1 2menuconfig NAND 3 bool "NAND Device Support" 4if NAND 5 6config SYS_NAND_SELF_INIT 7 bool 8 help 9 This option, if enabled, provides more flexible and linux-like 10 NAND initialization process. 11 12config NAND_DENALI 13 bool 14 select SYS_NAND_SELF_INIT 15 imply CMD_NAND 16 17config NAND_DENALI_DT 18 bool "Support Denali NAND controller as a DT device" 19 select NAND_DENALI 20 depends on OF_CONTROL && DM 21 help 22 Enable the driver for NAND flash on platforms using a Denali NAND 23 controller as a DT device. 24 25config NAND_DENALI_SPARE_AREA_SKIP_BYTES 26 int "Number of bytes skipped in OOB area" 27 depends on NAND_DENALI 28 range 0 63 29 help 30 This option specifies the number of bytes to skip from the beginning 31 of OOB area before last ECC sector data starts. This is potentially 32 used to preserve the bad block marker in the OOB area. 33 34config NAND_OMAP_GPMC 35 bool "Support OMAP GPMC NAND controller" 36 depends on ARCH_OMAP2PLUS 37 help 38 Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms. 39 GPMC controller is used for parallel NAND flash devices, and can 40 do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8 41 and BCH16 ECC algorithms. 42 43config NAND_OMAP_GPMC_PREFETCH 44 bool "Enable GPMC Prefetch" 45 depends on NAND_OMAP_GPMC 46 default y 47 help 48 On OMAP platforms that use the GPMC controller 49 (CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that 50 uses the prefetch mode to speed up read operations. 51 52config NAND_OMAP_ELM 53 bool "Enable ELM driver for OMAPxx and AMxx platforms." 54 depends on NAND_OMAP_GPMC && !OMAP34XX 55 help 56 ELM controller is used for ECC error detection (not ECC calculation) 57 of BCH4, BCH8 and BCH16 ECC algorithms. 58 Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine, 59 thus such SoC platforms need to depend on software library for ECC error 60 detection. However ECC calculation on such plaforms would still be 61 done by GPMC controller. 62 63config NAND_VF610_NFC 64 bool "Support for Freescale NFC for VF610" 65 select SYS_NAND_SELF_INIT 66 imply CMD_NAND 67 help 68 Enables support for NAND Flash Controller on some Freescale 69 processors like the VF610, MCF54418 or Kinetis K70. 70 The driver supports a maximum 2k page size. The driver 71 currently does not support hardware ECC. 72 73choice 74 prompt "Hardware ECC strength" 75 depends on NAND_VF610_NFC 76 default SYS_NAND_VF610_NFC_45_ECC_BYTES 77 help 78 Select the ECC strength used in the hardware BCH ECC block. 79 80config SYS_NAND_VF610_NFC_45_ECC_BYTES 81 bool "24-error correction (45 ECC bytes)" 82 83config SYS_NAND_VF610_NFC_60_ECC_BYTES 84 bool "32-error correction (60 ECC bytes)" 85 86endchoice 87 88config NAND_PXA3XX 89 bool "Support for NAND on PXA3xx and Armada 370/XP/38x" 90 select SYS_NAND_SELF_INIT 91 imply CMD_NAND 92 help 93 This enables the driver for the NAND flash device found on 94 PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). 95 96config NAND_ROCKCHIP 97 bool "Support for NAND on Rockchip SoCs" 98 select SYS_NAND_SELF_INIT 99 default n 100 ---help--- 101 Enable support for Rockchip nand. 102 103config NAND_ROCKCHIP_V9 104 bool "Support for NAND V9 on Rockchip SoCs" 105 select SYS_NAND_SELF_INIT 106 default n 107 ---help--- 108 Enable support for Rockchip nand v9. 109 110if NAND_ROCKCHIP || NAND_ROCKCHIP_V9 111config NAND_ROCKCHIP_DT 112 bool "Support Rockchip NAND controller as a DT device" 113 default y 114 help 115 Enable the driver for Rockchip NAND flash on platforms 116 using device tree. 117endif 118 119config NAND_SUNXI 120 bool "Support for NAND on Allwinner SoCs" 121 default ARCH_SUNXI 122 depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I 123 select SYS_NAND_SELF_INIT 124 select SYS_NAND_U_BOOT_LOCATIONS 125 select SPL_NAND_SUPPORT 126 imply CMD_NAND 127 ---help--- 128 Enable support for NAND. This option enables the standard and 129 SPL drivers. 130 The SPL driver only supports reading from the NAND using DMA 131 transfers. 132 133if NAND_SUNXI 134 135config NAND_SUNXI_SPL_ECC_STRENGTH 136 int "Allwinner NAND SPL ECC Strength" 137 default 64 138 139config NAND_SUNXI_SPL_ECC_SIZE 140 int "Allwinner NAND SPL ECC Step Size" 141 default 1024 142 143config NAND_SUNXI_SPL_USABLE_PAGE_SIZE 144 int "Allwinner NAND SPL Usable Page Size" 145 default 1024 146 147endif 148 149config NAND_ARASAN 150 bool "Configure Arasan Nand" 151 select SYS_NAND_SELF_INIT 152 imply CMD_NAND 153 help 154 This enables Nand driver support for Arasan nand flash 155 controller. This uses the hardware ECC for read and 156 write operations. 157 158config NAND_MXC 159 bool "MXC NAND support" 160 depends on CPU_ARM926EJS || CPU_ARM1136 || MX5 161 imply CMD_NAND 162 help 163 This enables the NAND driver for the NAND flash controller on the 164 i.MX27 / i.MX31 / i.MX5 rocessors. 165 166config NAND_MXS 167 bool "MXS NAND support" 168 depends on MX23 || MX28 || MX6 || MX7 169 select SYS_NAND_SELF_INIT 170 imply CMD_NAND 171 select APBH_DMA 172 select APBH_DMA_BURST if ARCH_MX6 || ARCH_MX7 173 select APBH_DMA_BURST8 if ARCH_MX6 || ARCH_MX7 174 help 175 This enables NAND driver for the NAND flash controller on the 176 MXS processors. 177 178if NAND_MXS 179 180config NAND_MXS_DT 181 bool "Support MXS NAND controller as a DT device" 182 depends on OF_CONTROL && MTD 183 help 184 Enable the driver for MXS NAND flash on platforms using 185 device tree. 186 187config NAND_MXS_USE_MINIMUM_ECC 188 bool "Use minimum ECC strength supported by the controller" 189 default false 190 191endif 192 193config NAND_ZYNQ 194 bool "Support for Zynq Nand controller" 195 select SYS_NAND_SELF_INIT 196 imply CMD_NAND 197 help 198 This enables Nand driver support for Nand flash controller 199 found on Zynq SoC. 200 201config NAND_ZYNQ_USE_BOOTLOADER1_TIMINGS 202 bool "Enable use of 1st stage bootloader timing for NAND" 203 depends on NAND_ZYNQ 204 help 205 This flag prevent U-boot reconfigure NAND flash controller and reuse 206 the NAND timing from 1st stage bootloader. 207 208comment "Generic NAND options" 209 210config SYS_NAND_BLOCK_SIZE 211 hex "NAND chip eraseblock size" 212 depends on ARCH_SUNXI 213 help 214 Number of data bytes in one eraseblock for the NAND chip on the 215 board. This is the multiple of NAND_PAGE_SIZE and the number of 216 pages. 217 218config SYS_NAND_PAGE_SIZE 219 hex "NAND chip page size" 220 depends on ARCH_SUNXI 221 help 222 Number of data bytes in one page for the NAND chip on the 223 board, not including the OOB area. 224 225config SYS_NAND_OOBSIZE 226 hex "NAND chip OOB size" 227 depends on ARCH_SUNXI 228 help 229 Number of bytes in the Out-Of-Band area for the NAND chip on 230 the board. 231 232# Enhance depends when converting drivers to Kconfig which use this config 233# option (mxc_nand, ndfc, omap_gpmc). 234config SYS_NAND_BUSWIDTH_16BIT 235 bool "Use 16-bit NAND interface" 236 depends on NAND_VF610_NFC || NAND_OMAP_GPMC || NAND_MXC || ARCH_DAVINCI 237 help 238 Indicates that NAND device has 16-bit wide data-bus. In absence of this 239 config, bus-width of NAND device is assumed to be either 8-bit and later 240 determined by reading ONFI params. 241 Above config is useful when NAND device's bus-width information cannot 242 be determined from on-chip ONFI params, like in following scenarios: 243 - SPL boot does not support reading of ONFI parameters. This is done to 244 keep SPL code foot-print small. 245 - In current U-Boot flow using nand_init(), driver initialization 246 happens in board_nand_init() which is called before any device probe 247 (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are 248 not available while configuring controller. So a static CONFIG_NAND_xx 249 is needed to know the device's bus-width in advance. 250 251if SPL 252 253config SYS_NAND_U_BOOT_LOCATIONS 254 bool "Define U-boot binaries locations in NAND" 255 help 256 Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig. 257 This option should not be enabled when compiling U-boot for boards 258 defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h 259 file. 260 261config SYS_NAND_U_BOOT_OFFS 262 hex "Location in NAND to read U-Boot from" 263 default 0x800000 if NAND_SUNXI 264 depends on SYS_NAND_U_BOOT_LOCATIONS 265 help 266 Set the offset from the start of the nand where u-boot should be 267 loaded from. 268 269config SYS_NAND_U_BOOT_OFFS_REDUND 270 hex "Location in NAND to read U-Boot from" 271 default SYS_NAND_U_BOOT_OFFS 272 depends on SYS_NAND_U_BOOT_LOCATIONS 273 help 274 Set the offset from the start of the nand where the redundant u-boot 275 should be loaded from. 276 277config SPL_NAND_AM33XX_BCH 278 bool "Enables SPL-NAND driver which supports ELM based" 279 depends on NAND_OMAP_GPMC && !OMAP34XX 280 default y 281 help 282 Hardware ECC correction. This is useful for platforms which have ELM 283 hardware engine and use NAND boot mode. 284 Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine, 285 so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling 286 SPL-NAND driver with software ECC correction support. 287 288config SPL_NAND_DENALI 289 bool "Support Denali NAND controller for SPL" 290 help 291 This is a small implementation of the Denali NAND controller 292 for use on SPL. 293 294config SPL_NAND_SIMPLE 295 bool "Use simple SPL NAND driver" 296 depends on !SPL_NAND_AM33XX_BCH 297 help 298 Support for NAND boot using simple NAND drivers that 299 expose the cmd_ctrl() interface. 300endif 301 302endif # if NAND 303