1menu "Command line interface" 2 3config CMDLINE 4 bool "Support U-Boot commands" 5 default y 6 help 7 Enable U-Boot's command-line functions. This provides a means 8 to enter commands into U-Boot for a wide variety of purposes. It 9 also allows scripts (containing commands) to be executed. 10 Various commands and command categorys can be indivdually enabled. 11 Depending on the number of commands enabled, this can add 12 substantially to the size of U-Boot. 13 14config HUSH_PARSER 15 bool "Use hush shell" 16 depends on CMDLINE 17 help 18 This option enables the "hush" shell (from Busybox) as command line 19 interpreter, thus enabling powerful command line syntax like 20 if...then...else...fi conditionals or `&&' and '||' 21 constructs ("shell scripts"). 22 23 If disabled, you get the old, much simpler behaviour with a somewhat 24 smaller memory footprint. 25 26config SYS_PROMPT 27 string "Shell prompt" 28 default "=> " 29 help 30 This string is displayed in the command line to the left of the 31 cursor. 32 33menu "Autoboot options" 34 35config AUTOBOOT 36 bool "Autoboot" 37 default y 38 help 39 This enables the autoboot. See doc/README.autoboot for detail. 40 41config AUTOBOOT_KEYED 42 bool "Stop autobooting via specific input key / string" 43 default n 44 help 45 This option enables stopping (aborting) of the automatic 46 boot feature only by issuing a specific input key or 47 string. If not enabled, any input key will abort the 48 U-Boot automatic booting process and bring the device 49 to the U-Boot prompt for user input. 50 51config AUTOBOOT_PROMPT 52 string "Autoboot stop prompt" 53 depends on AUTOBOOT_KEYED 54 default "Autoboot in %d seconds\\n" 55 help 56 This string is displayed before the boot delay selected by 57 CONFIG_BOOTDELAY starts. If it is not defined there is no 58 output indicating that autoboot is in progress. 59 60 Note that this define is used as the (only) argument to a 61 printf() call, so it may contain '%' format specifications, 62 provided that it also includes, sepearated by commas exactly 63 like in a printf statement, the required arguments. It is 64 the responsibility of the user to select only such arguments 65 that are valid in the given context. 66 67config AUTOBOOT_ENCRYPTION 68 bool "Enable encryption in autoboot stopping" 69 depends on AUTOBOOT_KEYED 70 default n 71 72config AUTOBOOT_DELAY_STR 73 string "Delay autobooting via specific input key / string" 74 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 75 help 76 This option delays the automatic boot feature by issuing 77 a specific input key or string. If CONFIG_AUTOBOOT_DELAY_STR 78 or the environment variable "bootdelaykey" is specified 79 and this string is received from console input before 80 autoboot starts booting, U-Boot gives a command prompt. The 81 U-Boot prompt will time out if CONFIG_BOOT_RETRY_TIME is 82 used, otherwise it never times out. 83 84config AUTOBOOT_STOP_STR 85 string "Stop autobooting via specific input key / string" 86 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 87 help 88 This option enables stopping (aborting) of the automatic 89 boot feature only by issuing a specific input key or 90 string. If CONFIG_AUTOBOOT_STOP_STR or the environment 91 variable "bootstopkey" is specified and this string is 92 received from console input before autoboot starts booting, 93 U-Boot gives a command prompt. The U-Boot prompt never 94 times out, even if CONFIG_BOOT_RETRY_TIME is used. 95 96config AUTOBOOT_KEYED_CTRLC 97 bool "Enable Ctrl-C autoboot interruption" 98 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 99 default n 100 help 101 This option allows for the boot sequence to be interrupted 102 by ctrl-c, in addition to the "bootdelaykey" and "bootstopkey". 103 Setting this variable provides an escape sequence from the 104 limited "password" strings. 105 106config AUTOBOOT_STOP_STR_SHA256 107 string "Stop autobooting via SHA256 encrypted password" 108 depends on AUTOBOOT_KEYED && AUTOBOOT_ENCRYPTION 109 help 110 This option adds the feature to only stop the autobooting, 111 and therefore boot into the U-Boot prompt, when the input 112 string / password matches a values that is encypted via 113 a SHA256 hash and saved in the environment. 114 115endmenu 116 117source "cmd/fastboot/Kconfig" 118 119comment "Commands" 120 121menu "Info commands" 122 123config CMD_BDI 124 bool "bdinfo" 125 default y 126 help 127 Print board info 128 129config CMD_CONFIG 130 bool "config" 131 select BUILD_BIN2C 132 default SANDBOX 133 help 134 Print ".config" contents. 135 136 If this option is enabled, the ".config" file contents are embedded 137 in the U-Boot image and can be printed on the console by the "config" 138 command. This provides information of which options are enabled on 139 the running U-Boot. 140 141config CMD_CONSOLE 142 bool "coninfo" 143 default y 144 help 145 Print console devices and information. 146 147config CMD_CPU 148 bool "cpu" 149 help 150 Print information about available CPUs. This normally shows the 151 number of CPUs, type (e.g. manufacturer, architecture, product or 152 internal name) and clock frequency. Other information may be 153 available depending on the CPU driver. 154 155config CMD_LICENSE 156 bool "license" 157 select BUILD_BIN2C 158 help 159 Print GPL license text 160 161config CMD_REGINFO 162 bool "reginfo" 163 depends on PPC 164 help 165 Register dump 166 167endmenu 168 169menu "Boot commands" 170 171config CMD_BOOTD 172 bool "bootd" 173 default y 174 help 175 Run the command stored in the environment "bootcmd", i.e. 176 "bootd" does the same thing as "run bootcmd". 177 178config CMD_BOOTM 179 bool "bootm" 180 default y 181 help 182 Boot an application image from the memory. 183 184config CMD_BOOTZ 185 bool "bootz" 186 help 187 Boot the Linux zImage 188 189config CMD_BOOTI 190 bool "booti" 191 depends on ARM64 192 default y 193 help 194 Boot an AArch64 Linux Kernel image from memory. 195 196config CMD_BOOTEFI 197 bool "bootefi" 198 depends on EFI_LOADER 199 default y 200 help 201 Boot an EFI image from memory. 202 203config CMD_BOOTEFI_HELLO_COMPILE 204 bool "Compile a standard EFI hello world binary for testing" 205 depends on CMD_BOOTEFI && (ARM || X86) 206 default y 207 help 208 This compiles a standard EFI hello world application with U-Boot so 209 that it can be used with the test/py testing framework. This is useful 210 for testing that EFI is working at a basic level, and for bringing 211 up EFI support on a new architecture. 212 213 No additional space will be required in the resulting U-Boot binary 214 when this option is enabled. 215 216config CMD_BOOTEFI_HELLO 217 bool "Allow booting a standard EFI hello world for testing" 218 depends on CMD_BOOTEFI_HELLO_COMPILE 219 help 220 This adds a standard EFI hello world application to U-Boot so that 221 it can be used with the 'bootefi hello' command. This is useful 222 for testing that EFI is working at a basic level, and for bringing 223 up EFI support on a new architecture. 224 225config CMD_BOOTMENU 226 bool "bootmenu" 227 select MENU 228 help 229 Add an ANSI terminal boot menu command. 230 231config CMD_ELF 232 bool "bootelf, bootvx" 233 default y 234 help 235 Boot an ELF/vxWorks image from the memory. 236 237config CMD_FDT 238 bool "Flattened Device Tree utility commands" 239 default y 240 depends on OF_LIBFDT 241 help 242 Do FDT related setup before booting into the Operating System. 243 244config CMD_GO 245 bool "go" 246 default y 247 help 248 Start an application at a given address. 249 250config CMD_RUN 251 bool "run" 252 default y 253 help 254 Run the command in the given environment variable. 255 256config CMD_IMI 257 bool "iminfo" 258 default y 259 help 260 Print header information for application image. 261 262config CMD_IMLS 263 bool "imls" 264 default y 265 help 266 List all images found in flash 267 268config CMD_XIMG 269 bool "imxtract" 270 default y 271 help 272 Extract a part of a multi-image. 273 274config CMD_POWEROFF 275 bool "poweroff" 276 help 277 Poweroff/Shutdown the system 278 279config CMD_SPL 280 bool "spl export - Export boot information for Falcon boot" 281 depends on SPL 282 help 283 Falcon mode allows booting directly from SPL into an Operating 284 System such as Linux, thus skipping U-Boot proper. See 285 doc/README.falcon for full information about how to use this 286 command. 287 288config CMD_SPL_NAND_OFS 289 hex "Offset of OS command line args for Falcon-mode NAND boot" 290 depends on CMD_SPL 291 default 0 292 help 293 This provides the offset of the command line arguments for Linux 294 when booting from NAND in Falcon mode. See doc/README.falcon 295 for full information about how to use this option (and also see 296 board/gateworks/gw_ventana/README for an example). 297 298config CMD_SPL_WRITE_SIZE 299 hex "Size of argument area" 300 depends on CMD_SPL 301 default 0x2000 302 help 303 This provides the size of the command-line argument area in NAND 304 flash used by Falcon-mode boot. See the documentation until CMD_SPL 305 for detail. 306 307config CMD_THOR_DOWNLOAD 308 bool "thor - TIZEN 'thor' download" 309 help 310 Implements the 'thor' download protocol. This is a way of 311 downloading a software update over USB from an attached host. 312 There is no documentation about this within the U-Boot source code 313 but you should be able to find something on the interwebs. 314 315config CMD_ZBOOT 316 bool "zboot - x86 boot command" 317 help 318 With x86 machines it is common to boot a bzImage file which 319 contains both a kernel and a setup.bin file. The latter includes 320 configuration information from the dark ages which x86 boards still 321 need to pick things out of. 322 323 Consider using FIT in preference to this since it supports directly 324 booting both 32- and 64-bit kernels, as well as secure boot. 325 Documentation is available in doc/uImage.FIT/x86-fit-boot.txt 326 327endmenu 328 329menu "Environment commands" 330 331config CMD_ASKENV 332 bool "ask for env variable" 333 help 334 Ask for environment variable 335 336config CMD_EXPORTENV 337 bool "env export" 338 default y 339 help 340 Export environments. 341 342config CMD_IMPORTENV 343 bool "env import" 344 default y 345 help 346 Import environments. 347 348config CMD_EDITENV 349 bool "editenv" 350 default y 351 help 352 Edit environment variable. 353 354config CMD_GREPENV 355 bool "search env" 356 help 357 Allow for searching environment variables 358 359config CMD_SAVEENV 360 bool "saveenv" 361 default y 362 help 363 Save all environment variables into the compiled-in persistent 364 storage. 365 366config CMD_ENV_EXISTS 367 bool "env exists" 368 default y 369 help 370 Check if a variable is defined in the environment for use in 371 shell scripting. 372 373config CMD_ENV_CALLBACK 374 bool "env callbacks - print callbacks and their associated variables" 375 help 376 Some environment variable have callbacks defined by 377 U_BOOT_ENV_CALLBACK. These are called when the variable changes. 378 For example changing "baudrate" adjust the serial baud rate. This 379 command lists the currently defined callbacks. 380 381config CMD_ENV_FLAGS 382 bool "env flags -print variables that have non-default flags" 383 help 384 Some environment variables have special flags that control their 385 behaviour. For example, serial# can only be written once and cannot 386 be deleted. This command shows the variables that have special 387 flags. 388 389endmenu 390 391menu "Memory commands" 392 393config CMD_CRC32 394 bool "crc32" 395 select HASH 396 default y 397 help 398 Compute CRC32. 399 400config CRC32_VERIFY 401 bool "crc32 -v" 402 depends on CMD_CRC32 403 help 404 Add -v option to verify data against a crc32 checksum. 405 406config CMD_EEPROM 407 bool "eeprom - EEPROM subsystem" 408 help 409 (deprecated, needs conversion to driver model) 410 Provides commands to read and write EEPROM (Electrically Erasable 411 Programmable Read Only Memory) chips that are connected over an 412 I2C bus. 413 414config CMD_EEPROM_LAYOUT 415 bool "Enable layout-aware eeprom commands" 416 depends on CMD_EEPROM 417 help 418 (deprecated, needs conversion to driver model) 419 When enabled, additional eeprom sub-commands become available. 420 421 eeprom print - prints the contents of the eeprom in a human-readable 422 way (eeprom layout fields, and data formatted to be fit for human 423 consumption). 424 425 eeprom update - allows user to update eeprom fields by specifying 426 the field name, and providing the new data in a human readable format 427 (same format as displayed by the eeprom print command). 428 429 Both commands can either auto detect the layout, or be told which 430 layout to use. 431 432 Feature API: 433 __weak int parse_layout_version(char *str) 434 - override to provide your own layout name parsing 435 __weak void __eeprom_layout_assign(struct eeprom_layout *layout, 436 int layout_version); 437 - override to setup the layout metadata based on the version 438 __weak int eeprom_layout_detect(unsigned char *data) 439 - override to provide your own algorithm for detecting layout 440 version 441 eeprom_field.c 442 - contains various printing and updating functions for common 443 types of eeprom fields. Can be used for defining 444 custom layouts. 445 446config EEPROM_LAYOUT_HELP_STRING 447 string "Tells user what layout names are supported" 448 depends on CMD_EEPROM_LAYOUT 449 default "<not defined>" 450 help 451 Help printed with the LAYOUT VERSIONS part of the 'eeprom' 452 command's help. 453 454config LOOPW 455 bool "loopw" 456 help 457 Infinite write loop on address range 458 459config CMD_MD5SUM 460 bool "md5sum" 461 default n 462 select MD5 463 help 464 Compute MD5 checksum. 465 466config MD5SUM_VERIFY 467 bool "md5sum -v" 468 default n 469 depends on CMD_MD5SUM 470 help 471 Add -v option to verify data against an MD5 checksum. 472 473config CMD_MEMINFO 474 bool "meminfo" 475 help 476 Display memory information. 477 478config CMD_MEMORY 479 bool "md, mm, nm, mw, cp, cmp, base, loop" 480 default y 481 help 482 Memory commands. 483 md - memory display 484 mm - memory modify (auto-incrementing address) 485 nm - memory modify (constant address) 486 mw - memory write (fill) 487 cp - memory copy 488 cmp - memory compare 489 base - print or set address offset 490 loop - initialize loop on address range 491 492config CMD_MEMTEST 493 bool "memtest" 494 help 495 Simple RAM read/write test. 496 497config CMD_MX_CYCLIC 498 bool "mdc, mwc" 499 help 500 mdc - memory display cyclic 501 mwc - memory write cyclic 502 503config CMD_SHA1SUM 504 bool "sha1sum" 505 select SHA1 506 help 507 Compute SHA1 checksum. 508 509config SHA1SUM_VERIFY 510 bool "sha1sum -v" 511 depends on CMD_SHA1SUM 512 help 513 Add -v option to verify data against a SHA1 checksum. 514 515config CMD_STRINGS 516 bool "strings - display strings in memory" 517 help 518 This works similarly to the Unix 'strings' command except that it 519 works with a memory range. String of printable characters found 520 within the range are displayed. The minimum number of characters 521 for a sequence to be considered a string can be provided. 522 523endmenu 524 525menu "Compression commands" 526 527config CMD_LZMADEC 528 bool "lzmadec" 529 select LZMA 530 help 531 Support decompressing an LZMA (Lempel-Ziv-Markov chain algorithm) 532 image from memory. 533 534config CMD_UNZIP 535 bool "unzip" 536 help 537 Uncompress a zip-compressed memory region. 538 539config CMD_ZIP 540 bool "zip" 541 help 542 Compress a memory region with zlib deflate method. 543 544endmenu 545 546menu "Device access commands" 547 548config CMD_ARMFLASH 549 #depends on FLASH_CFI_DRIVER 550 bool "armflash" 551 help 552 ARM Ltd reference designs flash partition access 553 554config CMD_CLK 555 bool "clk - Show clock frequencies" 556 help 557 (deprecated) 558 Shows clock frequences by calling a sock_clk_dump() hook function. 559 This is depreated in favour of using the CLK uclass and accessing 560 clock values from associated drivers. However currently no command 561 exists for this. 562 563config CMD_DEMO 564 bool "demo - Demonstration commands for driver model" 565 depends on DM 566 help 567 Provides a 'demo' command which can be used to play around with 568 driver model. To use this properly you will need to enable one or 569 both of the demo devices (DM_DEMO_SHAPE and DM_DEMO_SIMPLE). 570 Otherwise you will always get an empty list of devices. The demo 571 devices are defined in the sandbox device tree, so the easiest 572 option is to use sandbox and pass the -d point to sandbox's 573 u-boot.dtb file. 574 575config CMD_DFU 576 bool "dfu" 577 select USB_FUNCTION_DFU 578 help 579 Enables the command "dfu" which is used to have U-Boot create a DFU 580 class device via USB. This command requires that the "dfu_alt_info" 581 environment variable be set and define the alt settings to expose to 582 the host. 583 584config CMD_DM 585 bool "dm - Access to driver model information" 586 depends on DM 587 default y 588 help 589 Provides access to driver model data structures and information, 590 such as a list of devices, list of uclasses and the state of each 591 device (e.g. activated). This is not required for operation, but 592 can be useful to see the state of driver model for debugging or 593 interest. 594 595config CMD_FDC 596 bool "fdcboot - Boot from floppy device" 597 help 598 The 'fdtboot' command allows booting an image from a floppy disk. 599 600config CMD_FLASH 601 bool "flinfo, erase, protect" 602 default y 603 help 604 NOR flash support. 605 flinfo - print FLASH memory information 606 erase - FLASH memory 607 protect - enable or disable FLASH write protection 608 609config CMD_FPGA 610 bool "fpga" 611 default y 612 help 613 FPGA support. 614 615config CMD_FPGA_LOADBP 616 bool "fpga loadbp - load partial bitstream (Xilinx only)" 617 depends on CMD_FPGA 618 help 619 Supports loading an FPGA device from a bitstream buffer containing 620 a partial bitstream. 621 622config CMD_FPGA_LOADFS 623 bool "fpga loadfs - load bitstream from FAT filesystem (Xilinx only)" 624 depends on CMD_FPGA 625 help 626 Supports loading an FPGA device from a FAT filesystem. 627 628config CMD_FPGA_LOADMK 629 bool "fpga loadmk - load bitstream from image" 630 depends on CMD_FPGA 631 help 632 Supports loading an FPGA device from a image generated by mkimage. 633 634config CMD_FPGA_LOADP 635 bool "fpga loadp - load partial bitstream" 636 depends on CMD_FPGA 637 help 638 Supports loading an FPGA device from a bitstream buffer containing 639 a partial bitstream. 640 641config CMD_FPGAD 642 bool "fpgad - dump FPGA registers" 643 help 644 (legacy, needs conversion to driver model) 645 Provides a way to dump FPGA registers by calling the board-specific 646 fpga_get_reg() function. This functions similarly to the 'md' 647 command. 648 649config CMD_FUSE 650 bool "fuse - support for the fuse subssystem" 651 help 652 (deprecated - needs conversion to driver model) 653 This allows reading, sensing, programming or overriding fuses 654 which control the behaviour of the device. The command uses the 655 fuse_...() API. 656 657config CMD_GPIO 658 bool "gpio" 659 help 660 GPIO support. 661 662config CMD_GPT 663 bool "GPT (GUID Partition Table) command" 664 select PARTITION_UUIDS 665 select EFI_PARTITION 666 help 667 Enable the 'gpt' command to ready and write GPT style partition 668 tables. 669 670config CMD_GPT_RENAME 671 bool "GPT partition renaming commands" 672 depends on CMD_GPT 673 help 674 Enables the 'gpt' command to interchange names on two GPT 675 partitions via the 'gpt swap' command or to rename single 676 partitions via the 'rename' command. 677 678config CMD_IDE 679 bool "ide - Support for IDE drivers" 680 select IDE 681 help 682 Provides an 'ide' command which allows accessing the IDE drive, 683 reseting the IDE interface, printing the partition table and 684 geting device info. It also enables the 'diskboot' command which 685 permits booting from an IDE drive. 686 687config CMD_IO 688 bool "io - Support for performing I/O accesses" 689 help 690 Provides an 'iod' command to display I/O space and an 'iow' command 691 to write values to the I/O space. This can be useful for manually 692 checking the state of devices during boot when debugging device 693 drivers, etc. 694 695config CMD_IOTRACE 696 bool "iotrace - Support for tracing I/O activity" 697 help 698 Provides an 'iotrace' command which supports recording I/O reads and 699 writes in a trace buffer in memory . It also maintains a checksum 700 of the trace records (even if space is exhausted) so that the 701 sequence of I/O accesses can be verified. 702 703 When debugging drivers it is useful to see what I/O accesses were 704 done and in what order. 705 706 Even if the individual accesses are of little interest it can be 707 useful to verify that the access pattern is consistent each time 708 an operation is performed. In this case a checksum can be used to 709 characterise the operation of a driver. The checksum can be compared 710 across different runs of the operation to verify that the driver is 711 working properly. 712 713 In particular, when performing major refactoring of the driver, where 714 the access pattern should not change, the checksum provides assurance 715 that the refactoring work has not broken the driver. 716 717 This works by sneaking into the io.h heder for an architecture and 718 redirecting I/O accesses through iotrace's tracing mechanism. 719 720 For now no commands are provided to examine the trace buffer. The 721 format is fairly simple, so 'md' is a reasonable substitute. 722 723 Note: The checksum feature is only useful for I/O regions where the 724 contents do not change outside of software control. Where this is not 725 suitable you can fall back to manually comparing the addresses. It 726 might be useful to enhance tracing to only checksum the accesses and 727 not the data read/written. 728 729config CMD_I2C 730 bool "i2c" 731 help 732 I2C support. 733 734config CMD_LOADB 735 bool "loadb" 736 default y 737 help 738 Load a binary file over serial line. 739 740config CMD_LOADS 741 bool "loads" 742 default y 743 help 744 Load an S-Record file over serial line 745 746config CMD_LOAD_ANDROID 747 bool "load_android" 748 default n 749 depends on ANDROID_BOOT_IMAGE 750 help 751 Load an Android Boot image from storage. The Android Boot images 752 define the size and kernel address on the header, which are used by 753 this command. 754 755config CMD_BOOT_ANDROID 756 bool "boot_android" 757 default n 758 depends on ANDROID_BOOTLOADER 759 help 760 Performs the Android Bootloader boot flow, loading the appropriate 761 Android image (normal kernel, recovery kernel or "bootloader" mode) 762 and booting it. The boot mode is determined by the contents of the 763 Android Bootloader Message. 764 765config CMD_MMC 766 bool "mmc" 767 help 768 MMC memory mapped support. 769 770config CMD_NAND 771 bool "nand" 772 default y if NAND_SUNXI 773 help 774 NAND support. 775 776if CMD_NAND 777config CMD_NAND_TRIMFFS 778 bool "nand write.trimffs" 779 default y if ARCH_SUNXI 780 help 781 Allows one to skip empty pages when flashing something on a NAND. 782 783config CMD_NAND_LOCK_UNLOCK 784 bool "nand lock/unlock" 785 help 786 NAND locking support. 787 788config CMD_NAND_TORTURE 789 bool "nand torture" 790 help 791 NAND torture support. 792 793endif # CMD_NAND 794 795config CMD_NVME 796 bool "nvme" 797 depends on NVME 798 default y if NVME 799 help 800 NVM Express device support 801 802config CMD_MMC_SPI 803 bool "mmc_spi - Set up MMC SPI device" 804 help 805 Provides a way to set up an MMC (Multimedia Card) SPI (Serial 806 Peripheral Interface) device. The device provides a means of 807 accessing an MMC device via SPI using a single data line, limited 808 to 20MHz. It is useful since it reduces the amount of protocol code 809 required. 810 811config CMD_ONENAND 812 bool "onenand - access to onenand device" 813 help 814 OneNAND is a brand of NAND ('Not AND' gate) flash which provides 815 various useful features. This command allows reading, writing, 816 and erasing blocks. It allso provides a way to show and change 817 bad blocks, and test the device. 818 819config CMD_PART 820 bool "part" 821 select PARTITION_UUIDS 822 help 823 Read and display information about the partition table on 824 various media. 825 826config CMD_PCI 827 bool "pci - Access PCI devices" 828 help 829 Provide access to PCI (Peripheral Interconnect Bus), a type of bus 830 used on some devices to allow the CPU to communicate with its 831 peripherals. Sub-commands allow bus enumeration, displaying and 832 changing configuration space and a few other features. 833 834config CMD_PCMCIA 835 bool "pinit - Set up PCMCIA device" 836 help 837 Provides a means to initialise a PCMCIA (Personal Computer Memory 838 Card International Association) device. This is an old standard from 839 about 1990. These devices are typically removable memory or network 840 cards using a standard 68-pin connector. 841 842config CMD_READ 843 bool "read - Read binary data from a partition" 844 help 845 Provides low-level access to the data in a partition. 846 847config CMD_REMOTEPROC 848 bool "remoteproc" 849 depends on REMOTEPROC 850 help 851 Support for Remote Processor control 852 853config CMD_ROCKUSB 854 bool "rockusb - Command to upgrade Rockchip device" 855 depends on USB_GADGET 856 help 857 Rockusb command provides a way to upgrade firmware for 858 Rockchip SoC based devices, its design make use of USB 859 Bulk-Only Transport based on UMS framework. 860 861config CMD_RKNAND 862 bool "rknand" 863 depends on RKNAND 864 default y if RKNAND 865 help 866 Rockchip NAND FLASH device support 867 868config CMD_SATA 869 bool "sata - Access SATA subsystem" 870 select SATA 871 help 872 SATA (Serial Advanced Technology Attachment) is a serial bus 873 standard for connecting to hard drives and other storage devices. 874 This command provides information about attached devices and allows 875 reading, writing and other operations. 876 877 SATA replaces PATA (originally just ATA), which stands for Parallel AT 878 Attachment, where AT refers to an IBM AT (Advanced Technology) 879 computer released in 1984. 880 881config CMD_SAVES 882 bool "saves - Save a file over serial in S-Record format" 883 help 884 Provides a way to save a binary file using the Motorola S-Record 885 format over the serial line. 886 887config CMD_SDRAM 888 bool "sdram - Print SDRAM configuration information" 889 help 890 Provides information about attached SDRAM. This assumed that the 891 SDRAM has an EEPROM with information that can be read using the 892 I2C bus. This is only available on some boards. 893 894config CMD_SF 895 bool "sf" 896 help 897 SPI Flash support 898 899config CMD_SF_TEST 900 bool "sf test - Allow testing of SPI flash" 901 help 902 Provides a way to test that SPI flash is working correctly. The 903 test is destructive, in that an area of SPI flash must be provided 904 for the test to use. Performance information is also provided, 905 measuring the performance of reading, writing and erasing in 906 Mbps (Million Bits Per Second). This value should approximately 907 equal the SPI bus speed for a single-bit-wide SPI bus, assuming 908 everything is working properly. 909 910config CMD_SPI 911 bool "sspi" 912 help 913 SPI utility command. 914 915config CMD_TSI148 916 bool "tsi148 - Command to access tsi148 device" 917 help 918 This provides various sub-commands to initialise and configure the 919 Turndra tsi148 device. See the command help for full details. 920 921config CMD_UNIVERSE 922 bool "universe - Command to set up the Turndra Universe controller" 923 help 924 This allows setting up the VMEbus provided by this controller. 925 See the command help for full details. 926 927config CMD_USB 928 bool "usb" 929 help 930 USB support. 931 932config CMD_USB_SDP 933 bool "sdp" 934 select USB_FUNCTION_SDP 935 help 936 Enables the command "sdp" which is used to have U-Boot emulating the 937 Serial Download Protocol (SDP) via USB. 938 939config CMD_USB_MASS_STORAGE 940 bool "UMS usb mass storage" 941 help 942 USB mass storage support 943 944endmenu 945 946 947menu "Shell scripting commands" 948 949config CMD_ECHO 950 bool "echo" 951 default y 952 help 953 Echo args to console 954 955config CMD_ITEST 956 bool "itest" 957 default y 958 help 959 Return true/false on integer compare. 960 961config CMD_SOURCE 962 bool "source" 963 default y 964 help 965 Run script from memory 966 967config CMD_SETEXPR 968 bool "setexpr" 969 default y 970 help 971 Evaluate boolean and math expressions and store the result in an env 972 variable. 973 Also supports loading the value at a memory location into a variable. 974 If CONFIG_REGEX is enabled, setexpr also supports a gsub function. 975 976endmenu 977 978menu "Network commands" 979 980config CMD_NET 981 bool "bootp, tftpboot" 982 select NET 983 default y 984 help 985 Network commands. 986 bootp - boot image via network using BOOTP/TFTP protocol 987 tftpboot - boot image via network using TFTP protocol 988 989config CMD_TFTPPUT 990 bool "tftp put" 991 help 992 TFTP put command, for uploading files to a server 993 994config CMD_TFTPSRV 995 bool "tftpsrv" 996 help 997 Act as a TFTP server and boot the first received file 998 999config CMD_RARP 1000 bool "rarpboot" 1001 help 1002 Boot image via network using RARP/TFTP protocol 1003 1004config CMD_DHCP 1005 bool "dhcp" 1006 help 1007 Boot image via network using DHCP/TFTP protocol 1008 1009config CMD_PXE 1010 bool "pxe" 1011 select MENU 1012 help 1013 Boot image via network using PXE protocol 1014 1015config CMD_NFS 1016 bool "nfs" 1017 default y 1018 help 1019 Boot image via network using NFS protocol. 1020 1021config CMD_MII 1022 bool "mii" 1023 help 1024 Enable MII utility commands. 1025 1026config CMD_PING 1027 bool "ping" 1028 help 1029 Send ICMP ECHO_REQUEST to network host 1030 1031config CMD_CDP 1032 bool "cdp" 1033 help 1034 Perform CDP network configuration 1035 1036config CMD_SNTP 1037 bool "sntp" 1038 help 1039 Synchronize RTC via network 1040 1041config CMD_DNS 1042 bool "dns" 1043 help 1044 Lookup the IP of a hostname 1045 1046config CMD_LINK_LOCAL 1047 bool "linklocal" 1048 help 1049 Acquire a network IP address using the link-local protocol 1050 1051config CMD_ETHSW 1052 bool "ethsw" 1053 help 1054 Allow control of L2 Ethernet switch commands. These are supported 1055 by the vsc9953 Ethernet driver at present. Sub-commands allow 1056 operations such as enabling / disabling a port and 1057 viewing/maintaining the filtering database (FDB) 1058 1059endmenu 1060 1061menu "Misc commands" 1062 1063config CMD_BMP 1064 bool "Enable 'bmp' command" 1065 depends on LCD || DM_VIDEO || VIDEO 1066 help 1067 This provides a way to obtain information about a BMP-format iamge 1068 and to display it. BMP (which presumably stands for BitMaP) is a 1069 file format defined by Microsoft which supports images of various 1070 depths, formats and compression methods. Headers on the file 1071 determine the formats used. This command can be used by first loading 1072 the image into RAM, then using this command to look at it or display 1073 it. 1074 1075config CMD_BSP 1076 bool "Enable board-specific commands" 1077 help 1078 (deprecated: instead, please define a Kconfig option for each command) 1079 1080 Some boards have board-specific commands which are only enabled 1081 during developemnt and need to be turned off for production. This 1082 option provides a way to control this. The commands that are enabled 1083 vary depending on the board. 1084 1085config CMD_BKOPS_ENABLE 1086 bool "mmc bkops enable" 1087 depends on CMD_MMC 1088 default n 1089 help 1090 Enable command for setting manual background operations handshake 1091 on a eMMC device. The feature is optionally available on eMMC devices 1092 conforming to standard >= 4.41. 1093 1094config CMD_BLOCK_CACHE 1095 bool "blkcache - control and stats for block cache" 1096 depends on BLOCK_CACHE 1097 default y if BLOCK_CACHE 1098 help 1099 Enable the blkcache command, which can be used to control the 1100 operation of the cache functions. 1101 This is most useful when fine-tuning the operation of the cache 1102 during development, but also allows the cache to be disabled when 1103 it might hurt performance (e.g. when using the ums command). 1104 1105config CMD_CACHE 1106 bool "icache or dcache" 1107 help 1108 Enable the "icache" and "dcache" commands 1109 1110config CMD_DISPLAY 1111 bool "Enable the 'display' command, for character displays" 1112 help 1113 (this needs porting to driver model) 1114 This enables the 'display' command which allows a string to be 1115 displayed on a simple board-specific display. Implement 1116 display_putc() to use it. 1117 1118config CMD_LED 1119 bool "led" 1120 default y if LED 1121 help 1122 Enable the 'led' command which allows for control of LEDs supported 1123 by the board. The LEDs can be listed with 'led list' and controlled 1124 with led on/off/togle/blink. Any LED drivers can be controlled with 1125 this command, e.g. led_gpio. 1126 1127config CMD_DATE 1128 bool "date" 1129 default y if DM_RTC 1130 help 1131 Enable the 'date' command for getting/setting the time/date in RTC 1132 devices. 1133 1134config CMD_TIME 1135 bool "time" 1136 help 1137 Run commands and summarize execution time. 1138 1139config CMD_GETTIME 1140 bool "gettime - read elapsed time" 1141 help 1142 Enable the 'gettime' command which reads the elapsed time since 1143 U-Boot started running. This shows the time in seconds and 1144 milliseconds. See also the 'bootstage' command which provides more 1145 flexibility for boot timing. 1146 1147# TODO: rename to CMD_SLEEP 1148config CMD_MISC 1149 bool "sleep" 1150 default y 1151 help 1152 Delay execution for some time 1153 1154config CMD_TIMER 1155 bool "timer" 1156 help 1157 Access the system timer. 1158 1159config CMD_SOUND 1160 bool "sound" 1161 depends on SOUND 1162 help 1163 This provides basic access to the U-Boot's sound support. The main 1164 feature is to play a beep. 1165 1166 sound init - set up sound system 1167 sound play - play a sound 1168 1169config CMD_QFW 1170 bool "qfw" 1171 select QFW 1172 help 1173 This provides access to the QEMU firmware interface. The main 1174 feature is to allow easy loading of files passed to qemu-system 1175 via -kernel / -initrd 1176 1177source "cmd/mvebu/Kconfig" 1178 1179config CMD_TERMINAL 1180 bool "terminal - provides a way to attach a serial terminal" 1181 help 1182 Provides a 'cu'-like serial terminal command. This can be used to 1183 access other serial ports from the system console. The terminal 1184 is very simple with no special processing of characters. As with 1185 cu, you can press ~. (tilde followed by period) to exit. 1186 1187config CMD_UUID 1188 bool "uuid, guid - generation of unique IDs" 1189 help 1190 This enables two commands: 1191 1192 uuid - generate random Universally Unique Identifier 1193 guid - generate Globally Unique Identifier based on random UUID 1194 1195 The two commands are very similar except for the endianness of the 1196 output. 1197 1198endmenu 1199 1200config CMD_BOOTSTAGE 1201 bool "Enable the 'bootstage' command" 1202 depends on BOOTSTAGE 1203 help 1204 Add a 'bootstage' command which supports printing a report 1205 and un/stashing of bootstage data. 1206 1207menu "Power commands" 1208config CMD_PMIC 1209 bool "Enable Driver Model PMIC command" 1210 depends on DM_PMIC 1211 help 1212 This is the pmic command, based on a driver model pmic's API. 1213 Command features are unchanged: 1214 - list - list pmic devices 1215 - pmic dev <id> - show or [set] operating pmic device (NEW) 1216 - pmic dump - dump registers 1217 - pmic read address - read byte of register at address 1218 - pmic write address - write byte to register at address 1219 The only one change for this command is 'dev' subcommand. 1220 1221config CMD_REGULATOR 1222 bool "Enable Driver Model REGULATOR command" 1223 depends on DM_REGULATOR 1224 help 1225 This command is based on driver model regulator's API. 1226 User interface features: 1227 - list - list regulator devices 1228 - regulator dev <id> - show or [set] operating regulator device 1229 - regulator info - print constraints info 1230 - regulator status - print operating status 1231 - regulator value <val] <-f> - print/[set] voltage value [uV] 1232 - regulator current <val> - print/[set] current value [uA] 1233 - regulator mode <id> - print/[set] operating mode id 1234 - regulator enable - enable the regulator output 1235 - regulator disable - disable the regulator output 1236 1237 The '-f' (force) option can be used for set the value which exceeds 1238 the limits, which are found in device-tree and are kept in regulator's 1239 uclass platdata structure. 1240 1241config CMD_CHARGE_DISPLAY 1242 bool "Enable Driver Model Charge Display command" 1243 help 1244 Support U-Boot charge display. 1245 1246endmenu 1247 1248menu "Security commands" 1249config CMD_AES 1250 bool "Enable the 'aes' command" 1251 select AES 1252 help 1253 This provides a means to encrypt and decrypt data using the AES 1254 (Advanced Encryption Standard). This algorithm uses a symetric key 1255 and is widely used as a streaming cipher. Different key lengths are 1256 supported by the algorithm but this command only supports 128 bits 1257 at present. 1258 1259config CMD_BLOB 1260 bool "Enable the 'blob' command" 1261 help 1262 This is used with the Freescale secure boot mechanism. 1263 1264 Freescale's SEC block has built-in Blob Protocol which provides 1265 a method for protecting user-defined data across system power 1266 cycles. SEC block protects data in a data structure called a Blob, 1267 which provides both confidentiality and integrity protection. 1268 1269 Encapsulating data as a blob 1270 Each time that the Blob Protocol is used to protect data, a 1271 different randomly generated key is used to encrypt the data. 1272 This random key is itself encrypted using a key which is derived 1273 from SoC's non-volatile secret key and a 16 bit Key identifier. 1274 The resulting encrypted key along with encrypted data is called a 1275 blob. The non-volatile secure key is available for use only during 1276 secure boot. 1277 1278 During decapsulation, the reverse process is performed to get back 1279 the original data. 1280 1281 Sub-commands: 1282 blob enc - encapsulating data as a cryptgraphic blob 1283 blob dec - decapsulating cryptgraphic blob to get the data 1284 1285 Syntax: 1286 1287 blob enc src dst len km 1288 1289 Encapsulate and create blob of data $len bytes long 1290 at address $src and store the result at address $dst. 1291 $km is the 16 byte key modifier is also required for 1292 generation/use as key for cryptographic operation. Key 1293 modifier should be 16 byte long. 1294 1295 blob dec src dst len km 1296 1297 Decapsulate the blob of data at address $src and 1298 store result of $len byte at addr $dst. 1299 $km is the 16 byte key modifier is also required for 1300 generation/use as key for cryptographic operation. Key 1301 modifier should be 16 byte long. 1302 1303config CMD_HASH 1304 bool "Support 'hash' command" 1305 select HASH 1306 help 1307 This provides a way to hash data in memory using various supported 1308 algorithms (such as SHA1, MD5, CRC32). The computed digest can be 1309 saved to memory or to an environment variable. It is also possible 1310 to verify a hash against data in memory. 1311 1312config HASH_VERIFY 1313 bool "hash -v" 1314 depends on CMD_HASH 1315 help 1316 Add -v option to verify data against a hash. 1317 1318config CMD_TPM 1319 bool "Enable the 'tpm' command" 1320 depends on TPM 1321 help 1322 This provides a means to talk to a TPM from the command line. A wide 1323 range of commands if provided - see 'tpm help' for details. The 1324 command requires a suitable TPM on your board and the correct driver 1325 must be enabled. 1326 1327config CMD_TPM_TEST 1328 bool "Enable the 'tpm test' command" 1329 depends on CMD_TPM 1330 help 1331 This provides a a series of tests to confirm that the TPM is working 1332 correctly. The tests cover initialisation, non-volatile RAM, extend, 1333 global lock and checking that timing is within expectations. The 1334 tests pass correctly on Infineon TPMs but may need to be adjusted 1335 for other devices. 1336 1337endmenu 1338 1339menu "Firmware commands" 1340config CMD_CROS_EC 1341 bool "Enable crosec command" 1342 depends on CROS_EC 1343 default y 1344 help 1345 Enable command-line access to the Chrome OS EC (Embedded 1346 Controller). This provides the 'crosec' command which has 1347 a number of sub-commands for performing EC tasks such as 1348 updating its flash, accessing a small saved context area 1349 and talking to the I2C bus behind the EC (if there is one). 1350endmenu 1351 1352menu "Filesystem commands" 1353config CMD_CBFS 1354 bool "Enable the 'cbfs' command" 1355 depends on FS_CBFS 1356 help 1357 Define this to enable support for reading from a Coreboot 1358 filesystem. This is a ROM-based filesystem used for accessing files 1359 on systems that use coreboot as the first boot-loader and then load 1360 U-Boot to actually boot the Operating System. Available commands are 1361 cbfsinit, cbfsinfo, cbfsls and cbfsload. 1362 1363config CMD_CRAMFS 1364 bool "Enable the 'cramfs' command" 1365 depends on FS_CRAMFS 1366 help 1367 This provides commands for dealing with CRAMFS (Compressed ROM 1368 filesystem). CRAMFS is useful when space is tight since files are 1369 compressed. Two commands are provided: 1370 1371 cramfsls - lists files in a cramfs image 1372 cramfsload - loads a file from a cramfs image 1373 1374config CMD_EXT2 1375 bool "ext2 command support" 1376 help 1377 Enables EXT2 FS command 1378 1379config CMD_EXT4 1380 bool "ext4 command support" 1381 help 1382 Enables EXT4 FS command 1383 1384config CMD_EXT4_WRITE 1385 depends on CMD_EXT4 1386 bool "ext4 write command support" 1387 help 1388 Enables EXT4 FS write command 1389 1390config CMD_FAT 1391 bool "FAT command support" 1392 select FS_FAT 1393 help 1394 Support for the FAT fs 1395 1396config CMD_FS_GENERIC 1397 bool "filesystem commands" 1398 help 1399 Enables filesystem commands (e.g. load, ls) that work for multiple 1400 fs types. 1401 1402config CMD_FS_UUID 1403 bool "fsuuid command" 1404 help 1405 Enables fsuuid command for filesystem UUID. 1406 1407config CMD_JFFS2 1408 bool "jffs2 command" 1409 select FS_JFFS2 1410 help 1411 Enables commands to support the JFFS2 (Journalling Flash File System 1412 version 2) filesystem. This enables fsload, ls and fsinfo which 1413 provide the ability to load files, list directories and obtain 1414 filesystem information. 1415 1416config CMD_MTDPARTS 1417 bool "MTD partition support" 1418 help 1419 MTD partition support 1420 1421config MTDIDS_DEFAULT 1422 string "Default MTD IDs" 1423 depends on CMD_MTDPARTS 1424 help 1425 Defines a default MTD ID 1426 1427config MTDPARTS_DEFAULT 1428 string "Default MTD partition scheme" 1429 depends on CMD_MTDPARTS 1430 help 1431 Defines a default MTD partitioning scheme in the Linux MTD command 1432 line partitions format 1433 1434config CMD_MTDPARTS_SPREAD 1435 bool "Padd partition size to take account of bad blocks" 1436 depends on CMD_MTDPARTS 1437 help 1438 This enables the 'spread' sub-command of the mtdparts command. 1439 This command will modify the existing mtdparts variable by increasing 1440 the size of the partitions such that 1) each partition's net size is 1441 at least as large as the size specified in the mtdparts variable and 1442 2) each partition starts on a good block. 1443 1444config CMD_REISER 1445 bool "reiser - Access to reiserfs filesystems" 1446 help 1447 This provides two commands which operate on a resierfs filesystem, 1448 commonly used some years ago: 1449 1450 reiserls - list files 1451 reiserload - load a file 1452 1453config CMD_SCSI 1454 bool "scsi - Access to SCSI devices" 1455 default y if SCSI 1456 help 1457 This provides a 'scsi' command which provides access to SCSI (Small 1458 Computer System Interface) devices. The command provides a way to 1459 scan the bus, reset the bus, read and write data and get information 1460 about devices. 1461 1462config CMD_YAFFS2 1463 bool "yaffs2 - Access of YAFFS2 filesystem" 1464 depends on YAFFS2 1465 default y 1466 help 1467 This provides commands for accessing a YAFFS2 filesystem. Yet 1468 Another Flash Filesystem 2 is a filesystem designed specifically 1469 for NAND flash. It incorporates bad-block management and ensures 1470 that device writes are sequential regardless of filesystem 1471 activity. 1472 1473config CMD_ZFS 1474 bool "zfs - Access of ZFS filesystem" 1475 help 1476 This provides commands to accessing a ZFS filesystem, commonly used 1477 on Solaris systems. Two sub-commands are provided: 1478 1479 zfsls - list files in a directory 1480 zfsload - load a file 1481 1482 See doc/README.zfs for more details. 1483 1484endmenu 1485 1486menu "Debug commands" 1487 1488config CMD_BEDBUG 1489 bool "bedbug" 1490 help 1491 The bedbug (emBEDded deBUGger) command provides debugging features 1492 for some PowerPC processors. For details please see the 1493 docuemntation in doc/README.beddbug 1494 1495config CMD_DIAG 1496 bool "diag - Board diagnostics" 1497 help 1498 This command provides access to board diagnostic tests. These are 1499 called Power-on Self Tests (POST). The command allows listing of 1500 available tests and running either all the tests, or specific tests 1501 identified by name. 1502 1503config CMD_IRQ 1504 bool "irq - Show information about interrupts" 1505 depends on !ARM && !MIPS && !SH 1506 help 1507 This enables two commands: 1508 1509 interrupts - enable or disable interrupts 1510 irqinfo - print device-specific interrupt information 1511 1512config CMD_KGDB 1513 bool "kgdb - Allow debugging of U-Boot with gdb" 1514 help 1515 This enables a 'kgdb' command which allows gdb to connect to U-Boot 1516 over a serial link for debugging purposes. This allows 1517 single-stepping, inspecting variables, etc. This is supported only 1518 on PowerPC at present. 1519 1520config CMD_TRACE 1521 bool "trace - Support tracing of function calls and timing" 1522 help 1523 Enables a command to control using of function tracing within 1524 U-Boot. This allows recording of call traces including timing 1525 information. The command can write data to memory for exporting 1526 for analsys (e.g. using bootchart). See doc/README.trace for full 1527 details. 1528 1529endmenu 1530 1531config CMD_UBI 1532 tristate "Enable UBI - Unsorted block images commands" 1533 select CRC32 1534 select MTD_UBI 1535 select CMD_MTDPARTS 1536 default y if NAND_SUNXI 1537 help 1538 UBI is a software layer above MTD layer which admits use of LVM-like 1539 logical volumes on top of MTD devices, hides some complexities of 1540 flash chips like wear and bad blocks and provides some other useful 1541 capabilities. Please, consult the MTD web site for more details 1542 (www.linux-mtd.infradead.org). Activate this option if you want 1543 to use U-Boot UBI commands. 1544 1545config CMD_UBIFS 1546 tristate "Enable UBIFS - Unsorted block images filesystem commands" 1547 depends on CMD_UBI 1548 select CRC32 1549 select LZO 1550 default y if CMD_UBI 1551 help 1552 UBIFS is a file system for flash devices which works on top of UBI. 1553 1554endmenu 1555