1 /* 2 * Copyright (C) 2007 Freescale Semiconductor, Inc. 3 * Dave Liu <daveliu@freescale.com> 4 * 5 * This program is free software; you can redistribute it and/or 6 * modify it under the terms of the GNU General Public License as 7 * published by the Free Software Foundation; either version 2 of 8 * the License, or (at your option) any later version. 9 * 10 * This program is distributed in the hope that it will be useful, 11 * but WITHOUT ANY WARRANTY; without even the implied warranty of 12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 13 * GNU General Public License for more details. 14 * 15 * You should have received a copy of the GNU General Public License 16 * along with this program; if not, write to the Free Software 17 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 18 * MA 02111-1307 USA 19 */ 20 21 #ifndef __CONFIG_H 22 #define __CONFIG_H 23 24 #undef DEBUG 25 26 /* 27 * High Level Configuration Options 28 */ 29 #define CONFIG_E300 1 /* E300 family */ 30 #define CONFIG_MPC83XX 1 /* MPC83XX family */ 31 #define CONFIG_MPC837X 1 /* MPC837X CPU specific */ 32 #define CONFIG_MPC837XEMDS 1 /* MPC837XEMDS board specific */ 33 34 /* 35 * System Clock Setup 36 */ 37 #ifdef CONFIG_PCISLAVE 38 #define CONFIG_83XX_PCICLK 66000000 /* in HZ */ 39 #else 40 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 41 #endif 42 43 #ifndef CONFIG_SYS_CLK_FREQ 44 #define CONFIG_SYS_CLK_FREQ 66000000 45 #endif 46 47 /* 48 * Hardware Reset Configuration Word 49 * if CLKIN is 66MHz, then 50 * CSB = 396MHz, CORE = 594MHz, DDRC = 396MHz, LBC = 396MHz 51 */ 52 #define CFG_HRCW_LOW (\ 53 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 54 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 55 HRCWL_SVCOD_DIV_2 |\ 56 HRCWL_CSB_TO_CLKIN_6X1 |\ 57 HRCWL_CORE_TO_CSB_1_5X1) 58 59 #ifdef CONFIG_PCISLAVE 60 #define CFG_HRCW_HIGH (\ 61 HRCWH_PCI_AGENT |\ 62 HRCWH_PCI1_ARBITER_DISABLE |\ 63 HRCWH_CORE_ENABLE |\ 64 HRCWH_FROM_0XFFF00100 |\ 65 HRCWH_BOOTSEQ_DISABLE |\ 66 HRCWH_SW_WATCHDOG_DISABLE |\ 67 HRCWH_ROM_LOC_LOCAL_16BIT |\ 68 HRCWH_RL_EXT_LEGACY |\ 69 HRCWH_TSEC1M_IN_RGMII |\ 70 HRCWH_TSEC2M_IN_RGMII |\ 71 HRCWH_BIG_ENDIAN |\ 72 HRCWH_LDP_CLEAR) 73 #else 74 #define CFG_HRCW_HIGH (\ 75 HRCWH_PCI_HOST |\ 76 HRCWH_PCI1_ARBITER_ENABLE |\ 77 HRCWH_CORE_ENABLE |\ 78 HRCWH_FROM_0X00000100 |\ 79 HRCWH_BOOTSEQ_DISABLE |\ 80 HRCWH_SW_WATCHDOG_DISABLE |\ 81 HRCWH_ROM_LOC_LOCAL_16BIT |\ 82 HRCWH_RL_EXT_LEGACY |\ 83 HRCWH_TSEC1M_IN_RGMII |\ 84 HRCWH_TSEC2M_IN_RGMII |\ 85 HRCWH_BIG_ENDIAN |\ 86 HRCWH_LDP_CLEAR) 87 #endif 88 89 /* 90 * eTSEC Clock Config 91 */ 92 #define CFG_SCCR_TSEC1CM 1 /* CSB:eTSEC1 = 1:1 */ 93 #define CFG_SCCR_TSEC2CM 1 /* CSB:eTSEC2 = 1:1 */ 94 95 /* 96 * System IO Config 97 */ 98 #define CFG_SICRH 0x00000000 99 #define CFG_SICRL 0x00000000 100 101 /* 102 * Output Buffer Impedance 103 */ 104 #define CFG_OBIR 0x31100000 105 106 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ 107 #define CONFIG_BOARD_EARLY_INIT_R 108 109 /* 110 * IMMR new address 111 */ 112 #define CFG_IMMR 0xE0000000 113 114 /* 115 * DDR Setup 116 */ 117 #define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ 118 #define CFG_SDRAM_BASE CFG_DDR_BASE 119 #define CFG_DDR_SDRAM_BASE CFG_DDR_BASE 120 #define CFG_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 121 #define CFG_83XX_DDR_USES_CS0 122 #define CFG_DDRCDR_VALUE 0x80080001 /* ODT 150ohm on SoC */ 123 124 #undef CONFIG_DDR_ECC /* support DDR ECC function */ 125 #undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ 126 127 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 128 #define CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */ 129 130 #if defined(CONFIG_SPD_EEPROM) 131 #define SPD_EEPROM_ADDRESS 0x51 /* I2C address of DDR SODIMM SPD */ 132 #else 133 /* 134 * Manually set up DDR parameters 135 * WHITE ELECTRONIC DESGGNS - W3HG64M72EEU403PD4 SO-DIMM 136 * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5 137 */ 138 #define CFG_DDR_SIZE 512 /* MB */ 139 #define CFG_DDR_CS0_BNDS 0x0000001f 140 #define CFG_DDR_CS0_CONFIG ( CSCONFIG_EN \ 141 | 0x00010000 /* ODT_WR to CSn */ \ 142 | CSCONFIG_ROW_BIT_14 | CSCONFIG_COL_BIT_10 ) 143 /* 0x80010202 */ 144 #define CFG_DDR_TIMING_3 0x00000000 145 #define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ 146 | ( 0 << TIMING_CFG0_WRT_SHIFT ) \ 147 | ( 0 << TIMING_CFG0_RRT_SHIFT ) \ 148 | ( 0 << TIMING_CFG0_WWT_SHIFT ) \ 149 | ( 6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \ 150 | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \ 151 | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \ 152 | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) ) 153 /* 0x00620802 */ 154 #define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \ 155 | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \ 156 | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \ 157 | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \ 158 | (13 << TIMING_CFG1_REFREC_SHIFT ) \ 159 | ( 3 << TIMING_CFG1_WRREC_SHIFT ) \ 160 | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \ 161 | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) ) 162 /* 0x3935d322 */ 163 #define CFG_DDR_TIMING_2 ( ( 2 << TIMING_CFG2_ADD_LAT_SHIFT ) \ 164 | ( 6 << TIMING_CFG2_CPO_SHIFT ) \ 165 | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \ 166 | ( 4 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \ 167 | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \ 168 | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \ 169 | ( 8 << TIMING_CFG2_FOUR_ACT_SHIFT) ) 170 /* 0x231088c8 */ 171 #define CFG_DDR_INTERVAL ( ( 0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT ) \ 172 | ( 0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) ) 173 /* 0x03E00100 */ 174 #define CFG_DDR_SDRAM_CFG 0x43000000 175 #define CFG_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ 176 #define CFG_DDR_MODE ( ( 0x0450 << SDRAM_MODE_ESD_SHIFT ) \ 177 | ( 0x1432 << SDRAM_MODE_SD_SHIFT ) ) 178 /* ODT 150ohm CL=3, AL=2 on SDRAM */ 179 #define CFG_DDR_MODE2 0x00000000 180 #endif 181 182 /* 183 * Memory test 184 */ 185 #undef CFG_DRAM_TEST /* memory test, takes time */ 186 #define CFG_MEMTEST_START 0x00040000 /* memtest region */ 187 #define CFG_MEMTEST_END 0x00140000 188 189 /* 190 * The reserved memory 191 */ 192 #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ 193 194 #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) 195 #define CFG_RAMBOOT 196 #else 197 #undef CFG_RAMBOOT 198 #endif 199 200 #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 201 #define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 202 203 /* 204 * Initial RAM Base Address Setup 205 */ 206 #define CFG_INIT_RAM_LOCK 1 207 #define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 208 #define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ 209 #define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ 210 #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) 211 212 /* 213 * Local Bus Configuration & Clock Setup 214 */ 215 #define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_8) 216 #define CFG_LBC_LBCR 0x00000000 217 218 /* 219 * FLASH on the Local Bus 220 */ 221 #define CFG_FLASH_CFI /* use the Common Flash Interface */ 222 #define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ 223 #define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ 224 #define CFG_FLASH_SIZE 32 /* max FLASH size is 32M */ 225 226 #define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ 227 #define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ 228 229 #define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \ 230 (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ 231 BR_V) /* valid */ 232 #define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ 233 OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ 234 OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) 235 236 #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ 237 #define CFG_MAX_FLASH_SECT 256 /* max sectors per device */ 238 239 #undef CFG_FLASH_CHECKSUM 240 #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 241 #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 242 243 /* 244 * BCSR on the Local Bus 245 */ 246 #define CFG_BCSR 0xF8000000 247 #define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */ 248 #define CFG_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */ 249 250 #define CFG_BR1_PRELIM (CFG_BCSR | 0x00000801) /* Port size=8bit, MSEL=GPCM */ 251 #define CFG_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ 252 253 /* 254 * NAND Flash on the Local Bus 255 */ 256 #define CFG_NAND_BASE 0xE0600000 /* 0xE0600000 */ 257 #define CFG_BR3_PRELIM ( CFG_NAND_BASE \ 258 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 259 | BR_PS_8 /* Port Size = 8 bit */ \ 260 | BR_MS_FCM /* MSEL = FCM */ \ 261 | BR_V ) /* valid */ 262 #define CFG_OR3_PRELIM ( 0xFFFF8000 /* length 32K */ \ 263 | OR_FCM_CSCT \ 264 | OR_FCM_CST \ 265 | OR_FCM_CHT \ 266 | OR_FCM_SCY_1 \ 267 | OR_FCM_TRLX \ 268 | OR_FCM_EHTR ) 269 /* 0xFFFF8396 */ 270 271 #define CFG_LBLAWBAR3_PRELIM CFG_NAND_BASE 272 #define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */ 273 274 /* 275 * Serial Port 276 */ 277 #define CONFIG_CONS_INDEX 1 278 #undef CONFIG_SERIAL_SOFTWARE_FIFO 279 #define CFG_NS16550 280 #define CFG_NS16550_SERIAL 281 #define CFG_NS16550_REG_SIZE 1 282 #define CFG_NS16550_CLK get_bus_freq(0) 283 284 #define CFG_BAUDRATE_TABLE \ 285 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 286 287 #define CFG_NS16550_COM1 (CFG_IMMR+0x4500) 288 #define CFG_NS16550_COM2 (CFG_IMMR+0x4600) 289 290 /* Use the HUSH parser */ 291 #define CFG_HUSH_PARSER 292 #ifdef CFG_HUSH_PARSER 293 #define CFG_PROMPT_HUSH_PS2 "> " 294 #endif 295 296 /* Pass open firmware flat tree */ 297 #define CONFIG_OF_LIBFDT 1 298 #define CONFIG_OF_BOARD_SETUP 1 299 #define CONFIG_OF_HAS_BD_T 1 300 #define CONFIG_OF_HAS_UBOOT_ENV 1 301 302 #define OF_CPU "PowerPC,837x@0" 303 #define OF_SOC "soc837x@e0000000" 304 #define OF_TBCLK (bd->bi_busfreq / 4) 305 #define OF_STDOUT_PATH "/soc837x@e0000000/serial@4500" 306 307 /* I2C */ 308 #define CONFIG_HARD_I2C /* I2C with hardware support */ 309 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 310 #define CONFIG_FSL_I2C 311 #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ 312 #define CFG_I2C_SLAVE 0x7F 313 #define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */ 314 #define CFG_I2C_OFFSET 0x3000 315 #define CFG_I2C2_OFFSET 0x3100 316 317 /* 318 * Config on-board RTC 319 */ 320 #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ 321 #define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 322 323 /* 324 * General PCI 325 * Addresses are mapped 1-1. 326 */ 327 #define CFG_PCI_MEM_BASE 0x80000000 328 #define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE 329 #define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */ 330 #define CFG_PCI_MMIO_BASE 0x90000000 331 #define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE 332 #define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */ 333 #define CFG_PCI_IO_BASE 0xE0300000 334 #define CFG_PCI_IO_PHYS 0xE0300000 335 #define CFG_PCI_IO_SIZE 0x100000 /* 1M */ 336 337 #define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE 338 #define CFG_PCI_SLV_MEM_BUS 0x00000000 339 #define CFG_PCI_SLV_MEM_SIZE 0x80000000 340 341 #ifdef CONFIG_PCI 342 #define CONFIG_83XX_GENERIC_PCI 1 /* Use generic PCI setup */ 343 #define CONFIG_PQ_MDS_PIB 1 /* PQ MDS Platform IO Board */ 344 345 #define CONFIG_NET_MULTI 346 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 347 348 #undef CONFIG_EEPRO100 349 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 350 #define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 351 #endif /* CONFIG_PCI */ 352 353 #ifndef CONFIG_NET_MULTI 354 #define CONFIG_NET_MULTI 1 355 #endif 356 357 /* 358 * TSEC 359 */ 360 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 361 #define CFG_TSEC1_OFFSET 0x24000 362 #define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET) 363 #define CFG_TSEC2_OFFSET 0x25000 364 #define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET) 365 366 /* 367 * TSEC ethernet configuration 368 */ 369 #define CONFIG_MII 1 /* MII PHY management */ 370 #define CONFIG_TSEC1 1 371 #define CONFIG_TSEC1_NAME "eTSEC0" 372 #define CONFIG_TSEC2 1 373 #define CONFIG_TSEC2_NAME "eTSEC1" 374 #define TSEC1_PHY_ADDR 2 375 #define TSEC2_PHY_ADDR 3 376 #define TSEC1_PHYIDX 0 377 #define TSEC2_PHYIDX 0 378 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 379 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 380 381 /* Options are: TSEC[0-1] */ 382 #define CONFIG_ETHPRIME "eTSEC1" 383 384 /* 385 * Environment 386 */ 387 #ifndef CFG_RAMBOOT 388 #define CFG_ENV_IS_IN_FLASH 1 389 #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) 390 #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 391 #define CFG_ENV_SIZE 0x2000 392 #else 393 #define CFG_NO_FLASH 1 /* Flash is not usable now */ 394 #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 395 #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) 396 #define CFG_ENV_SIZE 0x2000 397 #endif 398 399 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 400 #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 401 402 /* 403 * BOOTP options 404 */ 405 #define CONFIG_BOOTP_BOOTFILESIZE 406 #define CONFIG_BOOTP_BOOTPATH 407 #define CONFIG_BOOTP_GATEWAY 408 #define CONFIG_BOOTP_HOSTNAME 409 410 411 /* 412 * Command line configuration. 413 */ 414 #include <config_cmd_default.h> 415 416 #define CONFIG_CMD_PING 417 #define CONFIG_CMD_I2C 418 #define CONFIG_CMD_MII 419 #define CONFIG_CMD_DATE 420 421 #if defined(CONFIG_PCI) 422 #define CONFIG_CMD_PCI 423 #endif 424 425 #if defined(CFG_RAMBOOT) 426 #undef CONFIG_CMD_ENV 427 #undef CONFIG_CMD_LOADS 428 #endif 429 430 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 431 432 #undef CONFIG_WATCHDOG /* watchdog disabled */ 433 434 /* 435 * Miscellaneous configurable options 436 */ 437 #define CFG_LONGHELP /* undef to save memory */ 438 #define CFG_LOAD_ADDR 0x2000000 /* default load address */ 439 #define CFG_PROMPT "=> " /* Monitor Command Prompt */ 440 441 #if defined(CONFIG_CMD_KGDB) 442 #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ 443 #else 444 #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ 445 #endif 446 447 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ 448 #define CFG_MAXARGS 16 /* max number of command args */ 449 #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ 450 #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ 451 452 /* 453 * For booting Linux, the board info and command line data 454 * have to be in the first 8 MB of memory, since this is 455 * the maximum mapped by the Linux kernel during initialization. 456 */ 457 #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 458 459 /* 460 * Core HID Setup 461 */ 462 #define CFG_HID0_INIT 0x000000000 463 #define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK 464 #define CFG_HID2 HID2_HBE 465 466 /* 467 * Cache Config 468 */ 469 #define CFG_DCACHE_SIZE 32768 470 #define CFG_CACHELINE_SIZE 32 471 #if defined(CONFIG_CMD_KGDB) 472 #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ 473 #endif 474 475 /* 476 * MMU Setup 477 */ 478 479 /* DDR: cache cacheable */ 480 #define CFG_SDRAM_LOWER CFG_SDRAM_BASE 481 #define CFG_SDRAM_UPPER (CFG_SDRAM_BASE + 0x10000000) 482 483 #define CFG_IBAT0L (CFG_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE) 484 #define CFG_IBAT0U (CFG_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP) 485 #define CFG_DBAT0L CFG_IBAT0L 486 #define CFG_DBAT0U CFG_IBAT0U 487 488 #define CFG_IBAT1L (CFG_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE) 489 #define CFG_IBAT1U (CFG_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP) 490 #define CFG_DBAT1L CFG_IBAT1L 491 #define CFG_DBAT1U CFG_IBAT1U 492 493 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ 494 #define CFG_IBAT2L (CFG_IMMR | BATL_PP_10 | \ 495 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 496 #define CFG_IBAT2U (CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP) 497 #define CFG_DBAT2L CFG_IBAT2L 498 #define CFG_DBAT2U CFG_IBAT2U 499 500 /* BCSR: cache-inhibit and guarded */ 501 #define CFG_IBAT3L (CFG_BCSR | BATL_PP_10 | \ 502 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 503 #define CFG_IBAT3U (CFG_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) 504 #define CFG_DBAT3L CFG_IBAT3L 505 #define CFG_DBAT3U CFG_IBAT3U 506 507 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 508 #define CFG_IBAT4L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) 509 #define CFG_IBAT4U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) 510 #define CFG_DBAT4L (CFG_FLASH_BASE | BATL_PP_10 | \ 511 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 512 #define CFG_DBAT4U CFG_IBAT4U 513 514 /* Stack in dcache: cacheable, no memory coherence */ 515 #define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10) 516 #define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 517 #define CFG_DBAT5L CFG_IBAT5L 518 #define CFG_DBAT5U CFG_IBAT5U 519 520 #ifdef CONFIG_PCI 521 /* PCI MEM space: cacheable */ 522 #define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) 523 #define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) 524 #define CFG_DBAT6L CFG_IBAT6L 525 #define CFG_DBAT6U CFG_IBAT6U 526 /* PCI MMIO space: cache-inhibit and guarded */ 527 #define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \ 528 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 529 #define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) 530 #define CFG_DBAT7L CFG_IBAT7L 531 #define CFG_DBAT7U CFG_IBAT7U 532 #else 533 #define CFG_IBAT6L (0) 534 #define CFG_IBAT6U (0) 535 #define CFG_IBAT7L (0) 536 #define CFG_IBAT7U (0) 537 #define CFG_DBAT6L CFG_IBAT6L 538 #define CFG_DBAT6U CFG_IBAT6U 539 #define CFG_DBAT7L CFG_IBAT7L 540 #define CFG_DBAT7U CFG_IBAT7U 541 #endif 542 543 /* 544 * Internal Definitions 545 * 546 * Boot Flags 547 */ 548 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 549 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 550 551 #if defined(CONFIG_CMD_KGDB) 552 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 553 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 554 #endif 555 556 /* 557 * Environment Configuration 558 */ 559 560 #define CONFIG_ENV_OVERWRITE 561 562 #if defined(CONFIG_TSEC_ENET) 563 #define CONFIG_HAS_ETH0 564 #define CONFIG_ETHADDR 00:E0:0C:00:83:79 565 #define CONFIG_HAS_ETH1 566 #define CONFIG_ETH1ADDR 00:E0:0C:00:83:78 567 #endif 568 569 #define CONFIG_BAUDRATE 115200 570 571 #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ 572 573 #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ 574 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 575 576 #define CONFIG_EXTRA_ENV_SETTINGS \ 577 "netdev=eth0\0" \ 578 "consoledev=ttyS0\0" \ 579 "ramdiskaddr=1000000\0" \ 580 "ramdiskfile=ramfs.83xx\0" \ 581 "fdtaddr=400000\0" \ 582 "fdtfile=mpc837xemds.dtb\0" \ 583 "" 584 585 #define CONFIG_NFSBOOTCOMMAND \ 586 "setenv bootargs root=/dev/nfs rw " \ 587 "nfsroot=$serverip:$rootpath " \ 588 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 589 "console=$consoledev,$baudrate $othbootargs;" \ 590 "tftp $loadaddr $bootfile;" \ 591 "tftp $fdtaddr $fdtfile;" \ 592 "bootm $loadaddr - $fdtaddr" 593 594 #define CONFIG_RAMBOOTCOMMAND \ 595 "setenv bootargs root=/dev/ram rw " \ 596 "console=$consoledev,$baudrate $othbootargs;" \ 597 "tftp $ramdiskaddr $ramdiskfile;" \ 598 "tftp $loadaddr $bootfile;" \ 599 "tftp $fdtaddr $fdtfile;" \ 600 "bootm $loadaddr $ramdiskaddr $fdtaddr" 601 602 603 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 604 605 #endif /* __CONFIG_H */ 606