1 /* 2 * Configuation settings for the Freescale MCF54418 TWR board. 3 * 4 * Copyright 2010-2012 Freescale Semiconductor, Inc. 5 * TsiChung Liew (Tsi-Chung.Liew@freescale.com) 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 /* 11 * board/config.h - configuration options, board specific 12 */ 13 14 #ifndef _M54418TWR_H 15 #define _M54418TWR_H 16 17 /* 18 * High Level Configuration Options 19 * (easy to change) 20 */ 21 #define CONFIG_M54418TWR /* M54418TWR board */ 22 23 #define CONFIG_MCFUART 24 #define CONFIG_SYS_UART_PORT (0) 25 #define CONFIG_BAUDRATE 115200 26 #define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } 27 28 #undef CONFIG_WATCHDOG 29 30 #define CONFIG_TIMESTAMP /* Print image info with timestamp */ 31 32 /* 33 * BOOTP options 34 */ 35 #define CONFIG_BOOTP_BOOTFILESIZE 36 #define CONFIG_BOOTP_BOOTPATH 37 #define CONFIG_BOOTP_GATEWAY 38 #define CONFIG_BOOTP_HOSTNAME 39 40 /* Command line configuration */ 41 #define CONFIG_CMD_CACHE 42 #undef CONFIG_CMD_DATE 43 #define CONFIG_CMD_DHCP 44 #undef CONFIG_CMD_I2C 45 #undef CONFIG_CMD_JFFS2 46 #undef CONFIG_CMD_UBI 47 #define CONFIG_CMD_MII 48 #undef CONFIG_CMD_NAND 49 #define CONFIG_CMD_PING 50 #define CONFIG_CMD_REGINFO 51 #define CONFIG_CMD_SPI 52 #define CONFIG_CMD_SF 53 54 55 /* 56 * NAND FLASH 57 */ 58 #ifdef CONFIG_CMD_NAND 59 #define CONFIG_JFFS2_NAND 60 #define CONFIG_NAND_FSL_NFC 61 #define CONFIG_SYS_NAND_BASE 0xFC0FC000 62 #define CONFIG_SYS_MAX_NAND_DEVICE 1 63 #define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE 64 #define CONFIG_SYS_NAND_SELECT_DEVICE 65 #endif 66 67 /* Network configuration */ 68 #define CONFIG_MCFFEC 69 #ifdef CONFIG_MCFFEC 70 #define CONFIG_MII 1 71 #define CONFIG_MII_INIT 1 72 #define CONFIG_SYS_DISCOVER_PHY 73 #define CONFIG_SYS_RX_ETH_BUFFER 2 74 #define CONFIG_SYS_FAULT_ECCONFIG_SYS_NO_FLASHHO_LINK_DOWN 75 #define CONFIG_SYS_TX_ETH_BUFFER 2 76 #define CONFIG_HAS_ETH1 77 78 #define CONFIG_SYS_FEC0_PINMUX 0 79 #define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 80 #define CONFIG_SYS_FEC1_PINMUX 0 81 #define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_MIIBASE 82 #define MCFFEC_TOUT_LOOP 50000 83 #define CONFIG_SYS_FEC0_PHYADDR 0 84 #define CONFIG_SYS_FEC1_PHYADDR 1 85 86 #define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */ 87 88 #ifdef CONFIG_SYS_NAND_BOOT 89 #define CONFIG_BOOTARGS "root=/dev/mtdblock2 rw rootfstype=jffs2 " \ 90 "mtdparts=NAND:1M(u-boot)ro,7M(kernel)ro," \ 91 "-(jffs2) console=ttyS0,115200" 92 #else 93 #define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=" \ 94 __stringify(CONFIG_SERVERIP) ":/tftpboot/" \ 95 __stringify(CONFIG_IPADDR) " ip=" \ 96 __stringify(CONFIG_IPADDR) ":" \ 97 __stringify(CONFIG_SERVERIP)":" \ 98 __stringify(CONFIG_GATEWAYIP)": " \ 99 __stringify(CONFIG_NETMASK) \ 100 "::eth0:off:rw console=ttyS0,115200" 101 #endif 102 103 #define CONFIG_ETHPRIME "FEC0" 104 #define CONFIG_IPADDR 192.168.1.2 105 #define CONFIG_NETMASK 255.255.255.0 106 #define CONFIG_SERVERIP 192.168.1.1 107 #define CONFIG_GATEWAYIP 192.168.1.1 108 109 #define CONFIG_SYS_FEC_BUF_USE_SRAM 110 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 111 #ifndef CONFIG_SYS_DISCOVER_PHY 112 #define FECDUPLEX FULL 113 #define FECSPEED _100BASET 114 #define LINKSTATUS 1 115 #else 116 #define LINKSTATUS 0 117 #ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 118 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 119 #endif 120 #endif /* CONFIG_SYS_DISCOVER_PHY */ 121 #endif 122 123 #define CONFIG_HOSTNAME M54418TWR 124 125 #if defined(CONFIG_CF_SBF) 126 /* ST Micro serial flash */ 127 #define CONFIG_SYS_LOAD_ADDR2 0x40010007 128 #define CONFIG_EXTRA_ENV_SETTINGS \ 129 "netdev=eth0\0" \ 130 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ 131 "loadaddr=0x40010000\0" \ 132 "sbfhdr=sbfhdr.bin\0" \ 133 "uboot=u-boot.bin\0" \ 134 "load=tftp ${loadaddr} ${sbfhdr};" \ 135 "tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0" \ 136 "upd=run load; run prog\0" \ 137 "prog=sf probe 0:1 1000000 3;" \ 138 "sf erase 0 40000;" \ 139 "sf write ${loadaddr} 0 40000;" \ 140 "save\0" \ 141 "" 142 #elif defined(CONFIG_SYS_NAND_BOOT) 143 #define CONFIG_EXTRA_ENV_SETTINGS \ 144 "netdev=eth0\0" \ 145 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ 146 "loadaddr=0x40010000\0" \ 147 "u-boot=u-boot.bin\0" \ 148 "load=tftp ${loadaddr} ${u-boot};\0" \ 149 "upd=run load; run prog\0" \ 150 "prog=nand device 0;" \ 151 "nand erase 0 40000;" \ 152 "nb_update ${loadaddr} ${filesize};" \ 153 "save\0" \ 154 "" 155 #else 156 #define CONFIG_SYS_UBOOT_END 0x3FFFF 157 #define CONFIG_EXTRA_ENV_SETTINGS \ 158 "netdev=eth0\0" \ 159 "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ 160 "loadaddr=40010000\0" \ 161 "u-boot=u-boot.bin\0" \ 162 "load=tftp ${loadaddr) ${u-boot}\0" \ 163 "upd=run load; run prog\0" \ 164 "prog=prot off mram" " ;" \ 165 "cp.b ${loadaddr} 0 ${filesize};" \ 166 "save\0" \ 167 "" 168 #endif 169 170 /* Realtime clock */ 171 #undef CONFIG_MCFRTC 172 #define CONFIG_RTC_MCFRRTC 173 #define CONFIG_SYS_MCFRRTC_BASE 0xFC0A8000 174 175 /* Timer */ 176 #define CONFIG_MCFTMR 177 #undef CONFIG_MCFPIT 178 179 /* I2c */ 180 #undef CONFIG_SYS_FSL_I2C 181 #undef CONFIG_HARD_I2C /* I2C with hardware support */ 182 #undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ 183 /* I2C speed and slave address */ 184 #define CONFIG_SYS_I2C_SPEED 80000 185 #define CONFIG_SYS_I2C_SLAVE 0x7F 186 #define CONFIG_SYS_I2C_OFFSET 0x58000 187 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 188 189 /* DSPI and Serial Flash */ 190 #define CONFIG_CF_SPI 191 #define CONFIG_CF_DSPI 192 #define CONFIG_SERIAL_FLASH 193 #define CONFIG_HARD_SPI 194 #define CONFIG_SYS_SBFHDR_SIZE 0x7 195 #ifdef CONFIG_CMD_SPI 196 197 # define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \ 198 DSPI_CTAR_PCSSCK_1CLK | \ 199 DSPI_CTAR_PASC(0) | \ 200 DSPI_CTAR_PDT(0) | \ 201 DSPI_CTAR_CSSCK(0) | \ 202 DSPI_CTAR_ASC(0) | \ 203 DSPI_CTAR_DT(1)) 204 # define CONFIG_SYS_DSPI_CTAR1 (CONFIG_SYS_DSPI_CTAR0) 205 # define CONFIG_SYS_DSPI_CTAR2 (CONFIG_SYS_DSPI_CTAR0) 206 #endif 207 208 /* Input, PCI, Flexbus, and VCO */ 209 #define CONFIG_EXTRA_CLOCK 210 211 #define CONFIG_PRAM 2048 /* 2048 KB */ 212 213 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 214 215 #if defined(CONFIG_CMD_KGDB) 216 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 217 #else 218 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 219 #endif 220 /* Print Buffer Size */ 221 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 222 sizeof(CONFIG_SYS_PROMPT) + 16) 223 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 224 /* Boot Argument Buffer Size */ 225 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 226 227 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000) 228 229 #define CONFIG_SYS_MBAR 0xFC000000 230 231 /* 232 * Low Level Configuration Settings 233 * (address mappings, register initial values, etc.) 234 * You should know what you are doing if you make changes here. 235 */ 236 237 /*----------------------------------------------------------------------- 238 * Definitions for initial stack pointer and data area (in DPRAM) 239 */ 240 #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 241 /* End of used area in internal SRAM */ 242 #define CONFIG_SYS_INIT_RAM_SIZE 0x10000 243 #define CONFIG_SYS_INIT_RAM_CTRL 0x221 244 #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - \ 245 GENERATED_GBL_DATA_SIZE) - 32) 246 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 247 #define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32) 248 249 /*----------------------------------------------------------------------- 250 * Start addresses for the final memory configuration 251 * (Set up by the startup code) 252 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 253 */ 254 #define CONFIG_SYS_SDRAM_BASE 0x40000000 255 #define CONFIG_SYS_SDRAM_SIZE 128 /* SDRAM size in MB */ 256 257 #define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x400) 258 #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) 259 #define CONFIG_SYS_DRAM_TEST 260 261 #if defined(CONFIG_CF_SBF) || defined(CONFIG_SYS_NAND_BOOT) 262 #define CONFIG_SERIAL_BOOT 263 #endif 264 265 #if defined(CONFIG_SERIAL_BOOT) 266 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400) 267 #else 268 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 269 #endif 270 271 #define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024) 272 /* Reserve 256 kB for Monitor */ 273 #define CONFIG_SYS_MONITOR_LEN (256 << 10) 274 /* Reserve 256 kB for malloc() */ 275 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 276 277 /* 278 * For booting Linux, the board info and command line data 279 * have to be in the first 8 MB of memory, since this is 280 * the maximum mapped by the Linux kernel during initialization ?? 281 */ 282 /* Initial Memory map for Linux */ 283 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \ 284 (CONFIG_SYS_SDRAM_SIZE << 20)) 285 286 /* Configuration for environment 287 * Environment is embedded in u-boot in the second sector of the flash 288 */ 289 #if !defined(CONFIG_SERIAL_BOOT) /*MRAM boot*/ 290 #define CONFIG_SYS_NO_FLASH 291 #define CONFIG_ENV_IS_IN_MRAM 1 292 #define CONFIG_ENV_ADDR (0x40000 - 0x1000) /*MRAM size 40000*/ 293 #define CONFIG_ENV_SIZE 0x1000 294 #endif 295 296 #if defined(CONFIG_CF_SBF) 297 #define CONFIG_SYS_NO_FLASH 298 #define CONFIG_ENV_IS_IN_SPI_FLASH 1 299 #define CONFIG_ENV_SPI_CS 1 300 #define CONFIG_ENV_OFFSET 0x40000 301 #define CONFIG_ENV_SIZE 0x2000 302 #define CONFIG_ENV_SECT_SIZE 0x10000 303 #endif 304 #if defined(CONFIG_SYS_NAND_BOOT) 305 #define CONFIG_SYS_NO_FLASH 306 #define CONFIG_ENV_IS_NOWHERE 307 #define CONFIG_ENV_OFFSET 0x80000 308 #define CONFIG_ENV_SIZE 0x20000 309 #define CONFIG_ENV_SECT_SIZE 0x20000 310 #endif 311 #undef CONFIG_ENV_OVERWRITE 312 313 /* FLASH organization */ 314 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE 315 316 #undef CONFIG_SYS_FLASH_CFI 317 #ifdef CONFIG_SYS_FLASH_CFI 318 319 #define CONFIG_FLASH_CFI_DRIVER 1 320 /* Max size that the board might have */ 321 #define CONFIG_SYS_FLASH_SIZE 0x1000000 322 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 323 /* max number of memory banks */ 324 #define CONFIG_SYS_MAX_FLASH_BANKS 1 325 /* max number of sectors on one chip */ 326 #define CONFIG_SYS_MAX_FLASH_SECT 270 327 /* "Real" (hardware) sectors protection */ 328 #define CONFIG_SYS_FLASH_PROTECTION 329 #define CONFIG_SYS_FLASH_CHECKSUM 330 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE } 331 #else 332 /* max number of sectors on one chip */ 333 #define CONFIG_SYS_MAX_FLASH_SECT 270 334 /* max number of sectors on one chip */ 335 #define CONFIG_SYS_MAX_FLASH_BANKS 0 336 #endif 337 338 /* 339 * This is setting for JFFS2 support in u-boot. 340 * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support. 341 */ 342 #ifdef CONFIG_CMD_JFFS2 343 #define CONFIG_JFFS2_DEV "nand0" 344 #define CONFIG_JFFS2_PART_OFFSET (0x800000) 345 #define CONFIG_CMD_MTDPARTS 346 #define CONFIG_MTD_DEVICE 347 #define MTDIDS_DEFAULT "nand0=m54418twr.nand" 348 349 #define MTDPARTS_DEFAULT "mtdparts=m54418twr.nand:1m(data)," \ 350 "7m(kernel)," \ 351 "-(rootfs)" 352 353 #endif 354 355 #ifdef CONFIG_CMD_UBI 356 #define CONFIG_CMD_MTDPARTS 357 #define CONFIG_MTD_DEVICE /* needed for mtdparts command */ 358 #define CONFIG_MTD_PARTITIONS /* mtdparts and UBI support */ 359 #define CONFIG_RBTREE 360 #define MTDIDS_DEFAULT "nand0=NAND" 361 #define MTDPARTS_DEFAULT "mtdparts=NAND:1m(u-boot)," \ 362 "-(ubi)" 363 #endif 364 /* Cache Configuration */ 365 #define CONFIG_SYS_CACHELINE_SIZE 16 366 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 367 CONFIG_SYS_INIT_RAM_SIZE - 8) 368 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 369 CONFIG_SYS_INIT_RAM_SIZE - 4) 370 #define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) 371 #define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) 372 #define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ 373 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 374 CF_ACR_EN | CF_ACR_SM_ALL) 375 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ 376 CF_CACR_ICINVA | CF_CACR_EUSP) 377 #define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ 378 CF_CACR_DEC | CF_CACR_DDCM_P | \ 379 CF_CACR_DCINVA) & ~CF_CACR_ICINVA) 380 381 #define CACR_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 382 CONFIG_SYS_INIT_RAM_SIZE - 12) 383 384 /*----------------------------------------------------------------------- 385 * Memory bank definitions 386 */ 387 /* 388 * CS0 - NOR Flash 16MB 389 * CS1 - Available 390 * CS2 - Available 391 * CS3 - Available 392 * CS4 - Available 393 * CS5 - Available 394 */ 395 396 /* Flash */ 397 #define CONFIG_SYS_CS0_BASE 0x00000000 398 #define CONFIG_SYS_CS0_MASK 0x000F0101 399 #define CONFIG_SYS_CS0_CTRL 0x00001D60 400 401 #endif /* _M54418TWR_H */ 402