fw_sz ${fw_sz} + 1; " \ 137 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \ 138 "fi; " \ 139 "fi\0" \ 140 "update_sf_uboot=" \ 141 "if tftp $loadaddr $uboot; then " \ 142 "sf probe; " \ 143 "sf erase 0 0xC0000; " \ 144 "sf write $loadaddr 0x400 $filesize; " \ 145 "echo 'U-Boot upgraded. Please reset'; " \ 146 "fi\0" \ 147 "setargs=setenv bootargs console=${console},${baudrate} " \ 148 "root=/dev/${rootdev} rw rootwait " CONFIG_EXTRA_BOOTARGS "\0" \ 149 "loadbootscript=" \ 150 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \ 151 "bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \ 152 " source\0" \ 153 "loadimage=" \ 154 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \ 155 "loadfdt=${loadcmd} ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \ 156 "tryboot=" \ 157 "if run loadbootscript; then " \ 158 "run bootscript; " \ 159 "else " \ 160 "if run loadimage; then " \ 161 "run doboot; " \ 162 "fi; " \ 163 "fi;\0" \ 164 "doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \ 165 "run setargs; " \ 166 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ 167 "if run loadfdt; then " \ 168 "bootm ${loadaddr} - ${fdt_addr}; " \ 169 "else " \ 170 "if test ${boot_fdt} = try; then " \ 171 "bootm; " \ 172 "else " \ 173 "echo WARN: Cannot load the DT; " \ 174 "fi; " \ 175 "fi; " \ 176 "else " \ 177 "bootm; " \ 178 "fi;\0" \ 179 "netargs=setenv bootargs console=${console},${baudrate} " \ 180 "root=/dev/nfs " \ 181 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ 182 "netboot=echo Booting from net ...; " \ 183 "run netargs; " \ 184 "if test ${ip_dyn} = yes; then " \ 185 "setenv get_cmd dhcp; " \ 186 "else " \ 187 "setenv get_cmd tftp; " \ 188 "fi; " \ 189 "${get_cmd} ${image}; " \ 190 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ 191 "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ 192 "bootm ${loadaddr} - ${fdt_addr}; " \ 193 "else " \ 194 "if test ${boot_fdt} = try; then " \ 195 "bootm; " \ 196 "else " \ 197 "echo WARN: Cannot load the DT; " \ 198 "fi; " \ 199 "fi; " \ 200 "else " \ 201 "bootm; " \ 202 "fi;\0" \ 203 204 #define CONFIG_BOOTCOMMAND \ 205 "usb start; " \ 206 "setenv dev usb; " \ 207 "setenv devnum 0; " \ 208 "setenv rootdev sda${rfspart}; " \ 209 "run tryboot; " \ 210 \ 211 "setenv dev mmc; " \ 212 "setenv rootdev mmcblk0p${rfspart}; " \ 213 \ 214 "setenv devnum ${sddev}; " \ 215 "if mmc dev ${devnum}; then " \ 216 "run tryboot; " \ 217 "fi; " \ 218 \ 219 "setenv devnum ${emmcdev}; " \ 220 "setenv rootdev mmcblk${emmcdev}p${rfspart}; " \ 221 "if mmc dev ${devnum}; then " \ 222 "run tryboot; " \ 223 "fi; " \ 224 \ 225 "bmode usb; " \ 226 227 #define CONFIG_ARP_TIMEOUT 200UL 228 229 /* Miscellaneous configurable options */ 230 #define CONFIG_SYS_LONGHELP 231 #define CONFIG_AUTO_COMPLETE 232 233 /* Print Buffer Size */ 234 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 235 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 236 237 #define CONFIG_SYS_MEMTEST_START 0x10000000 238 #define CONFIG_SYS_MEMTEST_END 0x10010000 239 #define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000 240 241 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR 242 243 #define CONFIG_CMDLINE_EDITING 244 #define CONFIG_STACKSIZE (128 * 1024) 245 246 /* Physical Memory Map */ 247 #define CONFIG_NR_DRAM_BANKS 1 248 #define PHYS_SDRAM MMDC0_ARB_BASE_ADDR 249 250 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM 251 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR 252 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE 253 254 #define CONFIG_SYS_INIT_SP_OFFSET \ 255 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 256 #define CONFIG_SYS_INIT_SP_ADDR \ 257 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 258 259 /* FLASH and environment organization */ 260 #define CONFIG_SYS_NO_FLASH 261 262 #define CONFIG_ENV_IS_IN_SPI_FLASH 263 #define CONFIG_ENV_SIZE (8 * 1024) 264 #define CONFIG_ENV_OFFSET (768 * 1024) 265 #define CONFIG_ENV_SECT_SIZE (64 * 1024) 266 #define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS 267 #define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS 268 #define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE 269 #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED 270 271 #ifndef CONFIG_SYS_DCACHE_OFF 272 #endif 273 274 #define CONFIG_SYS_FSL_USDHC_NUM 3 275 276 /* Framebuffer */ 277 #define CONFIG_VIDEO 278 #define CONFIG_VIDEO_IPUV3 279 #define CONFIG_CFB_CONSOLE 280 #define CONFIG_VGA_AS_SINGLE_DEVICE 281 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 282 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE 283 #define CONFIG_VIDEO_BMP_RLE8 284 #define CONFIG_SPLASH_SCREEN 285 #define CONFIG_SPLASH_SCREEN_ALIGN 286 #define CONFIG_BMP_16BPP 287 #define CONFIG_VIDEO_LOGO 288 #define CONFIG_VIDEO_BMP_LOGO 289 #define CONFIG_IPUV3_CLK 260000000 290 #define CONFIG_IMX_HDMI 291 #define CONFIG_IMX_VIDEO_SKIP 292 293 #define CONFIG_PWM_IMX 294 #define CONFIG_IMX6_PWM_PER_CLK 66000000 295 296 #undef CONFIG_CMD_PCI 297 #ifdef CONFIG_CMD_PCI 298 #define CONFIG_PCI 299 #define CONFIG_PCI_PNP 300 #define CONFIG_PCI_SCAN_SHOW 301 #define CONFIG_PCIE_IMX 302 #define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12) 303 #define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5) 304 #endif 305 306 /* I2C Configs */ 307 #define CONFIG_SYS_I2C 308 #define CONFIG_SYS_I2C_MXC 309 #define CONFIG_SYS_I2C_SPEED 100000 310 #define CONFIG_SYS_I2C_MXC_I2C1 311 #define CONFIG_SYS_I2C_MXC_I2C2 312 #define CONFIG_SYS_I2C_MXC_I2C3 313 314 #endif /* __ADVANTECH_DMSBA16_CONFIG_H */ 315