1 /* 2 * Copyright (C) 2018 Marvell International Ltd. 3 * 4 * SPDX-License-Identifier: BSD-3-Clause 5 * https://spdx.org/licenses 6 */ 7 8 #include <arch_helpers.h> 9 #include <common/debug.h> 10 #include <drivers/mentor/mi2cv.h> 11 #include <lib/mmio.h> 12 13 #include <mv_ddr_if.h> 14 #include <mvebu_def.h> 15 #include <plat_marvell.h> 16 17 #define MVEBU_AP_MPP_CTRL0_7_REG MVEBU_AP_MPP_REGS(0) 18 #define MVEBU_AP_MPP_CTRL4_OFFS 16 19 #define MVEBU_AP_MPP_CTRL5_OFFS 20 20 #define MVEBU_AP_MPP_CTRL4_I2C0_SDA_ENA 0x3 21 #define MVEBU_AP_MPP_CTRL5_I2C0_SCK_ENA 0x3 22 23 #define MVEBU_CP_MPP_CTRL37_OFFS 20 24 #define MVEBU_CP_MPP_CTRL38_OFFS 24 25 #define MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA 0x2 26 #define MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA 0x2 27 28 #define MVEBU_MPP_CTRL_MASK 0xf 29 30 /* 31 * This struct provides the DRAM training code with 32 * the appropriate board DRAM configuration 33 */ 34 static struct mv_ddr_topology_map board_topology_map = { 35 /* MISL board with 1CS 8Gb x4 devices of Micron 2400T */ 36 DEBUG_LEVEL_ERROR, 37 0x1, /* active interfaces */ 38 /* cs_mask, mirror, dqs_swap, ck_swap X subphys */ 39 { { { {0x1, 0x0, 0, 0}, /* FIXME: change the cs mask for all 64 bit */ 40 {0x1, 0x0, 0, 0}, 41 {0x1, 0x0, 0, 0}, 42 {0x1, 0x0, 0, 0}, 43 {0x1, 0x0, 0, 0}, 44 {0x1, 0x0, 0, 0}, 45 {0x1, 0x0, 0, 0}, 46 {0x1, 0x0, 0, 0}, 47 {0x1, 0x0, 0, 0} }, 48 /* TODO: double check if the speed bin is 2400T */ 49 SPEED_BIN_DDR_2400T, /* speed_bin */ 50 MV_DDR_DEV_WIDTH_8BIT, /* sdram device width */ 51 MV_DDR_DIE_CAP_8GBIT, /* die capacity */ 52 MV_DDR_FREQ_SAR, /* frequency */ 53 0, 0, /* cas_l, cas_wl */ 54 MV_DDR_TEMP_LOW} }, /* temperature */ 55 MV_DDR_64BIT_ECC_PUP8_BUS_MASK, /* subphys mask */ 56 MV_DDR_CFG_SPD, /* ddr configuration data source */ 57 { {0} }, /* raw spd data */ 58 {0}, /* timing parameters */ 59 { /* electrical configuration */ 60 { /* memory electrical configuration */ 61 MV_DDR_RTT_NOM_PARK_RZQ_DISABLE, /* rtt_nom */ 62 { 63 MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */ 64 MV_DDR_RTT_NOM_PARK_RZQ_DIV1 /* rtt_park 2cs */ 65 }, 66 { 67 MV_DDR_RTT_WR_DYN_ODT_OFF, /* rtt_wr 1cs */ 68 MV_DDR_RTT_WR_RZQ_DIV2 /* rtt_wr 2cs */ 69 }, 70 MV_DDR_DIC_RZQ_DIV7 /* dic */ 71 }, 72 { /* phy electrical configuration */ 73 MV_DDR_OHM_30, /* data_drv_p */ 74 MV_DDR_OHM_30, /* data_drv_n */ 75 MV_DDR_OHM_30, /* ctrl_drv_p */ 76 MV_DDR_OHM_30, /* ctrl_drv_n */ 77 { 78 MV_DDR_OHM_60, /* odt_p 1cs */ 79 MV_DDR_OHM_120 /* odt_p 2cs */ 80 }, 81 { 82 MV_DDR_OHM_60, /* odt_n 1cs */ 83 MV_DDR_OHM_120 /* odt_n 2cs */ 84 }, 85 }, 86 { /* mac electrical configuration */ 87 MV_DDR_ODT_CFG_NORMAL, /* odtcfg_pattern */ 88 MV_DDR_ODT_CFG_ALWAYS_ON, /* odtcfg_write */ 89 MV_DDR_ODT_CFG_NORMAL, /* odtcfg_read */ 90 }, 91 } 92 }; 93 94 struct mv_ddr_topology_map *mv_ddr_topology_map_get(void) 95 { 96 /* Return the board topology as defined in the board code */ 97 return &board_topology_map; 98 } 99 100 static void mpp_config(void) 101 { 102 uintptr_t reg; 103 uint32_t val; 104 105 reg = MVEBU_CP_MPP_REGS(0, 4); 106 /* configure CP0 MPP 37 and 38 to i2c */ 107 val = mmio_read_32(reg); 108 val &= ~((MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL37_OFFS) | 109 (MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL38_OFFS)); 110 val |= (MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA << 111 MVEBU_CP_MPP_CTRL37_OFFS) | 112 (MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA << 113 MVEBU_CP_MPP_CTRL38_OFFS); 114 mmio_write_32(reg, val); 115 } 116 117 /* 118 * This function may modify the default DRAM parameters 119 * based on information received from SPD or bootloader 120 * configuration located on non volatile storage 121 */ 122 void plat_marvell_dram_update_topology(void) 123 { 124 struct mv_ddr_topology_map *tm = mv_ddr_topology_map_get(); 125 126 INFO("Gathering DRAM information\n"); 127 128 if (tm->cfg_src == MV_DDR_CFG_SPD) { 129 /* configure MPPs to enable i2c */ 130 mpp_config(); 131 132 /* initialize i2c */ 133 i2c_init((void *)MVEBU_CP0_I2C_BASE); 134 135 /* select SPD memory page 0 to access DRAM configuration */ 136 i2c_write(I2C_SPD_P0_ADDR, 0x0, 1, tm->spd_data.all_bytes, 1); 137 138 /* read data from spd */ 139 i2c_read(I2C_SPD_ADDR, 0x0, 1, tm->spd_data.all_bytes, 140 sizeof(tm->spd_data.all_bytes)); 141 } 142 } 143