1 /* 2 * Copyright 2009-2011 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * mpc8569mds board configuration file 9 */ 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 #define CONFIG_FSL_ELBC 1 /* Has Enhance localbus controller */ 14 15 #define CONFIG_SYS_SRIO 16 #define CONFIG_SRIO1 /* SRIO port 1 */ 17 18 #define CONFIG_PCIE1 1 /* PCIE controller */ 19 #define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */ 20 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 21 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 22 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 23 #define CONFIG_QE /* Enable QE */ 24 #define CONFIG_ENV_OVERWRITE 25 26 #ifndef __ASSEMBLY__ 27 extern unsigned long get_clock_freq(void); 28 #endif 29 /* Replace a call to get_clock_freq (after it is implemented)*/ 30 #define CONFIG_SYS_CLK_FREQ 66666666 31 #define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ 32 33 #ifdef CONFIG_ATM 34 #define CONFIG_PQ_MDS_PIB 35 #define CONFIG_PQ_MDS_PIB_ATM 36 #endif 37 38 /* 39 * These can be toggled for performance analysis, otherwise use default. 40 */ 41 #define CONFIG_L2_CACHE /* toggle L2 cache */ 42 #define CONFIG_BTB /* toggle branch predition */ 43 44 #ifndef CONFIG_SYS_TEXT_BASE 45 #define CONFIG_SYS_TEXT_BASE 0xfff80000 46 #endif 47 48 #ifndef CONFIG_SYS_MONITOR_BASE 49 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 50 #endif 51 52 /* 53 * Only possible on E500 Version 2 or newer cores. 54 */ 55 #define CONFIG_ENABLE_36BIT_PHYS 1 56 57 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ 58 #define CONFIG_BOARD_EARLY_INIT_R 1 59 #define CONFIG_HWCONFIG 60 61 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 62 #define CONFIG_SYS_MEMTEST_END 0x00400000 63 64 /* 65 * Config the L2 Cache as L2 SRAM 66 */ 67 #define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 68 #define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR 69 #define CONFIG_SYS_L2_SIZE (512 << 10) 70 #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) 71 72 #define CONFIG_SYS_CCSRBAR 0xe0000000 73 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 74 75 #if defined(CONFIG_NAND_SPL) 76 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 77 #endif 78 79 /* DDR Setup */ 80 #define CONFIG_SYS_FSL_DDR3 81 #undef CONFIG_FSL_DDR_INTERACTIVE 82 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 83 #define CONFIG_DDR_SPD 84 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 85 86 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 87 88 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 89 /* DDR is system memory*/ 90 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 91 92 #define CONFIG_NUM_DDR_CONTROLLERS 1 93 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 94 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 95 96 /* I2C addresses of SPD EEPROMs */ 97 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 98 99 /* These are used when DDR doesn't use SPD. */ 100 #define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1024MB */ 101 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F 102 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 103 #define CONFIG_SYS_DDR_TIMING_3 0x00020000 104 #define CONFIG_SYS_DDR_TIMING_0 0x00330004 105 #define CONFIG_SYS_DDR_TIMING_1 0x6F6B4644 106 #define CONFIG_SYS_DDR_TIMING_2 0x002888D0 107 #define CONFIG_SYS_DDR_SDRAM_CFG 0x47000000 108 #define CONFIG_SYS_DDR_SDRAM_CFG_2 0x04401040 109 #define CONFIG_SYS_DDR_SDRAM_MODE 0x40401521 110 #define CONFIG_SYS_DDR_SDRAM_MODE_2 0x8000C000 111 #define CONFIG_SYS_DDR_SDRAM_INTERVAL 0x03E00000 112 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 113 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x01000000 114 #define CONFIG_SYS_DDR_TIMING_4 0x00220001 115 #define CONFIG_SYS_DDR_TIMING_5 0x03402400 116 #define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600 117 #define CONFIG_SYS_DDR_WRLVL_CNTL 0x0655A604 118 #define CONFIG_SYS_DDR_CDR_1 0x80040000 119 #define CONFIG_SYS_DDR_CDR_2 0x00000000 120 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 121 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 122 #define CONFIG_SYS_DDR_CONTROL 0xc7000000 /* Type = DDR3 */ 123 #define CONFIG_SYS_DDR_CONTROL2 0x24400000 124 125 #define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d 126 #define CONFIG_SYS_DDR_ERR_DIS 0x00000000 127 #define CONFIG_SYS_DDR_SBE 0x00010000 128 129 #undef CONFIG_CLOCKS_IN_MHZ 130 131 /* 132 * Local Bus Definitions 133 */ 134 135 #define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ 136 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 137 138 #define CONFIG_SYS_BCSR_BASE 0xf8000000 139 #define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE 140 141 /*Chip select 0 - Flash*/ 142 #define CONFIG_FLASH_BR_PRELIM 0xfe000801 143 #define CONFIG_FLASH_OR_PRELIM 0xfe000ff7 144 145 /*Chip select 1 - BCSR*/ 146 #define CONFIG_SYS_BR1_PRELIM 0xf8000801 147 #define CONFIG_SYS_OR1_PRELIM 0xffffe9f7 148 149 /*Chip select 4 - PIB*/ 150 #define CONFIG_SYS_BR4_PRELIM 0xf8008801 151 #define CONFIG_SYS_OR4_PRELIM 0xffffe9f7 152 153 /*Chip select 5 - PIB*/ 154 #define CONFIG_SYS_BR5_PRELIM 0xf8010801 155 #define CONFIG_SYS_OR5_PRELIM 0xffffe9f7 156 157 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 158 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ 159 #undef CONFIG_SYS_FLASH_CHECKSUM 160 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 161 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 162 163 #undef CONFIG_SYS_RAMBOOT 164 165 #define CONFIG_FLASH_CFI_DRIVER 166 #define CONFIG_SYS_FLASH_CFI 167 #define CONFIG_SYS_FLASH_EMPTY_INFO 168 169 /* Chip select 3 - NAND */ 170 #ifndef CONFIG_NAND_SPL 171 #define CONFIG_SYS_NAND_BASE 0xFC000000 172 #else 173 #define CONFIG_SYS_NAND_BASE 0xFFF00000 174 #endif 175 176 /* NAND boot: 4K NAND loader config */ 177 #define CONFIG_SYS_NAND_SPL_SIZE 0x1000 178 #define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000) 179 #define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR) 180 #define CONFIG_SYS_NAND_U_BOOT_START \ 181 (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE) 182 #define CONFIG_SYS_NAND_U_BOOT_OFFS (0) 183 #define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000) 184 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) 185 186 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 187 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, } 188 #define CONFIG_SYS_MAX_NAND_DEVICE 1 189 #define CONFIG_CMD_NAND 1 190 #define CONFIG_NAND_FSL_ELBC 1 191 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 192 #define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ 193 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 194 | BR_PS_8 /* Port Size = 8 bit */ \ 195 | BR_MS_FCM /* MSEL = FCM */ \ 196 | BR_V) /* valid */ 197 #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ 198 | OR_FCM_CSCT \ 199 | OR_FCM_CST \ 200 | OR_FCM_CHT \ 201 | OR_FCM_SCY_1 \ 202 | OR_FCM_TRLX \ 203 | OR_FCM_EHTR) 204 205 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 206 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 207 #define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 208 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 209 210 #define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */ 211 #define CONFIG_SYS_LBC_LBCR 0x00040000 /* LB config reg */ 212 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 213 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 214 215 #define CONFIG_SYS_INIT_RAM_LOCK 1 216 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 217 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 218 219 #define CONFIG_SYS_GBL_DATA_OFFSET \ 220 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 221 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 222 223 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 224 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 225 226 /* Serial Port */ 227 #define CONFIG_CONS_INDEX 1 228 #define CONFIG_SYS_NS16550_SERIAL 229 #define CONFIG_SYS_NS16550_REG_SIZE 1 230 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 231 #ifdef CONFIG_NAND_SPL 232 #define CONFIG_NS16550_MIN_FUNCTIONS 233 #endif 234 235 #define CONFIG_SYS_BAUDRATE_TABLE \ 236 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 237 238 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 239 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 240 241 /* 242 * I2C 243 */ 244 #define CONFIG_SYS_I2C 245 #define CONFIG_SYS_I2C_FSL 246 #define CONFIG_SYS_FSL_I2C_SPEED 400000 247 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 248 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 249 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 250 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 251 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 252 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 253 254 /* 255 * I2C2 EEPROM 256 */ 257 #define CONFIG_ID_EEPROM 258 #ifdef CONFIG_ID_EEPROM 259 #define CONFIG_SYS_I2C_EEPROM_NXID 260 #endif 261 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 262 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 263 #define CONFIG_SYS_EEPROM_BUS_NUM 1 264 265 #define PLPPAR1_I2C_BIT_MASK 0x0000000F 266 #define PLPPAR1_I2C2_VAL 0x00000000 267 #define PLPPAR1_ESDHC_VAL 0x0000000A 268 #define PLPDIR1_I2C_BIT_MASK 0x0000000F 269 #define PLPDIR1_I2C2_VAL 0x0000000F 270 #define PLPDIR1_ESDHC_VAL 0x00000006 271 #define PLPPAR1_UART0_BIT_MASK 0x00000fc0 272 #define PLPPAR1_ESDHC_4BITS_VAL 0x00000a80 273 #define PLPDIR1_UART0_BIT_MASK 0x00000fc0 274 #define PLPDIR1_ESDHC_4BITS_VAL 0x00000a80 275 276 /* 277 * General PCI 278 * Memory Addresses are mapped 1-1. I/O is mapped from 0 279 */ 280 #define CONFIG_SYS_PCIE1_NAME "Slot" 281 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 282 #define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 283 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 284 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 285 #define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000 286 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 287 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000 288 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 289 290 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xC0000000 291 #define CONFIG_SYS_SRIO1_MEM_BUS 0xC0000000 292 #define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BUS 293 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */ 294 295 #ifdef CONFIG_QE 296 /* 297 * QE UEC ethernet configuration 298 */ 299 #define CONFIG_SYS_UCC_RGMII_MODE /* Set UCC work at RGMII by default */ 300 #undef CONFIG_SYS_UCC_RMII_MODE /* Set UCC work at RMII mode */ 301 302 #define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120) 303 #define CONFIG_UEC_ETH 304 #define CONFIG_ETHPRIME "UEC0" 305 #define CONFIG_PHY_MODE_NEED_CHANGE 306 307 #define CONFIG_UEC_ETH1 /* GETH1 */ 308 #define CONFIG_HAS_ETH0 309 310 #ifdef CONFIG_UEC_ETH1 311 #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ 312 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE 313 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 314 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK12 315 #define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH 316 #define CONFIG_SYS_UEC1_PHY_ADDR 7 317 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 318 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000 319 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 320 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK16 /* CLK16 for RMII */ 321 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH 322 #define CONFIG_SYS_UEC1_PHY_ADDR 8 /* 0x8 for RMII */ 323 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 324 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 325 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 326 #endif /* CONFIG_UEC_ETH1 */ 327 328 #define CONFIG_UEC_ETH2 /* GETH2 */ 329 #define CONFIG_HAS_ETH1 330 331 #ifdef CONFIG_UEC_ETH2 332 #define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ 333 #define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE 334 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 335 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK17 336 #define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH 337 #define CONFIG_SYS_UEC2_PHY_ADDR 1 338 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 339 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000 340 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 341 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK16 /* CLK 16 for RMII */ 342 #define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH 343 #define CONFIG_SYS_UEC2_PHY_ADDR 0x9 /* 0x9 for RMII */ 344 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 345 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 346 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 347 #endif /* CONFIG_UEC_ETH2 */ 348 349 #define CONFIG_UEC_ETH3 /* GETH3 */ 350 #define CONFIG_HAS_ETH2 351 352 #ifdef CONFIG_UEC_ETH3 353 #define CONFIG_SYS_UEC3_UCC_NUM 2 /* UCC3 */ 354 #define CONFIG_SYS_UEC3_RX_CLK QE_CLK_NONE 355 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 356 #define CONFIG_SYS_UEC3_TX_CLK QE_CLK12 357 #define CONFIG_SYS_UEC3_ETH_TYPE GIGA_ETH 358 #define CONFIG_SYS_UEC3_PHY_ADDR 2 359 #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 360 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 1000 361 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 362 #define CONFIG_SYS_UEC3_TX_CLK QE_CLK16 /* CLK_16 for RMII */ 363 #define CONFIG_SYS_UEC3_ETH_TYPE FAST_ETH 364 #define CONFIG_SYS_UEC3_PHY_ADDR 0xA /* 0xA for RMII */ 365 #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 366 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 100 367 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 368 #endif /* CONFIG_UEC_ETH3 */ 369 370 #define CONFIG_UEC_ETH4 /* GETH4 */ 371 #define CONFIG_HAS_ETH3 372 373 #ifdef CONFIG_UEC_ETH4 374 #define CONFIG_SYS_UEC4_UCC_NUM 3 /* UCC4 */ 375 #define CONFIG_SYS_UEC4_RX_CLK QE_CLK_NONE 376 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 377 #define CONFIG_SYS_UEC4_TX_CLK QE_CLK17 378 #define CONFIG_SYS_UEC4_ETH_TYPE GIGA_ETH 379 #define CONFIG_SYS_UEC4_PHY_ADDR 3 380 #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 381 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 1000 382 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 383 #define CONFIG_SYS_UEC4_TX_CLK QE_CLK16 /* CLK16 for RMII */ 384 #define CONFIG_SYS_UEC4_ETH_TYPE FAST_ETH 385 #define CONFIG_SYS_UEC4_PHY_ADDR 0xB /* 0xB for RMII */ 386 #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 387 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 100 388 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 389 #endif /* CONFIG_UEC_ETH4 */ 390 391 #undef CONFIG_UEC_ETH6 /* GETH6 */ 392 #define CONFIG_HAS_ETH5 393 394 #ifdef CONFIG_UEC_ETH6 395 #define CONFIG_SYS_UEC6_UCC_NUM 5 /* UCC6 */ 396 #define CONFIG_SYS_UEC6_RX_CLK QE_CLK_NONE 397 #define CONFIG_SYS_UEC6_TX_CLK QE_CLK_NONE 398 #define CONFIG_SYS_UEC6_ETH_TYPE GIGA_ETH 399 #define CONFIG_SYS_UEC6_PHY_ADDR 4 400 #define CONFIG_SYS_UEC6_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII 401 #define CONFIG_SYS_UEC6_INTERFACE_SPEED 1000 402 #endif /* CONFIG_UEC_ETH6 */ 403 404 #undef CONFIG_UEC_ETH8 /* GETH8 */ 405 #define CONFIG_HAS_ETH7 406 407 #ifdef CONFIG_UEC_ETH8 408 #define CONFIG_SYS_UEC8_UCC_NUM 7 /* UCC8 */ 409 #define CONFIG_SYS_UEC8_RX_CLK QE_CLK_NONE 410 #define CONFIG_SYS_UEC8_TX_CLK QE_CLK_NONE 411 #define CONFIG_SYS_UEC8_ETH_TYPE GIGA_ETH 412 #define CONFIG_SYS_UEC8_PHY_ADDR 6 413 #define CONFIG_SYS_UEC8_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII 414 #define CONFIG_SYS_UEC8_INTERFACE_SPEED 1000 415 #endif /* CONFIG_UEC_ETH8 */ 416 417 #endif /* CONFIG_QE */ 418 419 #if defined(CONFIG_PCI) 420 #undef CONFIG_EEPRO100 421 #undef CONFIG_TULIP 422 423 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 424 425 #endif /* CONFIG_PCI */ 426 427 /* 428 * Environment 429 */ 430 #if defined(CONFIG_SYS_RAMBOOT) 431 #else 432 #define CONFIG_ENV_IS_IN_FLASH 1 433 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 434 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 435 #define CONFIG_ENV_SIZE 0x2000 436 #endif 437 438 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 439 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 440 441 /* QE microcode/firmware address */ 442 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 443 #define CONFIG_SYS_QE_FW_ADDR 0xfff00000 444 445 /* 446 * BOOTP options 447 */ 448 #define CONFIG_BOOTP_BOOTFILESIZE 449 #define CONFIG_BOOTP_BOOTPATH 450 #define CONFIG_BOOTP_GATEWAY 451 #define CONFIG_BOOTP_HOSTNAME 452 453 /* 454 * Command line configuration. 455 */ 456 #define CONFIG_CMD_IRQ 457 #define CONFIG_CMD_REGINFO 458 459 #if defined(CONFIG_PCI) 460 #define CONFIG_CMD_PCI 461 #endif 462 463 #undef CONFIG_WATCHDOG /* watchdog disabled */ 464 465 #ifdef CONFIG_MMC 466 #define CONFIG_FSL_ESDHC 467 #define CONFIG_FSL_ESDHC_PIN_MUX 468 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 469 #define CONFIG_GENERIC_MMC 470 #define CONFIG_DOS_PARTITION 471 #endif 472 473 /* 474 * Miscellaneous configurable options 475 */ 476 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 477 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 478 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 479 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 480 #if defined(CONFIG_CMD_KGDB) 481 #define CONFIG_SYS_CBSIZE 2048 /* Console I/O Buffer Size */ 482 #else 483 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 484 #endif 485 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 486 /* Print Buffer Size */ 487 #define CONFIG_SYS_MAXARGS 32 /* max number of command args */ 488 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 489 /* Boot Argument Buffer Size */ 490 491 /* 492 * For booting Linux, the board info and command line data 493 * have to be in the first 64 MB of memory, since this is 494 * the maximum mapped by the Linux kernel during initialization. 495 */ 496 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 497 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 498 499 #if defined(CONFIG_CMD_KGDB) 500 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 501 #endif 502 503 /* 504 * Environment Configuration 505 */ 506 #define CONFIG_HOSTNAME mpc8569mds 507 #define CONFIG_ROOTPATH "/nfsroot" 508 #define CONFIG_BOOTFILE "your.uImage" 509 510 #define CONFIG_SERVERIP 192.168.1.1 511 #define CONFIG_GATEWAYIP 192.168.1.1 512 #define CONFIG_NETMASK 255.255.255.0 513 514 #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ 515 516 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 517 518 #define CONFIG_BAUDRATE 115200 519 520 #define CONFIG_EXTRA_ENV_SETTINGS \ 521 "netdev=eth0\0" \ 522 "consoledev=ttyS0\0" \ 523 "ramdiskaddr=600000\0" \ 524 "ramdiskfile=your.ramdisk.u-boot\0" \ 525 "fdtaddr=400000\0" \ 526 "fdtfile=your.fdt.dtb\0" \ 527 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 528 "nfsroot=$serverip:$rootpath " \ 529 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 530 "console=$consoledev,$baudrate $othbootargs\0" \ 531 "ramargs=setenv bootargs root=/dev/ram rw " \ 532 "console=$consoledev,$baudrate $othbootargs\0" \ 533 534 #define CONFIG_NFSBOOTCOMMAND \ 535 "run nfsargs;" \ 536 "tftp $loadaddr $bootfile;" \ 537 "tftp $fdtaddr $fdtfile;" \ 538 "bootm $loadaddr - $fdtaddr" 539 540 #define CONFIG_RAMBOOTCOMMAND \ 541 "run ramargs;" \ 542 "tftp $ramdiskaddr $ramdiskfile;" \ 543 "tftp $loadaddr $bootfile;" \ 544 "bootm $loadaddr $ramdiskaddr" 545 546 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 547 548 #endif /* __CONFIG_H */ 549