1 /* 2 * Copyright 2013-2015 Arcturus Networks, Inc. 3 * http://www.arcturusnetworks.com/products/ucp1020/ 4 * based on include/configs/p1_p2_rdb_pc.h 5 * original copyright follows: 6 * Copyright 2009-2011 Freescale Semiconductor, Inc. 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 /* 12 * QorIQ uCP1020-xx boards configuration file 13 */ 14 #ifndef __CONFIG_H 15 #define __CONFIG_H 16 17 #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */ 18 #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */ 19 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 20 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ 21 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 22 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 23 24 #if defined(CONFIG_TARTGET_UCP1020T1) 25 26 #define CONFIG_UCP1020_REV_1_3 27 28 #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1" 29 30 #define CONFIG_TSEC_ENET 31 #define CONFIG_TSEC1 32 #define CONFIG_TSEC3 33 #define CONFIG_HAS_ETH0 34 #define CONFIG_HAS_ETH1 35 #define CONFIG_ETHADDR 00:19:D3:FF:FF:FF 36 #define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE 37 #define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD 38 #define CONFIG_IPADDR 10.80.41.229 39 #define CONFIG_SERVERIP 10.80.41.227 40 #define CONFIG_NETMASK 255.255.252.0 41 #define CONFIG_ETHPRIME "eTSEC3" 42 43 #ifndef CONFIG_SPI_FLASH 44 #endif 45 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT 46 47 #define CONFIG_SYS_L2_SIZE (256 << 10) 48 49 #define CONFIG_LAST_STAGE_INIT 50 51 #endif 52 53 #if defined(CONFIG_TARGET_UCP1020) 54 55 #define CONFIG_UCP1020 56 #define CONFIG_UCP1020_REV_1_3 57 58 #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR" 59 60 #define CONFIG_TSEC_ENET 61 #define CONFIG_TSEC1 62 #define CONFIG_TSEC2 63 #define CONFIG_TSEC3 64 #define CONFIG_HAS_ETH0 65 #define CONFIG_HAS_ETH1 66 #define CONFIG_HAS_ETH2 67 #define CONFIG_ETHADDR 00:06:3B:FF:FF:FF 68 #define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE 69 #define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD 70 #define CONFIG_IPADDR 192.168.1.81 71 #define CONFIG_IPADDR1 192.168.1.82 72 #define CONFIG_IPADDR2 192.168.1.83 73 #define CONFIG_SERVERIP 192.168.1.80 74 #define CONFIG_GATEWAYIP 102.168.1.1 75 #define CONFIG_NETMASK 255.255.255.0 76 #define CONFIG_ETHPRIME "eTSEC1" 77 78 #ifndef CONFIG_SPI_FLASH 79 #endif 80 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT 81 82 #define CONFIG_SYS_L2_SIZE (256 << 10) 83 84 #define CONFIG_LAST_STAGE_INIT 85 86 #endif 87 88 #ifdef CONFIG_SDCARD 89 #define CONFIG_RAMBOOT_SDCARD 90 #define CONFIG_SYS_RAMBOOT 91 #define CONFIG_SYS_EXTRA_ENV_RELOC 92 #define CONFIG_SYS_TEXT_BASE 0x11000000 93 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc 94 #endif 95 96 #ifdef CONFIG_SPIFLASH 97 #define CONFIG_RAMBOOT_SPIFLASH 98 #define CONFIG_SYS_RAMBOOT 99 #define CONFIG_SYS_EXTRA_ENV_RELOC 100 #define CONFIG_SYS_TEXT_BASE 0x11000000 101 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc 102 #endif 103 104 #ifndef CONFIG_SYS_TEXT_BASE 105 #define CONFIG_SYS_TEXT_BASE 0xeff80000 106 #endif 107 #define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000 108 109 #ifndef CONFIG_RESET_VECTOR_ADDRESS 110 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 111 #endif 112 113 #ifndef CONFIG_SYS_MONITOR_BASE 114 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 115 #endif 116 117 #define CONFIG_MP 118 119 #define CONFIG_ENV_OVERWRITE 120 121 #define CONFIG_CMD_SATA 122 #define CONFIG_SATA_SIL 123 #define CONFIG_SYS_SATA_MAX_DEVICE 2 124 #define CONFIG_LIBATA 125 #define CONFIG_LBA48 126 127 #define CONFIG_SYS_CLK_FREQ 66666666 128 #define CONFIG_DDR_CLK_FREQ 66666666 129 130 #define CONFIG_HWCONFIG 131 132 #define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */ 133 #define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */ 134 #define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */ 135 /* 136 * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details). 137 * there will be one entry in this array for each two (dummy) sensors in 138 * CONFIG_DTT_SENSORS. 139 * 140 * For uCP1020 module: 141 * - only one ADM1021/NCT72 142 * - i2c addr 0x41 143 * - conversion rate 0x02 = 0.25 conversions/second 144 * - ALERT output disabled 145 * - local temp sensor enabled, min set to 0 deg, max set to 85 deg 146 * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg 147 */ 148 #define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \ 149 0x02, 0, 1, 0, 85, 1, 0, 85} } 150 151 #define CONFIG_CMD_DTT 152 153 /* 154 * These can be toggled for performance analysis, otherwise use default. 155 */ 156 #define CONFIG_L2_CACHE 157 #define CONFIG_BTB 158 159 #define CONFIG_ENABLE_36BIT_PHYS 160 161 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 162 #define CONFIG_SYS_MEMTEST_END 0x1fffffff 163 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 164 165 #define CONFIG_SYS_CCSRBAR 0xffe00000 166 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 167 168 /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k 169 SPL code*/ 170 #ifdef CONFIG_SPL_BUILD 171 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 172 #endif 173 174 /* DDR Setup */ 175 #define CONFIG_DDR_ECC_ENABLE 176 #ifndef CONFIG_DDR_ECC_ENABLE 177 #define CONFIG_SYS_DDR_RAW_TIMING 178 #define CONFIG_DDR_SPD 179 #endif 180 #define CONFIG_SYS_SPD_BUS_NUM 1 181 #undef CONFIG_FSL_DDR_INTERACTIVE 182 183 #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M 184 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 185 #define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) 186 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 187 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 188 189 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 190 191 /* Default settings for DDR3 */ 192 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f 193 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 194 #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 195 #define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f 196 #define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302 197 #define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 198 199 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 200 #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 201 #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 202 #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 203 204 #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 205 #define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608 206 #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 207 #define CONFIG_SYS_DDR_RCW_1 0x00000000 208 #define CONFIG_SYS_DDR_RCW_2 0x00000000 209 #ifdef CONFIG_DDR_ECC_ENABLE 210 #define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */ 211 #else 212 #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ 213 #endif 214 #define CONFIG_SYS_DDR_CONTROL_2 0x04401050 215 #define CONFIG_SYS_DDR_TIMING_4 0x00220001 216 #define CONFIG_SYS_DDR_TIMING_5 0x03402400 217 218 #define CONFIG_SYS_DDR_TIMING_3 0x00020000 219 #define CONFIG_SYS_DDR_TIMING_0 0x00330004 220 #define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846 221 #define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF 222 #define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 223 #define CONFIG_SYS_DDR_MODE_1 0x40461520 224 #define CONFIG_SYS_DDR_MODE_2 0x8000c000 225 #define CONFIG_SYS_DDR_INTERVAL 0x0C300000 226 227 #undef CONFIG_CLOCKS_IN_MHZ 228 229 /* 230 * Memory map 231 * 232 * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable 233 * 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2) 234 * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1 235 * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable 236 * (early boot only) 237 * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable 238 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable 239 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable 240 */ 241 242 /* 243 * Local Bus Definitions 244 */ 245 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ 246 #define CONFIG_SYS_FLASH_BASE 0xec000000 247 248 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 249 250 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 251 | BR_PS_16 | BR_V) 252 253 #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 254 255 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} 256 #define CONFIG_SYS_FLASH_QUIET_TEST 257 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 258 259 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 260 261 #undef CONFIG_SYS_FLASH_CHECKSUM 262 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 263 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 264 265 #define CONFIG_FLASH_CFI_DRIVER 266 #define CONFIG_SYS_FLASH_CFI 267 #define CONFIG_SYS_FLASH_EMPTY_INFO 268 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 269 270 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 271 272 #define CONFIG_SYS_INIT_RAM_LOCK 273 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ 274 /* Initial L1 address */ 275 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR 276 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 277 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 278 /* Size of used area in RAM */ 279 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 280 281 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 282 GENERATED_GBL_DATA_SIZE) 283 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 284 285 #define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */ 286 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */ 287 288 #define CONFIG_SYS_PMC_BASE 0xff980000 289 #define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE 290 #define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \ 291 BR_PS_8 | BR_V) 292 #define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ 293 OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \ 294 OR_GPCM_EAD) 295 296 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 297 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 298 #ifdef CONFIG_NAND_FSL_ELBC 299 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */ 300 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 301 #endif 302 303 /* Serial Port - controlled on board with jumper J8 304 * open - index 2 305 * shorted - index 1 306 */ 307 #define CONFIG_CONS_INDEX 1 308 #undef CONFIG_SERIAL_SOFTWARE_FIFO 309 #define CONFIG_SYS_NS16550_SERIAL 310 #define CONFIG_SYS_NS16550_REG_SIZE 1 311 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 312 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL) 313 #define CONFIG_NS16550_MIN_FUNCTIONS 314 #endif 315 316 #define CONFIG_SYS_BAUDRATE_TABLE \ 317 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 318 319 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) 320 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) 321 322 /* I2C */ 323 #define CONFIG_SYS_I2C 324 #define CONFIG_SYS_I2C_FSL 325 #define CONFIG_SYS_FSL_I2C_SPEED 400000 326 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 327 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 328 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 329 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 330 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 331 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } 332 #define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */ 333 334 #define CONFIG_RTC_DS1337 335 #define CONFIG_SYS_RTC_DS1337_NOOSC 336 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 337 #define CONFIG_SYS_I2C_PCA9557_ADDR 0x18 338 #define CONFIG_SYS_I2C_NCT72_ADDR 0x4C 339 #define CONFIG_SYS_I2C_IDT6V49205B 0x69 340 341 /* 342 * eSPI - Enhanced SPI 343 */ 344 #define CONFIG_HARD_SPI 345 346 #define CONFIG_SF_DEFAULT_SPEED 10000000 347 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 348 349 #if defined(CONFIG_PCI) 350 /* 351 * General PCI 352 * Memory space is mapped 1-1, but I/O space must start from 0. 353 */ 354 355 /* controller 2, direct to uli, tgtid 2, Base address 9000 */ 356 #define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9" 357 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 358 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 359 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 360 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 361 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 362 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 363 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 364 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 365 366 /* controller 1, Slot 2, tgtid 1, Base address a000 */ 367 #define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10" 368 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 369 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 370 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 371 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 372 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 373 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 374 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 375 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 376 377 #define CONFIG_CMD_PCI 378 379 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 380 #define CONFIG_DOS_PARTITION 381 #endif /* CONFIG_PCI */ 382 383 /* 384 * Environment 385 */ 386 #ifdef CONFIG_ENV_FIT_UCBOOT 387 388 #define CONFIG_ENV_IS_IN_FLASH 389 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000) 390 #define CONFIG_ENV_SIZE 0x20000 391 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 392 393 #else 394 395 #define CONFIG_ENV_SPI_BUS 0 396 #define CONFIG_ENV_SPI_CS 0 397 #define CONFIG_ENV_SPI_MAX_HZ 10000000 398 #define CONFIG_ENV_SPI_MODE 0 399 400 #ifdef CONFIG_RAMBOOT_SPIFLASH 401 402 #define CONFIG_ENV_IS_IN_SPI_FLASH 403 #define CONFIG_ENV_SIZE 0x3000 /* 12KB */ 404 #define CONFIG_ENV_OFFSET 0x2000 /* 8KB */ 405 #define CONFIG_ENV_SECT_SIZE 0x1000 406 407 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) 408 /* Address and size of Redundant Environment Sector */ 409 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) 410 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 411 #endif 412 413 #elif defined(CONFIG_RAMBOOT_SDCARD) 414 #define CONFIG_ENV_IS_IN_MMC 415 #define CONFIG_FSL_FIXED_MMC_LOCATION 416 #define CONFIG_ENV_SIZE 0x2000 417 #define CONFIG_SYS_MMC_ENV_DEV 0 418 419 #elif defined(CONFIG_SYS_RAMBOOT) 420 #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ 421 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 422 #define CONFIG_ENV_SIZE 0x2000 423 424 #else 425 #define CONFIG_ENV_IS_IN_FLASH 426 #define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE) 427 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 428 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE 429 #define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000) 430 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) 431 /* Address and size of Redundant Environment Sector */ 432 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) 433 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 434 #endif 435 436 #endif 437 438 #endif /* CONFIG_ENV_FIT_UCBOOT */ 439 440 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 441 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 442 443 /* 444 * Command line configuration. 445 */ 446 #define CONFIG_CMD_IRQ 447 #define CONFIG_CMD_DATE 448 #define CONFIG_CMD_IRQ 449 #define CONFIG_CMD_REGINFO 450 #define CONFIG_CMD_ERRATA 451 #define CONFIG_CMD_CRAMFS 452 453 /* 454 * USB 455 */ 456 #define CONFIG_HAS_FSL_DR_USB 457 458 #if defined(CONFIG_HAS_FSL_DR_USB) 459 #define CONFIG_USB_EHCI 460 461 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 462 463 #ifdef CONFIG_USB_EHCI 464 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 465 #define CONFIG_USB_EHCI_FSL 466 #endif 467 #endif 468 469 #undef CONFIG_WATCHDOG /* watchdog disabled */ 470 471 #ifdef CONFIG_MMC 472 #define CONFIG_FSL_ESDHC 473 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 474 #define CONFIG_MMC_SPI 475 #define CONFIG_CMD_MMC_SPI 476 #define CONFIG_GENERIC_MMC 477 #endif 478 479 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA) 480 #define CONFIG_DOS_PARTITION 481 #endif 482 483 /* Misc Extra Settings */ 484 #undef CONFIG_WATCHDOG /* watchdog disabled */ 485 486 /* 487 * Miscellaneous configurable options 488 */ 489 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 490 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 491 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 492 #if defined(CONFIG_CMD_KGDB) 493 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 494 #else 495 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 496 #endif 497 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 498 /* Print Buffer Size */ 499 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 500 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 501 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */ 502 503 /* 504 * For booting Linux, the board info and command line data 505 * have to be in the first 64 MB of memory, since this is 506 * the maximum mapped by the Linux kernel during initialization. 507 */ 508 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ 509 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 510 511 #if defined(CONFIG_CMD_KGDB) 512 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 513 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 514 #endif 515 516 /* 517 * Environment Configuration 518 */ 519 520 #if defined(CONFIG_TSEC_ENET) 521 522 #if defined(CONFIG_UCP1020_REV_1_2) 523 #define CONFIG_PHY_MICREL_KSZ9021 524 #elif defined(CONFIG_UCP1020_REV_1_3) 525 #define CONFIG_PHY_MICREL_KSZ9031 526 #else 527 #error "UCP1020 module revision is not defined !!!" 528 #endif 529 530 #define CONFIG_BOOTP_SERVERIP 531 532 #define CONFIG_MII /* MII PHY management */ 533 #define CONFIG_TSEC1_NAME "eTSEC1" 534 #define CONFIG_TSEC2_NAME "eTSEC2" 535 #define CONFIG_TSEC3_NAME "eTSEC3" 536 537 #define TSEC1_PHY_ADDR 4 538 #define TSEC2_PHY_ADDR 0 539 #define TSEC2_PHY_ADDR_SGMII 0x00 540 #define TSEC3_PHY_ADDR 6 541 542 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 543 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 544 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 545 546 #define TSEC1_PHYIDX 0 547 #define TSEC2_PHYIDX 0 548 #define TSEC3_PHYIDX 0 549 550 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 551 552 #endif 553 554 #define CONFIG_HOSTNAME UCP1020 555 #define CONFIG_ROOTPATH "/opt/nfsroot" 556 #define CONFIG_BOOTFILE "uImage" 557 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 558 559 /* default location for tftp and bootm */ 560 #define CONFIG_LOADADDR 1000000 561 562 #define CONFIG_BOOTARGS /* the boot command will set bootargs */ 563 564 #define CONFIG_BAUDRATE 115200 565 566 #if defined(CONFIG_DONGLE) 567 568 #define CONFIG_EXTRA_ENV_SETTINGS \ 569 "bootcmd=run prog_spi_mbrbootcramfs\0" \ 570 "bootfile=uImage\0" \ 571 "consoledev=ttyS0\0" \ 572 "cramfsfile=image.cramfs\0" \ 573 "dtbaddr=0x00c00000\0" \ 574 "dtbfile=image.dtb\0" \ 575 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ 576 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ 577 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ 578 "fileaddr=0x01000000\0" \ 579 "filesize=0x00080000\0" \ 580 "flashmbr=sf probe 0; " \ 581 "tftp $loadaddr $mbr; " \ 582 "sf erase $mbr_offset +$filesize; " \ 583 "sf write $loadaddr $mbr_offset $filesize\0" \ 584 "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ 585 "protect off $nor_recoveryaddr +$filesize; " \ 586 "erase $nor_recoveryaddr +$filesize; " \ 587 "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ 588 "protect on $nor_recoveryaddr +$filesize\0 " \ 589 "flashuboot=tftp $ubootaddr $ubootfile; " \ 590 "protect off $nor_ubootaddr +$filesize; " \ 591 "erase $nor_ubootaddr +$filesize; " \ 592 "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ 593 "protect on $nor_ubootaddr +$filesize\0 " \ 594 "flashworking=tftp $workingaddr $cramfsfile; " \ 595 "protect off $nor_workingaddr +$filesize; " \ 596 "erase $nor_workingaddr +$filesize; " \ 597 "cp.b $workingaddr $nor_workingaddr $filesize; " \ 598 "protect on $nor_workingaddr +$filesize\0 " \ 599 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ 600 "kerneladdr=0x01100000\0" \ 601 "kernelfile=uImage\0" \ 602 "loadaddr=0x01000000\0" \ 603 "mbr=uCP1020d.mbr\0" \ 604 "mbr_offset=0x00000000\0" \ 605 "mmbr=uCP1020Quiet.mbr\0" \ 606 "mmcpart=0:2\0" \ 607 "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ 608 "mmc erase 1 1; " \ 609 "mmc write $loadaddr 1 1\0" \ 610 "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \ 611 "mmc erase 0x40 0x400; " \ 612 "mmc write $loadaddr 0x40 0x400\0" \ 613 "netdev=eth0\0" \ 614 "nor_recoveryaddr=0xEC0A0000\0" \ 615 "nor_ubootaddr=0xEFF80000\0" \ 616 "nor_workingaddr=0xECFA0000\0" \ 617 "norbootrecovery=setenv bootargs $recoverybootargs" \ 618 " console=$consoledev,$baudrate $othbootargs; " \ 619 "run norloadrecovery; " \ 620 "bootm $kerneladdr - $dtbaddr\0" \ 621 "norbootworking=setenv bootargs $workingbootargs" \ 622 " console=$consoledev,$baudrate $othbootargs; " \ 623 "run norloadworking; " \ 624 "bootm $kerneladdr - $dtbaddr\0" \ 625 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ 626 "setenv cramfsaddr $nor_recoveryaddr; " \ 627 "cramfsload $dtbaddr $dtbfile; " \ 628 "cramfsload $kerneladdr $kernelfile\0" \ 629 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ 630 "setenv cramfsaddr $nor_workingaddr; " \ 631 "cramfsload $dtbaddr $dtbfile; " \ 632 "cramfsload $kerneladdr $kernelfile\0" \ 633 "prog_spi_mbr=run spi__mbr\0" \ 634 "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \ 635 "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \ 636 "run spi__cramfs\0" \ 637 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ 638 " console=$consoledev,$baudrate $othbootargs; " \ 639 "tftp $rootfsaddr $rootfsfile; " \ 640 "tftp $loadaddr $kernelfile; " \ 641 "tftp $dtbaddr $dtbfile; " \ 642 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ 643 "ramdisk_size=120000\0" \ 644 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 645 "recoveryaddr=0x02F00000\0" \ 646 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ 647 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ 648 "mw.l 0xffe0f008 0x00400000\0" \ 649 "rootfsaddr=0x02F00000\0" \ 650 "rootfsfile=rootfs.ext2.gz.uboot\0" \ 651 "rootpath=/opt/nfsroot\0" \ 652 "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ 653 "protect off 0xeC000000 +$filesize; " \ 654 "erase 0xEC000000 +$filesize; " \ 655 "cp.b $loadaddr 0xEC000000 $filesize; " \ 656 "cmp.b $loadaddr 0xEC000000 $filesize; " \ 657 "protect on 0xeC000000 +$filesize\0" \ 658 "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ 659 "protect off 0xeFF80000 +$filesize; " \ 660 "erase 0xEFF80000 +$filesize; " \ 661 "cp.b $loadaddr 0xEFF80000 $filesize; " \ 662 "cmp.b $loadaddr 0xEFF80000 $filesize; " \ 663 "protect on 0xeFF80000 +$filesize\0" \ 664 "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \ 665 "sf probe 0; sf erase 0x8000 +$filesize; " \ 666 "sf write $loadaddr 0x8000 $filesize\0" \ 667 "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \ 668 "protect off 0xec0a0000 +$filesize; " \ 669 "erase 0xeC0A0000 +$filesize; " \ 670 "cp.b $loadaddr 0xeC0A0000 $filesize; " \ 671 "protect on 0xec0a0000 +$filesize\0" \ 672 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ 673 "sf probe 1; sf erase 0 +$filesize; " \ 674 "sf write $loadaddr 0 $filesize\0" \ 675 "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ 676 "sf probe 0; sf erase 0 +$filesize; " \ 677 "sf write $loadaddr 0 $filesize\0" \ 678 "tftpflash=tftpboot $loadaddr $uboot; " \ 679 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 680 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 681 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ 682 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 683 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ 684 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ 685 "ubootaddr=0x01000000\0" \ 686 "ubootfile=u-boot.bin\0" \ 687 "ubootd=u-boot4dongle.bin\0" \ 688 "upgrade=run flashworking\0" \ 689 "usb_phy_type=ulpi\0 " \ 690 "workingaddr=0x02F00000\0" \ 691 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" 692 693 #else 694 695 #if defined(CONFIG_UCP1020T1) 696 697 #define CONFIG_EXTRA_ENV_SETTINGS \ 698 "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \ 699 "bootfile=uImage\0" \ 700 "consoledev=ttyS0\0" \ 701 "cramfsfile=image.cramfs\0" \ 702 "dtbaddr=0x00c00000\0" \ 703 "dtbfile=image.dtb\0" \ 704 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ 705 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ 706 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ 707 "fileaddr=0x01000000\0" \ 708 "filesize=0x00080000\0" \ 709 "flashmbr=sf probe 0; " \ 710 "tftp $loadaddr $mbr; " \ 711 "sf erase $mbr_offset +$filesize; " \ 712 "sf write $loadaddr $mbr_offset $filesize\0" \ 713 "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ 714 "protect off $nor_recoveryaddr +$filesize; " \ 715 "erase $nor_recoveryaddr +$filesize; " \ 716 "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ 717 "protect on $nor_recoveryaddr +$filesize\0 " \ 718 "flashuboot=tftp $ubootaddr $ubootfile; " \ 719 "protect off $nor_ubootaddr +$filesize; " \ 720 "erase $nor_ubootaddr +$filesize; " \ 721 "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ 722 "protect on $nor_ubootaddr +$filesize\0 " \ 723 "flashworking=tftp $workingaddr $cramfsfile; " \ 724 "protect off $nor_workingaddr +$filesize; " \ 725 "erase $nor_workingaddr +$filesize; " \ 726 "cp.b $workingaddr $nor_workingaddr $filesize; " \ 727 "protect on $nor_workingaddr +$filesize\0 " \ 728 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ 729 "kerneladdr=0x01100000\0" \ 730 "kernelfile=uImage\0" \ 731 "loadaddr=0x01000000\0" \ 732 "mbr=uCP1020.mbr\0" \ 733 "mbr_offset=0x00000000\0" \ 734 "netdev=eth0\0" \ 735 "nor_recoveryaddr=0xEC0A0000\0" \ 736 "nor_ubootaddr=0xEFF80000\0" \ 737 "nor_workingaddr=0xECFA0000\0" \ 738 "norbootrecovery=setenv bootargs $recoverybootargs" \ 739 " console=$consoledev,$baudrate $othbootargs; " \ 740 "run norloadrecovery; " \ 741 "bootm $kerneladdr - $dtbaddr\0" \ 742 "norbootworking=setenv bootargs $workingbootargs" \ 743 " console=$consoledev,$baudrate $othbootargs; " \ 744 "run norloadworking; " \ 745 "bootm $kerneladdr - $dtbaddr\0" \ 746 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ 747 "setenv cramfsaddr $nor_recoveryaddr; " \ 748 "cramfsload $dtbaddr $dtbfile; " \ 749 "cramfsload $kerneladdr $kernelfile\0" \ 750 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ 751 "setenv cramfsaddr $nor_workingaddr; " \ 752 "cramfsload $dtbaddr $dtbfile; " \ 753 "cramfsload $kerneladdr $kernelfile\0" \ 754 "othbootargs=quiet\0" \ 755 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ 756 " console=$consoledev,$baudrate $othbootargs; " \ 757 "tftp $rootfsaddr $rootfsfile; " \ 758 "tftp $loadaddr $kernelfile; " \ 759 "tftp $dtbaddr $dtbfile; " \ 760 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ 761 "ramdisk_size=120000\0" \ 762 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 763 "recoveryaddr=0x02F00000\0" \ 764 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ 765 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ 766 "mw.l 0xffe0f008 0x00400000\0" \ 767 "rootfsaddr=0x02F00000\0" \ 768 "rootfsfile=rootfs.ext2.gz.uboot\0" \ 769 "rootpath=/opt/nfsroot\0" \ 770 "silent=1\0" \ 771 "tftpflash=tftpboot $loadaddr $uboot; " \ 772 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 773 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 774 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ 775 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 776 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ 777 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ 778 "ubootaddr=0x01000000\0" \ 779 "ubootfile=u-boot.bin\0" \ 780 "upgrade=run flashworking\0" \ 781 "workingaddr=0x02F00000\0" \ 782 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" 783 784 #else /* For Arcturus Modules */ 785 786 #define CONFIG_EXTRA_ENV_SETTINGS \ 787 "bootcmd=run norkernel\0" \ 788 "bootfile=uImage\0" \ 789 "consoledev=ttyS0\0" \ 790 "dtbaddr=0x00c00000\0" \ 791 "dtbfile=image.dtb\0" \ 792 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ 793 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ 794 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ 795 "fileaddr=0x01000000\0" \ 796 "filesize=0x00080000\0" \ 797 "flashmbr=sf probe 0; " \ 798 "tftp $loadaddr $mbr; " \ 799 "sf erase $mbr_offset +$filesize; " \ 800 "sf write $loadaddr $mbr_offset $filesize\0" \ 801 "flashuboot=tftp $loadaddr $ubootfile; " \ 802 "protect off $nor_ubootaddr0 +$filesize; " \ 803 "erase $nor_ubootaddr0 +$filesize; " \ 804 "cp.b $loadaddr $nor_ubootaddr0 $filesize; " \ 805 "protect on $nor_ubootaddr0 +$filesize; " \ 806 "protect off $nor_ubootaddr1 +$filesize; " \ 807 "erase $nor_ubootaddr1 +$filesize; " \ 808 "cp.b $loadaddr $nor_ubootaddr1 $filesize; " \ 809 "protect on $nor_ubootaddr1 +$filesize\0 " \ 810 "format0=protect off $part0base +$part0size; " \ 811 "erase $part0base +$part0size\0" \ 812 "format1=protect off $part1base +$part1size; " \ 813 "erase $part1base +$part1size\0" \ 814 "format2=protect off $part2base +$part2size; " \ 815 "erase $part2base +$part2size\0" \ 816 "format3=protect off $part3base +$part3size; " \ 817 "erase $part3base +$part3size\0" \ 818 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ 819 "kerneladdr=0x01100000\0" \ 820 "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \ 821 "kernelfile=uImage\0" \ 822 "loadaddr=0x01000000\0" \ 823 "mbr=uCP1020.mbr\0" \ 824 "mbr_offset=0x00000000\0" \ 825 "netdev=eth0\0" \ 826 "nor_ubootaddr0=0xEC000000\0" \ 827 "nor_ubootaddr1=0xEFF80000\0" \ 828 "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \ 829 "run norkernelload; " \ 830 "bootm $kerneladdr - $dtbaddr\0" \ 831 "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \ 832 "setenv cramfsaddr $part0base; " \ 833 "cramfsload $dtbaddr $dtbfile; " \ 834 "cramfsload $kerneladdr $kernelfile\0" \ 835 "part0base=0xEC100000\0" \ 836 "part0size=0x00700000\0" \ 837 "part1base=0xEC800000\0" \ 838 "part1size=0x02000000\0" \ 839 "part2base=0xEE800000\0" \ 840 "part2size=0x00800000\0" \ 841 "part3base=0xEF000000\0" \ 842 "part3size=0x00F80000\0" \ 843 "partENVbase=0xEC080000\0" \ 844 "partENVsize=0x00080000\0" \ 845 "program0=tftp part0-000000.bin; " \ 846 "protect off $part0base +$filesize; " \ 847 "erase $part0base +$filesize; " \ 848 "cp.b $loadaddr $part0base $filesize; " \ 849 "echo Verifying...; " \ 850 "cmp.b $loadaddr $part0base $filesize\0" \ 851 "program1=tftp part1-000000.bin; " \ 852 "protect off $part1base +$filesize; " \ 853 "erase $part1base +$filesize; " \ 854 "cp.b $loadaddr $part1base $filesize; " \ 855 "echo Verifying...; " \ 856 "cmp.b $loadaddr $part1base $filesize\0" \ 857 "program2=tftp part2-000000.bin; " \ 858 "protect off $part2base +$filesize; " \ 859 "erase $part2base +$filesize; " \ 860 "cp.b $loadaddr $part2base $filesize; " \ 861 "echo Verifying...; " \ 862 "cmp.b $loadaddr $part2base $filesize\0" \ 863 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ 864 " console=$consoledev,$baudrate $othbootargs; " \ 865 "tftp $rootfsaddr $rootfsfile; " \ 866 "tftp $loadaddr $kernelfile; " \ 867 "tftp $dtbaddr $dtbfile; " \ 868 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ 869 "ramdisk_size=120000\0" \ 870 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 871 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ 872 "mw.l 0xffe0f008 0x00400000\0" \ 873 "rootfsaddr=0x02F00000\0" \ 874 "rootfsfile=rootfs.ext2.gz.uboot\0" \ 875 "rootpath=/opt/nfsroot\0" \ 876 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ 877 "sf probe 0; sf erase 0 +$filesize; " \ 878 "sf write $loadaddr 0 $filesize\0" \ 879 "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ 880 "protect off 0xeC000000 +$filesize; " \ 881 "erase 0xEC000000 +$filesize; " \ 882 "cp.b $loadaddr 0xEC000000 $filesize; " \ 883 "cmp.b $loadaddr 0xEC000000 $filesize; " \ 884 "protect on 0xeC000000 +$filesize\0" \ 885 "tftpflash=tftpboot $loadaddr $uboot; " \ 886 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 887 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 888 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ 889 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 890 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ 891 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ 892 "ubootfile=u-boot.bin\0" \ 893 "upgrade=run flashuboot\0" \ 894 "usb_phy_type=ulpi\0 " \ 895 "boot_nfs= " \ 896 "setenv bootargs root=/dev/nfs rw " \ 897 "nfsroot=$serverip:$rootpath " \ 898 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 899 "console=$consoledev,$baudrate $othbootargs;" \ 900 "tftp $loadaddr $bootfile;" \ 901 "tftp $fdtaddr $fdtfile;" \ 902 "bootm $loadaddr - $fdtaddr\0" \ 903 "boot_hd = " \ 904 "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ 905 "console=$consoledev,$baudrate $othbootargs;" \ 906 "usb start;" \ 907 "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ 908 "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ 909 "bootm $loadaddr - $fdtaddr\0" \ 910 "boot_usb_fat = " \ 911 "setenv bootargs root=/dev/ram rw " \ 912 "console=$consoledev,$baudrate $othbootargs " \ 913 "ramdisk_size=$ramdisk_size;" \ 914 "usb start;" \ 915 "fatload usb 0:2 $loadaddr $bootfile;" \ 916 "fatload usb 0:2 $fdtaddr $fdtfile;" \ 917 "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ 918 "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ 919 "boot_usb_ext2 = " \ 920 "setenv bootargs root=/dev/ram rw " \ 921 "console=$consoledev,$baudrate $othbootargs " \ 922 "ramdisk_size=$ramdisk_size;" \ 923 "usb start;" \ 924 "ext2load usb 0:4 $loadaddr $bootfile;" \ 925 "ext2load usb 0:4 $fdtaddr $fdtfile;" \ 926 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ 927 "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ 928 "boot_nor = " \ 929 "setenv bootargs root=/dev/$jffs2nor rw " \ 930 "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ 931 "bootm $norbootaddr - $norfdtaddr\0 " \ 932 "boot_ram = " \ 933 "setenv bootargs root=/dev/ram rw " \ 934 "console=$consoledev,$baudrate $othbootargs " \ 935 "ramdisk_size=$ramdisk_size;" \ 936 "tftp $ramdiskaddr $ramdiskfile;" \ 937 "tftp $loadaddr $bootfile;" \ 938 "tftp $fdtaddr $fdtfile;" \ 939 "bootm $loadaddr $ramdiskaddr $fdtaddr\0" 940 941 #endif 942 #endif 943 944 #endif /* __CONFIG_H */ 945