1 /* 2 * Copyright (C) 2009 Freescale Semiconductor, Inc. 3 * 4 * See file CREDITS for list of people who contributed to this 5 * project. 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License as 9 * published by the Free Software Foundation; either version 2 of 10 * the License, or (at your option) any later version. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 20 * MA 02111-1307 USA 21 */ 22 23 /* 24 * mpc8569mds board configuration file 25 */ 26 #ifndef __CONFIG_H 27 #define __CONFIG_H 28 29 /* High Level Configuration Options */ 30 #define CONFIG_BOOKE 1 /* BOOKE */ 31 #define CONFIG_E500 1 /* BOOKE e500 family */ 32 #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/68 */ 33 #define CONFIG_MPC8569 1 /* MPC8569 specific */ 34 #define CONFIG_MPC8569MDS 1 /* MPC8569MDS board specific */ 35 36 #define CONFIG_FSL_ELBC 1 /* Has Enhance localbus controller */ 37 38 #define CONFIG_PCI 1 /* Disable PCI/PCIE */ 39 #define CONFIG_PCIE1 1 /* PCIE controller */ 40 #define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */ 41 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 42 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 43 #define CONFIG_QE /* Enable QE */ 44 #define CONFIG_ENV_OVERWRITE 45 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 46 47 #ifndef __ASSEMBLY__ 48 extern unsigned long get_clock_freq(void); 49 #endif 50 /* Replace a call to get_clock_freq (after it is implemented)*/ 51 #define CONFIG_SYS_CLK_FREQ 66666666 52 #define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ 53 54 /* 55 * These can be toggled for performance analysis, otherwise use default. 56 */ 57 #define CONFIG_L2_CACHE /* toggle L2 cache */ 58 #define CONFIG_BTB /* toggle branch predition */ 59 60 /* 61 * Only possible on E500 Version 2 or newer cores. 62 */ 63 #define CONFIG_ENABLE_36BIT_PHYS 1 64 65 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ 66 #define CONFIG_HWCONFIG 67 68 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 69 #define CONFIG_SYS_MEMTEST_END 0x00400000 70 71 /* 72 * Base addresses -- Note these are effective addresses where the 73 * actual resources get mapped (not physical addresses) 74 */ 75 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 76 #define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ 77 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR 78 /* physical addr of CCSRBAR */ 79 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR 80 /* PQII uses CONFIG_SYS_IMMR */ 81 82 #define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) 83 #define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) 84 85 /* DDR Setup */ 86 #define CONFIG_FSL_DDR3 87 #undef CONFIG_FSL_DDR_INTERACTIVE 88 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 89 #define CONFIG_DDR_SPD 90 #define CONFIG_DDR_DLL /* possible DLL fix needed */ 91 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 92 93 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 94 95 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 96 /* DDR is system memory*/ 97 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 98 99 #define CONFIG_NUM_DDR_CONTROLLERS 1 100 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 101 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 102 103 /* I2C addresses of SPD EEPROMs */ 104 #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ 105 #define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 1 DIMM 0 */ 106 107 /* These are used when DDR doesn't use SPD. */ 108 #define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1024MB */ 109 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F 110 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 111 #define CONFIG_SYS_DDR_TIMING_3 0x00020000 112 #define CONFIG_SYS_DDR_TIMING_0 0x00330004 113 #define CONFIG_SYS_DDR_TIMING_1 0x6F6B4644 114 #define CONFIG_SYS_DDR_TIMING_2 0x002888D0 115 #define CONFIG_SYS_DDR_SDRAM_CFG 0x47000000 116 #define CONFIG_SYS_DDR_SDRAM_CFG_2 0x04401040 117 #define CONFIG_SYS_DDR_SDRAM_MODE 0x40401521 118 #define CONFIG_SYS_DDR_SDRAM_MODE_2 0x8000C000 119 #define CONFIG_SYS_DDR_SDRAM_INTERVAL 0x03E00000 120 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 121 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x01000000 122 #define CONFIG_SYS_DDR_TIMING_4 0x00220001 123 #define CONFIG_SYS_DDR_TIMING_5 0x03402400 124 #define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600 125 #define CONFIG_SYS_DDR_WRLVL_CNTL 0x0655A604 126 #define CONFIG_SYS_DDR_CDR_1 0x80040000 127 #define CONFIG_SYS_DDR_CDR_2 0x00000000 128 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 129 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 130 #define CONFIG_SYS_DDR_CONTROL 0xc7000000 /* Type = DDR3 */ 131 #define CONFIG_SYS_DDR_CONTROL2 0x24400000 132 133 #define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d 134 #define CONFIG_SYS_DDR_ERR_DIS 0x00000000 135 #define CONFIG_SYS_DDR_SBE 0x00010000 136 137 #undef CONFIG_CLOCKS_IN_MHZ 138 139 /* 140 * Local Bus Definitions 141 */ 142 143 #define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ 144 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 145 146 #define CONFIG_SYS_BCSR_BASE 0xf8000000 147 #define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE 148 149 /*Chip select 0 - Flash*/ 150 #define CONFIG_SYS_BR0_PRELIM 0xfe000801 151 #define CONFIG_SYS_OR0_PRELIM 0xfe000ff7 152 153 /*Chip select 1 - BCSR*/ 154 #define CONFIG_SYS_BR1_PRELIM 0xf8000801 155 #define CONFIG_SYS_OR1_PRELIM 0xffffe9f7 156 157 /*Chip select 4 - PIB*/ 158 #define CONFIG_SYS_BR4_PRELIM 0xf8008801 159 #define CONFIG_SYS_OR4_PRELIM 0xffffe9f7 160 161 /*Chip select 5 - PIB*/ 162 #define CONFIG_SYS_BR5_PRELIM 0xf8010801 163 #define CONFIG_SYS_OR5_PRELIM 0xffffe9f7 164 165 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 166 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ 167 #undef CONFIG_SYS_FLASH_CHECKSUM 168 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 169 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 170 171 #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ 172 173 #define CONFIG_FLASH_CFI_DRIVER 174 #define CONFIG_SYS_FLASH_CFI 175 #define CONFIG_SYS_FLASH_EMPTY_INFO 176 177 /* Chip select 3 - NAND */ 178 #define CONFIG_SYS_NAND_BASE 0xFC000000 179 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 180 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, } 181 #define CONFIG_SYS_MAX_NAND_DEVICE 1 182 #define CONFIG_MTD_NAND_VERIFY_WRITE 1 183 #define CONFIG_CMD_NAND 1 184 #define CONFIG_NAND_FSL_ELBC 1 185 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 186 #define CONFIG_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ 187 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 188 | BR_PS_8 /* Port Size = 8 bit */ \ 189 | BR_MS_FCM /* MSEL = FCM */ \ 190 | BR_V) /* valid */ 191 #define CONFIG_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ 192 | OR_FCM_CSCT \ 193 | OR_FCM_CST \ 194 | OR_FCM_CHT \ 195 | OR_FCM_SCY_1 \ 196 | OR_FCM_TRLX \ 197 | OR_FCM_EHTR) 198 #define CONFIG_SYS_BR3_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */ 199 #define CONFIG_SYS_OR3_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */ 200 201 /* 202 * SDRAM on the LocalBus 203 */ 204 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 205 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 206 207 #define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */ 208 #define CONFIG_SYS_LBC_LBCR 0x00040000 /* LB config reg */ 209 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 210 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 211 212 #define CONFIG_SYS_INIT_RAM_LOCK 1 213 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 214 #define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ 215 216 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ 217 #define CONFIG_SYS_GBL_DATA_OFFSET \ 218 (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 219 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 220 221 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 222 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 223 224 /* Serial Port */ 225 #define CONFIG_CONS_INDEX 1 226 #define CONFIG_SERIAL_MULTI 1 227 #undef CONFIG_SERIAL_SOFTWARE_FIFO 228 #define CONFIG_SYS_NS16550 229 #define CONFIG_SYS_NS16550_SERIAL 230 #define CONFIG_SYS_NS16550_REG_SIZE 1 231 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 232 233 #define CONFIG_SYS_BAUDRATE_TABLE \ 234 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 235 236 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 237 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 238 239 /* Use the HUSH parser*/ 240 #define CONFIG_SYS_HUSH_PARSER 241 #ifdef CONFIG_SYS_HUSH_PARSER 242 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 243 #endif 244 245 /* pass open firmware flat tree */ 246 #define CONFIG_OF_LIBFDT 1 247 #define CONFIG_OF_BOARD_SETUP 1 248 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 249 250 #define CONFIG_SYS_64BIT_VSPRINTF 1 251 #define CONFIG_SYS_64BIT_STRTOUL 1 252 253 /* 254 * I2C 255 */ 256 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ 257 #define CONFIG_HARD_I2C /* I2C with hardware support*/ 258 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 259 #define CONFIG_I2C_MULTI_BUS 260 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 261 #define CONFIG_SYS_I2C_SLAVE 0x7F 262 #define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ 263 #define CONFIG_SYS_I2C_OFFSET 0x3000 264 #define CONFIG_SYS_I2C2_OFFSET 0x3100 265 266 /* 267 * I2C2 EEPROM 268 */ 269 #define CONFIG_ID_EEPROM 270 #ifdef CONFIG_ID_EEPROM 271 #define CONFIG_SYS_I2C_EEPROM_NXID 272 #endif 273 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 274 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 275 #define CONFIG_SYS_EEPROM_BUS_NUM 1 276 277 #define PLPPAR1_I2C_BIT_MASK 0x0000000F 278 #define PLPPAR1_I2C2_VAL 0x00000000 279 #define PLPPAR1_ESDHC_VAL 0x0000000A 280 #define PLPDIR1_I2C_BIT_MASK 0x0000000F 281 #define PLPDIR1_I2C2_VAL 0x0000000F 282 #define PLPDIR1_ESDHC_VAL 0x00000006 283 284 /* 285 * General PCI 286 * Memory Addresses are mapped 1-1. I/O is mapped from 0 287 */ 288 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 289 #define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 290 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 291 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 292 #define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000 293 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 294 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000 295 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 296 297 #define CONFIG_SYS_SRIO_MEM_VIRT 0xc0000000 298 #define CONFIG_SYS_SRIO_MEM_BUS 0xc0000000 299 #define CONFIG_SYS_SRIO_MEM_PHYS 0xc0000000 300 301 #ifdef CONFIG_QE 302 /* 303 * QE UEC ethernet configuration 304 */ 305 #define CONFIG_SYS_UCC_RGMII_MODE /* Set UCC work at RGMII by default */ 306 #undef CONFIG_SYS_UCC_RMII_MODE /* Set UCC work at RMII mode */ 307 308 #define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120) 309 #define CONFIG_UEC_ETH 310 #define CONFIG_ETHPRIME "FSL UEC0" 311 #define CONFIG_PHY_MODE_NEED_CHANGE 312 313 #define CONFIG_UEC_ETH1 /* GETH1 */ 314 #define CONFIG_HAS_ETH0 315 316 #ifdef CONFIG_UEC_ETH1 317 #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ 318 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE 319 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 320 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK12 321 #define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH 322 #define CONFIG_SYS_UEC1_PHY_ADDR 7 323 #define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_1000_RGMII_ID 324 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 325 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK16 /* CLK16 for RMII */ 326 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH 327 #define CONFIG_SYS_UEC1_PHY_ADDR 8 /* 0x8 for RMII */ 328 #define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_100_RMII 329 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 330 #endif /* CONFIG_UEC_ETH1 */ 331 332 #define CONFIG_UEC_ETH2 /* GETH2 */ 333 #define CONFIG_HAS_ETH1 334 335 #ifdef CONFIG_UEC_ETH2 336 #define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ 337 #define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE 338 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 339 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK17 340 #define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH 341 #define CONFIG_SYS_UEC2_PHY_ADDR 1 342 #define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_1000_RGMII_ID 343 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 344 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK16 /* CLK 16 for RMII */ 345 #define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH 346 #define CONFIG_SYS_UEC2_PHY_ADDR 0x9 /* 0x9 for RMII */ 347 #define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_100_RMII 348 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 349 #endif /* CONFIG_UEC_ETH2 */ 350 351 #define CONFIG_UEC_ETH3 /* GETH3 */ 352 #define CONFIG_HAS_ETH2 353 354 #ifdef CONFIG_UEC_ETH3 355 #define CONFIG_SYS_UEC3_UCC_NUM 2 /* UCC3 */ 356 #define CONFIG_SYS_UEC3_RX_CLK QE_CLK_NONE 357 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 358 #define CONFIG_SYS_UEC3_TX_CLK QE_CLK12 359 #define CONFIG_SYS_UEC3_ETH_TYPE GIGA_ETH 360 #define CONFIG_SYS_UEC3_PHY_ADDR 2 361 #define CONFIG_SYS_UEC3_INTERFACE_MODE ENET_1000_RGMII_ID 362 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 363 #define CONFIG_SYS_UEC3_TX_CLK QE_CLK16 /* CLK_16 for RMII */ 364 #define CONFIG_SYS_UEC3_ETH_TYPE FAST_ETH 365 #define CONFIG_SYS_UEC3_PHY_ADDR 0xA /* 0xA for RMII */ 366 #define CONFIG_SYS_UEC3_INTERFACE_MODE ENET_100_RMII 367 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 368 #endif /* CONFIG_UEC_ETH3 */ 369 370 #define CONFIG_UEC_ETH4 /* GETH4 */ 371 #define CONFIG_HAS_ETH3 372 373 #ifdef CONFIG_UEC_ETH4 374 #define CONFIG_SYS_UEC4_UCC_NUM 3 /* UCC4 */ 375 #define CONFIG_SYS_UEC4_RX_CLK QE_CLK_NONE 376 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 377 #define CONFIG_SYS_UEC4_TX_CLK QE_CLK17 378 #define CONFIG_SYS_UEC4_ETH_TYPE GIGA_ETH 379 #define CONFIG_SYS_UEC4_PHY_ADDR 3 380 #define CONFIG_SYS_UEC4_INTERFACE_MODE ENET_1000_RGMII_ID 381 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 382 #define CONFIG_SYS_UEC4_TX_CLK QE_CLK16 /* CLK16 for RMII */ 383 #define CONFIG_SYS_UEC4_ETH_TYPE FAST_ETH 384 #define CONFIG_SYS_UEC4_PHY_ADDR 0xB /* 0xB for RMII */ 385 #define CONFIG_SYS_UEC4_INTERFACE_MODE ENET_100_RMII 386 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 387 #endif /* CONFIG_UEC_ETH4 */ 388 389 #undef CONFIG_UEC_ETH6 /* GETH6 */ 390 #define CONFIG_HAS_ETH5 391 392 #ifdef CONFIG_UEC_ETH6 393 #define CONFIG_SYS_UEC6_UCC_NUM 5 /* UCC6 */ 394 #define CONFIG_SYS_UEC6_RX_CLK QE_CLK_NONE 395 #define CONFIG_SYS_UEC6_TX_CLK QE_CLK_NONE 396 #define CONFIG_SYS_UEC6_ETH_TYPE GIGA_ETH 397 #define CONFIG_SYS_UEC6_PHY_ADDR 4 398 #define CONFIG_SYS_UEC6_INTERFACE_MODE ENET_1000_SGMII 399 #endif /* CONFIG_UEC_ETH6 */ 400 401 #undef CONFIG_UEC_ETH8 /* GETH8 */ 402 #define CONFIG_HAS_ETH7 403 404 #ifdef CONFIG_UEC_ETH8 405 #define CONFIG_SYS_UEC8_UCC_NUM 7 /* UCC8 */ 406 #define CONFIG_SYS_UEC8_RX_CLK QE_CLK_NONE 407 #define CONFIG_SYS_UEC8_TX_CLK QE_CLK_NONE 408 #define CONFIG_SYS_UEC8_ETH_TYPE GIGA_ETH 409 #define CONFIG_SYS_UEC8_PHY_ADDR 6 410 #define CONFIG_SYS_UEC8_INTERFACE_MODE ENET_1000_SGMII 411 #endif /* CONFIG_UEC_ETH8 */ 412 413 #endif /* CONFIG_QE */ 414 415 #if defined(CONFIG_PCI) 416 417 #define CONFIG_NET_MULTI 418 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 419 420 #undef CONFIG_EEPRO100 421 #undef CONFIG_TULIP 422 423 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 424 425 #endif /* CONFIG_PCI */ 426 427 #ifndef CONFIG_NET_MULTI 428 #define CONFIG_NET_MULTI 1 429 #endif 430 431 /* 432 * Environment 433 */ 434 #define CONFIG_ENV_IS_IN_FLASH 1 435 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 436 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 256K(one sector) for env */ 437 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE 438 439 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 440 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 441 442 /* QE microcode/firmware address */ 443 #define CONFIG_SYS_QE_FW_ADDR 0xfff00000 444 445 /* 446 * BOOTP options 447 */ 448 #define CONFIG_BOOTP_BOOTFILESIZE 449 #define CONFIG_BOOTP_BOOTPATH 450 #define CONFIG_BOOTP_GATEWAY 451 #define CONFIG_BOOTP_HOSTNAME 452 453 454 /* 455 * Command line configuration. 456 */ 457 #include <config_cmd_default.h> 458 459 #define CONFIG_CMD_PING 460 #define CONFIG_CMD_I2C 461 #define CONFIG_CMD_MII 462 #define CONFIG_CMD_ELF 463 #define CONFIG_CMD_IRQ 464 #define CONFIG_CMD_SETEXPR 465 466 #if defined(CONFIG_PCI) 467 #define CONFIG_CMD_PCI 468 #endif 469 470 471 #undef CONFIG_WATCHDOG /* watchdog disabled */ 472 473 #define CONFIG_MMC 1 474 475 #ifdef CONFIG_MMC 476 #define CONFIG_FSL_ESDHC 477 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 478 #define CONFIG_CMD_MMC 479 #define CONFIG_GENERIC_MMC 480 #define CONFIG_CMD_EXT2 481 #define CONFIG_CMD_FAT 482 #define CONFIG_DOS_PARTITION 483 #endif 484 485 /* 486 * Miscellaneous configurable options 487 */ 488 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 489 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 490 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 491 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 492 #if defined(CONFIG_CMD_KGDB) 493 #define CONFIG_SYS_CBSIZE 2048 /* Console I/O Buffer Size */ 494 #else 495 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 496 #endif 497 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 498 /* Print Buffer Size */ 499 #define CONFIG_SYS_MAXARGS 32 /* max number of command args */ 500 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 501 /* Boot Argument Buffer Size */ 502 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 503 504 /* 505 * For booting Linux, the board info and command line data 506 * have to be in the first 16 MB of memory, since this is 507 * the maximum mapped by the Linux kernel during initialization. 508 */ 509 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) 510 /* Initial Memory map for Linux*/ 511 512 /* 513 * Internal Definitions 514 * 515 * Boot Flags 516 */ 517 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 518 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 519 520 #if defined(CONFIG_CMD_KGDB) 521 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 522 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 523 #endif 524 525 /* 526 * Environment Configuration 527 */ 528 #define CONFIG_HOSTNAME mpc8569mds 529 #define CONFIG_ROOTPATH /nfsroot 530 #define CONFIG_BOOTFILE your.uImage 531 532 #define CONFIG_SERVERIP 192.168.1.1 533 #define CONFIG_GATEWAYIP 192.168.1.1 534 #define CONFIG_NETMASK 255.255.255.0 535 536 #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ 537 538 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 539 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 540 541 #define CONFIG_BAUDRATE 115200 542 543 #define CONFIG_EXTRA_ENV_SETTINGS \ 544 "netdev=eth0\0" \ 545 "consoledev=ttyS0\0" \ 546 "ramdiskaddr=600000\0" \ 547 "ramdiskfile=your.ramdisk.u-boot\0" \ 548 "fdtaddr=400000\0" \ 549 "fdtfile=your.fdt.dtb\0" \ 550 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 551 "nfsroot=$serverip:$rootpath " \ 552 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 553 "console=$consoledev,$baudrate $othbootargs\0" \ 554 "ramargs=setenv bootargs root=/dev/ram rw " \ 555 "console=$consoledev,$baudrate $othbootargs\0" \ 556 557 #define CONFIG_NFSBOOTCOMMAND \ 558 "run nfsargs;" \ 559 "tftp $loadaddr $bootfile;" \ 560 "tftp $fdtaddr $fdtfile;" \ 561 "bootm $loadaddr - $fdtaddr" 562 563 #define CONFIG_RAMBOOTCOMMAND \ 564 "run ramargs;" \ 565 "tftp $ramdiskaddr $ramdiskfile;" \ 566 "tftp $loadaddr $bootfile;" \ 567 "bootm $loadaddr $ramdiskaddr" 568 569 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 570 571 #endif /* __CONFIG_H */ 572