1 /* 2 * Configuation settings for the Motorola MC5282EVB board. 3 * 4 * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 /* 10 * board/config.h - configuration options, board specific 11 */ 12 13 #ifndef _CONFIG_M5282EVB_H 14 #define _CONFIG_M5282EVB_H 15 16 /* 17 * High Level Configuration Options 18 * (easy to change) 19 */ 20 #define CONFIG_MCFTMR 21 22 #define CONFIG_MCFUART 23 #define CONFIG_SYS_UART_PORT (0) 24 25 #undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */ 26 27 /* Configuration for environment 28 * Environment is embedded in u-boot in the second sector of the flash 29 */ 30 #define CONFIG_ENV_ADDR 0xffe04000 31 #define CONFIG_ENV_SIZE 0x2000 32 33 #define LDS_BOARD_TEXT \ 34 . = DEFINED(env_offset) ? env_offset : .; \ 35 env/embedded.o(.text*); 36 37 /* 38 * BOOTP options 39 */ 40 #define CONFIG_BOOTP_BOOTFILESIZE 41 #define CONFIG_BOOTP_BOOTPATH 42 #define CONFIG_BOOTP_GATEWAY 43 #define CONFIG_BOOTP_HOSTNAME 44 45 /* 46 * Command line configuration. 47 */ 48 49 #define CONFIG_MCFFEC 50 #ifdef CONFIG_MCFFEC 51 # define CONFIG_MII 1 52 # define CONFIG_MII_INIT 1 53 # define CONFIG_SYS_DISCOVER_PHY 54 # define CONFIG_SYS_RX_ETH_BUFFER 8 55 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 56 57 # define CONFIG_SYS_FEC0_PINMUX 0 58 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 59 # define MCFFEC_TOUT_LOOP 50000 60 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 61 # ifndef CONFIG_SYS_DISCOVER_PHY 62 # define FECDUPLEX FULL 63 # define FECSPEED _100BASET 64 # else 65 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 66 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 67 # endif 68 # endif /* CONFIG_SYS_DISCOVER_PHY */ 69 #endif 70 71 #ifdef CONFIG_MCFFEC 72 # define CONFIG_IPADDR 192.162.1.2 73 # define CONFIG_NETMASK 255.255.255.0 74 # define CONFIG_SERVERIP 192.162.1.1 75 # define CONFIG_GATEWAYIP 192.162.1.1 76 #endif /* CONFIG_MCFFEC */ 77 78 #define CONFIG_HOSTNAME M5282EVB 79 #define CONFIG_EXTRA_ENV_SETTINGS \ 80 "netdev=eth0\0" \ 81 "loadaddr=10000\0" \ 82 "u-boot=u-boot.bin\0" \ 83 "load=tftp ${loadaddr) ${u-boot}\0" \ 84 "upd=run load; run prog\0" \ 85 "prog=prot off ffe00000 ffe3ffff;" \ 86 "era ffe00000 ffe3ffff;" \ 87 "cp.b ${loadaddr} ffe00000 ${filesize};"\ 88 "save\0" \ 89 "" 90 91 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 92 93 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 94 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 95 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 96 97 #define CONFIG_SYS_LOAD_ADDR 0x20000 98 99 #define CONFIG_SYS_MEMTEST_START 0x400 100 #define CONFIG_SYS_MEMTEST_END 0x380000 101 102 #define CONFIG_SYS_CLK 64000000 103 104 /* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */ 105 106 #define CONFIG_SYS_MFD 0x02 /* PLL Multiplication Factor Devider */ 107 #define CONFIG_SYS_RFD 0x00 /* PLL Reduce Frecuency Devider */ 108 109 /* 110 * Low Level Configuration Settings 111 * (address mappings, register initial values, etc.) 112 * You should know what you are doing if you make changes here. 113 */ 114 #define CONFIG_SYS_MBAR 0x40000000 115 116 /*----------------------------------------------------------------------- 117 * Definitions for initial stack pointer and data area (in DPRAM) 118 */ 119 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 120 #define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */ 121 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 122 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 123 124 /*----------------------------------------------------------------------- 125 * Start addresses for the final memory configuration 126 * (Set up by the startup code) 127 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 128 */ 129 #define CONFIG_SYS_SDRAM_BASE 0x00000000 130 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ 131 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE 132 #define CONFIG_SYS_INT_FLASH_BASE 0xf0000000 133 #define CONFIG_SYS_INT_FLASH_ENABLE 0x21 134 135 /* If M5282 port is fully implemented the monitor base will be behind 136 * the vector table. */ 137 #if (CONFIG_SYS_TEXT_BASE != CONFIG_SYS_INT_FLASH_BASE) 138 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 139 #else 140 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x418) /* 24 Byte for CFM-Config */ 141 #endif 142 143 #define CONFIG_SYS_MONITOR_LEN 0x20000 144 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 145 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 146 147 /* 148 * For booting Linux, the board info and command line data 149 * have to be in the first 8 MB of memory, since this is 150 * the maximum mapped by the Linux kernel during initialization ?? 151 */ 152 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) 153 154 /*----------------------------------------------------------------------- 155 * FLASH organization 156 */ 157 #define CONFIG_SYS_FLASH_CFI 158 #ifdef CONFIG_SYS_FLASH_CFI 159 160 # define CONFIG_FLASH_CFI_DRIVER 1 161 # define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */ 162 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 163 # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 164 # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ 165 # define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ 166 # define CONFIG_SYS_FLASH_CHECKSUM 167 # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } 168 #endif 169 170 /*----------------------------------------------------------------------- 171 * Cache Configuration 172 */ 173 #define CONFIG_SYS_CACHELINE_SIZE 16 174 175 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 176 CONFIG_SYS_INIT_RAM_SIZE - 8) 177 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 178 CONFIG_SYS_INIT_RAM_SIZE - 4) 179 #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV + CF_CACR_DCM) 180 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ 181 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 182 CF_ACR_EN | CF_ACR_SM_ALL) 183 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \ 184 CF_CACR_CEIB | CF_CACR_DBWE | \ 185 CF_CACR_EUSP) 186 187 /*----------------------------------------------------------------------- 188 * Memory bank definitions 189 */ 190 #define CONFIG_SYS_CS0_BASE 0xFFE00000 191 #define CONFIG_SYS_CS0_CTRL 0x00001980 192 #define CONFIG_SYS_CS0_MASK 0x001F0001 193 194 /*----------------------------------------------------------------------- 195 * Port configuration 196 */ 197 #define CONFIG_SYS_PACNT 0x0000000 /* Port A D[31:24] */ 198 #define CONFIG_SYS_PADDR 0x0000000 199 #define CONFIG_SYS_PADAT 0x0000000 200 201 #define CONFIG_SYS_PBCNT 0x0000000 /* Port B D[23:16] */ 202 #define CONFIG_SYS_PBDDR 0x0000000 203 #define CONFIG_SYS_PBDAT 0x0000000 204 205 #define CONFIG_SYS_PCCNT 0x0000000 /* Port C D[15:08] */ 206 #define CONFIG_SYS_PCDDR 0x0000000 207 #define CONFIG_SYS_PCDAT 0x0000000 208 209 #define CONFIG_SYS_PDCNT 0x0000000 /* Port D D[07:00] */ 210 #define CONFIG_SYS_PCDDR 0x0000000 211 #define CONFIG_SYS_PCDAT 0x0000000 212 213 #define CONFIG_SYS_PEHLPAR 0xC0 214 #define CONFIG_SYS_PUAPAR 0x0F /* UA0..UA3 = Uart 0 +1 */ 215 #define CONFIG_SYS_DDRUA 0x05 216 #define CONFIG_SYS_PJPAR 0xFF 217 218 #endif /* _CONFIG_M5282EVB_H */ 219