xref: /rk3399_ARM-atf/plat/rpi/rpi3/include/platform_def.h (revision 4666d046489a865f6434d7925903e0365da44575)

/*
 * Copyright (c) 2015-2018, ARM Limited and Contributors. All rights reserved.
 *
 * SPDX-License-Identifier: BSD-3-Clause
 */

#ifndef PLATFORM_DEF_H
#define PLATFORM_DEF_H

#include <arch.h>
#include <common/tbbr/tbbr_img_def.h>
#include <lib/utils_def.h>
#include <plat/common/common_def.h>

#include "rpi_hw.h"

/* Special value used to verify platform parameters from BL2 to BL31 */
#define RPI3_BL31_PLAT_PARAM_VAL	ULL(0x0F1E2D3C4B5A6978)

#define PLATFORM_STACK_SIZE		ULL(0x1000)

#define PLATFORM_MAX_CPUS_PER_CLUSTER	U(4)
#define PLATFORM_CLUSTER_COUNT		U(1)
#define PLATFORM_CLUSTER0_CORE_COUNT	PLATFORM_MAX_CPUS_PER_CLUSTER
#define PLATFORM_CORE_COUNT		PLATFORM_CLUSTER0_CORE_COUNT

#define RPI3_PRIMARY_CPU		U(0)

#define PLAT_MAX_PWR_LVL		MPIDR_AFFLVL1
#define PLAT_NUM_PWR_DOMAINS		(PLATFORM_CLUSTER_COUNT + \
					 PLATFORM_CORE_COUNT)

#define PLAT_MAX_RET_STATE		U(1)
#define PLAT_MAX_OFF_STATE		U(2)

/* Local power state for power domains in Run state. */
#define PLAT_LOCAL_STATE_RUN		U(0)
/* Local power state for retention. Valid only for CPU power domains */
#define PLAT_LOCAL_STATE_RET		U(1)
/*
 * Local power state for OFF/power-down. Valid for CPU and cluster power
 * domains.
 */
#define PLAT_LOCAL_STATE_OFF		U(2)

/*
 * Macros used to parse state information from State-ID if it is using the
 * recommended encoding for State-ID.
 */
#define PLAT_LOCAL_PSTATE_WIDTH		U(4)
#define PLAT_LOCAL_PSTATE_MASK		((U(1) << PLAT_LOCAL_PSTATE_WIDTH) - 1)

/*
 * Some data must be aligned on the biggest cache line size in the platform.
 * This is known only to the platform as it might have a combination of
 * integrated and external caches.
 */
#define CACHE_WRITEBACK_SHIFT		U(6)
#define CACHE_WRITEBACK_GRANULE		(U(1) << CACHE_WRITEBACK_SHIFT)

/*
 * Partition memory into secure ROM, non-secure DRAM, secure "SRAM", and
 * secure DRAM. Note that this is all actually DRAM with different names,
 * there is no Secure RAM in the Raspberry Pi 3.
 */
#if RPI3_USE_UEFI_MAP
#define SEC_ROM_BASE			ULL(0x00000000)
#define SEC_ROM_SIZE			ULL(0x00010000)

/* FIP placed after ROM to append it to BL1 with very little padding. */
#define PLAT_RPI3_FIP_BASE		ULL(0x00020000)
#define PLAT_RPI3_FIP_MAX_SIZE		ULL(0x00010000)

/* Reserve 2M of secure SRAM and DRAM, starting at 2M */
#define SEC_SRAM_BASE			ULL(0x00200000)
#define SEC_SRAM_SIZE			ULL(0x00100000)

#define SEC_DRAM0_BASE			ULL(0x00300000)
#define SEC_DRAM0_SIZE			ULL(0x00100000)

/* Windows on ARM requires some RAM at 4M */
#define NS_DRAM0_BASE			ULL(0x00400000)
#define NS_DRAM0_SIZE			ULL(0x00C00000)
#else
#define SEC_ROM_BASE			ULL(0x00000000)
#define SEC_ROM_SIZE			ULL(0x00020000)

/* FIP placed after ROM to append it to BL1 with very little padding. */
#define PLAT_RPI3_FIP_BASE		ULL(0x00020000)
#define PLAT_RPI3_FIP_MAX_SIZE		ULL(0x001E0000)

/* We have 16M of memory reserved starting at 256M */
#define SEC_SRAM_BASE			ULL(0x10000000)
#define SEC_SRAM_SIZE			ULL(0x00100000)

#define SEC_DRAM0_BASE			ULL(0x10100000)
#define SEC_DRAM0_SIZE			ULL(0x00F00000)
/* End of reserved memory */

#define NS_DRAM0_BASE			ULL(0x11000000)
#define NS_DRAM0_SIZE			ULL(0x01000000)
#endif /* RPI3_USE_UEFI_MAP */

/*
 * BL33 entrypoint.
 */
#define PLAT_RPI3_NS_IMAGE_OFFSET	NS_DRAM0_BASE
#define PLAT_RPI3_NS_IMAGE_MAX_SIZE	NS_DRAM0_SIZE

/*
 * I/O registers.
 */
#define DEVICE0_BASE			RPI3_IO_BASE
#define DEVICE0_SIZE			RPI3_IO_SIZE

/*
 * Arm TF lives in SRAM, partition it here
 */
#define SHARED_RAM_BASE			SEC_SRAM_BASE
#define SHARED_RAM_SIZE			ULL(0x00001000)

#define BL_RAM_BASE			(SHARED_RAM_BASE + SHARED_RAM_SIZE)
#define BL_RAM_SIZE			(SEC_SRAM_SIZE - SHARED_RAM_SIZE)

/*
 * Mailbox to control the secondary cores.All secondary cores are held in a wait
 * loop in cold boot. To release them perform the following steps (plus any
 * additional barriers that may be needed):
 *
 *     uint64_t *entrypoint = (uint64_t *)PLAT_RPI3_TM_ENTRYPOINT;
 *     *entrypoint = ADDRESS_TO_JUMP_TO;
 *
 *     uint64_t *mbox_entry = (uint64_t *)PLAT_RPI3_TM_HOLD_BASE;
 *     mbox_entry[cpu_id] = PLAT_RPI3_TM_HOLD_STATE_GO;
 *
 *     sev();
 */
#define PLAT_RPI3_TRUSTED_MAILBOX_BASE	SHARED_RAM_BASE

/* The secure entry point to be used on warm reset by all CPUs. */
#define PLAT_RPI3_TM_ENTRYPOINT		PLAT_RPI3_TRUSTED_MAILBOX_BASE
#define PLAT_RPI3_TM_ENTRYPOINT_SIZE	ULL(8)

/* Hold entries for each CPU. */
#define PLAT_RPI3_TM_HOLD_BASE		(PLAT_RPI3_TM_ENTRYPOINT + \
					 PLAT_RPI3_TM_ENTRYPOINT_SIZE)
#define PLAT_RPI3_TM_HOLD_ENTRY_SIZE	ULL(8)
#define PLAT_RPI3_TM_HOLD_SIZE		(PLAT_RPI3_TM_HOLD_ENTRY_SIZE * \
					 PLATFORM_CORE_COUNT)

#define PLAT_RPI3_TRUSTED_MAILBOX_SIZE	(PLAT_RPI3_TM_ENTRYPOINT_SIZE + \
					 PLAT_RPI3_TM_HOLD_SIZE)

#define PLAT_RPI3_TM_HOLD_STATE_WAIT	ULL(0)
#define PLAT_RPI3_TM_HOLD_STATE_GO	ULL(1)

/*
 * BL1 specific defines.
 *
 * BL1 RW data is relocated from ROM to RAM at runtime so we need 2 sets of
 * addresses.
 *
 * Put BL1 RW at the top of the Secure SRAM. BL1_RW_BASE is calculated using
 * the current BL1 RW debug size plus a little space for growth.
 */
#define PLAT_MAX_BL1_RW_SIZE		ULL(0x12000)

#define BL1_RO_BASE			SEC_ROM_BASE
#define BL1_RO_LIMIT			(SEC_ROM_BASE + SEC_ROM_SIZE)
#define BL1_RW_BASE			(BL1_RW_LIMIT - PLAT_MAX_BL1_RW_SIZE)
#define BL1_RW_LIMIT			(BL_RAM_BASE + BL_RAM_SIZE)

/*
 * BL2 specific defines.
 *
 * Put BL2 just below BL31. BL2_BASE is calculated using the current BL2 debug
 * size plus a little space for growth.
 */
#define PLAT_MAX_BL2_SIZE		ULL(0x2C000)

#define BL2_BASE			(BL2_LIMIT - PLAT_MAX_BL2_SIZE)
#define BL2_LIMIT			BL31_BASE

/*
 * BL31 specific defines.
 *
 * Put BL31 at the top of the Trusted SRAM. BL31_BASE is calculated using the
 * current BL31 debug size plus a little space for growth.
 */
#define PLAT_MAX_BL31_SIZE		ULL(0x20000)

#define BL31_BASE			(BL31_LIMIT - PLAT_MAX_BL31_SIZE)
#define BL31_LIMIT			(BL_RAM_BASE + BL_RAM_SIZE)
#define BL31_PROGBITS_LIMIT		BL1_RW_BASE

/*
 * BL32 specific defines.
 *
 * BL32 can execute from Secure SRAM or Secure DRAM.
 */
#define BL32_SRAM_BASE			BL_RAM_BASE
#define BL32_SRAM_LIMIT			BL31_BASE
#define BL32_DRAM_BASE			SEC_DRAM0_BASE
#define BL32_DRAM_LIMIT			(SEC_DRAM0_BASE + SEC_DRAM0_SIZE)

#ifdef SPD_opteed
/* Load pageable part of OP-TEE at end of allocated DRAM space for BL32 */
#define RPI3_OPTEE_PAGEABLE_LOAD_SIZE	0x080000 /* 512KB */
#define RPI3_OPTEE_PAGEABLE_LOAD_BASE	(BL32_DRAM_LIMIT - \
					 RPI3_OPTEE_PAGEABLE_LOAD_SIZE)
#endif

#define SEC_SRAM_ID			0
#define SEC_DRAM_ID			1

#if RPI3_BL32_RAM_LOCATION_ID == SEC_SRAM_ID
# define BL32_MEM_BASE			BL_RAM_BASE
# define BL32_MEM_SIZE			BL_RAM_SIZE
# define BL32_BASE			BL32_SRAM_BASE
# define BL32_LIMIT			BL32_SRAM_LIMIT
#elif RPI3_BL32_RAM_LOCATION_ID == SEC_DRAM_ID
# define BL32_MEM_BASE			SEC_DRAM0_BASE
# define BL32_MEM_SIZE			SEC_DRAM0_SIZE
# define BL32_BASE			BL32_DRAM_BASE
# define BL32_LIMIT			BL32_DRAM_LIMIT
#else
# error "Unsupported RPI3_BL32_RAM_LOCATION_ID value"
#endif
#define BL32_SIZE			(BL32_LIMIT - BL32_BASE)

#ifdef SPD_none
#undef BL32_BASE
#endif /* SPD_none */

/*
 * Other memory-related defines.
 */
#define PLAT_PHY_ADDR_SPACE_SIZE	(ULL(1) << 32)
#define PLAT_VIRT_ADDR_SPACE_SIZE	(ULL(1) << 32)

#define MAX_MMAP_REGIONS		8
#define MAX_XLAT_TABLES			4

#define MAX_IO_DEVICES			U(3)
#define MAX_IO_HANDLES			U(4)

#define MAX_IO_BLOCK_DEVICES		U(1)

/*
 * Serial-related constants.
 */
#define PLAT_RPI3_UART_BASE		RPI3_MINI_UART_BASE
#define PLAT_RPI3_UART_CLK_IN_HZ	RPI3_MINI_UART_CLK_IN_HZ
#define PLAT_RPI3_UART_BAUDRATE		ULL(115200)

/*
 * System counter
 */
#define SYS_COUNTER_FREQ_IN_TICKS	ULL(19200000)

#endif /* PLATFORM_DEF_H */