1 /* 2 * (C) Copyright 2006-2010 3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * mpc8349emds board configuration file 10 * 11 */ 12 13 #ifndef __CONFIG_H 14 #define __CONFIG_H 15 16 /* 17 * High Level Configuration Options 18 */ 19 #define CONFIG_E300 1 /* E300 Family */ 20 #define CONFIG_MPC834x 1 /* MPC834x family */ 21 #define CONFIG_MPC8349 1 /* MPC8349 specific */ 22 #define CONFIG_MPC8349EMDS 1 /* MPC8349EMDS board specific */ 23 24 #define CONFIG_SYS_TEXT_BASE 0xFE000000 25 26 #define CONFIG_PCI_66M 27 #ifdef CONFIG_PCI_66M 28 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 29 #else 30 #define CONFIG_83XX_CLKIN 33000000 /* in Hz */ 31 #endif 32 33 #ifdef CONFIG_PCISLAVE 34 #define CONFIG_83XX_PCICLK 66666666 /* in Hz */ 35 #endif /* CONFIG_PCISLAVE */ 36 37 #ifndef CONFIG_SYS_CLK_FREQ 38 #ifdef CONFIG_PCI_66M 39 #define CONFIG_SYS_CLK_FREQ 66000000 40 #define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1 41 #else 42 #define CONFIG_SYS_CLK_FREQ 33000000 43 #define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1 44 #endif 45 #endif 46 47 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ 48 49 #define CONFIG_SYS_IMMR 0xE0000000 50 51 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 52 #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ 53 #define CONFIG_SYS_MEMTEST_END 0x00100000 54 55 /* 56 * DDR Setup 57 */ 58 #define CONFIG_DDR_ECC /* support DDR ECC function */ 59 #define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */ 60 #define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ 61 62 /* 63 * define CONFIG_SYS_FSL_DDR2 to use unified DDR driver 64 * undefine it to use old spd_sdram.c 65 */ 66 #define CONFIG_SYS_FSL_DDR2 67 #ifdef CONFIG_SYS_FSL_DDR2 68 #define CONFIG_SYS_FSL_DDRC_GEN2 69 #define CONFIG_SYS_SPD_BUS_NUM 0 70 #define SPD_EEPROM_ADDRESS1 0x52 71 #define SPD_EEPROM_ADDRESS2 0x51 72 #define CONFIG_NUM_DDR_CONTROLLERS 1 73 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 74 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 75 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 76 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 77 #endif 78 79 /* 80 * 32-bit data path mode. 81 * 82 * Please note that using this mode for devices with the real density of 64-bit 83 * effectively reduces the amount of available memory due to the effect of 84 * wrapping around while translating address to row/columns, for example in the 85 * 256MB module the upper 128MB get aliased with contents of the lower 86 * 128MB); normally this define should be used for devices with real 32-bit 87 * data path. 88 */ 89 #undef CONFIG_DDR_32BIT 90 91 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/ 92 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 93 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 94 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ 95 | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) 96 #undef CONFIG_DDR_2T_TIMING 97 98 /* 99 * DDRCDR - DDR Control Driver Register 100 */ 101 #define CONFIG_SYS_DDRCDR_VALUE 0x80080001 102 103 #if defined(CONFIG_SPD_EEPROM) 104 /* 105 * Determine DDR configuration from I2C interface. 106 */ 107 #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ 108 #else 109 /* 110 * Manually set up DDR parameters 111 */ 112 #define CONFIG_SYS_DDR_SIZE 256 /* MB */ 113 #if defined(CONFIG_DDR_II) 114 #define CONFIG_SYS_DDRCDR 0x80080001 115 #define CONFIG_SYS_DDR_CS2_BNDS 0x0000000f 116 #define CONFIG_SYS_DDR_CS2_CONFIG 0x80330102 117 #define CONFIG_SYS_DDR_TIMING_0 0x00220802 118 #define CONFIG_SYS_DDR_TIMING_1 0x38357322 119 #define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8 120 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 121 #define CONFIG_SYS_DDR_CLK_CNTL 0x02000000 122 #define CONFIG_SYS_DDR_MODE 0x47d00432 123 #define CONFIG_SYS_DDR_MODE2 0x8000c000 124 #define CONFIG_SYS_DDR_INTERVAL 0x03cf0080 125 #define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000 126 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 127 #else 128 #define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \ 129 | CSCONFIG_ROW_BIT_13 \ 130 | CSCONFIG_COL_BIT_10) 131 #define CONFIG_SYS_DDR_TIMING_1 0x36332321 132 #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ 133 #define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ 134 #define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */ 135 136 #if defined(CONFIG_DDR_32BIT) 137 /* set burst length to 8 for 32-bit data path */ 138 /* DLL,normal,seq,4/2.5, 8 burst len */ 139 #define CONFIG_SYS_DDR_MODE 0x00000023 140 #else 141 /* the default burst length is 4 - for 64-bit data path */ 142 /* DLL,normal,seq,4/2.5, 4 burst len */ 143 #define CONFIG_SYS_DDR_MODE 0x00000022 144 #endif 145 #endif 146 #endif 147 148 /* 149 * SDRAM on the Local Bus 150 */ 151 #define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */ 152 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 153 154 /* 155 * FLASH on the Local Bus 156 */ 157 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 158 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 159 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */ 160 #define CONFIG_SYS_FLASH_SIZE 32 /* max flash size in MB */ 161 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 162 /* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */ 163 164 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 165 | BR_PS_16 /* 16 bit port */ \ 166 | BR_MS_GPCM /* MSEL = GPCM */ \ 167 | BR_V) /* valid */ 168 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 169 | OR_UPM_XAM \ 170 | OR_GPCM_CSNT \ 171 | OR_GPCM_ACS_DIV2 \ 172 | OR_GPCM_XACS \ 173 | OR_GPCM_SCY_15 \ 174 | OR_GPCM_TRLX_SET \ 175 | OR_GPCM_EHTR_SET \ 176 | OR_GPCM_EAD) 177 178 /* window base at flash base */ 179 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 180 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) 181 182 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 183 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ 184 185 #undef CONFIG_SYS_FLASH_CHECKSUM 186 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 187 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 188 189 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 190 191 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 192 #define CONFIG_SYS_RAMBOOT 193 #else 194 #undef CONFIG_SYS_RAMBOOT 195 #endif 196 197 /* 198 * BCSR register on local bus 32KB, 8-bit wide for MDS config reg 199 */ 200 #define CONFIG_SYS_BCSR 0xE2400000 201 /* Access window base at BCSR base */ 202 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR 203 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 204 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \ 205 | BR_PS_8 \ 206 | BR_MS_GPCM \ 207 | BR_V) 208 /* 0x00000801 */ 209 #define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ 210 | OR_GPCM_XAM \ 211 | OR_GPCM_CSNT \ 212 | OR_GPCM_SCY_15 \ 213 | OR_GPCM_TRLX_CLEAR \ 214 | OR_GPCM_EHTR_CLEAR) 215 /* 0xFFFFE8F0 */ 216 217 #define CONFIG_SYS_INIT_RAM_LOCK 1 218 #define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */ 219 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ 220 221 #define CONFIG_SYS_GBL_DATA_OFFSET \ 222 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 223 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 224 225 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ 226 #define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ 227 228 /* 229 * Local Bus LCRR and LBCR regs 230 * LCRR: DLL bypass, Clock divider is 4 231 * External Local Bus rate is 232 * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV 233 */ 234 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 235 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 236 #define CONFIG_SYS_LBC_LBCR 0x00000000 237 238 /* 239 * The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory. 240 * if board has SRDAM on local bus, you can define CONFIG_SYS_LB_SDRAM 241 */ 242 #undef CONFIG_SYS_LB_SDRAM 243 244 #ifdef CONFIG_SYS_LB_SDRAM 245 /* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */ 246 /* 247 * Base Register 2 and Option Register 2 configure SDRAM. 248 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. 249 * 250 * For BR2, need: 251 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 252 * port-size = 32-bits = BR2[19:20] = 11 253 * no parity checking = BR2[21:22] = 00 254 * SDRAM for MSEL = BR2[24:26] = 011 255 * Valid = BR[31] = 1 256 * 257 * 0 4 8 12 16 20 24 28 258 * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861 259 */ 260 261 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_LBC_SDRAM_BASE \ 262 | BR_PS_32 /* 32-bit port */ \ 263 | BR_MS_SDRAM /* MSEL = SDRAM */ \ 264 | BR_V) /* Valid */ 265 /* 0xF0001861 */ 266 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE 267 #define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) 268 269 /* 270 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. 271 * 272 * For OR2, need: 273 * 64MB mask for AM, OR2[0:7] = 1111 1100 274 * XAM, OR2[17:18] = 11 275 * 9 columns OR2[19-21] = 010 276 * 13 rows OR2[23-25] = 100 277 * EAD set for extra time OR[31] = 1 278 * 279 * 0 4 8 12 16 20 24 28 280 * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901 281 */ 282 283 #define CONFIG_SYS_OR2_PRELIM (OR_AM_64MB \ 284 | OR_SDRAM_XAM \ 285 | ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \ 286 | ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \ 287 | OR_SDRAM_EAD) 288 /* 0xFC006901 */ 289 290 /* LB sdram refresh timer, about 6us */ 291 #define CONFIG_SYS_LBC_LSRT 0x32000000 292 /* LB refresh timer prescal, 266MHz/32 */ 293 #define CONFIG_SYS_LBC_MRTPR 0x20000000 294 295 #define CONFIG_SYS_LBC_LSDMR_COMMON (LSDMR_RFEN \ 296 | LSDMR_BSMA1516 \ 297 | LSDMR_RFCR8 \ 298 | LSDMR_PRETOACT6 \ 299 | LSDMR_ACTTORW3 \ 300 | LSDMR_BL8 \ 301 | LSDMR_WRC3 \ 302 | LSDMR_CL3) 303 304 /* 305 * SDRAM Controller configuration sequence. 306 */ 307 #define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL) 308 #define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) 309 #define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) 310 #define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) 311 #define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL) 312 #endif 313 314 /* 315 * Serial Port 316 */ 317 #define CONFIG_CONS_INDEX 1 318 #define CONFIG_SYS_NS16550_SERIAL 319 #define CONFIG_SYS_NS16550_REG_SIZE 1 320 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 321 322 #define CONFIG_SYS_BAUDRATE_TABLE \ 323 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 324 325 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 326 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 327 328 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 329 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 330 331 /* I2C */ 332 #define CONFIG_SYS_I2C 333 #define CONFIG_SYS_I2C_FSL 334 #define CONFIG_SYS_FSL_I2C_SPEED 400000 335 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 336 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 337 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 338 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 339 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 340 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 341 342 /* SPI */ 343 #define CONFIG_MPC8XXX_SPI 344 #undef CONFIG_SOFT_SPI /* SPI bit-banged */ 345 346 /* GPIOs. Used as SPI chip selects */ 347 #define CONFIG_SYS_GPIO1_PRELIM 348 #define CONFIG_SYS_GPIO1_DIR 0xC0000000 /* SPI CS on 0, LED on 1 */ 349 #define CONFIG_SYS_GPIO1_DAT 0xC0000000 /* Both are active LOW */ 350 351 /* TSEC */ 352 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 353 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 354 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 355 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) 356 357 /* USB */ 358 #define CONFIG_SYS_USE_MPC834XSYS_USB_PHY 1 /* Use SYS board PHY */ 359 360 /* 361 * General PCI 362 * Addresses are mapped 1-1. 363 */ 364 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 365 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 366 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 367 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 368 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE 369 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ 370 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 371 #define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 372 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ 373 374 #define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000 375 #define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE 376 #define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ 377 #define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000 378 #define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE 379 #define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */ 380 #define CONFIG_SYS_PCI2_IO_BASE 0x00000000 381 #define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000 382 #define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ 383 384 #if defined(CONFIG_PCI) 385 386 #define PCI_ONE_PCI1 387 #if defined(PCI_64BIT) 388 #undef PCI_ALL_PCI1 389 #undef PCI_TWO_PCI1 390 #undef PCI_ONE_PCI1 391 #endif 392 393 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 394 #define CONFIG_83XX_PCI_STREAMING 395 396 #undef CONFIG_EEPRO100 397 #undef CONFIG_TULIP 398 399 #if !defined(CONFIG_PCI_PNP) 400 #define PCI_ENET0_IOADDR 0xFIXME 401 #define PCI_ENET0_MEMADDR 0xFIXME 402 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ 403 #endif 404 405 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 406 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 407 408 #endif /* CONFIG_PCI */ 409 410 /* 411 * TSEC configuration 412 */ 413 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 414 415 #if defined(CONFIG_TSEC_ENET) 416 417 #define CONFIG_GMII 1 /* MII PHY management */ 418 #define CONFIG_TSEC1 1 419 #define CONFIG_TSEC1_NAME "TSEC0" 420 #define CONFIG_TSEC2 1 421 #define CONFIG_TSEC2_NAME "TSEC1" 422 #define TSEC1_PHY_ADDR 0 423 #define TSEC2_PHY_ADDR 1 424 #define TSEC1_PHYIDX 0 425 #define TSEC2_PHYIDX 0 426 #define TSEC1_FLAGS TSEC_GIGABIT 427 #define TSEC2_FLAGS TSEC_GIGABIT 428 429 /* Options are: TSEC[0-1] */ 430 #define CONFIG_ETHPRIME "TSEC0" 431 432 #endif /* CONFIG_TSEC_ENET */ 433 434 /* 435 * Configure on-board RTC 436 */ 437 #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ 438 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 439 440 /* 441 * Environment 442 */ 443 #ifndef CONFIG_SYS_RAMBOOT 444 #define CONFIG_ENV_IS_IN_FLASH 1 445 #define CONFIG_ENV_ADDR \ 446 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 447 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 448 #define CONFIG_ENV_SIZE 0x2000 449 450 /* Address and size of Redundant Environment Sector */ 451 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 452 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 453 454 #else 455 #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ 456 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 457 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 458 #define CONFIG_ENV_SIZE 0x2000 459 #endif 460 461 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 462 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 463 464 /* 465 * BOOTP options 466 */ 467 #define CONFIG_BOOTP_BOOTFILESIZE 468 #define CONFIG_BOOTP_BOOTPATH 469 #define CONFIG_BOOTP_GATEWAY 470 #define CONFIG_BOOTP_HOSTNAME 471 472 /* 473 * Command line configuration. 474 */ 475 #define CONFIG_CMD_DATE 476 477 #if defined(CONFIG_PCI) 478 #define CONFIG_CMD_PCI 479 #endif 480 481 #undef CONFIG_WATCHDOG /* watchdog disabled */ 482 483 /* 484 * Miscellaneous configurable options 485 */ 486 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 487 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 488 489 #if defined(CONFIG_CMD_KGDB) 490 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 491 #else 492 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 493 #endif 494 495 /* Print Buffer Size */ 496 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 497 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 498 /* Boot Argument Buffer Size */ 499 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 500 501 /* 502 * For booting Linux, the board info and command line data 503 * have to be in the first 256 MB of memory, since this is 504 * the maximum mapped by the Linux kernel during initialization. 505 */ 506 /* Initial Memory map for Linux*/ 507 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) 508 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 509 510 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ 511 512 #if 1 /*528/264*/ 513 #define CONFIG_SYS_HRCW_LOW (\ 514 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 515 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 516 HRCWL_CSB_TO_CLKIN |\ 517 HRCWL_VCO_1X2 |\ 518 HRCWL_CORE_TO_CSB_2X1) 519 #elif 0 /*396/132*/ 520 #define CONFIG_SYS_HRCW_LOW (\ 521 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 522 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 523 HRCWL_CSB_TO_CLKIN |\ 524 HRCWL_VCO_1X4 |\ 525 HRCWL_CORE_TO_CSB_3X1) 526 #elif 0 /*264/132*/ 527 #define CONFIG_SYS_HRCW_LOW (\ 528 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 529 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 530 HRCWL_CSB_TO_CLKIN |\ 531 HRCWL_VCO_1X4 |\ 532 HRCWL_CORE_TO_CSB_2X1) 533 #elif 0 /*132/132*/ 534 #define CONFIG_SYS_HRCW_LOW (\ 535 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 536 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 537 HRCWL_CSB_TO_CLKIN |\ 538 HRCWL_VCO_1X4 |\ 539 HRCWL_CORE_TO_CSB_1X1) 540 #elif 0 /*264/264 */ 541 #define CONFIG_SYS_HRCW_LOW (\ 542 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 543 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 544 HRCWL_CSB_TO_CLKIN |\ 545 HRCWL_VCO_1X4 |\ 546 HRCWL_CORE_TO_CSB_1X1) 547 #endif 548 549 #ifdef CONFIG_PCISLAVE 550 #define CONFIG_SYS_HRCW_HIGH (\ 551 HRCWH_PCI_AGENT |\ 552 HRCWH_64_BIT_PCI |\ 553 HRCWH_PCI1_ARBITER_DISABLE |\ 554 HRCWH_PCI2_ARBITER_DISABLE |\ 555 HRCWH_CORE_ENABLE |\ 556 HRCWH_FROM_0X00000100 |\ 557 HRCWH_BOOTSEQ_DISABLE |\ 558 HRCWH_SW_WATCHDOG_DISABLE |\ 559 HRCWH_ROM_LOC_LOCAL_16BIT |\ 560 HRCWH_TSEC1M_IN_GMII |\ 561 HRCWH_TSEC2M_IN_GMII) 562 #else 563 #if defined(PCI_64BIT) 564 #define CONFIG_SYS_HRCW_HIGH (\ 565 HRCWH_PCI_HOST |\ 566 HRCWH_64_BIT_PCI |\ 567 HRCWH_PCI1_ARBITER_ENABLE |\ 568 HRCWH_PCI2_ARBITER_DISABLE |\ 569 HRCWH_CORE_ENABLE |\ 570 HRCWH_FROM_0X00000100 |\ 571 HRCWH_BOOTSEQ_DISABLE |\ 572 HRCWH_SW_WATCHDOG_DISABLE |\ 573 HRCWH_ROM_LOC_LOCAL_16BIT |\ 574 HRCWH_TSEC1M_IN_GMII |\ 575 HRCWH_TSEC2M_IN_GMII) 576 #else 577 #define CONFIG_SYS_HRCW_HIGH (\ 578 HRCWH_PCI_HOST |\ 579 HRCWH_32_BIT_PCI |\ 580 HRCWH_PCI1_ARBITER_ENABLE |\ 581 HRCWH_PCI2_ARBITER_ENABLE |\ 582 HRCWH_CORE_ENABLE |\ 583 HRCWH_FROM_0X00000100 |\ 584 HRCWH_BOOTSEQ_DISABLE |\ 585 HRCWH_SW_WATCHDOG_DISABLE |\ 586 HRCWH_ROM_LOC_LOCAL_16BIT |\ 587 HRCWH_TSEC1M_IN_GMII |\ 588 HRCWH_TSEC2M_IN_GMII) 589 #endif /* PCI_64BIT */ 590 #endif /* CONFIG_PCISLAVE */ 591 592 /* 593 * System performance 594 */ 595 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ 596 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ 597 #define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */ 598 #define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */ 599 #define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */ 600 #define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */ 601 602 /* System IO Config */ 603 #define CONFIG_SYS_SICRH 0 604 #define CONFIG_SYS_SICRL SICRL_LDP_A 605 606 #define CONFIG_SYS_HID0_INIT 0x000000000 607 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \ 608 | HID0_ENABLE_INSTRUCTION_CACHE) 609 610 /* #define CONFIG_SYS_HID0_FINAL (\ 611 HID0_ENABLE_INSTRUCTION_CACHE |\ 612 HID0_ENABLE_M_BIT |\ 613 HID0_ENABLE_ADDRESS_BROADCAST) */ 614 615 #define CONFIG_SYS_HID2 HID2_HBE 616 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 617 618 /* DDR @ 0x00000000 */ 619 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ 620 | BATL_PP_RW \ 621 | BATL_MEMCOHERENCE) 622 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ 623 | BATU_BL_256M \ 624 | BATU_VS \ 625 | BATU_VP) 626 627 /* PCI @ 0x80000000 */ 628 #ifdef CONFIG_PCI 629 #define CONFIG_PCI_INDIRECT_BRIDGE 630 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \ 631 | BATL_PP_RW \ 632 | BATL_MEMCOHERENCE) 633 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \ 634 | BATU_BL_256M \ 635 | BATU_VS \ 636 | BATU_VP) 637 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \ 638 | BATL_PP_RW \ 639 | BATL_CACHEINHIBIT \ 640 | BATL_GUARDEDSTORAGE) 641 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \ 642 | BATU_BL_256M \ 643 | BATU_VS \ 644 | BATU_VP) 645 #else 646 #define CONFIG_SYS_IBAT1L (0) 647 #define CONFIG_SYS_IBAT1U (0) 648 #define CONFIG_SYS_IBAT2L (0) 649 #define CONFIG_SYS_IBAT2U (0) 650 #endif 651 652 #ifdef CONFIG_MPC83XX_PCI2 653 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \ 654 | BATL_PP_RW \ 655 | BATL_MEMCOHERENCE) 656 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \ 657 | BATU_BL_256M \ 658 | BATU_VS \ 659 | BATU_VP) 660 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \ 661 | BATL_PP_RW \ 662 | BATL_CACHEINHIBIT \ 663 | BATL_GUARDEDSTORAGE) 664 #define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \ 665 | BATU_BL_256M \ 666 | BATU_VS \ 667 | BATU_VP) 668 #else 669 #define CONFIG_SYS_IBAT3L (0) 670 #define CONFIG_SYS_IBAT3U (0) 671 #define CONFIG_SYS_IBAT4L (0) 672 #define CONFIG_SYS_IBAT4U (0) 673 #endif 674 675 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ 676 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \ 677 | BATL_PP_RW \ 678 | BATL_CACHEINHIBIT \ 679 | BATL_GUARDEDSTORAGE) 680 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \ 681 | BATU_BL_256M \ 682 | BATU_VS \ 683 | BATU_VP) 684 685 /* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ 686 #define CONFIG_SYS_IBAT6L (0xF0000000 \ 687 | BATL_PP_RW \ 688 | BATL_MEMCOHERENCE \ 689 | BATL_GUARDEDSTORAGE) 690 #define CONFIG_SYS_IBAT6U (0xF0000000 \ 691 | BATU_BL_256M \ 692 | BATU_VS \ 693 | BATU_VP) 694 695 #define CONFIG_SYS_IBAT7L (0) 696 #define CONFIG_SYS_IBAT7U (0) 697 698 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 699 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 700 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 701 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 702 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 703 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 704 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 705 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 706 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 707 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 708 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 709 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 710 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 711 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 712 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 713 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 714 715 #if defined(CONFIG_CMD_KGDB) 716 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 717 #endif 718 719 /* 720 * Environment Configuration 721 */ 722 #define CONFIG_ENV_OVERWRITE 723 724 #if defined(CONFIG_TSEC_ENET) 725 #define CONFIG_HAS_ETH1 726 #define CONFIG_HAS_ETH0 727 #endif 728 729 #define CONFIG_HOSTNAME mpc8349emds 730 #define CONFIG_ROOTPATH "/nfsroot/rootfs" 731 #define CONFIG_BOOTFILE "uImage" 732 733 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 734 735 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 736 737 #define CONFIG_BAUDRATE 115200 738 739 #define CONFIG_PREBOOT "echo;" \ 740 "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ 741 "echo" 742 743 #define CONFIG_EXTRA_ENV_SETTINGS \ 744 "netdev=eth0\0" \ 745 "hostname=mpc8349emds\0" \ 746 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 747 "nfsroot=${serverip}:${rootpath}\0" \ 748 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 749 "addip=setenv bootargs ${bootargs} " \ 750 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 751 ":${hostname}:${netdev}:off panic=1\0" \ 752 "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ 753 "flash_nfs=run nfsargs addip addtty;" \ 754 "bootm ${kernel_addr}\0" \ 755 "flash_self=run ramargs addip addtty;" \ 756 "bootm ${kernel_addr} ${ramdisk_addr}\0" \ 757 "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ 758 "bootm\0" \ 759 "load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0" \ 760 "update=protect off fe000000 fe03ffff; " \ 761 "era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\ 762 "upd=run load update\0" \ 763 "fdtaddr=780000\0" \ 764 "fdtfile=mpc834x_mds.dtb\0" \ 765 "" 766 767 #define CONFIG_NFSBOOTCOMMAND \ 768 "setenv bootargs root=/dev/nfs rw " \ 769 "nfsroot=$serverip:$rootpath " \ 770 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ 771 "$netdev:off " \ 772 "console=$consoledev,$baudrate $othbootargs;" \ 773 "tftp $loadaddr $bootfile;" \ 774 "tftp $fdtaddr $fdtfile;" \ 775 "bootm $loadaddr - $fdtaddr" 776 777 #define CONFIG_RAMBOOTCOMMAND \ 778 "setenv bootargs root=/dev/ram rw " \ 779 "console=$consoledev,$baudrate $othbootargs;" \ 780 "tftp $ramdiskaddr $ramdiskfile;" \ 781 "tftp $loadaddr $bootfile;" \ 782 "tftp $fdtaddr $fdtfile;" \ 783 "bootm $loadaddr $ramdiskaddr $fdtaddr" 784 785 #define CONFIG_BOOTCOMMAND "run flash_self" 786 787 #endif /* __CONFIG_H */ 788