1menu "Command line interface" 2 3config CMDLINE 4 bool "Support U-Boot commands" 5 default y 6 help 7 Enable U-Boot's command-line functions. This provides a means 8 to enter commands into U-Boot for a wide variety of purposes. It 9 also allows scripts (containing commands) to be executed. 10 Various commands and command categorys can be indivdually enabled. 11 Depending on the number of commands enabled, this can add 12 substantially to the size of U-Boot. 13 14config HUSH_PARSER 15 bool "Use hush shell" 16 depends on CMDLINE 17 help 18 This option enables the "hush" shell (from Busybox) as command line 19 interpreter, thus enabling powerful command line syntax like 20 if...then...else...fi conditionals or `&&' and '||' 21 constructs ("shell scripts"). 22 23 If disabled, you get the old, much simpler behaviour with a somewhat 24 smaller memory footprint. 25 26config SYS_PROMPT 27 string "Shell prompt" 28 default "=> " 29 help 30 This string is displayed in the command line to the left of the 31 cursor. 32 33menu "Autoboot options" 34 35config AUTOBOOT 36 bool "Autoboot" 37 default y 38 help 39 This enables the autoboot. See doc/README.autoboot for detail. 40 41config AUTOBOOT_KEYED 42 bool "Stop autobooting via specific input key / string" 43 default n 44 help 45 This option enables stopping (aborting) of the automatic 46 boot feature only by issuing a specific input key or 47 string. If not enabled, any input key will abort the 48 U-Boot automatic booting process and bring the device 49 to the U-Boot prompt for user input. 50 51config AUTOBOOT_PROMPT 52 string "Autoboot stop prompt" 53 depends on AUTOBOOT_KEYED 54 default "Autoboot in %d seconds\\n" 55 help 56 This string is displayed before the boot delay selected by 57 CONFIG_BOOTDELAY starts. If it is not defined there is no 58 output indicating that autoboot is in progress. 59 60 Note that this define is used as the (only) argument to a 61 printf() call, so it may contain '%' format specifications, 62 provided that it also includes, sepearated by commas exactly 63 like in a printf statement, the required arguments. It is 64 the responsibility of the user to select only such arguments 65 that are valid in the given context. 66 67config AUTOBOOT_ENCRYPTION 68 bool "Enable encryption in autoboot stopping" 69 depends on AUTOBOOT_KEYED 70 default n 71 72config AUTOBOOT_DELAY_STR 73 string "Delay autobooting via specific input key / string" 74 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 75 help 76 This option delays the automatic boot feature by issuing 77 a specific input key or string. If CONFIG_AUTOBOOT_DELAY_STR 78 or the environment variable "bootdelaykey" is specified 79 and this string is received from console input before 80 autoboot starts booting, U-Boot gives a command prompt. The 81 U-Boot prompt will time out if CONFIG_BOOT_RETRY_TIME is 82 used, otherwise it never times out. 83 84config AUTOBOOT_STOP_STR 85 string "Stop autobooting via specific input key / string" 86 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 87 help 88 This option enables stopping (aborting) of the automatic 89 boot feature only by issuing a specific input key or 90 string. If CONFIG_AUTOBOOT_STOP_STR or the environment 91 variable "bootstopkey" is specified and this string is 92 received from console input before autoboot starts booting, 93 U-Boot gives a command prompt. The U-Boot prompt never 94 times out, even if CONFIG_BOOT_RETRY_TIME is used. 95 96config AUTOBOOT_KEYED_CTRLC 97 bool "Enable Ctrl-C autoboot interruption" 98 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 99 default n 100 help 101 This option allows for the boot sequence to be interrupted 102 by ctrl-c, in addition to the "bootdelaykey" and "bootstopkey". 103 Setting this variable provides an escape sequence from the 104 limited "password" strings. 105 106config AUTOBOOT_STOP_STR_SHA256 107 string "Stop autobooting via SHA256 encrypted password" 108 depends on AUTOBOOT_KEYED && AUTOBOOT_ENCRYPTION 109 help 110 This option adds the feature to only stop the autobooting, 111 and therefore boot into the U-Boot prompt, when the input 112 string / password matches a values that is encypted via 113 a SHA256 hash and saved in the environment. 114 115endmenu 116 117source "cmd/fastboot/Kconfig" 118 119comment "Commands" 120 121menu "Info commands" 122 123config CMD_BDI 124 bool "bdinfo" 125 default y 126 help 127 Print board info 128 129config CMD_CONFIG 130 bool "config" 131 select BUILD_BIN2C 132 default SANDBOX 133 help 134 Print ".config" contents. 135 136 If this option is enabled, the ".config" file contents are embedded 137 in the U-Boot image and can be printed on the console by the "config" 138 command. This provides information of which options are enabled on 139 the running U-Boot. 140 141config CMD_CONSOLE 142 bool "coninfo" 143 default y 144 help 145 Print console devices and information. 146 147config CMD_CPU 148 bool "cpu" 149 help 150 Print information about available CPUs. This normally shows the 151 number of CPUs, type (e.g. manufacturer, architecture, product or 152 internal name) and clock frequency. Other information may be 153 available depending on the CPU driver. 154 155config CMD_LICENSE 156 bool "license" 157 select BUILD_BIN2C 158 help 159 Print GPL license text 160 161endmenu 162 163menu "Boot commands" 164 165config CMD_BOOTD 166 bool "bootd" 167 default y 168 help 169 Run the command stored in the environment "bootcmd", i.e. 170 "bootd" does the same thing as "run bootcmd". 171 172config CMD_BOOTM 173 bool "bootm" 174 default y 175 help 176 Boot an application image from the memory. 177 178config CMD_BOOTZ 179 bool "bootz" 180 help 181 Boot the Linux zImage 182 183config CMD_BOOTI 184 bool "booti" 185 depends on ARM64 186 default y 187 help 188 Boot an AArch64 Linux Kernel image from memory. 189 190config CMD_BOOTEFI 191 bool "bootefi" 192 depends on EFI_LOADER 193 default y 194 help 195 Boot an EFI image from memory. 196 197config CMD_BOOTEFI_HELLO_COMPILE 198 bool "Compile a standard EFI hello world binary for testing" 199 depends on CMD_BOOTEFI && (ARM || X86) 200 default y 201 help 202 This compiles a standard EFI hello world application with U-Boot so 203 that it can be used with the test/py testing framework. This is useful 204 for testing that EFI is working at a basic level, and for bringing 205 up EFI support on a new architecture. 206 207 No additional space will be required in the resulting U-Boot binary 208 when this option is enabled. 209 210config CMD_BOOTEFI_HELLO 211 bool "Allow booting a standard EFI hello world for testing" 212 depends on CMD_BOOTEFI_HELLO_COMPILE 213 help 214 This adds a standard EFI hello world application to U-Boot so that 215 it can be used with the 'bootefi hello' command. This is useful 216 for testing that EFI is working at a basic level, and for bringing 217 up EFI support on a new architecture. 218 219config CMD_BOOTMENU 220 bool "bootmenu" 221 select MENU 222 help 223 Add an ANSI terminal boot menu command. 224 225config CMD_ELF 226 bool "bootelf, bootvx" 227 default y 228 help 229 Boot an ELF/vxWorks image from the memory. 230 231config CMD_FDT 232 bool "Flattened Device Tree utility commands" 233 default y 234 depends on OF_LIBFDT 235 help 236 Do FDT related setup before booting into the Operating System. 237 238config CMD_GO 239 bool "go" 240 default y 241 help 242 Start an application at a given address. 243 244config CMD_RUN 245 bool "run" 246 default y 247 help 248 Run the command in the given environment variable. 249 250config CMD_IMI 251 bool "iminfo" 252 default y 253 help 254 Print header information for application image. 255 256config CMD_IMLS 257 bool "imls" 258 default y 259 help 260 List all images found in flash 261 262config CMD_XIMG 263 bool "imxtract" 264 default y 265 help 266 Extract a part of a multi-image. 267 268config CMD_POWEROFF 269 bool "poweroff" 270 help 271 Poweroff/Shutdown the system 272 273endmenu 274 275menu "Environment commands" 276 277config CMD_ASKENV 278 bool "ask for env variable" 279 help 280 Ask for environment variable 281 282config CMD_EXPORTENV 283 bool "env export" 284 default y 285 help 286 Export environments. 287 288config CMD_IMPORTENV 289 bool "env import" 290 default y 291 help 292 Import environments. 293 294config CMD_EDITENV 295 bool "editenv" 296 default y 297 help 298 Edit environment variable. 299 300config CMD_GREPENV 301 bool "search env" 302 help 303 Allow for searching environment variables 304 305config CMD_SAVEENV 306 bool "saveenv" 307 default y 308 help 309 Save all environment variables into the compiled-in persistent 310 storage. 311 312config CMD_ENV_EXISTS 313 bool "env exists" 314 default y 315 help 316 Check if a variable is defined in the environment for use in 317 shell scripting. 318 319config CMD_ENV_CALLBACK 320 bool "env callbacks - print callbacks and their associated variables" 321 help 322 Some environment variable have callbacks defined by 323 U_BOOT_ENV_CALLBACK. These are called when the variable changes. 324 For example changing "baudrate" adjust the serial baud rate. This 325 command lists the currently defined callbacks. 326 327config CMD_ENV_FLAGS 328 bool "env flags -print variables that have non-default flags" 329 help 330 Some environment variables have special flags that control their 331 behaviour. For example, serial# can only be written once and cannot 332 be deleted. This command shows the variables that have special 333 flags. 334 335endmenu 336 337menu "Memory commands" 338 339config CMD_MEMORY 340 bool "md, mm, nm, mw, cp, cmp, base, loop" 341 default y 342 help 343 Memory commands. 344 md - memory display 345 mm - memory modify (auto-incrementing address) 346 nm - memory modify (constant address) 347 mw - memory write (fill) 348 cp - memory copy 349 cmp - memory compare 350 base - print or set address offset 351 loop - initialize loop on address range 352 353config CMD_CRC32 354 bool "crc32" 355 select HASH 356 default y 357 help 358 Compute CRC32. 359 360config CRC32_VERIFY 361 bool "crc32 -v" 362 depends on CMD_CRC32 363 help 364 Add -v option to verify data against a crc32 checksum. 365 366config CMD_EEPROM 367 bool "eeprom - EEPROM subsystem" 368 help 369 (deprecated, needs conversion to driver model) 370 Provides commands to read and write EEPROM (Electrically Erasable 371 Programmable Read Only Memory) chips that are connected over an 372 I2C bus. 373 374config CMD_EEPROM_LAYOUT 375 bool "Enable layout-aware eeprom commands" 376 depends on CMD_EEPROM 377 help 378 (deprecated, needs conversion to driver model) 379 When enabled, additional eeprom sub-commands become available. 380 381 eeprom print - prints the contents of the eeprom in a human-readable 382 way (eeprom layout fields, and data formatted to be fit for human 383 consumption). 384 385 eeprom update - allows user to update eeprom fields by specifying 386 the field name, and providing the new data in a human readable format 387 (same format as displayed by the eeprom print command). 388 389 Both commands can either auto detect the layout, or be told which 390 layout to use. 391 392 Feature API: 393 __weak int parse_layout_version(char *str) 394 - override to provide your own layout name parsing 395 __weak void __eeprom_layout_assign(struct eeprom_layout *layout, 396 int layout_version); 397 - override to setup the layout metadata based on the version 398 __weak int eeprom_layout_detect(unsigned char *data) 399 - override to provide your own algorithm for detecting layout 400 version 401 eeprom_field.c 402 - contains various printing and updating functions for common 403 types of eeprom fields. Can be used for defining 404 custom layouts. 405 406config EEPROM_LAYOUT_HELP_STRING 407 string "Tells user what layout names are supported" 408 depends on CMD_EEPROM_LAYOUT 409 default "<not defined>" 410 help 411 Help printed with the LAYOUT VERSIONS part of the 'eeprom' 412 command's help. 413 414config CMD_MD5SUM 415 bool "md5sum" 416 default n 417 select MD5 418 help 419 Compute MD5 checksum. 420 421config MD5SUM_VERIFY 422 bool "md5sum -v" 423 default n 424 depends on CMD_MD5SUM 425 help 426 Add -v option to verify data against an MD5 checksum. 427 428config CMD_SHA1SUM 429 bool "sha1sum" 430 select SHA1 431 help 432 Compute SHA1 checksum. 433 434config SHA1SUM_VERIFY 435 bool "sha1sum -v" 436 depends on CMD_SHA1SUM 437 help 438 Add -v option to verify data against a SHA1 checksum. 439 440config LOOPW 441 bool "loopw" 442 help 443 Infinite write loop on address range 444 445config CMD_MEMTEST 446 bool "memtest" 447 help 448 Simple RAM read/write test. 449 450config CMD_MX_CYCLIC 451 bool "mdc, mwc" 452 help 453 mdc - memory display cyclic 454 mwc - memory write cyclic 455 456config CMD_MEMINFO 457 bool "meminfo" 458 help 459 Display memory information. 460 461endmenu 462 463menu "Compression commands" 464 465config CMD_LZMADEC 466 bool "lzmadec" 467 select LZMA 468 help 469 Support decompressing an LZMA (Lempel-Ziv-Markov chain algorithm) 470 image from memory. 471 472config CMD_UNZIP 473 bool "unzip" 474 help 475 Uncompress a zip-compressed memory region. 476 477config CMD_ZIP 478 bool "zip" 479 help 480 Compress a memory region with zlib deflate method. 481 482endmenu 483 484menu "Device access commands" 485 486config CMD_ARMFLASH 487 #depends on FLASH_CFI_DRIVER 488 bool "armflash" 489 help 490 ARM Ltd reference designs flash partition access 491 492config CMD_CLK 493 bool "clk - Show clock frequencies" 494 help 495 (deprecated) 496 Shows clock frequences by calling a sock_clk_dump() hook function. 497 This is depreated in favour of using the CLK uclass and accessing 498 clock values from associated drivers. However currently no command 499 exists for this. 500 501config CMD_DEMO 502 bool "demo - Demonstration commands for driver model" 503 depends on DM 504 help 505 Provides a 'demo' command which can be used to play around with 506 driver model. To use this properly you will need to enable one or 507 both of the demo devices (DM_DEMO_SHAPE and DM_DEMO_SIMPLE). 508 Otherwise you will always get an empty list of devices. The demo 509 devices are defined in the sandbox device tree, so the easiest 510 option is to use sandbox and pass the -d point to sandbox's 511 u-boot.dtb file. 512 513config CMD_DFU 514 bool "dfu" 515 select USB_FUNCTION_DFU 516 help 517 Enables the command "dfu" which is used to have U-Boot create a DFU 518 class device via USB. 519 520config CMD_DM 521 bool "dm - Access to driver model information" 522 depends on DM 523 default y 524 help 525 Provides access to driver model data structures and information, 526 such as a list of devices, list of uclasses and the state of each 527 device (e.g. activated). This is not required for operation, but 528 can be useful to see the state of driver model for debugging or 529 interest. 530 531config CMD_FDC 532 bool "fdcboot - Boot from floppy device" 533 help 534 The 'fdtboot' command allows booting an image from a floppy disk. 535 536config CMD_FLASH 537 bool "flinfo, erase, protect" 538 default y 539 help 540 NOR flash support. 541 flinfo - print FLASH memory information 542 erase - FLASH memory 543 protect - enable or disable FLASH write protection 544 545config CMD_FPGA 546 bool "fpga" 547 default y 548 help 549 FPGA support. 550 551config CMD_FPGA_LOADBP 552 bool "fpga loadbp - load partial bitstream (Xilinx only)" 553 depends on CMD_FPGA 554 help 555 Supports loading an FPGA device from a bitstream buffer containing 556 a partial bitstream. 557 558config CMD_FPGA_LOADFS 559 bool "fpga loadfs - load bitstream from FAT filesystem (Xilinx only)" 560 depends on CMD_FPGA 561 help 562 Supports loading an FPGA device from a FAT filesystem. 563 564config CMD_FPGA_LOADMK 565 bool "fpga loadmk - load bitstream from image" 566 depends on CMD_FPGA 567 help 568 Supports loading an FPGA device from a image generated by mkimage. 569 570config CMD_FPGA_LOADP 571 bool "fpga loadp - load partial bitstream" 572 depends on CMD_FPGA 573 help 574 Supports loading an FPGA device from a bitstream buffer containing 575 a partial bitstream. 576 577config CMD_FPGAD 578 bool "fpgad - dump FPGA registers" 579 help 580 (legacy, needs conversion to driver model) 581 Provides a way to dump FPGA registers by calling the board-specific 582 fpga_get_reg() function. This functions similarly to the 'md' 583 command. 584 585config CMD_FUSE 586 bool "fuse - support for the fuse subssystem" 587 help 588 (deprecated - needs conversion to driver model) 589 This allows reading, sensing, programming or overriding fuses 590 which control the behaviour of the device. The command uses the 591 fuse_...() API. 592 593config CMD_GPIO 594 bool "gpio" 595 help 596 GPIO support. 597 598config CMD_GPT 599 bool "GPT (GUID Partition Table) command" 600 select PARTITION_UUIDS 601 select EFI_PARTITION 602 help 603 Enable the 'gpt' command to ready and write GPT style partition 604 tables. 605 606config CMD_GPT_RENAME 607 bool "GPT partition renaming commands" 608 depends on CMD_GPT 609 help 610 Enables the 'gpt' command to interchange names on two GPT 611 partitions via the 'gpt swap' command or to rename single 612 partitions via the 'rename' command. 613 614config CMD_IDE 615 bool "ide - Support for IDE drivers" 616 select IDE 617 help 618 Provides an 'ide' command which allows accessing the IDE drive, 619 reseting the IDE interface, printing the partition table and 620 geting device info. It also enables the 'diskboot' command which 621 permits booting from an IDE drive. 622 623config CMD_IO 624 bool "io - Support for performing I/O accesses" 625 help 626 Provides an 'iod' command to display I/O space and an 'iow' command 627 to write values to the I/O space. This can be useful for manually 628 checking the state of devices during boot when debugging device 629 drivers, etc. 630 631config CMD_IOTRACE 632 bool "iotrace - Support for tracing I/O activity" 633 help 634 Provides an 'iotrace' command which supports recording I/O reads and 635 writes in a trace buffer in memory . It also maintains a checksum 636 of the trace records (even if space is exhausted) so that the 637 sequence of I/O accesses can be verified. 638 639 When debugging drivers it is useful to see what I/O accesses were 640 done and in what order. 641 642 Even if the individual accesses are of little interest it can be 643 useful to verify that the access pattern is consistent each time 644 an operation is performed. In this case a checksum can be used to 645 characterise the operation of a driver. The checksum can be compared 646 across different runs of the operation to verify that the driver is 647 working properly. 648 649 In particular, when performing major refactoring of the driver, where 650 the access pattern should not change, the checksum provides assurance 651 that the refactoring work has not broken the driver. 652 653 This works by sneaking into the io.h heder for an architecture and 654 redirecting I/O accesses through iotrace's tracing mechanism. 655 656 For now no commands are provided to examine the trace buffer. The 657 format is fairly simple, so 'md' is a reasonable substitute. 658 659 Note: The checksum feature is only useful for I/O regions where the 660 contents do not change outside of software control. Where this is not 661 suitable you can fall back to manually comparing the addresses. It 662 might be useful to enhance tracing to only checksum the accesses and 663 not the data read/written. 664 665config CMD_I2C 666 bool "i2c" 667 help 668 I2C support. 669 670config CMD_LOADB 671 bool "loadb" 672 default y 673 help 674 Load a binary file over serial line. 675 676config CMD_LOADS 677 bool "loads" 678 default y 679 help 680 Load an S-Record file over serial line 681 682config CMD_MMC 683 bool "mmc" 684 help 685 MMC memory mapped support. 686 687config CMD_NAND 688 bool "nand" 689 default y if NAND_SUNXI 690 help 691 NAND support. 692 693if CMD_NAND 694config CMD_NAND_TRIMFFS 695 bool "nand write.trimffs" 696 default y if ARCH_SUNXI 697 help 698 Allows one to skip empty pages when flashing something on a NAND. 699 700config CMD_NAND_LOCK_UNLOCK 701 bool "nand lock/unlock" 702 help 703 NAND locking support. 704 705config CMD_NAND_TORTURE 706 bool "nand torture" 707 help 708 NAND torture support. 709 710endif # CMD_NAND 711 712config CMD_MMC_SPI 713 bool "mmc_spi - Set up MMC SPI device" 714 help 715 Provides a way to set up an MMC (Multimedia Card) SPI (Serial 716 Peripheral Interface) device. The device provides a means of 717 accessing an MMC device via SPI using a single data line, limited 718 to 20MHz. It is useful since it reduces the amount of protocol code 719 required. 720 721config CMD_ONENAND 722 bool "onenand - access to onenand device" 723 help 724 OneNAND is a brand of NAND ('Not AND' gate) flash which provides 725 various useful features. This command allows reading, writing, 726 and erasing blocks. It allso provides a way to show and change 727 bad blocks, and test the device. 728 729config CMD_PART 730 bool "part" 731 select PARTITION_UUIDS 732 help 733 Read and display information about the partition table on 734 various media. 735 736config CMD_REMOTEPROC 737 bool "remoteproc" 738 depends on REMOTEPROC 739 help 740 Support for Remote Processor control 741 742config CMD_SATA 743 bool "sata - Access SATA subsystem" 744 select SATA 745 help 746 SATA (Serial Advanced Technology Attachment) is a serial bus 747 standard for connecting to hard drives and other storage devices. 748 This command provides information about attached devices and allows 749 reading, writing and other operations. 750 751 SATA replaces PATA (originally just ATA), which stands for Parallel AT 752 Attachment, where AT refers to an IBM AT (Advanced Technology) 753 computer released in 1984. 754 755config CMD_SF 756 bool "sf" 757 help 758 SPI Flash support 759 760config CMD_SPI 761 bool "sspi" 762 help 763 SPI utility command. 764 765config CMD_USB 766 bool "usb" 767 help 768 USB support. 769 770config CMD_USB_MASS_STORAGE 771 bool "UMS usb mass storage" 772 help 773 USB mass storage support 774 775endmenu 776 777 778menu "Shell scripting commands" 779 780config CMD_ECHO 781 bool "echo" 782 default y 783 help 784 Echo args to console 785 786config CMD_ITEST 787 bool "itest" 788 default y 789 help 790 Return true/false on integer compare. 791 792config CMD_SOURCE 793 bool "source" 794 default y 795 help 796 Run script from memory 797 798config CMD_SETEXPR 799 bool "setexpr" 800 default y 801 help 802 Evaluate boolean and math expressions and store the result in an env 803 variable. 804 Also supports loading the value at a memory location into a variable. 805 If CONFIG_REGEX is enabled, setexpr also supports a gsub function. 806 807endmenu 808 809menu "Network commands" 810 811config CMD_NET 812 bool "bootp, tftpboot" 813 select NET 814 default y 815 help 816 Network commands. 817 bootp - boot image via network using BOOTP/TFTP protocol 818 tftpboot - boot image via network using TFTP protocol 819 820config CMD_TFTPPUT 821 bool "tftp put" 822 help 823 TFTP put command, for uploading files to a server 824 825config CMD_TFTPSRV 826 bool "tftpsrv" 827 help 828 Act as a TFTP server and boot the first received file 829 830config CMD_RARP 831 bool "rarpboot" 832 help 833 Boot image via network using RARP/TFTP protocol 834 835config CMD_DHCP 836 bool "dhcp" 837 help 838 Boot image via network using DHCP/TFTP protocol 839 840config CMD_PXE 841 bool "pxe" 842 select MENU 843 help 844 Boot image via network using PXE protocol 845 846config CMD_NFS 847 bool "nfs" 848 default y 849 help 850 Boot image via network using NFS protocol. 851 852config CMD_MII 853 bool "mii" 854 help 855 Enable MII utility commands. 856 857config CMD_PING 858 bool "ping" 859 help 860 Send ICMP ECHO_REQUEST to network host 861 862config CMD_CDP 863 bool "cdp" 864 help 865 Perform CDP network configuration 866 867config CMD_SNTP 868 bool "sntp" 869 help 870 Synchronize RTC via network 871 872config CMD_DNS 873 bool "dns" 874 help 875 Lookup the IP of a hostname 876 877config CMD_LINK_LOCAL 878 bool "linklocal" 879 help 880 Acquire a network IP address using the link-local protocol 881 882config CMD_ETHSW 883 bool "ethsw" 884 help 885 Allow control of L2 Ethernet switch commands. These are supported 886 by the vsc9953 Ethernet driver at present. Sub-commands allow 887 operations such as enabling / disabling a port and 888 viewing/maintaining the filtering database (FDB) 889 890endmenu 891 892menu "Misc commands" 893 894config CMD_BMP 895 bool "Enable 'bmp' command" 896 depends on LCD || DM_VIDEO || VIDEO 897 help 898 This provides a way to obtain information about a BMP-format iamge 899 and to display it. BMP (which presumably stands for BitMaP) is a 900 file format defined by Microsoft which supports images of various 901 depths, formats and compression methods. Headers on the file 902 determine the formats used. This command can be used by first loading 903 the image into RAM, then using this command to look at it or display 904 it. 905 906config CMD_BSP 907 bool "Enable board-specific commands" 908 help 909 (deprecated: instead, please define a Kconfig option for each command) 910 911 Some boards have board-specific commands which are only enabled 912 during developemnt and need to be turned off for production. This 913 option provides a way to control this. The commands that are enabled 914 vary depending on the board. 915 916config CMD_BKOPS_ENABLE 917 bool "mmc bkops enable" 918 depends on CMD_MMC 919 default n 920 help 921 Enable command for setting manual background operations handshake 922 on a eMMC device. The feature is optionally available on eMMC devices 923 conforming to standard >= 4.41. 924 925config CMD_BLOCK_CACHE 926 bool "blkcache - control and stats for block cache" 927 depends on BLOCK_CACHE 928 default y if BLOCK_CACHE 929 help 930 Enable the blkcache command, which can be used to control the 931 operation of the cache functions. 932 This is most useful when fine-tuning the operation of the cache 933 during development, but also allows the cache to be disabled when 934 it might hurt performance (e.g. when using the ums command). 935 936config CMD_CACHE 937 bool "icache or dcache" 938 help 939 Enable the "icache" and "dcache" commands 940 941config CMD_DISPLAY 942 bool "Enable the 'display' command, for character displays" 943 help 944 (this needs porting to driver model) 945 This enables the 'display' command which allows a string to be 946 displayed on a simple board-specific display. Implement 947 display_putc() to use it. 948 949config CMD_LED 950 bool "led" 951 default y if LED 952 help 953 Enable the 'led' command which allows for control of LEDs supported 954 by the board. The LEDs can be listed with 'led list' and controlled 955 with led on/off/togle/blink. Any LED drivers can be controlled with 956 this command, e.g. led_gpio. 957 958config CMD_DATE 959 bool "date" 960 default y if DM_RTC 961 help 962 Enable the 'date' command for getting/setting the time/date in RTC 963 devices. 964 965config CMD_TIME 966 bool "time" 967 help 968 Run commands and summarize execution time. 969 970config CMD_GETTIME 971 bool "gettime - read elapsed time" 972 help 973 Enable the 'gettime' command which reads the elapsed time since 974 U-Boot started running. This shows the time in seconds and 975 milliseconds. See also the 'bootstage' command which provides more 976 flexibility for boot timing. 977 978# TODO: rename to CMD_SLEEP 979config CMD_MISC 980 bool "sleep" 981 default y 982 help 983 Delay execution for some time 984 985config CMD_TIMER 986 bool "timer" 987 help 988 Access the system timer. 989 990config CMD_SOUND 991 bool "sound" 992 depends on SOUND 993 help 994 This provides basic access to the U-Boot's sound support. The main 995 feature is to play a beep. 996 997 sound init - set up sound system 998 sound play - play a sound 999 1000config CMD_QFW 1001 bool "qfw" 1002 select QFW 1003 help 1004 This provides access to the QEMU firmware interface. The main 1005 feature is to allow easy loading of files passed to qemu-system 1006 via -kernel / -initrd 1007 1008source "cmd/mvebu/Kconfig" 1009 1010endmenu 1011 1012config CMD_BOOTSTAGE 1013 bool "Enable the 'bootstage' command" 1014 depends on BOOTSTAGE 1015 help 1016 Add a 'bootstage' command which supports printing a report 1017 and un/stashing of bootstage data. 1018 1019menu "Power commands" 1020config CMD_PMIC 1021 bool "Enable Driver Model PMIC command" 1022 depends on DM_PMIC 1023 help 1024 This is the pmic command, based on a driver model pmic's API. 1025 Command features are unchanged: 1026 - list - list pmic devices 1027 - pmic dev <id> - show or [set] operating pmic device (NEW) 1028 - pmic dump - dump registers 1029 - pmic read address - read byte of register at address 1030 - pmic write address - write byte to register at address 1031 The only one change for this command is 'dev' subcommand. 1032 1033config CMD_REGULATOR 1034 bool "Enable Driver Model REGULATOR command" 1035 depends on DM_REGULATOR 1036 help 1037 This command is based on driver model regulator's API. 1038 User interface features: 1039 - list - list regulator devices 1040 - regulator dev <id> - show or [set] operating regulator device 1041 - regulator info - print constraints info 1042 - regulator status - print operating status 1043 - regulator value <val] <-f> - print/[set] voltage value [uV] 1044 - regulator current <val> - print/[set] current value [uA] 1045 - regulator mode <id> - print/[set] operating mode id 1046 - regulator enable - enable the regulator output 1047 - regulator disable - disable the regulator output 1048 1049 The '-f' (force) option can be used for set the value which exceeds 1050 the limits, which are found in device-tree and are kept in regulator's 1051 uclass platdata structure. 1052 1053endmenu 1054 1055menu "Security commands" 1056config CMD_AES 1057 bool "Enable the 'aes' command" 1058 select AES 1059 help 1060 This provides a means to encrypt and decrypt data using the AES 1061 (Advanced Encryption Standard). This algorithm uses a symetric key 1062 and is widely used as a streaming cipher. Different key lengths are 1063 supported by the algorithm but this command only supports 128 bits 1064 at present. 1065 1066config CMD_BLOB 1067 bool "Enable the 'blob' command" 1068 help 1069 This is used with the Freescale secure boot mechanism. 1070 1071 Freescale's SEC block has built-in Blob Protocol which provides 1072 a method for protecting user-defined data across system power 1073 cycles. SEC block protects data in a data structure called a Blob, 1074 which provides both confidentiality and integrity protection. 1075 1076 Encapsulating data as a blob 1077 Each time that the Blob Protocol is used to protect data, a 1078 different randomly generated key is used to encrypt the data. 1079 This random key is itself encrypted using a key which is derived 1080 from SoC's non-volatile secret key and a 16 bit Key identifier. 1081 The resulting encrypted key along with encrypted data is called a 1082 blob. The non-volatile secure key is available for use only during 1083 secure boot. 1084 1085 During decapsulation, the reverse process is performed to get back 1086 the original data. 1087 1088 Sub-commands: 1089 blob enc - encapsulating data as a cryptgraphic blob 1090 blob dec - decapsulating cryptgraphic blob to get the data 1091 1092 Syntax: 1093 1094 blob enc src dst len km 1095 1096 Encapsulate and create blob of data $len bytes long 1097 at address $src and store the result at address $dst. 1098 $km is the 16 byte key modifier is also required for 1099 generation/use as key for cryptographic operation. Key 1100 modifier should be 16 byte long. 1101 1102 blob dec src dst len km 1103 1104 Decapsulate the blob of data at address $src and 1105 store result of $len byte at addr $dst. 1106 $km is the 16 byte key modifier is also required for 1107 generation/use as key for cryptographic operation. Key 1108 modifier should be 16 byte long. 1109 1110config CMD_HASH 1111 bool "Support 'hash' command" 1112 select HASH 1113 help 1114 This provides a way to hash data in memory using various supported 1115 algorithms (such as SHA1, MD5, CRC32). The computed digest can be 1116 saved to memory or to an environment variable. It is also possible 1117 to verify a hash against data in memory. 1118 1119config HASH_VERIFY 1120 bool "hash -v" 1121 depends on CMD_HASH 1122 help 1123 Add -v option to verify data against a hash. 1124 1125config CMD_TPM 1126 bool "Enable the 'tpm' command" 1127 depends on TPM 1128 help 1129 This provides a means to talk to a TPM from the command line. A wide 1130 range of commands if provided - see 'tpm help' for details. The 1131 command requires a suitable TPM on your board and the correct driver 1132 must be enabled. 1133 1134config CMD_TPM_TEST 1135 bool "Enable the 'tpm test' command" 1136 depends on CMD_TPM 1137 help 1138 This provides a a series of tests to confirm that the TPM is working 1139 correctly. The tests cover initialisation, non-volatile RAM, extend, 1140 global lock and checking that timing is within expectations. The 1141 tests pass correctly on Infineon TPMs but may need to be adjusted 1142 for other devices. 1143 1144endmenu 1145 1146menu "Firmware commands" 1147config CMD_CROS_EC 1148 bool "Enable crosec command" 1149 depends on CROS_EC 1150 default y 1151 help 1152 Enable command-line access to the Chrome OS EC (Embedded 1153 Controller). This provides the 'crosec' command which has 1154 a number of sub-commands for performing EC tasks such as 1155 updating its flash, accessing a small saved context area 1156 and talking to the I2C bus behind the EC (if there is one). 1157endmenu 1158 1159menu "Filesystem commands" 1160config CMD_CBFS 1161 bool "Enable the 'cbfs' command" 1162 depends on FS_CBFS 1163 help 1164 Define this to enable support for reading from a Coreboot 1165 filesystem. This is a ROM-based filesystem used for accessing files 1166 on systems that use coreboot as the first boot-loader and then load 1167 U-Boot to actually boot the Operating System. Available commands are 1168 cbfsinit, cbfsinfo, cbfsls and cbfsload. 1169 1170config CMD_CRAMFS 1171 bool "Enable the 'cramfs' command" 1172 depends on FS_CRAMFS 1173 help 1174 This provides commands for dealing with CRAMFS (Compressed ROM 1175 filesystem). CRAMFS is useful when space is tight since files are 1176 compressed. Two commands are provided: 1177 1178 cramfsls - lists files in a cramfs image 1179 cramfsload - loads a file from a cramfs image 1180 1181config CMD_EXT2 1182 bool "ext2 command support" 1183 help 1184 Enables EXT2 FS command 1185 1186config CMD_EXT4 1187 bool "ext4 command support" 1188 help 1189 Enables EXT4 FS command 1190 1191config CMD_EXT4_WRITE 1192 depends on CMD_EXT4 1193 bool "ext4 write command support" 1194 help 1195 Enables EXT4 FS write command 1196 1197config CMD_FAT 1198 bool "FAT command support" 1199 select FS_FAT 1200 help 1201 Support for the FAT fs 1202 1203config CMD_FS_GENERIC 1204 bool "filesystem commands" 1205 help 1206 Enables filesystem commands (e.g. load, ls) that work for multiple 1207 fs types. 1208 1209config CMD_FS_UUID 1210 bool "fsuuid command" 1211 help 1212 Enables fsuuid command for filesystem UUID. 1213 1214config CMD_JFFS2 1215 bool "jffs2 command" 1216 select FS_JFFS2 1217 help 1218 Enables commands to support the JFFS2 (Journalling Flash File System 1219 version 2) filesystem. This enables fsload, ls and fsinfo which 1220 provide the ability to load files, list directories and obtain 1221 filesystem information. 1222 1223config CMD_MTDPARTS 1224 bool "MTD partition support" 1225 help 1226 MTD partition support 1227 1228config MTDIDS_DEFAULT 1229 string "Default MTD IDs" 1230 depends on CMD_MTDPARTS 1231 help 1232 Defines a default MTD ID 1233 1234config MTDPARTS_DEFAULT 1235 string "Default MTD partition scheme" 1236 depends on CMD_MTDPARTS 1237 help 1238 Defines a default MTD partitioning scheme in the Linux MTD command 1239 line partitions format 1240 1241config CMD_MTDPARTS_SPREAD 1242 bool "Padd partition size to take account of bad blocks" 1243 depends on CMD_MTDPARTS 1244 help 1245 This enables the 'spread' sub-command of the mtdparts command. 1246 This command will modify the existing mtdparts variable by increasing 1247 the size of the partitions such that 1) each partition's net size is 1248 at least as large as the size specified in the mtdparts variable and 1249 2) each partition starts on a good block. 1250 1251endmenu 1252 1253menu "Debug commands" 1254 1255config CMD_BEDBUG 1256 bool "bedbug" 1257 help 1258 The bedbug (emBEDded deBUGger) command provides debugging features 1259 for some PowerPC processors. For details please see the 1260 docuemntation in doc/README.beddbug 1261 1262config CMD_DIAG 1263 bool "diag - Board diagnostics" 1264 help 1265 This command provides access to board diagnostic tests. These are 1266 called Power-on Self Tests (POST). The command allows listing of 1267 available tests and running either all the tests, or specific tests 1268 identified by name. 1269 1270config CMD_IRQ 1271 bool "irq - Show information about interrupts" 1272 depends on !ARM && !MIPS && !SH 1273 help 1274 This enables two commands: 1275 1276 interrupts - enable or disable interrupts 1277 irqinfo - print device-specific interrupt information 1278 1279config CMD_KGDB 1280 bool "kgdb - Allow debugging of U-Boot with gdb" 1281 help 1282 This enables a 'kgdb' command which allows gdb to connect to U-Boot 1283 over a serial link for debugging purposes. This allows 1284 single-stepping, inspecting variables, etc. This is supported only 1285 on PowerPC at present. 1286 1287endmenu 1288 1289config CMD_UBI 1290 tristate "Enable UBI - Unsorted block images commands" 1291 select CRC32 1292 select MTD_UBI 1293 select CMD_MTDPARTS 1294 default y if NAND_SUNXI 1295 help 1296 UBI is a software layer above MTD layer which admits use of LVM-like 1297 logical volumes on top of MTD devices, hides some complexities of 1298 flash chips like wear and bad blocks and provides some other useful 1299 capabilities. Please, consult the MTD web site for more details 1300 (www.linux-mtd.infradead.org). Activate this option if you want 1301 to use U-Boot UBI commands. 1302 1303config CMD_UBIFS 1304 tristate "Enable UBIFS - Unsorted block images filesystem commands" 1305 depends on CMD_UBI 1306 select CRC32 1307 select LZO 1308 default y if CMD_UBI 1309 help 1310 UBIFS is a file system for flash devices which works on top of UBI. 1311 1312endmenu 1313