1 /* 2 * Copyright 2013-2015 Arcturus Networks, Inc. 3 * http://www.arcturusnetworks.com/products/ucp1020/ 4 * based on include/configs/p1_p2_rdb_pc.h 5 * original copyright follows: 6 * Copyright 2009-2011 Freescale Semiconductor, Inc. 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 /* 12 * QorIQ uCP1020-xx boards configuration file 13 */ 14 #ifndef __CONFIG_H 15 #define __CONFIG_H 16 17 #define CONFIG_DISPLAY_BOARDINFO 18 19 #define CONFIG_FSL_ELBC 20 #define CONFIG_PCI 21 #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */ 22 #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */ 23 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 24 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ 25 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 26 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 27 28 #if defined(CONFIG_TARTGET_UCP1020T1) 29 30 #define CONFIG_UCP1020_REV_1_3 31 32 #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1" 33 #define CONFIG_P1020 34 35 #define CONFIG_TSEC_ENET 36 #define CONFIG_TSEC1 37 #define CONFIG_TSEC3 38 #define CONFIG_HAS_ETH0 39 #define CONFIG_HAS_ETH1 40 #define CONFIG_ETHADDR 00:19:D3:FF:FF:FF 41 #define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE 42 #define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD 43 #define CONFIG_IPADDR 10.80.41.229 44 #define CONFIG_SERVERIP 10.80.41.227 45 #define CONFIG_NETMASK 255.255.252.0 46 #define CONFIG_ETHPRIME "eTSEC3" 47 48 #ifndef CONFIG_SPI_FLASH 49 #endif 50 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT 51 52 #define CONFIG_MMC 53 #define CONFIG_SYS_L2_SIZE (256 << 10) 54 55 #define CONFIG_LAST_STAGE_INIT 56 57 #if !defined(CONFIG_DONGLE) 58 #define CONFIG_SILENT_CONSOLE 59 #endif 60 61 #endif 62 63 #if defined(CONFIG_TARGET_UCP1020) 64 65 #define CONFIG_UCP1020 66 #define CONFIG_UCP1020_REV_1_3 67 68 #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR" 69 #define CONFIG_P1020 70 71 #define CONFIG_TSEC_ENET 72 #define CONFIG_TSEC1 73 #define CONFIG_TSEC2 74 #define CONFIG_TSEC3 75 #define CONFIG_HAS_ETH0 76 #define CONFIG_HAS_ETH1 77 #define CONFIG_HAS_ETH2 78 #define CONFIG_ETHADDR 00:06:3B:FF:FF:FF 79 #define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE 80 #define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD 81 #define CONFIG_IPADDR 192.168.1.81 82 #define CONFIG_IPADDR1 192.168.1.82 83 #define CONFIG_IPADDR2 192.168.1.83 84 #define CONFIG_SERVERIP 192.168.1.80 85 #define CONFIG_GATEWAYIP 102.168.1.1 86 #define CONFIG_NETMASK 255.255.255.0 87 #define CONFIG_ETHPRIME "eTSEC1" 88 89 #ifndef CONFIG_SPI_FLASH 90 #endif 91 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT 92 93 #define CONFIG_MMC 94 #define CONFIG_SYS_L2_SIZE (256 << 10) 95 96 #define CONFIG_LAST_STAGE_INIT 97 98 #endif 99 100 #ifdef CONFIG_SDCARD 101 #define CONFIG_RAMBOOT_SDCARD 102 #define CONFIG_SYS_RAMBOOT 103 #define CONFIG_SYS_EXTRA_ENV_RELOC 104 #define CONFIG_SYS_TEXT_BASE 0x11000000 105 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc 106 #endif 107 108 #ifdef CONFIG_SPIFLASH 109 #define CONFIG_RAMBOOT_SPIFLASH 110 #define CONFIG_SYS_RAMBOOT 111 #define CONFIG_SYS_EXTRA_ENV_RELOC 112 #define CONFIG_SYS_TEXT_BASE 0x11000000 113 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc 114 #endif 115 116 #ifndef CONFIG_SYS_TEXT_BASE 117 #define CONFIG_SYS_TEXT_BASE 0xeff80000 118 #endif 119 #define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000 120 121 #ifndef CONFIG_RESET_VECTOR_ADDRESS 122 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 123 #endif 124 125 #ifndef CONFIG_SYS_MONITOR_BASE 126 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 127 #endif 128 129 /* High Level Configuration Options */ 130 #define CONFIG_BOOKE 131 #define CONFIG_E500 132 /* #define CONFIG_MPC85xx */ 133 134 #define CONFIG_MP 135 136 #define CONFIG_FSL_LAW 137 138 #define CONFIG_ENV_OVERWRITE 139 140 #define CONFIG_CMD_SATA 141 #define CONFIG_SATA_SIL 142 #define CONFIG_SYS_SATA_MAX_DEVICE 2 143 #define CONFIG_LIBATA 144 #define CONFIG_LBA48 145 146 #define CONFIG_SYS_CLK_FREQ 66666666 147 #define CONFIG_DDR_CLK_FREQ 66666666 148 149 #define CONFIG_HWCONFIG 150 151 #define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */ 152 #define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */ 153 #define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */ 154 /* 155 * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details). 156 * there will be one entry in this array for each two (dummy) sensors in 157 * CONFIG_DTT_SENSORS. 158 * 159 * For uCP1020 module: 160 * - only one ADM1021/NCT72 161 * - i2c addr 0x41 162 * - conversion rate 0x02 = 0.25 conversions/second 163 * - ALERT output disabled 164 * - local temp sensor enabled, min set to 0 deg, max set to 85 deg 165 * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg 166 */ 167 #define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \ 168 0x02, 0, 1, 0, 85, 1, 0, 85} } 169 170 #define CONFIG_CMD_DTT 171 172 /* 173 * These can be toggled for performance analysis, otherwise use default. 174 */ 175 #define CONFIG_L2_CACHE 176 #define CONFIG_BTB 177 178 #define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ 179 180 #define CONFIG_ENABLE_36BIT_PHYS 181 182 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 183 #define CONFIG_SYS_MEMTEST_END 0x1fffffff 184 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 185 186 #define CONFIG_SYS_CCSRBAR 0xffe00000 187 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 188 189 /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k 190 SPL code*/ 191 #ifdef CONFIG_SPL_BUILD 192 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 193 #endif 194 195 /* DDR Setup */ 196 #define CONFIG_DDR_ECC_ENABLE 197 #define CONFIG_SYS_FSL_DDR3 198 #ifndef CONFIG_DDR_ECC_ENABLE 199 #define CONFIG_SYS_DDR_RAW_TIMING 200 #define CONFIG_DDR_SPD 201 #endif 202 #define CONFIG_SYS_SPD_BUS_NUM 1 203 #undef CONFIG_FSL_DDR_INTERACTIVE 204 205 #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M 206 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 207 #define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) 208 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 209 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 210 211 #define CONFIG_NUM_DDR_CONTROLLERS 1 212 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 213 214 /* Default settings for DDR3 */ 215 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f 216 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 217 #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 218 #define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f 219 #define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302 220 #define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 221 222 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 223 #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 224 #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 225 #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 226 227 #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 228 #define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608 229 #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 230 #define CONFIG_SYS_DDR_RCW_1 0x00000000 231 #define CONFIG_SYS_DDR_RCW_2 0x00000000 232 #ifdef CONFIG_DDR_ECC_ENABLE 233 #define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */ 234 #else 235 #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ 236 #endif 237 #define CONFIG_SYS_DDR_CONTROL_2 0x04401050 238 #define CONFIG_SYS_DDR_TIMING_4 0x00220001 239 #define CONFIG_SYS_DDR_TIMING_5 0x03402400 240 241 #define CONFIG_SYS_DDR_TIMING_3 0x00020000 242 #define CONFIG_SYS_DDR_TIMING_0 0x00330004 243 #define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846 244 #define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF 245 #define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 246 #define CONFIG_SYS_DDR_MODE_1 0x40461520 247 #define CONFIG_SYS_DDR_MODE_2 0x8000c000 248 #define CONFIG_SYS_DDR_INTERVAL 0x0C300000 249 250 #undef CONFIG_CLOCKS_IN_MHZ 251 252 /* 253 * Memory map 254 * 255 * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable 256 * 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2) 257 * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1 258 * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable 259 * (early boot only) 260 * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable 261 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable 262 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable 263 */ 264 265 /* 266 * Local Bus Definitions 267 */ 268 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ 269 #define CONFIG_SYS_FLASH_BASE 0xec000000 270 271 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 272 273 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 274 | BR_PS_16 | BR_V) 275 276 #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 277 278 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} 279 #define CONFIG_SYS_FLASH_QUIET_TEST 280 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 281 282 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 283 284 #undef CONFIG_SYS_FLASH_CHECKSUM 285 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 286 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 287 288 #define CONFIG_FLASH_CFI_DRIVER 289 #define CONFIG_SYS_FLASH_CFI 290 #define CONFIG_SYS_FLASH_EMPTY_INFO 291 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 292 293 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 294 295 #define CONFIG_SYS_INIT_RAM_LOCK 296 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ 297 /* Initial L1 address */ 298 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR 299 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 300 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 301 /* Size of used area in RAM */ 302 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 303 304 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 305 GENERATED_GBL_DATA_SIZE) 306 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 307 308 #define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */ 309 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */ 310 311 #define CONFIG_SYS_PMC_BASE 0xff980000 312 #define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE 313 #define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \ 314 BR_PS_8 | BR_V) 315 #define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ 316 OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \ 317 OR_GPCM_EAD) 318 319 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 320 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 321 #ifdef CONFIG_NAND_FSL_ELBC 322 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */ 323 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 324 #endif 325 326 /* Serial Port - controlled on board with jumper J8 327 * open - index 2 328 * shorted - index 1 329 */ 330 #define CONFIG_CONS_INDEX 1 331 #undef CONFIG_SERIAL_SOFTWARE_FIFO 332 #define CONFIG_SYS_NS16550_SERIAL 333 #define CONFIG_SYS_NS16550_REG_SIZE 1 334 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 335 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL) 336 #define CONFIG_NS16550_MIN_FUNCTIONS 337 #endif 338 339 #define CONFIG_SYS_BAUDRATE_TABLE \ 340 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 341 342 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) 343 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) 344 345 /* Use the HUSH parser */ 346 #define CONFIG_SYS_HUSH_PARSER 347 348 /* 349 * Pass open firmware flat tree 350 */ 351 #define CONFIG_OF_LIBFDT 352 #define CONFIG_OF_BOARD_SETUP 353 #define CONFIG_OF_STDOUT_VIA_ALIAS 354 355 /* new uImage format support */ 356 #define CONFIG_FIT 357 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 358 359 /* I2C */ 360 #define CONFIG_SYS_I2C 361 #define CONFIG_SYS_I2C_FSL 362 #define CONFIG_SYS_FSL_I2C_SPEED 400000 363 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 364 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 365 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 366 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 367 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 368 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } 369 #define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */ 370 371 #define CONFIG_RTC_DS1337 372 #define CONFIG_SYS_RTC_DS1337_NOOSC 373 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 374 #define CONFIG_SYS_I2C_PCA9557_ADDR 0x18 375 #define CONFIG_SYS_I2C_NCT72_ADDR 0x4C 376 #define CONFIG_SYS_I2C_IDT6V49205B 0x69 377 378 /* 379 * eSPI - Enhanced SPI 380 */ 381 #define CONFIG_HARD_SPI 382 383 #define CONFIG_CMD_SF 1 384 #define CONFIG_CMD_SPI 1 385 #define CONFIG_SF_DEFAULT_SPEED 10000000 386 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 387 388 #if defined(CONFIG_PCI) 389 /* 390 * General PCI 391 * Memory space is mapped 1-1, but I/O space must start from 0. 392 */ 393 394 /* controller 2, direct to uli, tgtid 2, Base address 9000 */ 395 #define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9" 396 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 397 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 398 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 399 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 400 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 401 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 402 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 403 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 404 405 /* controller 1, Slot 2, tgtid 1, Base address a000 */ 406 #define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10" 407 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 408 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 409 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 410 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 411 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 412 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 413 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 414 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 415 416 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 417 #define CONFIG_CMD_PCI 418 419 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 420 #define CONFIG_DOS_PARTITION 421 #endif /* CONFIG_PCI */ 422 423 /* 424 * Environment 425 */ 426 #ifdef CONFIG_ENV_FIT_UCBOOT 427 428 #define CONFIG_ENV_IS_IN_FLASH 429 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000) 430 #define CONFIG_ENV_SIZE 0x20000 431 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 432 433 #else 434 435 #define CONFIG_ENV_SPI_BUS 0 436 #define CONFIG_ENV_SPI_CS 0 437 #define CONFIG_ENV_SPI_MAX_HZ 10000000 438 #define CONFIG_ENV_SPI_MODE 0 439 440 #ifdef CONFIG_RAMBOOT_SPIFLASH 441 442 #define CONFIG_ENV_IS_IN_SPI_FLASH 443 #define CONFIG_ENV_SIZE 0x3000 /* 12KB */ 444 #define CONFIG_ENV_OFFSET 0x2000 /* 8KB */ 445 #define CONFIG_ENV_SECT_SIZE 0x1000 446 447 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) 448 /* Address and size of Redundant Environment Sector */ 449 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) 450 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 451 #endif 452 453 #elif defined(CONFIG_RAMBOOT_SDCARD) 454 #define CONFIG_ENV_IS_IN_MMC 455 #define CONFIG_FSL_FIXED_MMC_LOCATION 456 #define CONFIG_ENV_SIZE 0x2000 457 #define CONFIG_SYS_MMC_ENV_DEV 0 458 459 #elif defined(CONFIG_SYS_RAMBOOT) 460 #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ 461 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 462 #define CONFIG_ENV_SIZE 0x2000 463 464 #else 465 #define CONFIG_ENV_IS_IN_FLASH 466 #define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE) 467 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 468 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE 469 #define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000) 470 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) 471 /* Address and size of Redundant Environment Sector */ 472 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) 473 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 474 #endif 475 476 #endif 477 478 #endif /* CONFIG_ENV_FIT_UCBOOT */ 479 480 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 481 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 482 483 /* 484 * Command line configuration. 485 */ 486 #define CONFIG_CMD_IRQ 487 #define CONFIG_CMD_PING 488 #define CONFIG_CMD_I2C 489 #define CONFIG_CMD_MII 490 #define CONFIG_CMD_DATE 491 #define CONFIG_CMD_I2C 492 #define CONFIG_CMD_IRQ 493 #define CONFIG_CMD_MII 494 #define CONFIG_CMD_PING 495 #define CONFIG_CMD_REGINFO 496 #define CONFIG_CMD_ERRATA 497 #define CONFIG_CMD_CRAMFS 498 499 /* 500 * USB 501 */ 502 #define CONFIG_HAS_FSL_DR_USB 503 504 #if defined(CONFIG_HAS_FSL_DR_USB) 505 #define CONFIG_USB_EHCI 506 507 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 508 509 #ifdef CONFIG_USB_EHCI 510 #define CONFIG_CMD_USB 511 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 512 #define CONFIG_USB_EHCI_FSL 513 #define CONFIG_USB_STORAGE 514 #endif 515 #endif 516 517 #undef CONFIG_WATCHDOG /* watchdog disabled */ 518 519 #ifdef CONFIG_MMC 520 #define CONFIG_FSL_ESDHC 521 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 522 #define CONFIG_CMD_MMC 523 #define CONFIG_MMC_SPI 524 #define CONFIG_CMD_MMC_SPI 525 #define CONFIG_GENERIC_MMC 526 #endif 527 528 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA) 529 #define CONFIG_CMD_EXT2 530 #define CONFIG_CMD_FAT 531 #define CONFIG_DOS_PARTITION 532 #endif 533 534 /* Misc Extra Settings */ 535 #undef CONFIG_WATCHDOG /* watchdog disabled */ 536 537 /* 538 * Miscellaneous configurable options 539 */ 540 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 541 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 542 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 543 #if defined(CONFIG_CMD_KGDB) 544 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 545 #else 546 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 547 #endif 548 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 549 /* Print Buffer Size */ 550 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 551 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 552 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */ 553 554 /* 555 * For booting Linux, the board info and command line data 556 * have to be in the first 64 MB of memory, since this is 557 * the maximum mapped by the Linux kernel during initialization. 558 */ 559 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ 560 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 561 562 #if defined(CONFIG_CMD_KGDB) 563 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 564 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 565 #endif 566 567 /* 568 * Environment Configuration 569 */ 570 571 #if defined(CONFIG_TSEC_ENET) 572 573 #if defined(CONFIG_UCP1020_REV_1_2) 574 #define CONFIG_PHY_MICREL_KSZ9021 575 #elif defined(CONFIG_UCP1020_REV_1_3) 576 #define CONFIG_PHY_MICREL_KSZ9031 577 #else 578 #error "UCP1020 module revision is not defined !!!" 579 #endif 580 581 #define CONFIG_CMD_DHCP 582 #define CONFIG_BOOTP_SERVERIP 583 584 #define CONFIG_MII /* MII PHY management */ 585 #define CONFIG_TSEC1_NAME "eTSEC1" 586 #define CONFIG_TSEC2_NAME "eTSEC2" 587 #define CONFIG_TSEC3_NAME "eTSEC3" 588 589 #define TSEC1_PHY_ADDR 4 590 #define TSEC2_PHY_ADDR 0 591 #define TSEC2_PHY_ADDR_SGMII 0x00 592 #define TSEC3_PHY_ADDR 6 593 594 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 595 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 596 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 597 598 #define TSEC1_PHYIDX 0 599 #define TSEC2_PHYIDX 0 600 #define TSEC3_PHYIDX 0 601 602 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 603 604 #endif 605 606 #define CONFIG_HOSTNAME UCP1020 607 #define CONFIG_ROOTPATH "/opt/nfsroot" 608 #define CONFIG_BOOTFILE "uImage" 609 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 610 611 /* default location for tftp and bootm */ 612 #define CONFIG_LOADADDR 1000000 613 614 #define CONFIG_BOOTARGS /* the boot command will set bootargs */ 615 616 #define CONFIG_BAUDRATE 115200 617 618 #if defined(CONFIG_DONGLE) 619 620 #define CONFIG_BOOTDELAY 1 /* autoboot after 1 seconds */ 621 #define CONFIG_EXTRA_ENV_SETTINGS \ 622 "bootcmd=run prog_spi_mbrbootcramfs\0" \ 623 "bootfile=uImage\0" \ 624 "consoledev=ttyS0\0" \ 625 "cramfsfile=image.cramfs\0" \ 626 "dtbaddr=0x00c00000\0" \ 627 "dtbfile=image.dtb\0" \ 628 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ 629 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ 630 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ 631 "fileaddr=0x01000000\0" \ 632 "filesize=0x00080000\0" \ 633 "flashmbr=sf probe 0; " \ 634 "tftp $loadaddr $mbr; " \ 635 "sf erase $mbr_offset +$filesize; " \ 636 "sf write $loadaddr $mbr_offset $filesize\0" \ 637 "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ 638 "protect off $nor_recoveryaddr +$filesize; " \ 639 "erase $nor_recoveryaddr +$filesize; " \ 640 "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ 641 "protect on $nor_recoveryaddr +$filesize\0 " \ 642 "flashuboot=tftp $ubootaddr $ubootfile; " \ 643 "protect off $nor_ubootaddr +$filesize; " \ 644 "erase $nor_ubootaddr +$filesize; " \ 645 "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ 646 "protect on $nor_ubootaddr +$filesize\0 " \ 647 "flashworking=tftp $workingaddr $cramfsfile; " \ 648 "protect off $nor_workingaddr +$filesize; " \ 649 "erase $nor_workingaddr +$filesize; " \ 650 "cp.b $workingaddr $nor_workingaddr $filesize; " \ 651 "protect on $nor_workingaddr +$filesize\0 " \ 652 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ 653 "kerneladdr=0x01100000\0" \ 654 "kernelfile=uImage\0" \ 655 "loadaddr=0x01000000\0" \ 656 "mbr=uCP1020d.mbr\0" \ 657 "mbr_offset=0x00000000\0" \ 658 "mmbr=uCP1020Quiet.mbr\0" \ 659 "mmcpart=0:2\0" \ 660 "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ 661 "mmc erase 1 1; " \ 662 "mmc write $loadaddr 1 1\0" \ 663 "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \ 664 "mmc erase 0x40 0x400; " \ 665 "mmc write $loadaddr 0x40 0x400\0" \ 666 "netdev=eth0\0" \ 667 "nor_recoveryaddr=0xEC0A0000\0" \ 668 "nor_ubootaddr=0xEFF80000\0" \ 669 "nor_workingaddr=0xECFA0000\0" \ 670 "norbootrecovery=setenv bootargs $recoverybootargs" \ 671 " console=$consoledev,$baudrate $othbootargs; " \ 672 "run norloadrecovery; " \ 673 "bootm $kerneladdr - $dtbaddr\0" \ 674 "norbootworking=setenv bootargs $workingbootargs" \ 675 " console=$consoledev,$baudrate $othbootargs; " \ 676 "run norloadworking; " \ 677 "bootm $kerneladdr - $dtbaddr\0" \ 678 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ 679 "setenv cramfsaddr $nor_recoveryaddr; " \ 680 "cramfsload $dtbaddr $dtbfile; " \ 681 "cramfsload $kerneladdr $kernelfile\0" \ 682 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ 683 "setenv cramfsaddr $nor_workingaddr; " \ 684 "cramfsload $dtbaddr $dtbfile; " \ 685 "cramfsload $kerneladdr $kernelfile\0" \ 686 "prog_spi_mbr=run spi__mbr\0" \ 687 "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \ 688 "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \ 689 "run spi__cramfs\0" \ 690 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ 691 " console=$consoledev,$baudrate $othbootargs; " \ 692 "tftp $rootfsaddr $rootfsfile; " \ 693 "tftp $loadaddr $kernelfile; " \ 694 "tftp $dtbaddr $dtbfile; " \ 695 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ 696 "ramdisk_size=120000\0" \ 697 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 698 "recoveryaddr=0x02F00000\0" \ 699 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ 700 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ 701 "mw.l 0xffe0f008 0x00400000\0" \ 702 "rootfsaddr=0x02F00000\0" \ 703 "rootfsfile=rootfs.ext2.gz.uboot\0" \ 704 "rootpath=/opt/nfsroot\0" \ 705 "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ 706 "protect off 0xeC000000 +$filesize; " \ 707 "erase 0xEC000000 +$filesize; " \ 708 "cp.b $loadaddr 0xEC000000 $filesize; " \ 709 "cmp.b $loadaddr 0xEC000000 $filesize; " \ 710 "protect on 0xeC000000 +$filesize\0" \ 711 "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ 712 "protect off 0xeFF80000 +$filesize; " \ 713 "erase 0xEFF80000 +$filesize; " \ 714 "cp.b $loadaddr 0xEFF80000 $filesize; " \ 715 "cmp.b $loadaddr 0xEFF80000 $filesize; " \ 716 "protect on 0xeFF80000 +$filesize\0" \ 717 "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \ 718 "sf probe 0; sf erase 0x8000 +$filesize; " \ 719 "sf write $loadaddr 0x8000 $filesize\0" \ 720 "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \ 721 "protect off 0xec0a0000 +$filesize; " \ 722 "erase 0xeC0A0000 +$filesize; " \ 723 "cp.b $loadaddr 0xeC0A0000 $filesize; " \ 724 "protect on 0xec0a0000 +$filesize\0" \ 725 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ 726 "sf probe 1; sf erase 0 +$filesize; " \ 727 "sf write $loadaddr 0 $filesize\0" \ 728 "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ 729 "sf probe 0; sf erase 0 +$filesize; " \ 730 "sf write $loadaddr 0 $filesize\0" \ 731 "tftpflash=tftpboot $loadaddr $uboot; " \ 732 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 733 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 734 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ 735 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 736 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ 737 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ 738 "ubootaddr=0x01000000\0" \ 739 "ubootfile=u-boot.bin\0" \ 740 "ubootd=u-boot4dongle.bin\0" \ 741 "upgrade=run flashworking\0" \ 742 "usb_phy_type=ulpi\0 " \ 743 "workingaddr=0x02F00000\0" \ 744 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" 745 746 #else 747 748 #if defined(CONFIG_UCP1020T1) 749 750 #define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */ 751 #define CONFIG_EXTRA_ENV_SETTINGS \ 752 "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \ 753 "bootfile=uImage\0" \ 754 "consoledev=ttyS0\0" \ 755 "cramfsfile=image.cramfs\0" \ 756 "dtbaddr=0x00c00000\0" \ 757 "dtbfile=image.dtb\0" \ 758 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ 759 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ 760 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ 761 "fileaddr=0x01000000\0" \ 762 "filesize=0x00080000\0" \ 763 "flashmbr=sf probe 0; " \ 764 "tftp $loadaddr $mbr; " \ 765 "sf erase $mbr_offset +$filesize; " \ 766 "sf write $loadaddr $mbr_offset $filesize\0" \ 767 "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ 768 "protect off $nor_recoveryaddr +$filesize; " \ 769 "erase $nor_recoveryaddr +$filesize; " \ 770 "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ 771 "protect on $nor_recoveryaddr +$filesize\0 " \ 772 "flashuboot=tftp $ubootaddr $ubootfile; " \ 773 "protect off $nor_ubootaddr +$filesize; " \ 774 "erase $nor_ubootaddr +$filesize; " \ 775 "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ 776 "protect on $nor_ubootaddr +$filesize\0 " \ 777 "flashworking=tftp $workingaddr $cramfsfile; " \ 778 "protect off $nor_workingaddr +$filesize; " \ 779 "erase $nor_workingaddr +$filesize; " \ 780 "cp.b $workingaddr $nor_workingaddr $filesize; " \ 781 "protect on $nor_workingaddr +$filesize\0 " \ 782 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ 783 "kerneladdr=0x01100000\0" \ 784 "kernelfile=uImage\0" \ 785 "loadaddr=0x01000000\0" \ 786 "mbr=uCP1020.mbr\0" \ 787 "mbr_offset=0x00000000\0" \ 788 "netdev=eth0\0" \ 789 "nor_recoveryaddr=0xEC0A0000\0" \ 790 "nor_ubootaddr=0xEFF80000\0" \ 791 "nor_workingaddr=0xECFA0000\0" \ 792 "norbootrecovery=setenv bootargs $recoverybootargs" \ 793 " console=$consoledev,$baudrate $othbootargs; " \ 794 "run norloadrecovery; " \ 795 "bootm $kerneladdr - $dtbaddr\0" \ 796 "norbootworking=setenv bootargs $workingbootargs" \ 797 " console=$consoledev,$baudrate $othbootargs; " \ 798 "run norloadworking; " \ 799 "bootm $kerneladdr - $dtbaddr\0" \ 800 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ 801 "setenv cramfsaddr $nor_recoveryaddr; " \ 802 "cramfsload $dtbaddr $dtbfile; " \ 803 "cramfsload $kerneladdr $kernelfile\0" \ 804 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ 805 "setenv cramfsaddr $nor_workingaddr; " \ 806 "cramfsload $dtbaddr $dtbfile; " \ 807 "cramfsload $kerneladdr $kernelfile\0" \ 808 "othbootargs=quiet\0" \ 809 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ 810 " console=$consoledev,$baudrate $othbootargs; " \ 811 "tftp $rootfsaddr $rootfsfile; " \ 812 "tftp $loadaddr $kernelfile; " \ 813 "tftp $dtbaddr $dtbfile; " \ 814 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ 815 "ramdisk_size=120000\0" \ 816 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 817 "recoveryaddr=0x02F00000\0" \ 818 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ 819 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ 820 "mw.l 0xffe0f008 0x00400000\0" \ 821 "rootfsaddr=0x02F00000\0" \ 822 "rootfsfile=rootfs.ext2.gz.uboot\0" \ 823 "rootpath=/opt/nfsroot\0" \ 824 "silent=1\0" \ 825 "tftpflash=tftpboot $loadaddr $uboot; " \ 826 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 827 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 828 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ 829 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 830 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ 831 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ 832 "ubootaddr=0x01000000\0" \ 833 "ubootfile=u-boot.bin\0" \ 834 "upgrade=run flashworking\0" \ 835 "workingaddr=0x02F00000\0" \ 836 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" 837 838 #else /* For Arcturus Modules */ 839 840 #define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */ 841 #define CONFIG_EXTRA_ENV_SETTINGS \ 842 "bootcmd=run norkernel\0" \ 843 "bootfile=uImage\0" \ 844 "consoledev=ttyS0\0" \ 845 "dtbaddr=0x00c00000\0" \ 846 "dtbfile=image.dtb\0" \ 847 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ 848 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ 849 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ 850 "fileaddr=0x01000000\0" \ 851 "filesize=0x00080000\0" \ 852 "flashmbr=sf probe 0; " \ 853 "tftp $loadaddr $mbr; " \ 854 "sf erase $mbr_offset +$filesize; " \ 855 "sf write $loadaddr $mbr_offset $filesize\0" \ 856 "flashuboot=tftp $loadaddr $ubootfile; " \ 857 "protect off $nor_ubootaddr0 +$filesize; " \ 858 "erase $nor_ubootaddr0 +$filesize; " \ 859 "cp.b $loadaddr $nor_ubootaddr0 $filesize; " \ 860 "protect on $nor_ubootaddr0 +$filesize; " \ 861 "protect off $nor_ubootaddr1 +$filesize; " \ 862 "erase $nor_ubootaddr1 +$filesize; " \ 863 "cp.b $loadaddr $nor_ubootaddr1 $filesize; " \ 864 "protect on $nor_ubootaddr1 +$filesize\0 " \ 865 "format0=protect off $part0base +$part0size; " \ 866 "erase $part0base +$part0size\0" \ 867 "format1=protect off $part1base +$part1size; " \ 868 "erase $part1base +$part1size\0" \ 869 "format2=protect off $part2base +$part2size; " \ 870 "erase $part2base +$part2size\0" \ 871 "format3=protect off $part3base +$part3size; " \ 872 "erase $part3base +$part3size\0" \ 873 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ 874 "kerneladdr=0x01100000\0" \ 875 "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \ 876 "kernelfile=uImage\0" \ 877 "loadaddr=0x01000000\0" \ 878 "mbr=uCP1020.mbr\0" \ 879 "mbr_offset=0x00000000\0" \ 880 "netdev=eth0\0" \ 881 "nor_ubootaddr0=0xEC000000\0" \ 882 "nor_ubootaddr1=0xEFF80000\0" \ 883 "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \ 884 "run norkernelload; " \ 885 "bootm $kerneladdr - $dtbaddr\0" \ 886 "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \ 887 "setenv cramfsaddr $part0base; " \ 888 "cramfsload $dtbaddr $dtbfile; " \ 889 "cramfsload $kerneladdr $kernelfile\0" \ 890 "part0base=0xEC100000\0" \ 891 "part0size=0x00700000\0" \ 892 "part1base=0xEC800000\0" \ 893 "part1size=0x02000000\0" \ 894 "part2base=0xEE800000\0" \ 895 "part2size=0x00800000\0" \ 896 "part3base=0xEF000000\0" \ 897 "part3size=0x00F80000\0" \ 898 "partENVbase=0xEC080000\0" \ 899 "partENVsize=0x00080000\0" \ 900 "program0=tftp part0-000000.bin; " \ 901 "protect off $part0base +$filesize; " \ 902 "erase $part0base +$filesize; " \ 903 "cp.b $loadaddr $part0base $filesize; " \ 904 "echo Verifying...; " \ 905 "cmp.b $loadaddr $part0base $filesize\0" \ 906 "program1=tftp part1-000000.bin; " \ 907 "protect off $part1base +$filesize; " \ 908 "erase $part1base +$filesize; " \ 909 "cp.b $loadaddr $part1base $filesize; " \ 910 "echo Verifying...; " \ 911 "cmp.b $loadaddr $part1base $filesize\0" \ 912 "program2=tftp part2-000000.bin; " \ 913 "protect off $part2base +$filesize; " \ 914 "erase $part2base +$filesize; " \ 915 "cp.b $loadaddr $part2base $filesize; " \ 916 "echo Verifying...; " \ 917 "cmp.b $loadaddr $part2base $filesize\0" \ 918 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ 919 " console=$consoledev,$baudrate $othbootargs; " \ 920 "tftp $rootfsaddr $rootfsfile; " \ 921 "tftp $loadaddr $kernelfile; " \ 922 "tftp $dtbaddr $dtbfile; " \ 923 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ 924 "ramdisk_size=120000\0" \ 925 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 926 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ 927 "mw.l 0xffe0f008 0x00400000\0" \ 928 "rootfsaddr=0x02F00000\0" \ 929 "rootfsfile=rootfs.ext2.gz.uboot\0" \ 930 "rootpath=/opt/nfsroot\0" \ 931 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ 932 "sf probe 0; sf erase 0 +$filesize; " \ 933 "sf write $loadaddr 0 $filesize\0" \ 934 "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ 935 "protect off 0xeC000000 +$filesize; " \ 936 "erase 0xEC000000 +$filesize; " \ 937 "cp.b $loadaddr 0xEC000000 $filesize; " \ 938 "cmp.b $loadaddr 0xEC000000 $filesize; " \ 939 "protect on 0xeC000000 +$filesize\0" \ 940 "tftpflash=tftpboot $loadaddr $uboot; " \ 941 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 942 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 943 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ 944 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 945 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ 946 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ 947 "ubootfile=u-boot.bin\0" \ 948 "upgrade=run flashuboot\0" \ 949 "usb_phy_type=ulpi\0 " \ 950 "boot_nfs= " \ 951 "setenv bootargs root=/dev/nfs rw " \ 952 "nfsroot=$serverip:$rootpath " \ 953 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 954 "console=$consoledev,$baudrate $othbootargs;" \ 955 "tftp $loadaddr $bootfile;" \ 956 "tftp $fdtaddr $fdtfile;" \ 957 "bootm $loadaddr - $fdtaddr\0" \ 958 "boot_hd = " \ 959 "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ 960 "console=$consoledev,$baudrate $othbootargs;" \ 961 "usb start;" \ 962 "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ 963 "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ 964 "bootm $loadaddr - $fdtaddr\0" \ 965 "boot_usb_fat = " \ 966 "setenv bootargs root=/dev/ram rw " \ 967 "console=$consoledev,$baudrate $othbootargs " \ 968 "ramdisk_size=$ramdisk_size;" \ 969 "usb start;" \ 970 "fatload usb 0:2 $loadaddr $bootfile;" \ 971 "fatload usb 0:2 $fdtaddr $fdtfile;" \ 972 "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ 973 "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ 974 "boot_usb_ext2 = " \ 975 "setenv bootargs root=/dev/ram rw " \ 976 "console=$consoledev,$baudrate $othbootargs " \ 977 "ramdisk_size=$ramdisk_size;" \ 978 "usb start;" \ 979 "ext2load usb 0:4 $loadaddr $bootfile;" \ 980 "ext2load usb 0:4 $fdtaddr $fdtfile;" \ 981 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ 982 "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ 983 "boot_nor = " \ 984 "setenv bootargs root=/dev/$jffs2nor rw " \ 985 "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ 986 "bootm $norbootaddr - $norfdtaddr\0 " \ 987 "boot_ram = " \ 988 "setenv bootargs root=/dev/ram rw " \ 989 "console=$consoledev,$baudrate $othbootargs " \ 990 "ramdisk_size=$ramdisk_size;" \ 991 "tftp $ramdiskaddr $ramdiskfile;" \ 992 "tftp $loadaddr $bootfile;" \ 993 "tftp $fdtaddr $fdtfile;" \ 994 "bootm $loadaddr $ramdiskaddr $fdtaddr\0" 995 996 #endif 997 #endif 998 999 #endif /* __CONFIG_H */ 1000