1 /* 2 * Copyright (C) Freescale Semiconductor, Inc. 2006, 2010. 3 * 4 * See file CREDITS for list of people who contributed to this 5 * project. 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License as 9 * published by the Free Software Foundation; either version 2 of 10 * the License, or (at your option) any later version. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 20 * MA 02111-1307 USA 21 */ 22 /* 23 * mpc8313epb board configuration file 24 */ 25 26 #ifndef __CONFIG_H 27 #define __CONFIG_H 28 29 /* 30 * High Level Configuration Options 31 */ 32 #define CONFIG_E300 1 33 #define CONFIG_MPC83xx 1 34 #define CONFIG_MPC831x 1 35 #define CONFIG_MPC8313 1 36 #define CONFIG_MPC8313ERDB 1 37 38 #define CONFIG_PCI 39 #define CONFIG_FSL_ELBC 1 40 41 #define CONFIG_MISC_INIT_R 42 43 /* 44 * On-board devices 45 * 46 * TSEC1 is VSC switch 47 * TSEC2 is SoC TSEC 48 */ 49 #define CONFIG_VSC7385_ENET 50 #define CONFIG_TSEC2 51 52 #ifdef CONFIG_SYS_66MHZ 53 #define CONFIG_83XX_CLKIN 66666667 /* in Hz */ 54 #elif defined(CONFIG_SYS_33MHZ) 55 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ 56 #else 57 #error Unknown oscillator frequency. 58 #endif 59 60 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 61 62 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ 63 64 #define CONFIG_SYS_IMMR 0xE0000000 65 66 #if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) 67 #define CONFIG_DEFAULT_IMMR CONFIG_SYS_IMMR 68 #endif 69 70 #define CONFIG_SYS_MEMTEST_START 0x00001000 71 #define CONFIG_SYS_MEMTEST_END 0x07f00000 72 73 /* Early revs of this board will lock up hard when attempting 74 * to access the PMC registers, unless a JTAG debugger is 75 * connected, or some resistor modifications are made. 76 */ 77 #define CONFIG_SYS_8313ERDB_BROKEN_PMC 1 78 79 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ 80 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ 81 82 /* 83 * Device configurations 84 */ 85 86 /* Vitesse 7385 */ 87 88 #ifdef CONFIG_VSC7385_ENET 89 90 #define CONFIG_TSEC1 91 92 /* The flash address and size of the VSC7385 firmware image */ 93 #define CONFIG_VSC7385_IMAGE 0xFE7FE000 94 #define CONFIG_VSC7385_IMAGE_SIZE 8192 95 96 #endif 97 98 /* 99 * DDR Setup 100 */ 101 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/ 102 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 103 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 104 105 /* 106 * Manually set up DDR parameters, as this board does not 107 * seem to have the SPD connected to I2C. 108 */ 109 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 110 #define CONFIG_SYS_DDR_CONFIG ( CSCONFIG_EN \ 111 | 0x00010000 /* TODO */ \ 112 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 ) 113 /* 0x80010102 */ 114 115 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 116 #define CONFIG_SYS_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ 117 | ( 0 << TIMING_CFG0_WRT_SHIFT ) \ 118 | ( 0 << TIMING_CFG0_RRT_SHIFT ) \ 119 | ( 0 << TIMING_CFG0_WWT_SHIFT ) \ 120 | ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \ 121 | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \ 122 | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \ 123 | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) ) 124 /* 0x00220802 */ 125 #define CONFIG_SYS_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \ 126 | ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT ) \ 127 | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \ 128 | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \ 129 | (10 << TIMING_CFG1_REFREC_SHIFT ) \ 130 | ( 3 << TIMING_CFG1_WRREC_SHIFT ) \ 131 | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \ 132 | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) ) 133 /* 0x3835a322 */ 134 #define CONFIG_SYS_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \ 135 | ( 5 << TIMING_CFG2_CPO_SHIFT ) \ 136 | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \ 137 | ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \ 138 | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \ 139 | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \ 140 | ( 6 << TIMING_CFG2_FOUR_ACT_SHIFT) ) 141 /* 0x129048c6 */ /* P9-45,may need tuning */ 142 #define CONFIG_SYS_DDR_INTERVAL ( ( 1296 << SDRAM_INTERVAL_REFINT_SHIFT ) \ 143 | ( 1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) ) 144 /* 0x05100500 */ 145 #if defined(CONFIG_DDR_2T_TIMING) 146 #define CONFIG_SYS_SDRAM_CFG ( SDRAM_CFG_SREN \ 147 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 148 | SDRAM_CFG_2T_EN \ 149 | SDRAM_CFG_DBW_32 ) 150 #else 151 #define CONFIG_SYS_SDRAM_CFG ( SDRAM_CFG_SREN \ 152 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 153 | SDRAM_CFG_32_BE ) 154 /* 0x43080000 */ 155 #endif 156 #define CONFIG_SYS_SDRAM_CFG2 0x00401000 157 /* set burst length to 8 for 32-bit data path */ 158 #define CONFIG_SYS_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \ 159 | ( 0x0632 << SDRAM_MODE_SD_SHIFT ) ) 160 /* 0x44480632 */ 161 #define CONFIG_SYS_DDR_MODE_2 0x8000C000 162 163 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 164 /*0x02000000*/ 165 #define CONFIG_SYS_DDRCDR_VALUE ( DDRCDR_EN \ 166 | DDRCDR_PZ_NOMZ \ 167 | DDRCDR_NZ_NOMZ \ 168 | DDRCDR_M_ODR ) 169 170 /* 171 * FLASH on the Local Bus 172 */ 173 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 174 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 175 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */ 176 #define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */ 177 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 178 #define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */ 179 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */ 180 181 #define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE | /* flash Base address */ \ 182 (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ 183 BR_V) /* valid */ 184 #define CONFIG_SYS_NOR_OR_PRELIM ( 0xFF800000 /* 8 MByte */ \ 185 | OR_GPCM_XACS \ 186 | OR_GPCM_SCY_9 \ 187 | OR_GPCM_EHTR \ 188 | OR_GPCM_EAD ) 189 /* 0xFF006FF7 TODO SLOW 16 MB flash size */ 190 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* window base at flash base */ 191 #define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000017 /* 16 MB window size */ 192 193 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 194 #define CONFIG_SYS_MAX_FLASH_SECT 135 /* sectors per device */ 195 196 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 197 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 198 199 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 200 201 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) && !defined(CONFIG_NAND_SPL) 202 #define CONFIG_SYS_RAMBOOT 203 #endif 204 205 #define CONFIG_SYS_INIT_RAM_LOCK 1 206 #define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ 207 #define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM*/ 208 209 #define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ 210 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 211 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 212 213 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ 214 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 215 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 216 217 /* 218 * Local Bus LCRR and LBCR regs 219 */ 220 #define CONFIG_SYS_LCRR_EADC LCRR_EADC_1 221 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 222 #define CONFIG_SYS_LBC_LBCR ( 0x00040000 /* TODO */ \ 223 | (0xFF << LBCR_BMT_SHIFT) \ 224 | 0xF ) /* 0x0004ff0f */ 225 226 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */ 227 228 /* drivers/mtd/nand/nand.c */ 229 #ifdef CONFIG_NAND_SPL 230 #define CONFIG_SYS_NAND_BASE 0xFFF00000 231 #else 232 #define CONFIG_SYS_NAND_BASE 0xE2800000 233 #endif 234 235 #define CONFIG_MTD_DEVICE 236 #define CONFIG_MTD_PARTITION 237 #define CONFIG_CMD_MTDPARTS 238 #define MTDIDS_DEFAULT "nand0=e2800000.flash" 239 #define MTDPARTS_DEFAULT \ 240 "mtdparts=e0600000.flash:512k(uboot),128k(env),3m@1m(kernel),-(fs)" 241 242 #define CONFIG_SYS_MAX_NAND_DEVICE 1 243 #define CONFIG_MTD_NAND_VERIFY_WRITE 244 #define CONFIG_CMD_NAND 1 245 #define CONFIG_NAND_FSL_ELBC 1 246 #define CONFIG_SYS_NAND_BLOCK_SIZE 16384 247 248 #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) 249 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 250 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 251 #define CONFIG_SYS_NAND_U_BOOT_OFFS 16384 252 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 253 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000) 254 255 #define CONFIG_SYS_NAND_BR_PRELIM ( CONFIG_SYS_NAND_BASE \ 256 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 257 | BR_PS_8 /* Port Size = 8 bit */ \ 258 | BR_MS_FCM /* MSEL = FCM */ \ 259 | BR_V ) /* valid */ 260 #define CONFIG_SYS_NAND_OR_PRELIM ( 0xFFFF8000 /* length 32K */ \ 261 | OR_FCM_CSCT \ 262 | OR_FCM_CST \ 263 | OR_FCM_CHT \ 264 | OR_FCM_SCY_1 \ 265 | OR_FCM_TRLX \ 266 | OR_FCM_EHTR ) 267 /* 0xFFFF8396 */ 268 269 #ifdef CONFIG_NAND_U_BOOT 270 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM 271 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM 272 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NOR_BR_PRELIM 273 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NOR_OR_PRELIM 274 #else 275 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM 276 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM 277 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM 278 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM 279 #endif 280 281 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE 282 #define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */ 283 284 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM 285 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM 286 287 /* local bus read write buffer mapping */ 288 #define CONFIG_SYS_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */ 289 #define CONFIG_SYS_OR3_PRELIM 0xFFFF8FF7 /* 32kB */ 290 #define CONFIG_SYS_LBLAWBAR3_PRELIM 0xFA000000 291 #define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000E /* 32KB */ 292 293 /* Vitesse 7385 */ 294 295 #define CONFIG_SYS_VSC7385_BASE 0xF0000000 296 297 #ifdef CONFIG_VSC7385_ENET 298 299 #define CONFIG_SYS_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */ 300 #define CONFIG_SYS_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/ 301 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE/* Access window base at VSC7385 base */ 302 #define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* Access window size 128K */ 303 304 #endif 305 306 /* pass open firmware flat tree */ 307 #define CONFIG_OF_LIBFDT 1 308 #define CONFIG_OF_BOARD_SETUP 1 309 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 310 311 /* 312 * Serial Port 313 */ 314 #define CONFIG_CONS_INDEX 1 315 #define CONFIG_SYS_NS16550 316 #define CONFIG_SYS_NS16550_SERIAL 317 #define CONFIG_SYS_NS16550_REG_SIZE 1 318 319 #define CONFIG_SYS_BAUDRATE_TABLE \ 320 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 321 322 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 323 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 324 325 /* Use the HUSH parser */ 326 #define CONFIG_SYS_HUSH_PARSER 327 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 328 329 /* I2C */ 330 #define CONFIG_HARD_I2C /* I2C with hardware support*/ 331 #define CONFIG_FSL_I2C 332 #define CONFIG_I2C_MULTI_BUS 333 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 334 #define CONFIG_SYS_I2C_SLAVE 0x7F 335 #define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ 336 #define CONFIG_SYS_I2C_OFFSET 0x3000 337 #define CONFIG_SYS_I2C2_OFFSET 0x3100 338 339 /* 340 * General PCI 341 * Addresses are mapped 1-1. 342 */ 343 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 344 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 345 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 346 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 347 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE 348 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ 349 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 350 #define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 351 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ 352 353 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 354 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ 355 356 /* 357 * TSEC 358 */ 359 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 360 361 #define CONFIG_NET_MULTI 362 #define CONFIG_GMII /* MII PHY management */ 363 364 #ifdef CONFIG_TSEC1 365 #define CONFIG_HAS_ETH0 366 #define CONFIG_TSEC1_NAME "TSEC0" 367 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 368 #define TSEC1_PHY_ADDR 0x1c 369 #define TSEC1_FLAGS TSEC_GIGABIT 370 #define TSEC1_PHYIDX 0 371 #endif 372 373 #ifdef CONFIG_TSEC2 374 #define CONFIG_HAS_ETH1 375 #define CONFIG_TSEC2_NAME "TSEC1" 376 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 377 #define TSEC2_PHY_ADDR 4 378 #define TSEC2_FLAGS TSEC_GIGABIT 379 #define TSEC2_PHYIDX 0 380 #endif 381 382 383 /* Options are: TSEC[0-1] */ 384 #define CONFIG_ETHPRIME "TSEC1" 385 386 /* 387 * Configure on-board RTC 388 */ 389 #define CONFIG_RTC_DS1337 390 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 391 392 /* 393 * Environment 394 */ 395 #if defined(CONFIG_NAND_U_BOOT) 396 #define CONFIG_ENV_IS_IN_NAND 1 397 #define CONFIG_ENV_OFFSET (512 * 1024) 398 #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 399 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE 400 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 401 #define CONFIG_ENV_RANGE (CONFIG_ENV_SECT_SIZE * 4) 402 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE) 403 #elif !defined(CONFIG_SYS_RAMBOOT) 404 #define CONFIG_ENV_IS_IN_FLASH 1 405 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 406 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 407 #define CONFIG_ENV_SIZE 0x2000 408 409 /* Address and size of Redundant Environment Sector */ 410 #else 411 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 412 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 413 #define CONFIG_ENV_SIZE 0x2000 414 #endif 415 416 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 417 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 418 419 /* 420 * BOOTP options 421 */ 422 #define CONFIG_BOOTP_BOOTFILESIZE 423 #define CONFIG_BOOTP_BOOTPATH 424 #define CONFIG_BOOTP_GATEWAY 425 #define CONFIG_BOOTP_HOSTNAME 426 427 428 /* 429 * Command line configuration. 430 */ 431 #include <config_cmd_default.h> 432 433 #define CONFIG_CMD_PING 434 #define CONFIG_CMD_DHCP 435 #define CONFIG_CMD_I2C 436 #define CONFIG_CMD_MII 437 #define CONFIG_CMD_DATE 438 #define CONFIG_CMD_PCI 439 440 #if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT) 441 #undef CONFIG_CMD_SAVEENV 442 #undef CONFIG_CMD_LOADS 443 #endif 444 445 #define CONFIG_CMDLINE_EDITING 1 446 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 447 448 /* 449 * Miscellaneous configurable options 450 */ 451 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 452 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 453 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 454 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 455 456 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 457 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 458 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 459 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 460 461 /* 462 * For booting Linux, the board info and command line data 463 * have to be in the first 256 MB of memory, since this is 464 * the maximum mapped by the Linux kernel during initialization. 465 */ 466 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ 467 468 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ 469 470 #ifdef CONFIG_SYS_66MHZ 471 472 /* 66MHz IN, 133MHz CSB, 266 DDR, 266 CORE */ 473 /* 0x62040000 */ 474 #define CONFIG_SYS_HRCW_LOW (\ 475 0x20000000 /* reserved, must be set */ |\ 476 HRCWL_DDRCM |\ 477 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 478 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 479 HRCWL_CSB_TO_CLKIN_2X1 |\ 480 HRCWL_CORE_TO_CSB_2X1) 481 482 #define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2) 483 484 #elif defined(CONFIG_SYS_33MHZ) 485 486 /* 33MHz IN, 165MHz CSB, 330 DDR, 330 CORE */ 487 /* 0x65040000 */ 488 #define CONFIG_SYS_HRCW_LOW (\ 489 0x20000000 /* reserved, must be set */ |\ 490 HRCWL_DDRCM |\ 491 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 492 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 493 HRCWL_CSB_TO_CLKIN_5X1 |\ 494 HRCWL_CORE_TO_CSB_2X1) 495 496 #define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 5) 497 498 #endif 499 500 #define CONFIG_SYS_HRCW_HIGH_BASE (\ 501 HRCWH_PCI_HOST |\ 502 HRCWH_PCI1_ARBITER_ENABLE |\ 503 HRCWH_CORE_ENABLE |\ 504 HRCWH_BOOTSEQ_DISABLE |\ 505 HRCWH_SW_WATCHDOG_DISABLE |\ 506 HRCWH_TSEC1M_IN_RGMII |\ 507 HRCWH_TSEC2M_IN_RGMII |\ 508 HRCWH_BIG_ENDIAN) 509 510 #ifdef CONFIG_NAND_SPL 511 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\ 512 HRCWH_FROM_0XFFF00100 |\ 513 HRCWH_ROM_LOC_NAND_SP_8BIT |\ 514 HRCWH_RL_EXT_NAND) 515 #else 516 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\ 517 HRCWH_FROM_0X00000100 |\ 518 HRCWH_ROM_LOC_LOCAL_16BIT |\ 519 HRCWH_RL_EXT_LEGACY) 520 #endif 521 522 /* System IO Config */ 523 #define CONFIG_SYS_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */ 524 #define CONFIG_SYS_SICRL SICRL_USBDR_10 /* Enable Internal USB Phy */ 525 526 #define CONFIG_SYS_HID0_INIT 0x000000000 527 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 528 HID0_ENABLE_INSTRUCTION_CACHE | \ 529 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 530 531 #define CONFIG_SYS_HID2 HID2_HBE 532 533 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 534 535 /* DDR @ 0x00000000 */ 536 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10) 537 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) 538 539 /* PCI @ 0x80000000 */ 540 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10) 541 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) 542 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 543 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP) 544 545 /* PCI2 not supported on 8313 */ 546 #define CONFIG_SYS_IBAT3L (0) 547 #define CONFIG_SYS_IBAT3U (0) 548 #define CONFIG_SYS_IBAT4L (0) 549 #define CONFIG_SYS_IBAT4U (0) 550 551 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ 552 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 553 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP) 554 555 /* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ 556 #define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE) 557 #define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) 558 559 #define CONFIG_SYS_IBAT7L (0) 560 #define CONFIG_SYS_IBAT7U (0) 561 562 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 563 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 564 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 565 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 566 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 567 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 568 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 569 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 570 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 571 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 572 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 573 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 574 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 575 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 576 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 577 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 578 579 /* 580 * Internal Definitions 581 * 582 * Boot Flags 583 */ 584 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 585 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 586 587 /* 588 * Environment Configuration 589 */ 590 #define CONFIG_ENV_OVERWRITE 591 592 #define CONFIG_NETDEV eth1 593 594 #define CONFIG_HOSTNAME mpc8313erdb 595 #define CONFIG_ROOTPATH /nfs/root/path 596 #define CONFIG_BOOTFILE uImage 597 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 598 #define CONFIG_FDTFILE mpc8313erdb.dtb 599 600 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 601 #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ 602 #define CONFIG_BAUDRATE 115200 603 604 #define XMK_STR(x) #x 605 #define MK_STR(x) XMK_STR(x) 606 607 #define CONFIG_EXTRA_ENV_SETTINGS \ 608 "netdev=" MK_STR(CONFIG_NETDEV) "\0" \ 609 "ethprime=TSEC1\0" \ 610 "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ 611 "tftpflash=tftpboot $loadaddr $uboot; " \ 612 "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 613 "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 614 "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; " \ 615 "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 616 "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0" \ 617 "fdtaddr=780000\0" \ 618 "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \ 619 "console=ttyS0\0" \ 620 "setbootargs=setenv bootargs " \ 621 "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \ 622 "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \ 623 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 624 "root=$rootdev rw console=$console,$baudrate $othbootargs\0" 625 626 #define CONFIG_NFSBOOTCOMMAND \ 627 "setenv rootdev /dev/nfs;" \ 628 "run setbootargs;" \ 629 "run setipargs;" \ 630 "tftp $loadaddr $bootfile;" \ 631 "tftp $fdtaddr $fdtfile;" \ 632 "bootm $loadaddr - $fdtaddr" 633 634 #define CONFIG_RAMBOOTCOMMAND \ 635 "setenv rootdev /dev/ram;" \ 636 "run setbootargs;" \ 637 "tftp $ramdiskaddr $ramdiskfile;" \ 638 "tftp $loadaddr $bootfile;" \ 639 "tftp $fdtaddr $fdtfile;" \ 640 "bootm $loadaddr $ramdiskaddr $fdtaddr" 641 642 #undef MK_STR 643 #undef XMK_STR 644 645 #endif /* __CONFIG_H */ 646