1 /* 2 * Copyright 2007 Freescale Semiconductor, Inc. 3 * 4 * This program is free software; you can redistribute it and/or 5 * modify it under the terms of the GNU General Public License 6 * Version 2 as published by the Free Software Foundation. 7 */ 8 9 /* 10 * MPC8610HPCD board configuration file 11 * 12 */ 13 14 #ifndef __CONFIG_H 15 #define __CONFIG_H 16 17 /* High Level Configuration Options */ 18 #define CONFIG_MPC86xx 1 /* MPC86xx */ 19 #define CONFIG_MPC8610 1 /* MPC8610 specific */ 20 #define CONFIG_MPC8610HPCD 1 /* MPC8610HPCD board specific */ 21 #define CONFIG_NUM_CPUS 1 /* Number of CPUs in the system */ 22 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ 23 24 #define CONFIG_FSL_DIU_FB 1 /* FSL DIU */ 25 26 /* video */ 27 #undef CONFIG_VIDEO 28 29 #if defined(CONFIG_VIDEO) 30 #define CONFIG_CFB_CONSOLE 31 #define CONFIG_VGA_AS_SINGLE_DEVICE 32 #endif 33 34 #ifdef RUN_DIAG 35 #define CFG_DIAG_ADDR 0xff800000 36 #endif 37 38 #define CFG_RESET_ADDRESS 0xfff00100 39 40 #define CONFIG_PCI 1 /* Enable PCI/PCIE*/ 41 #define CONFIG_PCI1 1 /* PCI controler 1 */ 42 #define CONFIG_PCIE1 1 /* PCIe 1 connected to ULI bridge */ 43 #define CONFIG_PCIE2 1 /* PCIe 2 connected to slot */ 44 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 45 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 46 47 #define CONFIG_ENV_OVERWRITE 48 49 #define CONFIG_SPD_EEPROM /* Use SPD for DDR */ 50 #undef CONFIG_DDR_DLL /* possible DLL fix needed */ 51 #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ 52 #undef CONFIG_DDR_ECC /* only for ECC DDR module */ 53 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 54 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 55 #define CONFIG_NUM_DDR_CONTROLLERS 1 56 #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ 57 58 #define CONFIG_HIGH_BATS 1 /* High BATs supported & enabled */ 59 #define CONFIG_ALTIVEC 1 60 61 /* 62 * L2CR setup -- make sure this is right for your board! 63 */ 64 #define CFG_L2 65 #define L2_INIT 0 66 #define L2_ENABLE (L2CR_L2E |0x00100000 ) 67 68 #ifndef CONFIG_SYS_CLK_FREQ 69 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 70 #endif 71 72 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ 73 #define CONFIG_MISC_INIT_R 1 74 75 #undef CFG_DRAM_TEST /* memory test, takes time */ 76 #define CFG_MEMTEST_START 0x00200000 /* memtest region */ 77 #define CFG_MEMTEST_END 0x00400000 78 #define CFG_ALT_MEMTEST 79 80 /* 81 * Base addresses -- Note these are effective addresses where the 82 * actual resources get mapped (not physical addresses) 83 */ 84 #define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 85 #define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ 86 #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ 87 88 #define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000) 89 #define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000) 90 #define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000) 91 92 #define CFG_DIU_ADDR (CFG_CCSRBAR+0x2c000) 93 94 /* 95 * DDR Setup 96 */ 97 #define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 98 #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE 99 #define CONFIG_VERY_BIG_RAM 100 101 #define MPC86xx_DDR_SDRAM_CLK_CNTL 102 103 #if defined(CONFIG_SPD_EEPROM) 104 /* 105 * Determine DDR configuration from I2C interface. 106 */ 107 #define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */ 108 #else 109 /* 110 * Manually set up DDR1 parameters 111 */ 112 113 #define CFG_SDRAM_SIZE 256 /* DDR is 256MB */ 114 115 #if 0 /* TODO */ 116 #define CFG_DDR_CS0_BNDS 0x0000000F 117 #define CFG_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */ 118 #define CFG_DDR_TIMING_3 0x00000000 119 #define CFG_DDR_TIMING_0 0x00260802 120 #define CFG_DDR_TIMING_1 0x3935d322 121 #define CFG_DDR_TIMING_2 0x14904cc8 122 #define CFG_DDR_MODE_1 0x00480432 123 #define CFG_DDR_MODE_2 0x00000000 124 #define CFG_DDR_INTERVAL 0x06180100 125 #define CFG_DDR_DATA_INIT 0xdeadbeef 126 #define CFG_DDR_CLK_CTRL 0x03800000 127 #define CFG_DDR_OCD_CTRL 0x00000000 128 #define CFG_DDR_OCD_STATUS 0x00000000 129 #define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ 130 #define CFG_DDR_CONTROL2 0x04400010 131 132 #define CFG_DDR_ERR_INT_EN 0x00000000 133 #define CFG_DDR_ERR_DIS 0x00000000 134 #define CFG_DDR_SBE 0x000f0000 135 /* Not used in fixed_sdram function */ 136 #define CFG_DDR_MODE 0x00000022 137 #define CFG_DDR_CS1_BNDS 0x00000000 138 #define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */ 139 #define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */ 140 #define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */ 141 #define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */ 142 #endif 143 #endif 144 145 #define CFG_ID_EEPROM 146 #ifdef CFG_ID_EEPROM 147 #define CONFIG_ID_EEPROM 148 #endif 149 #define ID_EEPROM_ADDR 0x57 150 151 152 #define CFG_FLASH_BASE 0xf0000000 /* start of FLASH 128M */ 153 #define CFG_FLASH_BASE2 0xf8000000 154 155 #define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2} 156 157 #define CFG_BR0_PRELIM 0xf8001001 /* port size 16bit */ 158 #define CFG_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/ 159 160 #define CFG_BR1_PRELIM 0xf0001001 /* port size 16bit */ 161 #define CFG_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */ 162 #if 0 /* TODO */ 163 #define CFG_BR2_PRELIM 0xf0000000 164 #define CFG_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */ 165 #endif 166 #define CFG_BR3_PRELIM 0xe8000801 /* port size 8bit */ 167 #define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ 168 169 170 #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ 171 #define PIXIS_BASE 0xe8000000 /* PIXIS registers */ 172 #define PIXIS_ID 0x0 /* Board ID at offset 0 */ 173 #define PIXIS_VER 0x1 /* Board version at offset 1 */ 174 #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ 175 #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ 176 #define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch */ 177 #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ 178 #define PIXIS_BRDCFG0 0x8 /* PIXIS Board Configuration Register0*/ 179 #define PIXIS_VCTL 0x10 /* VELA Control Register */ 180 #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ 181 #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ 182 #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ 183 #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ 184 #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ 185 #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ 186 #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ 187 #define CFG_PIXIS_VBOOT_MASK 0x0C /* Reset altbank mask*/ 188 189 #define CFG_MAX_FLASH_BANKS 2 /* number of banks */ 190 #define CFG_MAX_FLASH_SECT 1024 /* sectors per device */ 191 192 #undef CFG_FLASH_CHECKSUM 193 #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 194 #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 195 #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ 196 197 #define CFG_FLASH_CFI_DRIVER 198 #define CFG_FLASH_CFI 199 #define CFG_FLASH_EMPTY_INFO 200 201 #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) 202 #define CFG_RAMBOOT 203 #else 204 #undef CFG_RAMBOOT 205 #endif 206 207 #if defined(CFG_RAMBOOT) 208 #undef CONFIG_SPD_EEPROM 209 #define CFG_SDRAM_SIZE 256 210 #endif 211 212 #undef CONFIG_CLOCKS_IN_MHZ 213 214 #define CONFIG_L1_INIT_RAM 215 #define CFG_INIT_RAM_LOCK 1 216 #ifndef CFG_INIT_RAM_LOCK 217 #define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 218 #else 219 #define CFG_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */ 220 #endif 221 #define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ 222 223 #define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ 224 #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) 225 #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET 226 227 #define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 228 #define CFG_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */ 229 230 /* Serial Port */ 231 #define CONFIG_CONS_INDEX 1 232 #undef CONFIG_SERIAL_SOFTWARE_FIFO 233 #define CFG_NS16550 234 #define CFG_NS16550_SERIAL 235 #define CFG_NS16550_REG_SIZE 1 236 #define CFG_NS16550_CLK get_bus_freq(0) 237 238 #define CFG_BAUDRATE_TABLE \ 239 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 240 241 #define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) 242 #define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) 243 244 /* Use the HUSH parser */ 245 #define CFG_HUSH_PARSER 246 #ifdef CFG_HUSH_PARSER 247 #define CFG_PROMPT_HUSH_PS2 "> " 248 #endif 249 250 /* 251 * Pass open firmware flat tree to kernel 252 */ 253 #define CONFIG_OF_LIBFDT 1 254 #define CONFIG_OF_BOARD_SETUP 1 255 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 256 257 258 /* maximum size of the flat tree (8K) */ 259 #define OF_FLAT_TREE_MAX_SIZE 8192 260 261 #define CFG_64BIT_VSPRINTF 1 262 #define CFG_64BIT_STRTOUL 1 263 264 /* 265 * I2C 266 */ 267 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ 268 #define CONFIG_HARD_I2C /* I2C with hardware support*/ 269 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 270 #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ 271 #define CFG_I2C_SLAVE 0x7F 272 #define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ 273 #define CFG_I2C_OFFSET 0x3000 274 275 /* 276 * General PCI 277 * Addresses are mapped 1-1. 278 */ 279 #define CFG_PCI1_MEM_BASE 0x80000000 280 #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE 281 #define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */ 282 #define CFG_PCI1_IO_BASE 0x00000000 283 #define CFG_PCI1_IO_PHYS 0xe1000000 284 #define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */ 285 286 /* PCI view of System Memory */ 287 #define CFG_PCI_MEMORY_BUS 0x00000000 288 #define CFG_PCI_MEMORY_PHYS 0x00000000 289 #define CFG_PCI_MEMORY_SIZE 0x80000000 290 291 /* For RTL8139 */ 292 #define KSEG1ADDR(x) ({u32 _x = le32_to_cpu(*(u32 *)(x)); (&_x); }) 293 #define _IO_BASE 0x00000000 294 295 /* controller 1, Base address 0xa000 */ 296 #define CFG_PCIE1_MEM_BASE 0xa0000000 297 #define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE 298 #define CFG_PCIE1_MEM_SIZE 0x10000000 /* 256M */ 299 #define CFG_PCIE1_IO_BASE 0x00000000 300 #define CFG_PCIE1_IO_PHYS 0xe3000000 301 #define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */ 302 303 /* controller 2, Base Address 0x9000 */ 304 #define CFG_PCIE2_MEM_BASE 0x90000000 305 #define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE 306 #define CFG_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 307 #define CFG_PCIE2_IO_BASE 0x00000000 /* reuse mem LAW */ 308 #define CFG_PCIE2_IO_PHYS 0xe2000000 309 #define CFG_PCIE2_IO_SIZE 0x00100000 /* 1M */ 310 311 312 #if defined(CONFIG_PCI) 313 314 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 315 316 #define CONFIG_NET_MULTI 317 #define CONFIG_CMD_NET 318 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 319 #define CONFIG_CMD_REGINFO 320 321 #define CONFIG_ULI526X 322 #ifdef CONFIG_ULI526X 323 #define CONFIG_ETHADDR 00:E0:0C:00:00:01 324 #endif 325 326 /************************************************************ 327 * USB support 328 ************************************************************/ 329 #define CONFIG_PCI_OHCI 1 330 #define CONFIG_USB_OHCI_NEW 1 331 #define CONFIG_USB_KEYBOARD 1 332 #define CFG_DEVICE_DEREGISTER 333 #define CFG_USB_EVENT_POLL 1 334 #define CFG_USB_OHCI_SLOT_NAME "ohci_pci" 335 #define CFG_USB_OHCI_MAX_ROOT_PORTS 15 336 #define CFG_OHCI_SWAP_REG_ACCESS 1 337 338 #if !defined(CONFIG_PCI_PNP) 339 #define PCI_ENET0_IOADDR 0xe0000000 340 #define PCI_ENET0_MEMADDR 0xe0000000 341 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ 342 #endif 343 344 #define CONFIG_DOS_PARTITION 345 #define CONFIG_SCSI_AHCI 346 347 #ifdef CONFIG_SCSI_AHCI 348 #define CONFIG_SATA_ULI5288 349 #define CFG_SCSI_MAX_SCSI_ID 4 350 #define CFG_SCSI_MAX_LUN 1 351 #define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN) 352 #define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE 353 #endif 354 355 #endif /* CONFIG_PCI */ 356 357 /* 358 * BAT0 2G Cacheable, non-guarded 359 * 0x0000_0000 2G DDR 360 */ 361 #define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 362 #define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) 363 #define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE ) 364 #define CFG_IBAT0U CFG_DBAT0U 365 366 /* 367 * BAT1 1G Cache-inhibited, guarded 368 * 0x8000_0000 256M PCI-1 Memory 369 * 0xa000_0000 256M PCI-Express 1 Memory 370 * 0x9000_0000 256M PCI-Express 2 Memory 371 */ 372 373 #define CFG_DBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ 374 | BATL_GUARDEDSTORAGE) 375 #define CFG_DBAT1U (CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP) 376 #define CFG_IBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) 377 #define CFG_IBAT1U CFG_DBAT1U 378 379 /* 380 * BAT2 16M Cache-inhibited, guarded 381 * 0xe100_0000 1M PCI-1 I/O 382 */ 383 384 #define CFG_DBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ 385 | BATL_GUARDEDSTORAGE) 386 #define CFG_DBAT2U (CFG_PCI1_IO_PHYS | BATU_BL_16M | BATU_VS | BATU_VP) 387 #define CFG_IBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) 388 #define CFG_IBAT2U CFG_DBAT2U 389 390 /* 391 * BAT3 32M Cache-inhibited, guarded 392 * 0xe200_0000 1M PCI-Express 2 I/O 393 * 0xe300_0000 1M PCI-Express 1 I/O 394 */ 395 396 #define CFG_DBAT3L (CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ 397 | BATL_GUARDEDSTORAGE) 398 #define CFG_DBAT3U (CFG_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP) 399 #define CFG_IBAT3L (CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) 400 #define CFG_IBAT3U CFG_DBAT3U 401 402 /* 403 * BAT4 4M Cache-inhibited, guarded 404 * 0xe000_0000 4M CCSR 405 */ 406 #define CFG_DBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \ 407 | BATL_GUARDEDSTORAGE) 408 #define CFG_DBAT4U (CFG_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP) 409 #define CFG_IBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) 410 #define CFG_IBAT4U CFG_DBAT4U 411 412 /* 413 * BAT5 128K Cacheable, non-guarded 414 * 0xe400_0000 128K Init RAM for stack in the CPU DCache (no backing memory) 415 */ 416 #define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) 417 #define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 418 #define CFG_IBAT5L CFG_DBAT5L 419 #define CFG_IBAT5U CFG_DBAT5U 420 421 /* 422 * BAT6 256M Cache-inhibited, guarded 423 * 0xf000_0000 256M FLASH 424 */ 425 #define CFG_DBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \ 426 | BATL_GUARDEDSTORAGE) 427 #define CFG_DBAT6U (CFG_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP) 428 #define CFG_IBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE) 429 #define CFG_IBAT6U CFG_DBAT6U 430 431 /* 432 * BAT7 4M Cache-inhibited, guarded 433 * 0xe800_0000 4M PIXIS 434 */ 435 #define CFG_DBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \ 436 | BATL_GUARDEDSTORAGE) 437 #define CFG_DBAT7U (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP) 438 #define CFG_IBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) 439 #define CFG_IBAT7U CFG_DBAT7U 440 441 442 /* 443 * Environment 444 */ 445 #ifndef CFG_RAMBOOT 446 #define CFG_ENV_IS_IN_FLASH 1 447 #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) 448 #define CFG_ENV_SECT_SIZE 0x20000 /* 126k (one sector) for env */ 449 #define CFG_ENV_SIZE 0x2000 450 #else 451 #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 452 #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) 453 #define CFG_ENV_SIZE 0x2000 454 #endif 455 456 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 457 #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 458 459 460 /* 461 * BOOTP options 462 */ 463 #define CONFIG_BOOTP_BOOTFILESIZE 464 #define CONFIG_BOOTP_BOOTPATH 465 #define CONFIG_BOOTP_GATEWAY 466 #define CONFIG_BOOTP_HOSTNAME 467 468 469 /* 470 * Command line configuration. 471 */ 472 #include <config_cmd_default.h> 473 474 #define CONFIG_CMD_PING 475 #define CONFIG_CMD_I2C 476 #define CONFIG_CMD_MII 477 478 #if defined(CFG_RAMBOOT) 479 #undef CONFIG_CMD_ENV 480 #endif 481 482 #if defined(CONFIG_PCI) 483 #define CONFIG_CMD_PCI 484 #define CONFIG_CMD_SCSI 485 #define CONFIG_CMD_EXT2 486 #define CONFIG_CMD_USB 487 #endif 488 489 490 #undef CONFIG_WATCHDOG /* watchdog disabled */ 491 492 /*DIU Configuration*/ 493 #define DIU_CONNECT_TO_DVI /* DIU controller connects to DVI encoder*/ 494 495 /* 496 * Miscellaneous configurable options 497 */ 498 #define CFG_LONGHELP /* undef to save memory */ 499 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 500 #define CFG_LOAD_ADDR 0x2000000 /* default load address */ 501 #define CFG_PROMPT "=> " /* Monitor Command Prompt */ 502 503 #if defined(CONFIG_CMD_KGDB) 504 #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ 505 #else 506 #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ 507 #endif 508 509 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ 510 #define CFG_MAXARGS 16 /* max number of command args */ 511 #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ 512 #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ 513 514 /* 515 * For booting Linux, the board info and command line data 516 * have to be in the first 8 MB of memory, since this is 517 * the maximum mapped by the Linux kernel during initialization. 518 */ 519 #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ 520 521 /* 522 * Internal Definitions 523 * 524 * Boot Flags 525 */ 526 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 527 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 528 529 #if defined(CONFIG_CMD_KGDB) 530 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 531 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 532 #endif 533 534 /* 535 * Environment Configuration 536 */ 537 #define CONFIG_IPADDR 192.168.1.100 538 539 #define CONFIG_HOSTNAME unknown 540 #define CONFIG_ROOTPATH /opt/nfsroot 541 #define CONFIG_BOOTFILE uImage 542 #define CONFIG_UBOOTPATH 8610hpcd/u-boot.bin 543 544 #define CONFIG_SERVERIP 192.168.1.1 545 #define CONFIG_GATEWAYIP 192.168.1.1 546 #define CONFIG_NETMASK 255.255.255.0 547 548 /* default location for tftp and bootm */ 549 #define CONFIG_LOADADDR 1000000 550 551 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 552 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 553 554 #define CONFIG_BAUDRATE 115200 555 556 #if defined(CONFIG_PCI1) 557 #define PCI_ENV \ 558 "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \ 559 "echo e;md ${a}e00 9\0" \ 560 "pci1regs=setenv a e0008; run pcireg\0" \ 561 "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \ 562 "pci d.w $b.0 56 1\0" \ 563 "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \ 564 "pci w.w $b.0 56 ffff\0" \ 565 "pci1err=setenv a e0008; run pcierr\0" \ 566 "pci1errc=setenv a e0008; run pcierrc\0" 567 #else 568 #define PCI_ENV "" 569 #endif 570 571 #if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) 572 #define PCIE_ENV \ 573 "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \ 574 "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \ 575 "pcie1regs=setenv a e000a; run pciereg\0" \ 576 "pcie2regs=setenv a e0009; run pciereg\0" \ 577 "pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\ 578 "pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;" \ 579 "pci d $b.0 130 1\0" \ 580 "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\ 581 "pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \ 582 "pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0" \ 583 "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \ 584 "pcie1err=setenv a e000a; run pcieerr\0" \ 585 "pcie2err=setenv a e0009; run pcieerr\0" \ 586 "pcie1errc=setenv a e000a; run pcieerrc\0" \ 587 "pcie2errc=setenv a e0009; run pcieerrc\0" 588 #else 589 #define PCIE_ENV "" 590 #endif 591 592 #define DMA_ENV \ 593 "dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\ 594 "mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \ 595 "dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\ 596 "mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \ 597 "dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\ 598 "mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \ 599 "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\ 600 "mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0" 601 602 #ifdef ENV_DEBUG 603 #define CONFIG_EXTRA_ENV_SETTINGS \ 604 "netdev=eth0\0" \ 605 "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ 606 "tftpflash=tftpboot $loadaddr $uboot; " \ 607 "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ 608 "erase " MK_STR(TEXT_BASE) " +$filesize; " \ 609 "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ 610 "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ 611 "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ 612 "consoledev=ttyS0\0" \ 613 "ramdiskaddr=2000000\0" \ 614 "ramdiskfile=8610hpcd/ramdisk.uboot\0" \ 615 "fdtaddr=c00000\0" \ 616 "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \ 617 "bdev=sda3\0" \ 618 "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ 619 "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ 620 "maxcpus=1" \ 621 "eoi=mw e00400b0 0\0" \ 622 "iack=md e00400a0 1\0" \ 623 "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \ 624 "md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \ 625 "md ${a}f00 5\0" \ 626 "ddr1regs=setenv a e0002; run ddrreg\0" \ 627 "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \ 628 "md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \ 629 "md ${a}e60 1; md ${a}ef0 1d\0" \ 630 "guregs=setenv a e00e0; run gureg\0" \ 631 "mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \ 632 "mcmregs=setenv a e0001; run mcmreg\0" \ 633 "diuregs=md e002c000 1d\0" \ 634 "dium=mw e002c01c\0" \ 635 "diuerr=md e002c014 1\0" \ 636 "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 debug\0" \ 637 "monitor=0-DVI\0" \ 638 "pmregs=md e00e1000 2b\0" \ 639 "lawregs=md e0000c08 4b\0" \ 640 "lbcregs=md e0005000 36\0" \ 641 "dma0regs=md e0021100 12\0" \ 642 "dma1regs=md e0021180 12\0" \ 643 "dma2regs=md e0021200 12\0" \ 644 "dma3regs=md e0021280 12\0" \ 645 PCI_ENV \ 646 PCIE_ENV \ 647 DMA_ENV 648 #else 649 #define CONFIG_EXTRA_ENV_SETTINGS \ 650 "netdev=eth0\0" \ 651 "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ 652 "consoledev=ttyS0\0" \ 653 "ramdiskaddr=2000000\0" \ 654 "ramdiskfile=8610hpcd/ramdisk.uboot\0" \ 655 "fdtaddr=c00000\0" \ 656 "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \ 657 "bdev=sda3\0" \ 658 "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0\0"\ 659 "monitor=0-DVI\0" 660 #endif 661 662 #define CONFIG_NFSBOOTCOMMAND \ 663 "setenv bootargs root=/dev/nfs rw " \ 664 "nfsroot=$serverip:$rootpath " \ 665 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 666 "console=$consoledev,$baudrate $othbootargs;" \ 667 "tftp $loadaddr $bootfile;" \ 668 "tftp $fdtaddr $fdtfile;" \ 669 "bootm $loadaddr - $fdtaddr" 670 671 #define CONFIG_RAMBOOTCOMMAND \ 672 "setenv bootargs root=/dev/ram rw " \ 673 "console=$consoledev,$baudrate $othbootargs;" \ 674 "tftp $ramdiskaddr $ramdiskfile;" \ 675 "tftp $loadaddr $bootfile;" \ 676 "tftp $fdtaddr $fdtfile;" \ 677 "bootm $loadaddr $ramdiskaddr $fdtaddr" 678 679 #define CONFIG_BOOTCOMMAND \ 680 "setenv bootargs root=/dev/$bdev rw " \ 681 "console=$consoledev,$baudrate $othbootargs;" \ 682 "tftp $loadaddr $bootfile;" \ 683 "tftp $fdtaddr $fdtfile;" \ 684 "bootm $loadaddr - $fdtaddr" 685 686 #endif /* __CONFIG_H */ 687