xref: /rk3399_ARM-atf/plat/socionext/uniphier/uniphier_console_setup.c (revision 452afcfb0cc8a79a8e0801a0cc7ee3c2c84875bf)

/*
 * Copyright (c) 2019-2025, Socionext Inc. All rights reserved.
 *
 * SPDX-License-Identifier: BSD-3-Clause
 */

#include <assert.h>

#include <drivers/console.h>
#include <errno.h>
#include <lib/mmio.h>
#include <plat/common/platform.h>

#include "uniphier.h"
#include "uniphier_console.h"

#define UNIPHIER_UART_OFFSET	0x100
#define UNIPHIER_UART_NR_PORTS	4

/* These callbacks are implemented in assembly to use crash_console_helpers.S */
int uniphier_console_putc(int character, console_t *console);
int uniphier_console_getc(console_t *console);
void uniphier_console_flush(console_t *console);

static console_t uniphier_console = {
	.flags = CONSOLE_FLAG_BOOT |
#if DEBUG
		 CONSOLE_FLAG_RUNTIME |
#endif
		 CONSOLE_FLAG_CRASH |
		 CONSOLE_FLAG_TRANSLATE_CRLF,
	.putc = uniphier_console_putc,
#if ENABLE_CONSOLE_GETC
	.getc = uniphier_console_getc,
#endif
	.flush = uniphier_console_flush,
};

static const uintptr_t uniphier_uart_base[] = {
	[UNIPHIER_SOC_LD11] = 0x54006800,
	[UNIPHIER_SOC_LD20] = 0x54006800,
	[UNIPHIER_SOC_PXS3] = 0x54006800,
};

/*
 * There are 4 UART ports available on this platform. By default, we want to
 * use the same one as used in the previous firmware stage.
 */
static uintptr_t uniphier_console_get_base(unsigned int soc)
{
	uintptr_t base, end;
	uint32_t div;

	assert(soc < ARRAY_SIZE(uniphier_uart_base));
	base = uniphier_uart_base[soc];
	end = base + UNIPHIER_UART_OFFSET * UNIPHIER_UART_NR_PORTS;

	while (base < end) {
		div = mmio_read_32(base + UNIPHIER_UART_DLR);
		if (div)
			return base;
		base += UNIPHIER_UART_OFFSET;
	}

	return 0;
}

static void uniphier_console_init(uintptr_t base)
{
	mmio_write_32(base + UNIPHIER_UART_FCR, UNIPHIER_UART_FCR_ENABLE_FIFO);
	mmio_write_32(base + UNIPHIER_UART_LCR_MCR,
		      UNIPHIER_UART_LCR_WLEN8 << 8);
}

void uniphier_console_setup(unsigned int soc)
{
	uintptr_t base;

	base = uniphier_console_get_base(soc);
	if (!base)
		plat_error_handler(-EINVAL);

	uniphier_console.base = base;
	console_register(&uniphier_console);

	/*
	 * The hardware might be still printing characters queued up in the
	 * previous firmware stage. Make sure the transmitter is empty before
	 * any initialization. Otherwise, the console might get corrupted.
	 */
	console_flush();

	uniphier_console_init(base);
}